Characterization of degraded hydrogels based on poly(vinyl alcohol) grafted with poly(lactide‐co‐glycolide)

Poly(vinyl alcohol) (PVA) grafted with poly(lactide‐co‐glycolide) and cross‐linked as a material of increased hydrophobicity relative to PVA was produced. The properties were examined with respect to the mass loss, water uptake, hydrophilicity, and mechanical characteristics upon hydrolytical degradation. The hydrogels investigated display water uptake increasing with degradation time because of increasing hydrophilicity. The mass loss amounts up to 15% after eight weeks of degradation. The mechanical properties of the hydrogels are within the range of those of natural tissue, the E modulus is 18 MPa, or even 100–200 MPa, depending on the structure of material. The mechanical characteristic and their dependence degradation show the most recognizable correlation with the chemical structure. Studies of the topography of degraded samples (scanning electron microscopy) and IR measurements demonstrate the degradation to occur at slow rate due to the high degree of grafting. The mass loss is rather low and a bulk degradation mechanism takes place. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preparation of poly(DL‐lactide‐co‐glycolide) nanoparticles without surfactant

The preparation of poly(DL ‐lactide‐co‐glycolide) (PLGA) nanoparticles was performed by a dialysis method without surfactant or emulsifiers. The size of the PLGA nanoparticles prepared from dimethylacetamide (DMAc) as an initial solvent was smaller than that from acetone. The sizes of the PLGA nanoparticles from DMAc and acetone were 200.4 ± 133.0 and 642.3 ± 131.1 nm, respectively. The effects of the initial solvent selected to dissolve the copolymer and the lactide:glycolide ratio were investigated. The PLGA nanoparticles were spherical as revealed by the results of scanning electron microscopy and transmission electron microscopy observations. From these results it was shown that PLGA nanoparticles could be formed by the dialysis method without surfactant. The drug‐loading contents and efficiency were also dependent on the lactide:glycolide ratio and initial feeding amount of the drug. A higher lactide ratio resulted in higher drug loading and higher loading efficiency. However, a higher initial feeding amount of the drug resulted in higher drug loading and lower loading efficiency. Clonazepam was released for at least 2 days and the release rate was slower with a higher lactide:glycolide ratio and a larger amount of drug‐loading nanoparticles than that with a lower lactide:glycolide ratio and a smaller amount of drug‐loading nanoparticles. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2228–2236, 2001     

Thermosensitive nanoparticles prepared from poly(N‐isopropylacrylamide‐acrylamide‐vinilpyrrolidone) and its blend with poly(lactide‐co‐glycolide) for efficient drug delivery system

Temperature‐responsive polymers have become increasingly attractive as carrier for the injectable drug delivery systems. In the present work, we have studied the preparation of poly(N‐isopropylacrylamide‐acrylamide‐vinilpyrrolidone) (NIPAAm‐AAm‐VP terpolymer) nanoparticulated terpolymer and its blend with poly(lactide‐co‐glycolide, PLGA; molar ratio of lactide/glycolid 1/3). Thermosensitive terpolymer, poly(NIPAAm‐AAm‐VP) was prepared by free‐radical polymerization in aqueous solution. The nanoparticles of poly(NIPAAm‐AAm‐VP) and its blend with PLGA containing naltrexone were prepared using the evaporation and w/o emulsion‐solvent evaporation methods, respectively. Nanoparticles prepared from terpolymer‐PLGA blend at low polymer concentration (5%) shows larger particle size (>300 nm) and higher drug content%. Various types of nanoparticles showed a burst release of less than 10% after 24 h . The results suggest that by regulating different variables, desired release profiles of naltrexone can be achieved using a blend of PLGA‐poly(NIPAAm‐AAm‐VP) nanoparticulate system. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Poly(D,L‐lactide‐co‐glycolide)/poly(ethylenimine) blend matrix system for pH sensitive drug delivery

Poly(D ,L ‐lactide‐co‐glycolide) (PLGA) and poly(ethylenimine) (PEI) were blended and found to form a homogeneous pH sensitive matrix for drug release. Differential scanning calorimetry (DSC) studies of the PLGA/PEI blends showed a single glass transition temperature at all compositions. Fourier transform infrared spectroscopy (FTIR) demonstrated that the PLGA carbonyl peak at 1760 cm^?1 shifted to 1666 cm^?1 as a result of amide bond formation between the two polymers. This was confirmed by ¹³C nuclear magnetic resonance studies. A PLGA/PEI matrix of 90/10 weight ratio was chosen for evaluation for controlled drug release. Both hydrophobic β‐lapachone and hydrophilic rhodamine B showed pH dependent release profiles with faster release kinetics at lower pH values. The observed pH sensitive drug release was mainly attributed to two factors, pH dependent swelling and protonation of the PEI‐PLGA matrix. These results demonstrate utility of a PLGA/PEI matrix and its potential application in pH responsive drug delivery. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 89–96, 2006     

Comparison of the enthalpic relaxation of poly(lactide–co‐glycolide) 50:50 nanospheres and raw polymer

The phenomenon of enthalpic relaxation was evaluated for poly(lactide‐co‐glycolide) (PLGA, 50:50), in terms of storage of nanospheres for use as a controlled drug delivery system. Samples were stored for different times and temperatures below the glass transition temperature (T_g). Relaxation occurred at a significant rate up to 15 degrees below the T_g of 39.2°C. The effect of polymer morphology was considered by comparing the relaxation kinetics of the raw polymer with that of nanospheres formed using a novel technique. The nanospheres were shown to have a larger change in heat capacity at the glass transition and a longer average relaxation time than that of the raw polymer, and the relationship between these two parameters was discussed. For both the raw polymer and the nanospheres, relaxation was found to occur at a significant rate at room temperature. The storage of this system at subambient temperatures was therefore deemed important for maintaining the physicochemical properties of the system. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1868–1872, 2002     

Poly(lactide‐co‐glycolide) solution behavior in supercritical CO2, CHF3, and CHClF2

Cloud point and solution density data between 20 and 100°C and pressures to 3000 bar are presented for poly(lactide) (PLA) and poly(lactide‐co‐glycolide) (PLGA_x, where the molar concentration of glycolide in the backbone x ranges from 0 to 50 mol %) in supercritical CO₂, CHClF₂, and CHF₃. PLA dissolves in CO₂ at pressures near 1400 bar, in CHF₃ at pressures of 500 to 750 bar, and in CHClF₂ at pressures of 20–100 bar. As glycolide (GA) is added to the backbone of PLGA, the cloud point pressure increases by 50 bar/(mol GA) in CO₂, 25 bar/(mol GA) in CHF₃, and by only 2.5 bar/(mol GA) in CHClF₂. PLGA₅₀ does not dissolve in CO₂ to pressures of 3000 bar whereas it is readily soluble in CHClF₂ at pressures as low as 100 bar at 50°C. In comparison, the increases in cloud point pressure with increasing weight average molecular weight (M_w) are only approximately 2.3 bar/(1000 M_w) for PLGA copolymers in CO₂. The solution densities with all three SCF solvents range from 1.1 to 1.5 g/cm³ and they vary only by a small amount over the 80°C range used to obtain cloud point data. More than likely, the ability of the acidic hydrogen in CHF₃ and CHClF₂ to complex with the ester linkage in PLGA makes these better solvents than CO₂ especially since any change in favorable energetic interactions is magnified due to the liquid‐like densities exhibited by these SCF solvents. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 1155–1161, 2001     

Synthesis and characterization of an amphiphilic pluronic‐poly(D,L‐lactide‐co‐glycolide) copolymer and their nanoparticles as protein delivery systems

A new amphiphilic Pluronic (F68)‐PLGA copolymer, which can be used to prepare the stealth or long‐circulating nanoparticles, was synthesized with Pluronic (F68), DL ‐Lactide, and glycolide. The structures of Pluronic (F68)‐PLGA copolymer as the products were characterized with infrared spectrometry, nuclear magnetic resonance and their molecular weights were determined by gel permeation chromatography. Two methods, double emulsion (DE) and nanoprecipitation (NP), were employed to fabricate the polymeric nanoparticles. Bovine serum albumin (BSA) was loaded into nanoparticles as a model protein. Influence of the preparation conditions on the nanoparticles size, encapsulation efficiency, and release profile in vitro was investigated. They showed the entrapment efficiency of 42.9–63.4% and the average diameter of 119.1–342.8 nm depending on the fabrication technique of nanoparticles and the type of copolymer. The stability maintenance of BSA in the nanoparticle release in vitro was also measured via sodium dodecyl sulfate‐polyacrylamide gel electrophoresis (SDS‐PAGE), circular dichroism (CD), and fluorescence spectrometry. The results showed that the new copolymer could load BSA effectively and BSA kept stable after it was released from the nanoparticles. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Thermal properties of blends of poly(hydroxybutyrate‐co‐hydroxyvalerate) and poly(styrene‐co‐acrylonitrile)

Thermal properties of blends of poly(hydroxybutyrate‐co‐hydroxyvalerate) (PHBV) and poly(styrene‐co‐acrylonitrile) (SAN) prepared by solution casting were investigated by differential scanning calorimetry. In the study of PHBV‐SAN blends by differential scanning calorimetry, glass transition temperature and melting point of PHBV in the PHBV‐SAN blends were almost unchanged compared with those of the pure PHBV. This result indicates that the blends of PHBV and SAN are immiscible. However, crystallization temperature of the PHBV in the blends decreased approximately 9–15°. From the results of the Avrami analysis of PHBV in the PHBV‐SAN blends, crystallization rate constant of PHBV in the PHBV‐SAN blends decreased compared with that of the pure PHBV. From the above results, it is suggested that the nucleation of PHBV in the blends is suppressed by the addition of SAN. From the measured crystallization half time and degree of supercooling, interfacial free energy for the formation of heterogeneous nuclei of PHBV in the PHBV‐SAN blends was calculated and found to be 2360 (mN/m)³ for the pure PHBV and 2920–3120 (mN/m)³ for the blends. The values of interfacial free energy indicate that heterogeneity of PHBV in the PHBV‐SAN blends is deactivated by the SAN. This result is consistent with the results of crystallization temperature and crystallization rate constant of PHBV in the PHBV‐SAN blends. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 673–679, 2000     

Effect of glycolide monomer on release behavior of gentamicin sulfate‐loaded PLGA microparticles

For the treatment of osteomyelitis and the prevention of infections after orthopedic surgery, topically implantable gentamicin sulfate (GS)‐loaded poly(D ,L ‐lactide‐co‐glycolide) microparticles (GSMP) containing glycolide monomer (GM), as a biodegradable and nontoxic material, were prepared by melt‐extrusion method without organic solvent for controlled release. After preparation of polymer blend, the powders of different size (90–1200 μm) were obtained by means of freezer‐mill. The influences of GM and particle size were investigated on the GS release patterns. GSMP containing GM (in case of 10% loaded) showed a near‐zero order release from 2 to 7 days with the initial burst. GM affected to increase of GS release rate during the in vitro release test. The pH variations of the media were investigated to determine effect of GM on pH drop of media. The morphological evaluations, change of molecular weight, and thermal property of microparticles were characterized by scanning electron microscope, gel permeation chromatography, and differential scanning calorimeter, respectively. Bacterial inhibition zone test was established to identify antibiosis of GS. It showed antibiotic areas except control sample. From these results, the authors expected that GSMP containing GM would be a good dosage form as a topically implantable device that can get rid of lag period of GSMP. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1019–1025, 2007     

Effects of plasma treatment on biocompatibility of poly[(L‐lactide)‐co‐(ϵ‐caprolactone)] and poly[(L‐lactide)‐co‐glycolide] electrospun nanofibrous membranes

Poly[(l ‐lactide)‐co ‐(? ‐caprolactone)] (PLCL) and poly[(l ‐lactide)‐co ‐glycolide] (PLGA) copolymers are widely used in neural guide tissue regeneration. In this research, the surface modification of their hydrophilicity was achieved using plasma treatment. Attachment and proliferation of olfactory ensheathing cells on treated electrospun membranes increased by 26 and 32%, respectively, compared to the untreated PLCL and PLGA counterparts. Cells cultivated on both the PLCL and PLGA membranes showed high viability (>95%) and healthy morphologies with no evidence of cytotoxic effects. Cells grown on treated electrospun fibres displayed significant increases in mitochondrial activity and reductions in membrane leakage when compared to untreated samples. The results suggested that plasma treatment of the surface of the polymers enhanced both cell viability and growth without incurring any cytotoxic effects. © 2017 Society of Chemical Industry     

In vitro degradation and release profiles of poly‐DL‐lactide‐poly(ethylene glycol) microspheres with entrapped proteins

Poly‐DL ‐lactide (PLA) and poly‐DL ‐lactide‐poly(ethylene glycol) (PELA) were produced by bulk ring‐opening polymerization using stannous chloride as initiator. PLA, PELA microspheres, and PELA microspheres containing the outer membrane protein (OMP) of Leptospira interrogans with the size of 1.5–2 μm were prepared by a solvent evaporation process. In vitro degradation and release tests of PLA, PELA, and OMP‐loaded PELA microspheres were performed in pH 7.4 buffer solution at 37°C. Quantitatively, the degree of degradation was monitored by detecting the molecular weight reduction, by evaluating the mass loss and the apparent degradation rate constant, and by determining the intrinsic viscosity and poly(ethylene glycol) content of retrieved polymer, while the release profile was assessed by measuring the amount of protein presented in the release medium at various intervals. Qualitatively, the morphological changes of microspheres were observed with scanning electron micrography. The observed relative rates of mass loss versus molecular weight reduction are consistent with a bulk erosion process rather than surface erosion for PELA microspheres. The introduction of hydrophilic poly(ethylene glycol) domains in copolymer PELA and the presence of OMP within microspheres show critical influences on the degradation profile. The OMP‐loaded PELA microspheres present triphasic release profile and a close correlation is observed between the polymer degradation and the OMP release profiles. It is suggested that the polymer degradation rate, protein diffusion coefficient, and the water‐swollen structure of microspheres matrix commonly contribute to the OMP release from PELA microspheres. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 140–148, 2000     

In vitro Degradation of Poly[(L‐lactide)‐co‐(trimethylene carbonate)] Copolymers and a Composite with Poly[(L‐lactide)‐co‐glycolide] Fibers as Cardiovascular Stent Material

TMC/LLA copolymers with several TMC/LLA ratios are synthesized and a composite is obtained by reinforcing with short PLGA fibers. In vitro degradation is studied at 37 °C in pH = 7.4 buffer and compared with a PLLA homopolymer. The degradation of the copolymers appears slower than that of PLLA, showing that TMC units are more resistant to hydrolysis than LLA. Compositional changes indicate a preferential degradation of LLA units as compared to TMC ones. Morphological changes with crystallization of degradation by‐products are observed. The composite degrades much faster than the neat copolymer and PLLA because the faster degradation of PLGA fibers speeds up the degradation of the matrix. The composite appears promising for the fabrication of totally bioresorbable stents.

     

Properties and degradation behavior of surface functionalized MWCNT/poly(L‐lactide‐co‐ε‐caprolactone) biodegradable nanocomposites

In this research, poly(L ‐lactide‐co‐ε‐caprolactone) (PLACL) reinforced with well‐dispersed multiwalled carbon nanotubes (MWCNTs) nanocomposites were prepared by oxidization and functionalization of the MWCNT surfaces using oligomeric L ‐lactide (LA) and ε‐caprolactone (CL). It is found that the surface functionalization can effectively improve the dispersion and adhesion of MWCNTs in PLACL. The surface functionalization will have a significant effect on the physical, thermomechanical, and degradation properties of MWCNT/PLACL composites. The tensile modulus, yield stress, tensile strength, and elongation at break of composite increased 49%, 60%, 70%, and 94%, respectively, when the concentration of functionalized MWCNTs in composite is 2 wt %. The in vitro degradation rate of nanocomposites in phosphate buffer solution increased about 100%. The glass transition temperature (T_g) of composites was decreased when the concentration of functionalized MWCNTs is 0.5 wt %. With further increasing the concentration of functionalized MWCNTs, the T_g was increased. The degradation kinetics of nanocomposites can be engineered and functionalized by varying the contents of pristine or functionalized MWCNTs. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Poly(para‐dioxanone)/poly(D,L‐lactide) blends compatibilized with poly(D,L‐lactide‐co‐para‐dioxanone)

The effect of poly(D ,L ‐lactide‐co‐para‐dioxanone) (PLADO) as the compatibilizer on the properties of the blend of poly(para‐dioxanone) (PPDO) and poly(D ,L ‐lactide) (PDLLA) has been investigated. The 80/20 PPDO/PDLLA blends containing from 1% to 10% of random copolymer PLADO were prepared by solution coprecipitation. The PLADO component played a very important role in determining morphology, thermal, mechanical, and hydrophilic properties of the blends. Addition of PLADO into the blends could enhance the compatibility between dispersed PDLLA phase and PPDO matrix; the boundary between the two phases became unclear and even the smallest holes were not detected. On the other hand, the position of the T_g was composition dependent; when 5% PLADO was added into blend, the T_g distance between PPDO and PDLLA was shortened. The blends with various contents of compatibilizer had better mechanical properties compared with simple PPDO/PDLLA binary polymer blend, and such characteristics further improved as adding 5% random copolymers. The maximum observed tensile strength was 29.05 MPa for the compatibilized PPDO/PDLLA blend with 5% PLADO, whereas tensile strength of the uncompatibilized PPDO/PDLLA blend was 14.03 MPa, which was the lowest tensile strength. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Part 7. Effects of poly(L‐lactide‐co‐ϵ‐caprolactone) on morphology,structure, crystallization,and physical properties of blends of poly(L‐lactide) and poly(ϵ‐caprolactone)

Blended films of poly(L ‐lactide) [ie poly(L ‐lactic acid)] (PLLA) and poly(?‐caprolactone) (PCL) without or mixed with 10 wt% poly(L ‐lactide‐co‐?‐caprolactone) (PLLA‐CL) were prepared by solution‐casting. The effects of PLLA‐CL on the morphology, phase structure, crystallization, and mechanical properties of films have been investigated using polarization optical microscopy, scanning electron microscopy, differential scanning calorimetry and tensile testing. Addition of PLLA‐CL decreased number densities of spherulites in PLLA and PCL films, and improved the observability of spherulites and the smoothness of cross‐section of the PLLA/PCL blend film. The melting temperatures (T_m) of PLLA and PCL in the films remained unchanged upon addition of PLLA‐CL, while the crystallinities of PLLA and PCL increased at PLLA contents [X_PLLA = weight of PLLA/(weight of PLLA and PCL)] of 0.4–0.7 and at most of the X_PLLA values, respectively. The addition of PLLA‐CL improved the tensile strength and the Young modulus of the films at X_PLLA of 0.5–0.8 and of 0–0.1 and 0.5–0.8, respectively, and the elongation at break of the films at all the X_PLLA values. These findings strongly suggest that PLLA‐CL was miscible with PLLA and PCL, and that the dissolved PLLA‐CL in PLLA‐rich and PCL‐rich phases increased the compatibility between these two phases. © 2003 Society of Chemical Industry     

Enhanced crystallization of poly(L‐lactide‐co‐ε‐caprolactone) during storage at room temperature

Copolymer of L ‐lactide and ε‐caprolactone [P(LLA‐CL)] (50/50) was synthesized using stannous octoate and was stored at room temperature. The change in physical properties occurring during this storage at room temperature was investigated by differential scanning calorimetry (DSC), X‐ray diffractometry, polarizing optical microscopy, tensile and bending tests, and light absorbance measurements. It was concluded that the increase in mechanical properties and light absorbance during storage can be ascribed to gradual selective crystallization of the L ‐lactide sequence in P(LLA‐CL) at room temperature. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 947–953, 2000     

The effect of fabrication methods on the mechanical and thermal properties of poly(lactide‐co‐glycolide) scaffolds

The purpose of this research was to evaluate the effects of the fabrication method, poly(ethylene glycol) (PEG) molecular weight, and PEG concentration on the mechanical and thermal properties of blended poly (lactide‐co‐glycolide) (PLGA)/PEG scaffolds. The manufacturing process was the dominant factor. The tested fabrication processes were compression, heat molding, and solvent casting/vacuum drying. The scaffolds produced by compression were strong and brittle with mechanical properties [compressive modulus (E) ～ 400 N/mm²] comparable to those of trabecular bone. The heat‐molded scaffolds were weaker and more ductile (E ～ 45 N/mm²) than the compressed scaffolds, so they were more applicable to non‐load‐bearing applications. The vacuum‐dried scaffolds completely lacked compressive strength (E ～ 5 N/mm²) and were considered unsuitable for scaffolding applications. The miscibilities of the blends were also affected by the processing method and were evaluated on the basis of the melting‐point depression of crystalline PEG. The miscibility of PLGA in PEG was greatest with vacuum drying (6–13%), followed by heat molding (0.4–1.5%) and then compression (0.2–0.8%). The application of heat and solvent to the blend successfully altered the miscibility of the two polymers. Overall, this study demonstrates the ability to fabricate scaffolds with distinct thermal and mechanical characteristics by the manipulation of the fabrication method. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 944–949, 2007     

Thermogravimetric analysis of poly(3‐hydroxybutyrate) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)

The thermal degradation of poly(3‐hydroxybutyrate) (PHB) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) [P(HB‐HV)] was studied using thermogravimetry (TG). In the thermal degradation of PHB, the temperature at the onset of weight loss (T_o) was derived by T_o = 0.97B + 259, where B represents the heating rate (°C/min). The temperature at which the weight loss rate was maximum (T_p) was T_p = 1.07B + 273, and the final temperature (T_f) at which degradation was completed was T_f = 1.10B + 280. The percentage of the weight loss at temperature T_p (C_p) was 69 ± 1% whereas the percentage of the weight loss at temperature T_f (C_f) was 96 ± 1%. In the thermal degradation of P(HB‐HV) (7:3), T_o = 0.98B + 262, T_p = 1.00B + 278, and T_f = 1.12B + 285. The values of C_p and C_f were 62 ± 7 and 93 ± 1%, respectively. The derivative thermogravimetric (DTG) curves of PHB confirmed only one weight loss step change because the polymer mainly consisted of the HB monomer only. The DTG curves of P(HB‐HV), however, suggested multiple weight loss step changes; this was probably due to the different evaporation rates of the two monomers. The incorporation of 10 and 30 mol % of the HV component into the polyester increased the various thermal temperatures (T_o, T_p, andT_f) by 7–12°C (measured at B = 20°C/min). © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2237–2244, 2001     

Melt characteristics,mechanical, and thermal properties of blown film from modified blends of poly(butylene adipate‐co‐terephthalate) and poly(lactide)

Blown films from poly(butylene adipate‐co‐terephthalate) and poly(lactide) (PLA) blends were investigated. The blends were prepared in a twin‐screw extruder, in the presence of small amounts of dicumyl peroxide (DCP). The influence of DCP concentration on film blowing, rheological, mechanical, and thermal properties of the blends is reported in this article. Rheological results showed a marked increase in polymer melt strength and elasticity with the addition of DCP. As a consequence, the film homogeneity and the stability of the bubble were improved. The modified blend films, compared with the unmodified blend, showed an improvement in tensile strength and modulus with a slight loss in elongation. Fourier transform infrared and gel results revealed that chain scission and branching were more significant than crosslinking when the DCP loadings in the blends were not higher than 0.7%. A reduction in melt temperatures of PLA was observed due to difficulty in chain crystallization. The concentrations of DCP strongly affected the melting temperatures but had an insignificant effect on the decomposition behavior of the blends. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011