Isothermal crystallization behavior of polyamide 6,6/multiwalled carbon nanotube nanocomposites

The good dispersion of functionalized multiwalled carbon nanotube (f‐MWCNT) in polyamide 6,6 (PA 6,6) matrix was prepared by solution mixing techniques. The crystalline structure and crystallization behaviors of PA 6,6 and PA 6,6/f‐MWCNT nanocomposites were studied by X‐ray diffraction (XRD), differential scanning calorimetry (DSC), and polarized optical microscopy (POM) analysis. DSC isothermal results revealed that the overall isothermal crystallization rates of PA 6,6 increased as well as the activation energy of PA 6,6 extensively decreased by adding f‐MWCNT into PA 6,6, suggesting that the addition of f‐MWCNT probably induces the heterogeneous nucleation. The effect of f‐MWCNT on the chain arrangement for the crystallization of PA 6,6/f‐MWCNT nanocomposites was also discussed. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Isothermal crystallization behavior of polyoxymethylene with and without nucleating agents

Nucleation effects of two silicate nucleating agents, attapulgite and diatomite, on the crystallization of polyoxymethylene (POM), were studied by means of differential scanning calorimetry and polarized optical microscopy. The crystallization kinetics of POM with and without nucleating agents was analyzed by means of two isothermal crystallization kinetic equations through the crystallization thermograms. Compared with virgin POM, POM with nucleating agents of attapulgite and diatomite decreased the spherulitic size of POM and interfacial free energies per unit area perpendicular σ_e. The crystallization growth rate was accelerated because of nucleating agents as well. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 304–310, 2001     

High Efficiency Nucleating Agents of Polyoxymethylene

In this research, the effects of different kinds of nucleating agents on the crystallization and mechanical properties of polyoxymethylene (POM) were studied, including inorganic, organic, and polymer nucleating agents and their compounds. These properties showed that nanoCaCO₃, sorbitol derivative TMB-5, polyamide PA-4, and compound C-1/polyamide (PA)-4 can make spherulites of POM finer and more perfect, and effectively improve its notched impact toughness, in which the compound C-1/PA-4 displayed more remarkable nucleation effect. The study on the nonisothermal crystallization of POM showed that the crystallization temperature and crystallization growth rate of POM increased when C-1/PA-4 was added. The isothermal crystallization kinetics were also analyzed by the Avrami equation. The addition of C-1/PA-4 can increase the values of the Avrami exponent (n) and crystallization rate constant (k), and reduce the half-time of isothermal crystallization, t_1/2, and the time corresponding to the maximum rate of crystallization, t_P, indicating its remarkable nucleating effect on POM.     

Isothermal crystallization kinetics and melting behavior of in situ compatibilized polyamide 6/Polyethylene-octene blends

We developed in situ compatibilization technology to improve the compatibility between polyamide 6 (PA 6) and polyethylene-octene (POE). In the present work, we investigated the isothermal crystallization and melting behavior of PA 6/POE blends using differential scanning calorimetry (DSC). All specimens exhibited double melting peaks at lower temperature and single melting peaks at higher temperature. The Avrami exponent and equilibrium melting temperature were obtained by analysis of DSC experimental data using the Avrami equation and Hoffman-Weeks theory, respectively. It has demonstrated that the crystallization model of PA 6 for all specimens might be a mixture with two-dimensional, circular, three-dimensional growth with thermal nucleation. We further calculated the nucleation parameter (K _g ) from the obtained crystallization kinetics data using Lauritzen-Hoffmann equation. It was found that the K _g values of the compatibilized PA 6 were lower than that of pure PA 6 whereas increased with the increase of POE content, which was related to the better dispersion of POE and the interaction between PA 6 and the in situ formed POE-g-MAH. Additionally, the spherulite morphology was observed by polarized optical microscopy (POM).     

Influence of pre-shearing on the crystallization of an impact-resistant polypropylene copolymer

Impact-resistant polypropylene copolymer (IPC) samples with various pre-shear histories were prepared by a Brabender Rheometer. The influence of pre-shearing on crystallization of IPC, including isothermal and nonisothermal crystallization behaviors was investigated by differential scanning calorimetry (DSC) and polarized optical microscopy (POM). The results of nonisothermal crystallization showed that compared with as-received IPC, the temperatures referred to the peak of crystallization exotherm, T_p, were prominently elevated for pre-sheared IPC. In isothermal crystallization experiment, combining Avrami Method and Hoffman-Lauritzen Model, it was found that the half-time of crystallization (t_1/2) of pre-sheared IPC was greatly shortened and the calculated fold surface free energy (σ_e) within the isothermal temperatures investigated showed a large reduction. Morphological development during isothermal crystallization observed by POM clearly confirmed that the enhancement in crystallization is mainly due to the fast formation of nuclei during crystallization. Besides, using successive self-nucleation and annealing (SSA) thermal fractionation technique, changes in chain structures induced by pre-shearing were obtained. The relaxation behavior of pre-sheared IPC was also evaluated and it was found that the shear-induced enhancement in crystallization could be relaxed to various extents under annealing conditions.     

Crystallization characteristics of polyoxymethylene with attapulgite as nucleating agent

The nucleation of polyoxymethylene (POM) crystallization using attapulgite was studied using differential scanning calorimetry, polarized light microscopy, wideangle X‐ray diffration and mechanical testing. Two isothermal crystallization kinetic equations were employed to describe the crystallization of virgin POM and POM containing attapulgite as a nucleating agent. The addition of attapulgite decreased the spherulitic size of POM, and interfacial free energies per unit area perpendicular to the molecular chain direction ρ_e, accelerated the crystallization growth rate and enhanced the impact toughness of POM, but no change occurred for the hexagonal system of POM. The addition of attapulgite up to its saturation concentration in POM increased the number of effective nuclei by three orders of magnitude. A high concentration of attapulgite caused agglomeration of the agent and lowered the number of effective nuclei.     

Studies on novel composites of polyoxymethylene/ polyamide 6

A series of new composite of polyoxymethylene/polyamide 6 (POM/PA 6) were synthesized by using ε‐caprolactam as a reactive solvent with POM soluble in it. Incorporating a small content of POM (1–4 wt %) into PA 6 led to a great improvement of impact resistance POM/PA 6. The effects of POM content on the mechanical, morphological, and thermal properties of the composites were investigated. Incorporating minor POM (1 wt %), disposed in finely dispersed level (about 1 μm), into PA 6 matrix can greatly reduce the crystallization rate and crystallinity of PA 6. Scanning electron microscopy measurements indicated that much microfibers with aspect ratio about 10 appeared with the addition of 3 wt % POM because of the change of phase separation mechanisms. As a result, with a small content of PA 66 (1–4 wt %) incorporated, the impact strength and elongation of POM/PA 6 were improved markedly, with retention of good tensile strength. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 335–339, 2006     

Influence of a synthetic ureido nucleating agent on crystallization behavior and mechanical properties of polyamide 6

A synthetic ureido mixture prepared from the reaction of 4,4′‐diphenylmethane disocynanate (MDI) and cyclohexylamine without using any harmful organic solvents, has been used as a nucleating agent (PNA) for polyamide 6 (PA6). The effect of PNA on the crystallization and mechanical properties of PA6 has been studied by means of differential scanning calorimetry (DSC), polarized optical microscopy (POM), tensile test, melt flow index (MFI), and X‐ray diffraction (XRD). The results show that PNA is an effective nucleation agent for PA6. PNA affects the nucleation mechanism of PA6, and substantially accelerates the crystallization rate of PA6 and gives rise to smaller crystal size. In comparison with PA6, the crystallization temperature (T_c) of PA6/PNA (100/0.5) increases 21.3°C and the degree of sub‐cooling (ΔT_c) decreases 23.7°C. Furthermore, because of the heterogeneous nucleation induced by PNA, the spherulites of PA6 become even and tiny based on POM observation. Polymorph transform has been obtained from XRD analysis. The virgin PA6 is free of γ‐phase crystals, presented as α‐phase crystals in this study, but γ‐phase crystal appears after the introduction of PNA. The mechanical and thermal properties of PA6 are obviously improved by the addition of PNA. POLYM. ENG. SCI., 55:2011–2017, 2015. © 2015 Society of Plastics Engineers     

Crystallization and thermal behavior of microcellular injection‐molded polyamide‐6 nanocomposites

This article presents the effects of nanoclay and supercritical nitrogen on the crystallization and thermal behavior of microcellular injection‐molded polyamide‐6 (PA6) nanocomposites with 5 and 7.5 wt% nanoclay. Differential scanning calorimetry (DSC), X‐ray diffractometry (XRD), and polarized optical microscopy (POM) were used to characterize the thermal behavior and crystalline structure. The isothermal and nonisothermal crystallization kinetics of neat resin and its corresponding nanocomposite samples were analyzed using the Avrami and Ozawa equations, respectively. The activation energies determined using the Arrhenius equation for isothermal crystallization and the Kissinger equation for nonisothermal crystallization were comparable. The specimen thickness had a significant influence on the nonisothermal crystallization especially at high scanning rates. Nanocomposites with an optimal amount of nanoclay possessed the highest crystallization rate and a higher level of nucleation activity. The nanoclay increased the magnitude of the activation energy but decreased the overall crystallinity. The dissolved SCF did not alter the crystalline structure significantly. In contrast with conventionally injection‐molded solid counterparts, microcellular neat resin parts and microcellular nanocomposite parts were found to have lower crystallinity in the core and higher crystallinity near the skin. POLYM. ENG. SCI., 46:904–918, 2006. © 2006 Society of Plastics Engineers     

Effect of small amount of ultra high molecular weight component on the crystallization behaviors of bimodal high density polyethylene

In order to clarify the effect of high molecular weight component on the crystallization of bimodal high density polyethylene (HDPE), a commercial PE-100 pipe resin was blended with small loading of ultra high molecular weight polyethylene (UHMWPE). The isothermal crystallization kinetics and crystal morphology of HDPE/UHMWPE composites were studied by differential scanning calorimetry (DSC) and polarized optical microscopy (POM), respectively. The presence of UHMWPE results in elevated initial crystallization temperature of HDPE and an accelerating effect on isothermal crystallization. Analysis of growth rate using Lauritzen-Hoffman model shows that the fold surface free energy (σ_e) of polymer chains in HDPE/UHMWPE composites was lower than that in neat HDPE. Morphological development during isothermal crystallization shows that UHMWPE can obviously promote the nucleation rate of HDPE. It should be reasonable to conclude that UHMWPE appeared as an effective nucleating agent in HDPE matrix. Rheological measurements were also performed and it is shown that HDPE/UHMWPE composites are easy to process and own higher melt viscosity at low shear rate. Combining with their faster solidification, gravity-induced sag in practical pipe production is expected to be effectively avoided.     

Crystal morphology and crystallization kinetics of polyamide‐11/clay nanocomposites

Polyamide‐11 (PA11)/clay nanocomposites were prepared by in situ intercalative polymerization. The crystal morphology and crystallization kinetics of these nanocomposites were investigated via polarized light microscopy (PLM), small‐angle laser scattering (SALS) and differential scanning calorimetry (DSC). PA‐11 can crystallize into well‐formed spherulites, while only very tiny crystallites were observed by PLM and SALS for the nanocomposites. Both isothermal and non‐isothermal crystallization methods were employed to investigate the crystallization kinetics by DSC. Both techniques showed an increased crystallization rate with the addition of clay. However, the Avrami exponent decreased with the addition of clay in isothermal crystallization but showed a wide range of values depending on the cooling rate in the non‐isothermal crystallization. The changes in crystal morphology and crystallization kinetics can be understood as being due to the ‘supernucleating’ effect of the nanodispersed clay layers. Copyright © 2004 Society of Chemical Industry     

Crystallization behavior and morphology of double crystalline poly(butylene succinate)-poly(ethylene glycol) multiblock copolymers

The crystallization kinetics, morphology and crystal structure of biodegradable double crystalline poly(butylene succinate)-poly(ethylene glycol) (PBS-PEG) multiblock copolymers (PBSEGs) were studied with different composition and segment chain length by differential scanning calorimetry (DSC), polarized optical microscopy (POM) and wide-angle X-ray diffraction (WAXD). The isothermal crystallization kinetics results show that the overall crystallization rate and the equilibrium melting point of PBS increase with the increasing PBS fraction and the segment chain length (L_PBS); on the other hand, the higher content or longer PEG segment within PBSEGs possesses larger crystallization rate of PEG chains. The nucleation mechanisms are demonstrated to be instantaneous 3D and 2D aggregates for PBS and PEG segments within PBSEGs, respectively (except for PBSEG_2K?50, 2D and 3D aggregates for PBS and PEG segments, respectively). POM observations indicate that the PBS within PBSEG multiblock copolymers presents banded spherulites in the investigated temperature range. After quenched to lower temperature, PBS templates the morphology for PEG crystallization, and PEG crystallization just changes the magnitude of birefringence (lighting the spherulites) but not influences the superstructure. Finally, WAXD measurements determine that the crystal structure is not changed with the compositions.     

Polyamide-based composite membranes: Part 2. Interaction, crystallization and morphology

In this work, the interaction, crystallization and morphology of membranes derived from polyamides/poly (vinylalcohol) (PA/PVA, PA: PA66, PA69, PA610 and PA612) blend materials are studied at various weight fractions and various crystallization temperatures. The experimental work includes differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), polarized optical microscopy (POM) and scanning clectron microscopy (SEM). The equilibrium melting temperatures of polyamides in the blends are obtained using Hoffman-Weeks plots, and the interaction parameters are calculated using the Nishi-Wang equation, which is based on the Flory-Huggins theory. The values of the Flory-Huggins interaction parameters χ₁₂ are negative. Significant upward shifts of ν_NH are observed with increasing volume fraction of PVA. The morphology of membranes is impressively complex, diverse, and irregular. All compositions that show nodular morphology are in the μm-scale and the size of the nodules increases with increasing PA6 content. Large void cavities are observed in the substructure for the lower polymer concentrations.     

原位增容PA6/PE-HD共混物的等温结晶动力学研究

采用差示扫描量热仪研究了原位增容聚酰胺6/高密度聚乙烯（PA6/PE-HD）共混物的等温结晶行为,采用Avrami方程分析了纯PA6和PA6/PE-HD共混物的等温结晶动力学,并通过Hoffman-Weeks方法计算出了共混物的平衡熔点。结果表明,二者的Avrami指数介于2.19~3.70之间,表明PA6晶体的生长方式为二维盘状生长和三维球晶生长并存,PE-HD的加入并没有影响PA6晶体的生长方式。偏光显微镜分析表明,纯PA6能够生成球晶,但加入PE-HD后,球晶尺寸明显变小,说明PE-HD的加入起到了异相成核的作用,加快了PA6的结晶过程。     

Crystallization behavior and isothermal crystallization kinetics of PLLA blended with ionic liquid, 1‐butyl‐3‐methylimidazolium dibutylphosphate

The crystallization behavior and isothermal crystallization kinetics of neat poly(l ‐lactic acid) (PLLA) and PLLA blended with ionic liquid (IL), 1‐butyl‐3‐methylimidazolium dibutylphosphate, were researched by differential scanning calorimetry (DSC), polarizing optical microscopy (POM), and wide angle X‐ray diffraction (WXRD). Similar to the non‐isothermal crystallization behavior of neat PLLA, when PLLA melt was cooled from 200 to 20°C at a cooling rate of 10°C min^?1, no crystallization peak was detected yet with the incorporation of IL. However, the glass transition temperature and cold crystallization temperature of PLLA gradually decreased with the increase of IL content. It can be attributed to the significant plasticizing effect of IL, which improved the chain mobility and cold crystallization ability of PLLA. Isothermal crystallization kinetics was also analyzed by DSC and described by Avrami equation. For neat PLLA and IL/PLLA blends, the Avrami exponent n was almost in the range of 2.5–3.0. It is found that t_1/2 reduced largely, and the crystallization rate constant k increased exponentially with the incorporation of IL. These results show that the IL could accelerate the overall crystallization rate of PLLA due to its plasticizing effect. In addition, the dependences of crystallization rate on crystallization temperature and IL content were discussed in detail according to the results obtained by DSC and POM measurements. It was verified by WXRD that the addition of IL could not change the crystal structure of PLLA matrix. All samples isothermally crystallized at 100°C formed the α‐form crystal. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41308.     

Crystallization Behaviors of amino-terminated polyurethane (ATPU)-grafted polypropylene

Summary A melt-grafting approach was employed to prepare a novel functional polypropylene(FPP)—amino-terminated polyurethane grafted polypropylene (PP-g-ATPU). The crystallization behaviors of PP and PP/FPP blends were characterized using differential scanning calorimetry (DSC), wide angle X-ray scattering (WAXS) and polarized optical microscopy (POM). The effects of FPP composition on crystallization behavior, crystal transformation, and morphology of PP/FPP crystalline were investigated. The results showed that at a low dosage (<2.0 wt%) ATPU acted as a heterogeneous nucleation agent during the crystallization of PP/FPP blends. However, when the content of ATPU reached 2.0 wt% or higher, ATPU deteriorated the crystallization of PP or PP/FPP blends. The crystallite size decreased and the number of crystallites increased as the ATPU content increased. The Avrami analysis was adopted to describe the isothermal crystallization process. The difference in the exponent n between PP and PP/FPP suggested that the isothermal crystallization kinetics of PP/FPP blends followed a three-dimensional growth via heterogeneous nucleation. In terms of the half-time of the crystallization, t_1/2, the crystallization rate of functional PP blends was faster than that of PP homopolymer at a given crystallization temperature.     

Synergistic thermal stabilization effect of polyamide/melamine on polyoxymethylene

The synergistic thermal stabilization effect of polyamide (PA) and melamine (MA) on polyoxymethylene (POM) was studied by isothermal weight loss analysis and nonisothermal thermogravimetric analysis, which showed that the complex stabilizer PA/MA was more efficient than the single‐use formaldehyde absorbents MA or PA in improving the thermal stability of POM. The nonisothermal degradation kinetics study further demonstrated the synergistic thermal stabilization effect of PA/MA on POM. The mechanical property investigation showed that the addition of a proper amount of PA or the proper reduction of MA content improved the impact strength of POM. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 2387–2391, 2005     

Studies on the isothermal crystallization kinetics and crystal morphology of PTT/SGF composites

The kinetics of isothermal crystallization and crystal morphology of poly(trimethylene terephthalate)/short glass fibers (PTT/SGF) composites were investigated by using differential scanning calorimetry (DSC) and polarized optical microscopy (POM). DSC data was analyzed by the Avrami equation and Hoffman‐Lauritzen theory. The results show that SGF plays a role as the nucleating agent, which largely accelerates the crystallization rate of PTT. SGF below 20% will increase the crystallinity of the composites but 30% SGF will decrease the crystallinity, which is also verified by the crystallinity results calculated from the wide‐angle x‐ray diffraction (WAXD) experiments. The crystal morphology of the composites exhibits so much microcrystallites because of the fast crystallization rate and the strong interaction between SGF and polymers, which is consistent with the results analysized by the Avrami theory. The nuclei exponent K_g is increased sharply as the SGF added into polymer, and SGF makes PTT easier to crystallize during isothermal crystallization process. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

Study on Mechanical and Tribological Property of Nanometer ZrO2-filled Polyoxymethylene Composites

The polyoxymethylene (POM) matrix composites with different contents of nano-ZrO₂ particles were prepared. The effect of ZrO₂ on the crystallization and thermal property of POM were investigated through polarizing microscopy (PLM) and differential scanning calorimetry (DSC). The surface hardness and the tribological performance were measured by Rockwell sclerometer and ring-on-block tribometer, respectively. The surface morphology of the wear scar were observed by scanning electron microscope (SEM). The results show that the nano-ZrO₂ acted as the nucleation agent in POM and decreased the crystallite size of POM, increased the crystal growth rate. The wear resistance was enhanced and the friction coefficient was changed a little.     

The effect of end groups of PEG on the crystallization behaviors of binary crystalline polymer blends PEG/PLLA

The effect of end groups (2OH, 1OH, 1CH₃ and 2CH₃) of poly(ethylene glycol) (PEG) on the miscibility and crystallization behaviors of binary crystalline blends of PEG/poly(l-lactic acid) (PLLA) were investigated by differential scanning calorimetry (DSC) and polarizing optical microscopy (POM). A single glass-transition temperature was observed in the DSC scanning trace of the blend with a weight ratio of 10/90. Besides, the equilibrium melting point of PLLA decreased with the increasing PEG. A negative Flory interaction parameter, χ₁₂, indicated that the PEG/PLLA blends were thermodynamically miscible. The spherulitic growth rate and isothermal crystallization rate of PEG or PLLA were influenced when the other component was added. This could cause by the change of glass transition temperature, T_g and equilibrium melting point, T⁰_m. The end groups of PEG influenced the miscibility and crystallization behaviors of PEG/PLLA blends. PLLA blended with PEG whose two end groups were CH₃ exhibited the greatest melting point depression, the most negative Flory interaction parameter, the least fold surface free energy, the lowest isothermal crystallization rate and spherulitic growth rate, which meant better miscibility. On the other hand, PLLA blended with PEG whose two end groups were OH exhibited the least melting point depression, the least negative Flory interaction parameter, the greatest fold surface free energy, the greatest isothermal crystallization rate and spherulitic growth rate.