Recrystallization behavior of β‐isotactic polypropylene in homogeneous and heterogeneous matrix–fiber composites

β‐isotactic polypropylene (β‐iPP) cylindritic crystals were produced in homogeneous iPP fiber–matrix composites and heterogeneous polyamide (PA)–iPP fiber–matrix composites under different sample preparation conditions. The melt recrystallization behaviors of the β‐iPP crystals obtained in the homogeneous and heterogeneous composites were studied by optical microscopy. The experimental results show that, by heating the sample to 180 °C, the birefringence contributed by the iPP crystals in both α‐ and β‐forms disappears completely. During the cooling process, the β‐iPP crystals in the homogeneous composite appear again, while the iPP in the heterogeneous composite crystallizes in its α‐form. This demonstrates the different origins of the β‐iPP cylindrites in the homogeneous and heterogeneous composites. While the β‐iPP cylindrites in the heterogeneous composite are associated with the sample preparation procedure, the β‐iPP cylindrites in the homogeneous composite are produced by recrystallization of the molten but incompletely relaxed iPP fibers. In situ observation of the melt recrystallization process shows that the molten iPP oriented fibers crystallize first during the cooling process at relatively higher temperature in the α‐form. Abundant randomly dispersed β‐iPP nuclei formed at the surface of the recrystallized iPP fibers, which generate the β‐iPP cylindrites. Copyright © 2012 Society of Chemical Industry     

Crystal morphology and structure of the β‐form of isotactic polypropylene under supercooled extrusion

A supercooled melt of isotactic polypropylene (iPP) was extruded through a capillary die. Polarized light microscopy (PLM), wide‐angle X‐ray diffraction (WAXD), and differential scanning calorimetry (DSC) were used to investigate the effects of the relatively weak wall shear stress (σ_w), extrusion temperature (T_e), and crystallization temperature (T_c) on the structure and morphology of β‐form isotactic polypropylene (β‐iPP). β‐cylindrites crystals could be observed by PLM in the extruded specimen even at a lower σ_w's (0.020 MPa), and the β‐iPP content increased with decreasing T_e. Under a given T_e of 150°C, the increase in σ_w positively influenced the β‐iPP content. The DSC and WAXD results indicate that the total crystallinity and β‐iPP content increased when T_c was set from 105 to 125°C; the other experimental parameters were kept on the same level. Although T_c was above 125°C, the β‐iPP content obviously decreased, and the total crystallinity continued to increase. On the basis of the influences of σ_w, T_e, and T_c on the β‐iPP crystal morphology and structure, a modified model is proposed to explain the growing of shear‐induced β‐iPP nucleation. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effects of melt structure on crystallization behavior of isotactic polypropylene nucleated with α/β compounded nucleating agents

In this study, the melt structure of isotactic polypropylene (iPP) nucleated with α/β compounded nucleating agents (α/β‐CNA, composed of the α‐NA of 0.15 wt % Millad 3988 and the β‐NA of 0.05 wt % WBG‐II) was tuned by changing the fusion temperature T_f. In this way, the role of melt structure on the crystallization behavior and polymorphic composition of iPP were investigated by differential scanning calorimetry (DSC), wide‐angle X‐ray scattering (WAXD) and scanning electron microscopy (SEM). The results showed that when T_f = 200°C (iPP was fully molten), the α/β‐CNA cannot encourage β‐phase crystallization since the nucleation efficiency (NE) of the α‐NA 3988 was obviously higher than that of the β‐NA WBG‐II. Surprisingly, when T_f was in 179–167°C, an amount of ordered structures survived in the melt, resulting in significant increase of the proportion of β‐phase (achieving 74.9% at maximum), indicating that the ordered structures of iPP played determining role in β‐phase crystallization of iPP nucleated with the α/β‐CNA. Further investigation on iPP respectively nucleated with individual 3988 and WBG‐II showed that as T_f decreased from 200°C to 167°C, the crystallization peak temperature T_c of iPP/3988 stayed almost constant, while T_c of iPP/WBG‐II increased gradually when T_f < 189°C and became higher than that of iPP/3988 when T_f decreased to 179°C and lower, which can be used to explain the influence of ordered structure and α/β‐CNA on iPP crystallization. Using this method, the selection of α‐NA for α/β‐CNA can be greatly expanded even if the inherent NE of β‐NA is lower than that of the α‐NA. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41355.     

Effect of α‐ and β‐nucleating agents on the fracture behavior of polypropylene‐co‐ethylene

The effect of α‐ and β‐nucleating agents (NA) of various amounts on the fracture behavior of polypropylene‐co‐ethylene (CPP) was evaluated using the essential work of fracture (EWF) method. The specific EWF values of CPPs incorporated with α‐NA of different amount were all lower than that of pure CPP, while the specific nonessential work of fracture was the highest at relative low α‐NA loading (0.1 wt %), and then decreased with further increasing amount of α‐NA. Similar trend of variation was observed with increasing amount of β‐NA in CPP, and it was found that the variation of K_β for β‐NA nucleated CPP versus NA content accorded well with the EWF versus NA content, which indicated that the addition of β‐NA could lead to effectively increased β‐crystal content and consequently improved fracture resistance of CPP. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Combined effect of β‐nucleating agent and processing melt temperature on the toughness of impact polypropylene copolymer

The phase morphology and toughening behavior of impact polypropylene copolymer (IPC) with and without nucleating agent (NA), prepared at different processing melt temperatures (T_p), were investigated. Interestingly, three different structures can be formed in the IPC samples by adding NA or tuning T_p. A well‐defined core–shell structure is obtained in samples with α‐NA or without NA prepared at all T_p. A developing multilayered structure is mainly formed at high T_p with added β‐NA, while an incomplete phase separation structure with interpenetrating chains is the dominant structure for IPC samples prepared at low T_p with added β‐NA. In this case, because of the synergistic effect between phase morphology and relatively high β‐form crystal content, the chain interaction among the components and chain mobility of the amorphous portion of IPC are distinctly improved, resulting in a largely improved toughness under 0 °C. This improvement in toughness is very important for applications. © 2012 Society of Chemical Industry     

γ‐FOX‐7: Structure of a High Energy Density Material Immediately Prior to Decomposition

1,1‐Diamino‐2,2‐dinitroethene, C₂H₄N₄O₄ (FOX‐7), is a novel high energy density material with low friction and impact sensitivity and a high activation barrier to detonation. In this study, the previously unknown crystal structure of the γ‐polymorph of trimorphic FOX‐7 is reported. γ‐FOX‐7 is stable from ∼435 K until the compound decomposes just above 504 K. A single crystal of α‐FOX‐7 (P2₁/n, Z=4, a=694.67(7) pm, b=668.87(9) pm, c=1135.1(1) pm, β=90.14(1)°, T=373 K) was first transformed into a single crystal of β‐FOX‐7 (P2₁2₁2₁, Z=4, a=698.6(1) pm, b=668.6(2) pm, c=1168.7(3) pm, T=423 K) and then into a single crystal of γ‐FOX‐7 at 450 K. The γ‐FOX‐7 crystal was then subsequently quenched to 200 K. The structure of γ‐FOX‐7 (P2₁/n, Z=8, a=1335.4(3) pm, b=689.5(1) pm, c=1205.0(2) pm, β=111.102(8)°, T=200 K) consists of four planar layers, each containing two crystallographically independent FOX‐7 molecules found in the asymmetric unit.     

α‐Crystallin Modulates its Chaperone Activity by Varying the Exposed Surface

The α‐crystallin family of small heat shock proteins possesses chaperone activity in response to stress and is involved in several neurological, muscular, and ophthalmic pathologies. This family includes the vertebrate lens protein α‐crystallin, associated with cataract disease. In this study, by combining small‐angle X‐ray and light scattering techniques, the structure and shape of α‐crystallin was revealed in its native state and after a transition caused by heat stress. Below critical temperature (T_c), α‐crystallin appears as an ellipsoid with a central cavity; whereas at high temperatures the cavity almost disappears, and the protein rearranges its structure, increasing the solvent‐exposed surface while retaining the ellipsoidal symmetry. Contextually, at T_c, α‐crystallin chaperone binding shows an abrupt increase. By modelling the chaperone activity as the formation of a complex composed of α‐crystallin and an aggregating substrate, it was demonstrated that the increase of α‐crystallin‐exposed surface is directly responsible for its gain in chaperone functionality.     

Negative effect of stretching on the development of β‐phase in β‐nucleated isotactic polypropylene

On the premise that shear in the slit die of an extruder was minimized as far as possible, β‐nucleated isotactic polypropylene (iPP) was extruded. Simultaneously, once the extrudate (in the melt state) left the die exit, it was stretched at various stretching rates (SRs). For iPP with a low content of β‐nucleating agent (β‐NA), the crystallinity of β‐phase (X_β) initially increases with increasing SR, and then decreases slightly with further increase in SR. However, for iPP containing a higher content of β‐NA, with increasing SR, X_β decreases monotonically, indicating a negative effect of SR on β‐phase formation. Small‐angle X‐ray scattering and polarized optical microscopy experiments reveal that, when SR is less than 30 cm min^?1, the increasing amount of row nuclei induced by increasing SR is mainly responsible for the increase of X_β. In contrast, when SR exceeds 30 cm min^?1, the overgrowth of shish structures unexpectedly restrains the development of β‐phase, and spatial confinement is considered as a better explanation for the suppression of β‐phase. Copyright © 2011 Society of Chemical Industry     

N,N′‐Dioxide‐Magnesium Ditriflate Complex‐Catalyzed Asymmetric α‐Hydroxylation of β‐Keto Esters and β‐Keto Amides

The highly catalytic asymmetric α‐hydroxylation of 1‐tetralone‐derived β‐keto esters and β‐keto amides using tert‐butyl hydroperoxide (TBHP) as the oxidant was realized by a chiral N,N′‐dioxide‐magnesium ditriflate [Mg(OTf)₂] complex. A series of corresponding chiral α‐hydroxy dicarbonyl compounds was obtained in excellent yields (up to 99%) with excellent enantioselectivities (up to 98% ee). The products were easily transformed into useful building blocks and the precursor of daunomycin was achieved in an asymmetric catalytic way for the first time.     

Critical role of depressurization and effects of saturation conditions in the formation of β‐Crystal during isotactic polypropylene foaming with supercritical CO2

The melting behavior and crystalline forms of isotactic polypropylene (iPP) samples crystallized under different conditions of pressure and temperature were investigated using differential scanning calorimeter (DSC) and wide‐angle X‐ray diffraction (WAXD), respectively. When treated with dynamic supercritical CO₂(Sc‐CO₂), iPP samples undergo the formation of β‐crystal that does not occur on the treatment with atmospheric pressure and static supercritical CO₂(Sc‐CO₂) pressure. In addition, the relative content of β‐crystal has deep dependence on melt state and depressurization rate. Depressurization plays very critical role in the formation of β‐crystal by means of imposing three‐dimensional tensile field during cell growth. The tensile field induced α‐row nuclei where the formation of β‐crystal occurred. This finding will provide one new method to induce β‐crystal in iPP parts. POLYM. ENG. SCI. 56:980–986, 2016. © 2016 Society of Plastics Engineers     

Effects of melt structure on non‐isothermal crystallization behavior of isotactic polypropylene nucleated with α/β compounded nucleating agents

In this study, the effects of melt structure (tuned by controlling the fusion temperature T_f) on non‐isothermal crystallization and subsequent melting behaviors of isotactic polypropylene (iPP) nucleated with α/β compounded nucleating agents (α/β‐CNAs) have been further investigated. The results show that under all cooling rates studied (2–40°C/min), the crystallization temperature on cooling curves increased gradually with decrease of T_f, meanwhile, when T_f was in temperature range of 166°C–179°C where ordered structures survived in the melt (defined as Region II), crystallization activation energy ΔE was found to be evidently lower compared with that when T_f > 179°C or T_f < 166°C. The results of subsequent heating showed that occurrence of Ordered Structure Effect can be observed at all the cooling rates studied; the location of the Region II was constant when cooling rate varied; Low cooling rate encouraged formation of more β‐phase triggered by ordered structure. Moreover, the role of ordered structure on β‐α recrystallization was comparatively studied by tuning the end temperature of recooling (T_end) after held at T_f, and it was found that ordered structure encouraged the formation of β‐phase with high thermal stability at low temperature part of Region II, while enhanced the β‐crystal with relatively low thermal stability at high temperature part of Region II. POLYM. ENG. SCI., 57:989–997, 2017. © 2016 Society of Plastics Engineers     

Highly Enantioselective Phase‐Transfer Catalytic α‐Alkylation of α‐tert‐Butoxycarbonyllactams: Construction of β‐Quaternary Chiral Pyrrolidine and Piperidine Systems

A new enantioselective α‐alkylation of α‐tert‐butoxycarbonyllactams for the construction of β‐quaternary chiral pyrrolidine and piperidine core systems is reported. α‐Alkylations of N‐methyl‐α‐tert‐butoxycarbonylbutyrolactam and N‐diphenylmethyl‐α‐tert‐butoxycarbonylvalerolactam under phase‐transfer catalytic conditions (solid potassium hydroxide, toluene, −40 °C) in the presence of (S,S)‐3,4,5‐trifluorophenyl‐3,3′,5,5′‐tetrahydro‐2,6‐bis(3,4,5‐trifluorophenyl)‐4,4′‐spirobi[4H‐dinaphth[2,1‐c:1′,2′‐e]azepinium] bromide [(S,S)‐NAS Br] (5 mol%) afforded the corresponding α‐alkyl‐α‐tert‐butoxycarbonyllactams in very high chemical (up to 99%) and optical yields (up to 98% ee). Our new catalytic systems provide attractive synthetic methods for pyrrolidine‐ and piperidine‐based alkaloids and chiral intermediates with β‐quaternary carbon centers.     

Nonisothermal crystallization and melting behavior of β‐nucleated isotactic polypropylene and polyamide 66 blends

A highly novel nano‐CaCO₃ supported β‐nucleating agent was employed to prepare β‐nucleated isotactic polypropylene (iPP) blend with polyamide (PA) 66, β‐nucleated iPP/PA66 blend, as well as its compatibilized version with maleic anhydride grafted PP (PP‐g‐MA), maleic anhydride grafted polyethylene‐octene (POE‐g‐MA), and polyethylene‐vinyl acetate (EVA‐g‐MA), respectively. Nonisothermal crystallization behavior and melting characteristics of β‐nucleated iPP and its blends were investigated by differential scanning calorimeter and wide angle X‐ray diffraction. Experimental results indicated that the crystallization temperature (T) of PP shifts to high temperature in the non‐nucleated PP/PA66 blends because of the α‐nucleating effect of PA66. T of PP and the β‐crystal content (K_β) in β‐nucleated iPP/PA66 blends not only depended on the PA66 content, but also on the compatibilizer type. Addition of PP‐g‐MA and POE‐g‐MA into β‐nucleated iPP/PA66 blends increased the β‐crystal content; however, EVA‐g‐MA is not benefit for the formation of β‐crystal in the compatibilized β‐nucleated iPP/PA66 blend. It can be relative to the different interfacial interactions between PP and compatibilizers. The nonisothermal crystallization kinetics of PP in the blends was evaluated by Mo's method. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Shear‐induced β‐form polypropylene in long chain branching isotactic polypropylene

Long chain branching polypropylene (LCBPP) with different long chain branching (LCB) contents were prepared by reactive extrusion in the presence of styrene and benzoyl peroxide, and their shear‐induced crystallization behaviors were investigated. The results indicated that the LCB structure extended the relaxation time of LCBPP in the molten state, which led to the formation of β‐form polypropylene under shear and high cooling rate. The content of β‐form (K_β) increased with the increase of LCB content, shearing rate and cooling rate. The K_β value of LCBPP3 whose weight average molecular weight was 920,000 g mol^?1 could be up to 52.0% with a shear rate of 60 s^?1 associated with a cooling rate of 280°C min^?1. This study is expected not only to have a deeper understanding of the shear‐induced crystallization behavior of LCBPP, but also provide a new strategy to obtain high level β‐form polypropylene. POLYM. ENG. SCI., 56:240–247, 2016. © 2015 Society of Plastics Engineers     

Probing the Peptidylglycine α‐Hydroxylating Monooxygenase Active Site with Novel 4‐Phenyl‐3‐butenoic Acid Based Inhibitors

Specific inhibition of the copper‐containing peptidylglycine α‐hydroxylating monooxygenase (PHM), which catalyzes the post‐translational modification of peptides involved in carcinogenesis and tumor progression, constitutes a new approach for combating cancer. We carried out a structure–activity study of new compounds derived from a well‐known PHM substrate analogue, the olefinic compound 4‐phenyl‐3‐butenoic acid (PBA). We designed, synthesized, and tested various PBA derivatives both in vitro and in silico. We show that it is possible to increase PBA affinity for PHM by appropriate functionalization of its aromatic nucleus. Compound 2 d , for example, bears a meta‐benzyloxy substituent, and exhibits better inhibition features (K_i=3.9 μM , k_inact/K_i=427 M ^?1 s^?1) than the parent PBA (K_i=19 μM , k_inact/K_i=82 M ^?1 s^?1). Docking calculations also suggest two different binding modes for PBA derivatives; these results will aid in the development of further PHM inhibitors with improved features.     

Oxygen‐Involved Oxidative Deacetylation of α‐Substituted β‐Acetyl Amides – Synthesis of α‐Keto Amides

α‐Substituted β‐acetyl amides could undergo C C bond cleavage to form α‐keto amides when treated with copper(II) chloride (CuCl₂) and boron trifluoride diethyl etherate (BF₃⋅OEt₂) under an oxygen atmosphere. The yield can be increased by the addition of tert‐butyl hydroperoxide which alone can also effect the reaction. The reaction provides a new protocol for the synthesis of α‐keto amides.

     

Behavior of α‐ and β‐cyclodextrin‐encapsulated allyl isothiocyanate as slow‐release additives in polylactide‐co‐polycaprolactone films

The natural antibacterial agent allyl isothiocyanate (AITC) encapsulated in either α‐ or β‐cyclodextrin (CD) has previously been evaluated as a slow‐release additive in polylactide‐co‐polycaprolactone (PLA–PCL) films designed for use in cheese packaging. In the research described in this article, thermogravimetric analysis (TGA) and thermogravimetric analysis in tandem with mass spectrometry (TGA–MS) were used to explore the thermal properties of CD‐encapsulated AITC complexes as well as those of PLA–PCL films containing these complexes. To our knowledge, this is the first reported application of the TGA–MS technique to explore the thermal stability of CD‐entrapped AITC and the first study to report differences in thermal stability of AITC in α‐and β‐CD cavities in the solid state. Observed differences in the thermal degradation profile of films containing the CD complexes can be explained if AITC binds more strongly to β‐CD than to α‐CD. This hypothesis has been reinforced by gas chromatography (GC) and high performance liquid chromatography (HPLC) studies, the results of which suggest that a new covalently bound AITC–CD complex may be formed when incorporating the β‐CD complex of AITC in PLA–PCL films but not when incorporating the α‐CD complex of AITC. This finding means that the α‐CD complex of AITC would be preferred in situations where adequate long‐term controlled release of AITC from polymer films is required, as for example in the case of active packaging applications. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Polymorphism and spherulite morphology of poly(1,4‐butylene adipate)/organically‐modified layered double hydroxide nanocomposites

A novel biodegradable poly(1,4‐butylene adipate)/organically‐modified layered double hydroxide (PBA/m‐LDH) nanocomposites are synthesized using the solution mixing process. The m‐LDH is originally prepared with magnesium nitrate hexahydrote (Mg(NO₃)₂ 6H₂O), aluminum nitrate‐9‐hydrate (Al(NO₃)₃ 9H₂O), oleic acid, and sorbitol by a novel one‐step co‐precipitation method to intercalate the organo‐modifier of oleic acid and sorbitol into the interlayer of LDH. The structure and morphology of the PBA/m‐LDH nanocomposites are characterized using X‐ray diffraction and transmission electron microscopy (TEM). It has been shown that the m‐LDH is exfoliated and well distributed in PBA matrix. The effect of m‐LDH on the polymorphic crystal and morphology of PBA at various crystallization temperatures (T_cs) would be investigated using WAXD and POM. Both data indicate that the addition of m‐LDH can change the starting formation temperature of α‐form crystals. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42526.     

Poly(vinylidene fluoride) membrane with piezoelectric β‐form prepared by immersion precipitation from mixed solvents containing an ionic liquid

Poly(vinylidene fluoride) (PVDF) membranes with exclusive β‐form have been directly obtained by immersion precipitation from the mixed solvents containing an ionic liquid (IL). In contrast, without the IL only the α‐form is generated. The ion–dipole interactions between the IL and PVDF chains should account for the formation of the β‐form with TTTT conformation. In addition, the presence of the IL accelerates the crystallization and gelation of PVDF, responsible for the particulate morphology and high water flux in the membranes. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40505.     

Synthesis and Properties of Alkoxyethyl β‐d‐Xylopyranoside

In order to improve the water solubility of sugar‐based surfactants, alkyl β‐d‐ xylopyranosides, novel sugar‐based surfactants, 1,2‐trans alkoxyethyl β‐d‐ xylopyranosides, with alkyl chain length n = 6–12 were stereoselectively prepared by the trichloroacetimidate method. Their properties including hydrophilic–lipophilic balance (HLB) number, water solubility, surface tension, emulsification, foamability, thermotropic liquid crystal, and hygroscopicity were investigated. The results indicated that their HLB number decreased with increase of alkyl chain, the water solubility improved since the hydrophilic oxyethene (─OCH₂CH₂─) fragment was introduced. The dissolution process was entropy driven at 25–45 °C for alkyl chain length n = 6–10. Octyloxyethyl β‐d‐ xylopyranoside had the best foaming ability. Nonyloxyethyl β‐d‐ xylopyranoside had the best foam stability and the emulsifying ability was better in toluene/water system than in rapeseed oil/water system. The surface tension of in aqueous solution dropped to 27.8 mN m^?1 at the critical micelle concentration, and it also showed the most distinct thermotropic liquid phases with cross pattern texture upon heating and the fan schlieren texture on cooling. Hexyloxyethyl β‐d‐ xylopyranoside possessed the strongest hygroscopicity. Based on the effective improvement of water solubility, the prepared alkoxyethyl β‐d‐ xylopyranosides showed excellent surface activity and are expected to develop their practical application as a class of novel sugar‐based surfactants.