The physical and mechanical properties of beta‐nucleated polypropylene/montmorillonite nanocomposites

Polypropylene (PP) and polypropylene/polypropylene‐g‐maleic anhydride/ organomontmorillonite (PP/PP‐g‐MA/OMMT) nanocomposites were modified with 0.05 to 0.3% (w/w) of the aryl amide β‐nucleator to promote the formation of hexagonal crystal modification (β‐phase) during melt crystallization. The nonisothermal crystallization behavior of PP, PP/PP‐g‐MA/OMMT and β‐nucleated PP/PP‐g‐MA/OMMT nanocomposites were studied by means of differential scanning calorimetry. Structure‐property relationships of the PP nanocomposites prepared by melt compounding were mainly focused on the effect and quantity of the aryl amide nucleator. The morphological observations, obtained from scanning electron microscopy, transmission electron microscopy and X‐ray diffraction analyses are presented in conjunction with the thermal, rheological, and mechanical properties of these nanocomposites. Chemical interactions in the nanocomposites were observed by FT‐IR. It was found that the β‐crystal modification affected the thermal and mechanical properties of PP and PP/PP‐g‐MA/OMMT nanocomposites, while the PP/PP‐g‐MA/OMMT nanocomposites of the study gained both a higher impact strength (50%) and flexural modulus (30%) compared to that of the neat PP. β‐nucleation of the PP/PP‐g‐MA/OMMT nanocomposites provided a slight reduction in density and some 207% improvement in the very low tensile elongation at break at 92% beta nucleation. The crystallization peak temperature (T_cp) of the PP/PP‐g‐MA/OMMT nanocomposite was slightly higher (116°C) than the neat PP (113°C), whereas the β‐nucleation increased the crystallization temperature of the PP/PP‐g‐MA/OMMT/aryl amide to 128°C, which is of great advantage in a commercial‐scale mold processing of the nanocomposites with the resulting lower cycle times. The beta nucleation of PP nanocomposites can thus be optimized to obtain a better balance between thermal and mechanical properties. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Crystallization behavior of poly(p‐dioxanone)‐PU/montmorillonite nanocomposites prepared by chain‐extending reaction

Organo‐modified montmorillonites and poly(p‐dioxanone) (PPDO) diol prepolymers were used to prepare Poly(p‐dioxanone)‐PU/organic montmorillonite (PPDO‐PU/OMMT) nanocomposites by chain‐extending reaction. The crystallization behavior and spherulitic morphology of PPDO‐PU/OMMT nanocomposites were investigated by WXRD, differential scanning calorimetry, and polarized optical microscopy. The results show that the regularity of the chain structure plays a dominant role during the crystallization process rather than that of OMMT content and its dispersion status in PPDO matrix. With similar molecular weight and same OMMT content, PPDO‐PU/OMMT nanocomposite, which derived from lower molecular weight PPDO prepolymer, exhibits lower crystallization rate, melting point, and crystallinity. The influence of the clay content on the crystallization behavior highly depends on its dispersing state. The nucleating effect of OMMT can be only observed at high loading percentage. For the nanocomposites with low clay loading percentage, the retarding effect of exfoliated platelets on the chain‐ordering into crystal lamellae became the key factor. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Structure and properties of polypropylene/clay nanocomposites compatibilized by solid‐phase grafted polypropylene

Polypropylene/organic‐montmorillonite (PP/OMMT) nanocomposites were prepared via a solid‐phase PP graft (TMPP) with a higher grafting level as the compatibilizer. The effects of the compatibilizer on the structure and properties of PP/OMMT nanocomposites were investigated. The structure of the nanocomposites were characterized by X‐ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The results showed that when the weight ratio of TMPP and OMMT is greater than 1:1, the OMMT can be dispersed in PP matrix uniformly at the nanoscale. The mechanical properties of the nanocomposites reached a maximum when the weight ratio of TMPP and OMMT is 1:1, although more uniform dispersion was achieved at a higher content of TMPP. The mechanical properties of the nanocomposites decrease with the content of TMPP. The crystallization behavior, dynamic rheological property, and thermal stability of the nanocomposites were investigated by differential scanning calorimetry (DSC), dynamic rheological analysis, and thermal gravimetric analysis (TGA), respectively. Due to the synergistic effects of TMPP and OMMT on the crystallization of PP, the crystallization peak temperature of the nanocomposites increased remarkably compared with that of the neat PP. TMPP shows β‐phase nucleating ability and OMMT promotes the development of β‐phase crystallite. The nanocomposites show restricted melt flow and enhanced temperature sensitivity compared with the neat PP. The thermal stability of the nanocomposites is obviously improved compared with that of the neat PP. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers.     

Thermal,mechanical and morphological properties of surface‐modified montmorillonite‐reinforced Viton rubber nanocomposites

Thermal, mechanical and morphological properties of surface‐modified montmorillonite (OMMT)‐reinforced Viton rubber nanocomposites were studied. The surface of montmorillonite was modified with a column chromatography technique using quaternary long‐chain ammonium salt as an intercalant, which resulted in uniform exchange of ions between montmorillonite and the ion‐exchange resin, and increased the d‐spacing to 31.5 Å. This improved d‐spacing was due to the use of an ion‐exchange column of sufficient length (35 cm) and diameter (5 cm) with maximum retention time for exchange of ions. The Viton nanocomposites reinforced with OMMT (3–12 wt%) were prepared using a two‐roll mill and moulded in a compression moulding machine. Tensile strength increased 3.17 times and elongation at break from 500 to 600% for 9 wt% loading of OMMT in comparison to pristine Viton rubber. Thermogravimetric analysis revealed that the presence of OMMT greatly improved the thermal stability. This improvement in properties with increasing OMMT loading was due to insertion of rubber chains between the OMMT plates with good wetting ability. Overall, at an optimum OMMT loading of 9 wt%, the properties of the Viton rubber nanocomposites improved, and subsequently worsened at 12 wt% due to agglomeration of OMMT as revealed by scanning electron microscopy and atomic force microscopy images. © 2013 Society of Chemical Industry     

Effect of polymer matrix/montmorillonite compatibility on morphology and melt rheology of polypropylene nanocomposites

In this study, Ca²⁺‐montmorillonite (Ca²⁺‐MMT) and organo‐montmorillonite (OMMT) were modified by three compatibilizers with different degrees of polarity [poly(ethylene glycol) (PEG), alkyl‐PEG, and polypropylene (PP)‐g‐PEG]. PP/MMT nanocomposites were prepared by melt blending and characterized using X‐ray diffraction and transmission electron microscopy. The results showed the degree of dispersion of OMMT in the PP/PP‐g‐PEG/OMMT (PMOM) nanocomposite was considerably higher than those in the PP/PEG/OMMT and PP/alkyl‐PEG/OMMT nanocomposites, which indicated that the dispersion was relative to the compatibility between modified OMMT and PP matrix. Linear viscoelasticity of PP/MMT nanocomposites in melt states was investigated by small amplitude dynamic rheology measurements. With the addition of the modified MMT, the shear viscosities and storage modulus of all the PP/MMT nanocomposites decreased. It can be attributed to the plasticization effect of PEG segments in the three modifiers. This rheological behavior was different from most surfactant modified MMT nanocomposites which typically showed an increase in dynamic modulus and viscosity relative to the polymer matrix. The unusual rheological observations were explained in terms of the compatibility between the polymer matrix and MMT. In addition, the mechanical properties of PP/MMT nanocomposites were improved. A simultaneous increase in the tensile strength and toughness was observed in PP/PMOM nanocomposites. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

New toughened polypropylene/organophilic montmorillonite nanocomposites

A new toughened polypropylene (PP)/organophilic montmorillonite (OMMT) nanocomposite was obtained by melt intercalation extrusion in a twin‐screw extruder without any compatibilizer. The nanocomposites were characterized by transmission electron microscopy (TEM) observation, melt flow rate (MFR) testing, mechanical properties measurement, melting and crystallization behaviors, and thermal stability determination. TEM images revealed the existence of intercalated OMMT layers dispersed throughout the PP matrix. A clear reduction in MFR was observed as the OMMT content increased. The yield strength, elongation at yield, and initial modulus of the PP/OMMT nanocomposites increased slightly as the result of the reinforcement of the OMMT nanofiller. The ultimate value of notched impact strength of the nanocomposites was over twofold that of neat PP after incorporation with 4 wt % OMMT; meanwhile, the heat deflection temperature values showed that the thermal stability increased a little. This is a new approach for preparation for the production of a toughened PP material with a high thermal stability and rigidity. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of functionalized SWCNTs on microstructure of PP‐g‐MA/OMMT/f‐SWCNTs nanocomposite

The aim of this work was to study the effect of functionalized single‐walled carbon nanotubes (f‐SWCNTs) on the microstructure of PP‐g‐MA/organic modified montmorillonite (OMMT)/f‐SWCNTs ternary nanocomposite. Pristine SWCNTs were chemically modified by maleic anhydride to improve the interaction between PP‐g‐MA and nanotubes. The dispersion states of OMMT in the different nanocomposites were investigated by wide angle X‐ray diffraction. The morphologies of the nanocomposites were characterized by scanning electron microscopy. Crystallization behaviors of nanocomposites were studied through differential scanning calorimetry and polarizing optical microscopy. Different than the PP‐g‐MA/OMMT binary nanocomposite, in which the OMMT is mainly in an exfoliated state, the ternary PP‐g‐MA/OMMT/f‐SWCNTs nanocomposite exhibits mostly intercalated OMMT. Furthermore, in the ternary nanocomposite, the crystallization of polymer is mainly induced by f‐SWCNTs rather than by OMMT. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Exfoliation targeted toughness enhancement in polypropylene‐blend‐ montmorillonite nanocomposites

BACKGROUND: Both exfoliated and toughened polypropylene‐blend‐montmorillonite (PP/MMT) nanocomposites were prepared by melt extrusion in a twin‐screw extruder. Special attention was paid to the enhancement of clay exfoliation and toughness properties of PP by the introduction of a rubber in the form of compatibilizer toughener: ethylene propylene diene‐based rubber grafted with maleic anhydride (EPDM‐g‐MA). RESULTS: The resultant nanocomposites were characterized using X‐ray diffraction, atomic force microscopy, scanning electron microscopy, thermogravimetric analysis, dynamic mechanical analysis and Izod impact testing methods. It was found that the desired exfoliated nanocomposite structure could be achieved for all compatibilizer to organoclay ratios as well as clay loadings. Moreover, a mechanism involving a decreased size of rubber domains surrounded with nanolayers as well as exfoliation of the nanolayers in the PP matrix was found to be responsible for a dramatic increase in impact resistance of the nanocomposites. CONCLUSION: Improved thermal and dynamic mechanical properties of the resultant nanocomposites promise to open the way for highly toughened super PPs via nanocomposite assemblies even with very low degrees of loading. Copyright © 2008 Society of Chemical Industry     

Polypropylene/montmorillonite composites and their application in hybrid fiber preparation by melt‐spinning

Polypropylene (PP)/organomontmorillonite (OMMT) nanocomposites have been successfully prepared by melt intercalation by using the conventional method of twin‐screw extrusion and subsequently submitted for melt‐spinning. The structure and properties of the PP/clay nanocomposites and hybrid fibers were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X‐ray diffraction (XRD), differential scanning calorimetry (DSC), and crystallization dynamics, etc. The organoclay layers were found to disperse in the PP resin at the nanometer level. The nanoscaled OMMT layers, dispersed in the PP matrix, actually played the role of heterogeneous nuclei species in the process of PP crystallization and increased the nucleation speed of the composites, hereby leading to the increase of crystallization rate of the as‐spun fiber. Meanwhile, it was found that the crystallinity of PP/OMMT hybrid fibers is much higher than that of pure PP fiber at the same draw ratios, whereas the orientation of PP/OMMT hybrid fibers is much lower than that of pure PP fiber at the same draw ratios. Because of the effective intercalation of OMMT into PP matrix, the nanocomposites have good spinnability, and the moisture absorption of the final PP fiber is improved. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 552–558, 2004     

Polypropylene nanocomposites prepared with natural and ODTABr‐modified montmorillonite

In this study, the main goal is to obtain montmorillonite nanocomposites of polypropylene (PP). To achieve this goal, a two‐phase study was performed. In the first part of the work, organomodified clay (OMMT) was synthesized and characterized. Octadecyltrimethylammonium bromide (ODTABr) cationic surfactant was added to the clay (Na‐activated montmorillonite, MMT) dispersions in different concentrations in the range of 5 × 10^?5–1 × 10^?2 mol/L. Rheologic, electrokinetic, and spectral analyses indicated that ODTABr has interacted with MMT at optimum conditions when the concentration was 1 × 10^?2 mol/L. In the second part, modified (OMMT) and unmodified (MMT) montmorillonite were used to obtain PP nanocomposites (OMMT/PP and MMT/PP, respectively). The nanocomposites were prepared by melt intercalation where the montmorillonite contents were 1 or 5% (w/w) for each case. The thermal analyses showed that the thermal properties of OMMT/PP nanocomposites were better than MMT/PP, and both of them were also better than pure polymer. Increase in the concentration of MMT (or OMMT) decreased the thermal resistance. Based on the IR absorption intensity changes of regularity and conformational bands, it is found that the content of the helical structure of macromolecular chains has increased with increasing concentrations of both MMT and OMMT in the nanocomposites. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Water absorption and hygrothermal aging study on organomontmorillonite reinforced polyamide 6/polypropylene nanocomposites

The water absorption and hygrothermal aging behavior of organomontmorillonite (OMMT) reinforced polyamide 6/polypropylene (PA6/PP ratio = 70/30), with and without maleated PP (MAH‐g‐PP), was studied at three different temperatures (30, 60, and 90°C). The water absorption and hygrothermal aging response of the composites was studied and analyzed by tensile tests and morphology assessment (scanning electron microscopy and transmission electron microscopy), indicating the effect of the immersion temperature, OMMT, and MAH‐g‐PP compatibilizer. The mathematical treatment used in analyzing the data was the single free phase model of diffusion, which assumed Fickian diffusion and utilized Fick's second law of diffusion. The kinetics of water absorption of the PA6/PP nanocomposites conformed to Fickian law behavior, whereby the initial moisture absorption follows a linear relationship between the percentage gain at any time t and t^1/2 (the square root of time), followed by saturation. It was found that the equilibrium moisture content and the diffusion coefficient are dependent on the OMMT loading, MAH‐g‐PP concentration, and immersion temperatures. Both the tensile modulus and strength of the PA6/PP nanocomposites deteriorated after being exposed to hygrothermal aging. MAH‐g‐PP acted as a good compatibilizer for PA6/PP/OMMT nanocomposites, which was attributed to its higher retention ability in modulus and strength (in the wet and redried states), lower equilibrium moisture content, and reduced water diffusivity of the nanocomposites. Morphological sketches for both uncompatibilized and MAH‐g‐PP compatibilized PA6/PP/OMMT nanocomposites, toward water uptake are proposed. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 780–790, 2005     

Isothermal crystallization behavior of poly(L‐lactic acid)/organo‐montmorillonite nanocomposites

The isothermal crystallization behavior of poly(L ‐lactic acid)/organo‐montmorillonite nanocomposites (PLLA/OMMT) with different content of OMMT, using a kind of twice‐functionalized organoclay (TFC), prepared by melt intercalation process has been investigated by optical depolarizer. In isothermal crystallization from melt, the induction periods (t_i) and half times for overall PLLA crystallization (100°C ≤ T_c ≤ 120°C) were affected by the temperature and the content of TFC in nanocomposites. The kinetic of isothermal crystallization of PLLA/TFC nanocomposites was studied by Avrami theory. Also, polarized optical photomicrographs supplied a direct way to know the role of TFC in PLLA isothermal crystallization process. Wide angle X‐ray diffraction (WAXD) patterns showed the nanostructure of PLLA/TFC material, and the PLLA crystalline integrality was changed as the presence of TFC. Adding TFC led to the decrease of equilibrium melting point of nanocomposites, indicating that the layered structure of clay restricted the full formation of crystalline structure of polymer. The specific interaction between PLLA and TFC was characterized by the Flory‐Huggins interaction parameter (B), which was determined by the equilibrium melting point depression of nanocomposites. The final values of B showed that PLLA was more compatible with TFC than normal OMMT. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

Solid‐state graft polymerization of styrene in spherical polypropylene particles in the presence of montmorillonite

In this work, cetyltrimethyl ammonium bromide and methacryloyloxyethyhrimethyl ammonium chloride were used to prepare organophilic montmorillonite (O‐MMT). Then, polypropylene (PP)–clay nanocomposites were prepared by the in situ grafting polymerization of styrene (St)‐containing O‐MMT onto PP with tert‐butyl perbenzoate as an initiator in the solid state. Fourier transform infrared spectroscopy, gel permeation chromatography, transmission electron microscopy, and X‐ray diffraction were applied to study the structure of the layered silicate and modified PP. The surfaces of the composites and, thus, the distribution of the clay in the PP matrix were characterized by scanning electron microscopy. The rheology and mechanical properties were studied and are discussed. According to the characterization results, OMMT and St were already grafted onto the PP main chain. Also, the intercalated structure of montmorillonite could be stabilized, and a stable exfoliated structure could be attained. Namely, intercalated PP/OMMT nanocomposites were obtained. The rheological results clearly show that these PP/OMMT nanocomposites had long‐chain‐branched structures. The peroxide modification of PP had minor effects on the tensile and bending strengths of the modified PP; however, this modification resulted in a significant reduction in the impact strength. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Intercalation and exfoliation of talc by solid‐state shear compounding (S3C) using pan‐mill equipment

The intercalation and exfoliation of talc have been realized by solid‐state shear compounding (S³C) using pan‐mill equipment that can exert fairly strong shear forces and has multifunctions such as pulverizing, mixing, and activation on materials. The structural features of pan‐mill also show prospective in delaminating layered minerals. The morphology and structure of talc were investigated by using transmission electron microscopy (TEM) and X‐ray diffraction (XRD). The characteristic peaks of talc interlayer spacing disappeared in the XRD pattern of PP/talc composite prepared by S³C, however, still remained in the XRD pattern of PP/talc prepared by the conventional mixing method. TEM confirms the intercalated and exfoliated structure of talc, and the well dispersion of talc in the PP matrix after talc and PP were co‐milled. S³C is a new approach to prepare polymer/layered inorganic filler nanocomposite and has characteristics such as a simple process that needs neither organic ligands nor solvent. POLYM. ENG. SCI. 45:451–457, 2005. © 2005 Society of Plastics Engineers.     

Ultrasound assisted continuous‐mixing for the preparation of PP/SEBS/OMMT ternary nanocomposites

Polypropylene (PP)/polystyrene‐block‐poly(ethylene‐co‐butylenes)‐block‐polystyrene (SEBS)/organo‐montmorillonite (OMMT) nanocomposites of varying concentrations of maleic anhydride‐grafted polypropylene (PP‐g‐MA) were prepared by continuous mixing assisted by ultrasonic oscillation. The structure and morphology of nanocomposites were investigated by X‐ray diffraction (XRD), transmission electron microscopy, and scanning electron microscopy. It was found that both PP‐g‐MA and ultrasonic oscillation could enhance the intercalation and exfoliation of OMMT in PP matrix. Meanwhile, the formation of PP could be induced by ultrasonic irradiation at a power of more than 540 W. Rheological properties including complex viscosity, storage, and loss modulus of nanocomposites were increased after adding PP‐g‐MA or ultrasonic treatment. The results of mechanical properties showed that PP‐g‐MA could improve the tensile strength and tensile modulus of nanocomposites, but with the sacrifice of impact strength. This problem could be improved by ultrasound due to the reduced particle size of SEBS. However, the mechanical properties would be reduced by ultrasonic treatment with higher intensity due to the polymer degradation. Therefore, the synergistic effect of both compatibilizer and ultrasound should account for the balance between toughness and stiffness of PP/SEBS/OMMT ternary nanocomposites. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41202.     

Polypropylene/organically modified Sabah montmorillonite nanocomposites: Surface modification and nanocomposites characterization

The aim of the work is to extract, purify, and organically modify montmorillonite (MMT) of Lahad Datu, Sabah bentonite. The octadecylamine treated Sabah MMT (S‐OMMT) (2–8 wt%) was then melt blended with polypropylene (PP) and maleated polypropylene (PPgMAH) (10 wt%) via single screw nanomixer extruder followed by injection molding into test samples to examine the mechanical, thermal, and morphological properties of PP/S‐OMMT nanocomposites. Unmodified Sabah MMT (S‐MMT) and commercial grade MMT (Nanomer 1.30P) filled PP nanocomposites were also characterized for comparison purpose. X‐ray diffraction results showed that the interlayer spacing of S‐MMT increased after organic modification as Fourier transform infra‐red and elemental analysis evidenced the presence of octadecylamine. PP/S‐OMMT nanocomposites showed a better dispersion and strength compared to PP/Nanomer 1.30P nanocomposites due to its smaller MMT platelet size. differential scanning calorimetry and Thermogravimetry analysis revealed that the thermal stability and crystallinity of neat PP improved with the addition of all types of MMT. Dynamic mechanical analyzer showed that PP nanocomposites have higher storage modulus (E′) values than the neat PP over the whole temperature range. The new PP/S‐OMMT nanocomposites showed a comparable performance with PP/Nanomer 1.30P nanocomposites exhibiting promising future applications of S‐MMT in polymer/MMT nanocomposites. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

Synergistic effects of zinc oxide in montmorillonite flame‐retardant polystyrene nanocomposites

In this study, two‐dimensional organic montmorillonite (OMMT) and one‐dimensional needlelike ZnO were used as flame retardants of polystyrene (PS). Polystyrene/organic montmorillonite (PMT) and polystyrene/organic montmorillonite/zinc oxide nanocomposites (PMZs) with different weight ratios were prepared by melt intercalation. Information on the morphologies and structures of the PS nanocomposites was obtained with Fourier transform infrared spectroscopy, X‐ray diffraction, scanning electron microscopy, and transmission electron microscopy. The results indicate that a mixed exfoliated–intercalated structure was observed in the PMT and PMZs. Dynamic mechanical thermal analysis showed that both the storage modulus and glass‐transition temperature values of the PMT and PMZs were significantly improved compared with those of the neat PS. The mechanical property tests showed that the bending modulus values of both PM5 (PS/OMMT weight ratio = 95:5) and PMZs increased compared with that of pristine PS. PMZ1 (PS/OMMT/ZnO weight ratio = 94:5:1) provided no decrease in the tensile strength in comparison with PS. A synergistic effect was observed between OMMT and ZnO; this resulted in improvements in the flame retardancy and dynamic mechanical properties in the PMZs. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43047.     

Dynamic rheology and morphology of polylactide/organic montmorillonite nanocomposites

The effects of organic montmorillonite (OMMT) on the rheological behaviors and phase morphology of polylactide (PLA) were investigated. The rheological behaviors of nanocomposites showed mainly dependence on both temperature and OMMT content. At low OMMT loading (1 wt %), the complex viscosities showed a Newtonian plateau in low frequency region at low temperatures and converted to a shear‐thinning behaviors with increasing temperature. In comparison, at high OMMT loadings (above 5 wt %), strong shear‐thinning behaviors were observed in the full range of frequencies and temperatures. The results demonstrated rheology of PLA/OMMT is highly sensitive to the nanofillers filled materials. A pseudo‐solid‐like behavior at long scale time in the hybrids with OMMT loading was higher than 5 wt %, this response was related to the formation of a network structure across the polymer matrix due to strong interactions of PLA and OMMT that confined the relaxation process of the macromolecules. X‐ray diffraction and transmission electron microscopy indicated the nanocomposites at low OMMT loading were mainly exfoliated and intercalated nanocomposites were gradually formed with increasing OMMT loading. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Reinforcing effect and isothermal crystallization kinetics of poly(3‐hydroxybutyrate) nanocomposites blended with organically modified montmorillonite

Organically modified montmorillonite (OMMT) has been incorporated up to 7 wt% in poly(3‐hydroxybutyrate) (PHB) by melt compounding in a twin screw extruder. PHB nanocomposites reinforced with C93A showed significant increase in tensile and flexural modulus and impact strength comparatively. Wide angle X‐ray diffraction showed an increase in overall d‐spacing indicating intercalated structure. The intercalation morphology was further supported by transmission electron microscope images indicating formation of intercalated structure in case of PHB/OMMT and a mixture of Intercalated/exfoliated structure in case of PHB/TMI‐MMT nanocomposites. Thermogravimetric analyses indicate that the thermal stability of PHB/TMI‐MMT nanocomposites is higher among all other nanocomposites under investigation and virgin PHB. Differential scanning calorimetry (DSC) analysis of PHB nanocomposites shows marginal increase in glass transition temperature and decrease in crystallization temperature compared to virgin PHB. The isothermal crystallization kinetics of PHB/C93A nanocomposites was investigated by DSC in the temperature range of 100–120°C and the development of relative crystallinity with the crystallization time was analyzed by Avrami equation. POLYM. COMPOS., 35:999–1012, 2014. © 2013 Society of Plastics Engineers     

Preparation and characterization of exfoliated organic montmorillonite/poly(3,4‐ethyldioxythiophene) nanocomposites

Montmorillonite, organically modified by octadecylammine salt, has been adopted to successfully fabricate the exfoliated organic montmorillonite/poly(3,4‐ethyldioxythiophene) (OMMT/PEDOT) nanocomposites by in situ polymerization in aqueous media. Hydrochloric acid, 1,5‐naphthalenedisulfonic acid, and sodium benzenesulphonate have been employed to activate the polymerization of 3,4‐ethyldioxythiophene by offering active sites on the layers of montmorillonite. The resulting exfoliated nanocomposites have been characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, transmission electron microscopy, X‐ray diffraction, thermogravimetric analysis, and electrical conductivity measurement and showed controllable conductivity in the range of 10^?7 to 10^?2 S/cm and improved thermal stability compared with pure PEDOT. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009