Synthesis and properties of novel aromatic polyamides with xanthene cardo groups

Two novel monomers, 9,9‐bis[4‐(4‐carboxyphenoxy)phenyl]xanthene (BCAPX) and 9,9‐bis[4‐(4‐aminophenoxy)phenyl]xanthene (BAPX) were prepared in two main steps starting from nucleophilic substitution of 9,9‐bis(4‐hydroxyphenyl)xanthene (BHPX) with p‐fluorobenzonitrile and p‐chloronitrobenzene, respectively. Using triphenyl phosphite and pyridine as condensing agents, two series of polyamides containing xanthene cardo groups with the inherent viscosities (0.82–1.32 dL/g) were prepared by polycondensation from BCAPX with various aromatic diamines or from BAPX with various aromatic dicarboxylic acids in an N‐methyl‐2‐pyrrolidone (NMP) solution containing dissolved calcium chloride, respectively. All new polyamides were amorphous and readily soluble in various polar solvents such as N,N‐dimethylformamide (DMF), NMP, N,N‐dimethylacetamide (DMAc) and pyridine. These polymers showed relatively high glass transition temperatures between 264 and 308°C, decomposition temperatures at 10% weight loss ranging from 502 to 540°C and 488 to 515°C in nitrogen and air, respectively, and char yields at 800°C in nitrogen higher than 56%. Transparent, flexible, and tough films of these polymers cast from DMAc solutions exhibited tensile strengths ranging from 86 to 109 MPa, elongations at break from 13 to 22%, and initial moduli from 2.15 to 2.63 GPa. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Polyimides containing s‐triazine rings

A series of new polyimides containing s‐triazine rings have been synthesized via Diels–Alder intermolecular polymerization of 2,6‐bis(2‐furanylmethylimino)‐4‐isopropoxy‐1,3,5‐triazine with various bis(maleimide)s. All the poly(imino‐s‐triazine imide)s were characterized by elemental analyses, FTIR spectral studies, number average molecular weight ( M _n) by non‐aqueous conductometric titration and thermogravimetry. Glass‐fibre reinforced composites were prepared via an in situ Diels–Alder intermolecular reaction between 2,6‐bis(2‐furanylmethylimino)‐4‐isopropoxy‐1,3,5‐triazine and various bis(maleimide)s. The composites were characterized for chemical resistivity and mechanical properties. © 2003 Society of Chemical Industry     

Synthesis and characterization of poly(arylene ether s‐triazine)s containing alkyl‐, aryl‐ and chloro‐substituted phthalazinone moieties in the main chain

Soluble and heat‐resistant polymers have great potential for use as processable, high‐temperature polymeric materials. In this study, four types of new poly(arylene ether s‐triazine)s containing alkyl‐, aryl‐ and chloro‐substituted phthalazinone moieties in the main chain were prepared through direct solution polycondensation of 2,4‐bis(4‐fluorophenyl)‐6‐phenyl‐s‐triazine with each of methyl‐, phenyl‐ and chloro‐substituted phthalazinones. A key feature of these polymers is the incorporation of phthalazinone and side groups into the poly(arylene ether s‐triazine) backbone to endow them with good solubility while maintaining other attractive properties. The polymers were obtained in high yields, and had inherent viscosities ranging from 0.38 to 0.55 dL g^?1. Their structure was characterized using Fourier transform infrared and NMR spectra and elemental analysis. The polymers were almost amorphous, and soluble in N‐methyl‐2‐pyrrolidone, pyridine, N,N‐dimethylacetamide, hot N,N‐dimethylformamide and sulfolane. Tough and nearly transparent films obtained by direct solution casting exhibited good mechanical properties. The resulting polymers displayed glass transition temperatures ranging from 255 to 265 °C and thermal decomposition temperatures for 10% mass loss ranging from 476 to 599 °C, according to differential scanning calorimetry and thermogravimetric analysis, respectively. The reactivity of substituted phthalazinones in nucleophilic displacement reactions and the effect of the side groups on the physical properties of the polymers were also investigated. The results obtained revealed that such s‐triazine‐containing polymers possessed good solubility while maintaining acceptable thermal stability and high mechanical strength with the incorporation of alkyl‐, aryl‐ and chloro‐substituted phthalazinone moieties into their backbones, which makes them an attractive series of high‐performance structural materials. Copyright © 2010 Society of Chemical Industry     

Synthesis and properties of novel polyamides containing sulfone‐ether linkages and xanthene cardo groups

In order to obtain polyamides with enhanced solubility and processability, as well as good mechanical and thermal properties, several novel polyamides containing sulfone‐ether linkages and xanthene cardo groups based on a new diamine monomer, 9,9‐bis[4‐(4‐aminophenoxy)phenyl]xanthene (BAPX), were investigated. The BAPX monomer was synthesized via a two‐step process consisting of an aromatic nucleophilic substitution reaction of readily available 4‐chloronitrobenzene with 9,9‐bis(4‐hydroxyphenyl)xanthene in the presence of potassium carbonate in N,N‐dimethylformamide, followed by catalytic reduction with hydrazine and Pd/C. Four novel aromatic polyamides containing sulfone‐ether linkages and xanthene cardo groups with inherent viscosities between 0.98 and 1.22 dL g^?1 were prepared by low‐temperature polycondensation of BAPX with 4,4′‐sulfonyldibenzoyl chloride, 4,4′‐[sulfonyl‐bis(4‐phenyleneoxy)]dibenzoyl chloride, 3,3′‐[sulfonyl‐bis(4‐phenyleneoxy)]dibenzoyl chloride and 4,4′‐[sulfonyl‐bis(2,6‐dimethyl‐1,4‐phenyleneoxy)]dibenzoyl chloride in N,N‐dimethylacetamide (DMAc) solution containing pyridine. All these new polyamides were amorphous and readily soluble in various polar solvents such as DMAc and N‐methylpyrrolidone. These polymers showed relatively high glass transition temperatures in the range 238–298 °C, almost no weight loss up to 450 °C in air or nitrogen atmosphere, decomposition temperatures at 10% weight loss ranging from 472 to 523 °C and 465 to 512 °C in nitrogen and air, respectively, and char yields at 800 °C in nitrogen higher than 50 wt%. Transparent, flexible and tough films of these polymers cast from DMAc solution exhibited tensile strengths ranging from 78 to 87 MPa, elongations at break from 9 to 13% and initial moduli from 1.7 to 2.2 GPa. Primary characterization of these novel polyamides shows that they might serve as new candidates for processable high‐performance polymeric materials. Copyright © 2010 Society of Chemical Industry     

Synthesis and properties of polyamides based on 5,5′‐bis[4‐(4‐aminophenoxy)phenyl]‐hexahydro‐4,7‐methanoindan

A new diamine 5,5′‐bis[4‐(4‐aminophenoxy)phenyl]‐hexahydro‐4,7‐methanoindan ( 3 ) was prepared through the nucleophilic displacement of 5,5′‐bis(4‐hydroxylphenyl)‐hexahydro‐4,7‐methanoindan ( 1 ) with p‐halonitrobenzene in the presence of K₂CO₃ in N,N‐dimethylformamide (DMF), followed by catalytic reduction with hydrazine and Pd/C in ethanol. A series of new polyamides were synthesized by the direct polycondensation of diamine 3 with various aromatic dicarboxylic acids. The polymers were obtained in quantitative yields with inherent viscosities of 0.76–1.02 dl g⁻¹. All the polymers were soluble in aprotic dipolar solvents such as N,N‐dimethylacetamide (DMAc) and N‐methyl‐2‐pyrrolidone (NMP), and could be solution cast into transparent, flexible and tough films. The glass transition temperatures of the polyamides were in the range 245–282 °C; their 10% weight loss temperatures were above 468 °C in nitrogen and above 465 °C in air. © 2000 Society of Chemical Industry     

High‐optical transparency and low‐dielectric constant of new organosoluble polyamides containing trifluoromethyl and xanthene groups

A series of fluorinated polyamides was prepared directly by low‐temperature polycondensation of a new cardo diacid chloride, 9,9‐bis[4‐(4‐chloroformylphenoxy)phenyl]xanthene (BCPX), with various diamines containing trifluoromethyl substituents in N,N‐dimethylacetamide (DMAc). Almost all polyamides showed excellent solubility in amide‐type solvents such as DMAc and could also be dissolved in pyridine, m‐cresol, and tetrahydrofuran. These polymers had inherent viscosities between 0.77 and 1.31 dL g^?1, and their weight‐average molecular weights and number‐average molecular weights were in the range of 69,000–102,000 and 41,000–59,000, respectively. The resulting polymers showed glass transition temperatures between 240–258°C and 10% weight loss temperatures ranging from 484°C to 517°C and 410°C to 456°C in nitrogen and air, respectively, and char yields at 800°C in nitrogen higher than 55%. All polymers were amorphous and could be cast into transparent, light‐colored, and flexible films with tensile strengths of 81–100 MPa, elongations at break of 8–12%, and tensile modulus of 1.6–2.1 GPa. These polymers had low‐dielectric constants of 3.34–3.65 (100 kHz), low‐moisture absorption in the range of 0.76–1.91%, and high transparency with an ultraviolet–visible absorption cut‐off wavelength in the 322–340 nm range. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis and characterization of aromatic–aliphatic polyamides

A new monomer, 2,5‐bis(4‐carboxy methylene phenyl)‐3,4‐diphenyl thiophene (V) has been synthesized and characterized by physical and spectroscopic methods. A series of eight aromatic–aliphatic polyamides was prepared from the (V) and different aromatic diamines using Yamazaki's direct phosphorylation reaction. The polyamides were characterized by IR spectroscopy, viscosity measurements, and thermal analysis. An excellent yield of these polyamides was obtained, with inherent viscosities in the range of 0.28 to 0.67 dL/g, and the polyamide were readily soluble in aprotic polar solvents such as N‐methyl‐2‐pyrrolidone, N‐N‐dimethyl acetamide, dimethyl sulphoxide, and so forth. Polyamides could be cast into transparent and flexible films. They had glass‐transition temperatures of 225–273°C. When evaluated by thermogravimetry, thermal analysis of the polyamides showed no weight loss below 311°C, and the char yield in air at 900°C was 55%–67%. The structure–property correlation among these polyamides is also discussed. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 566–571, 2001     

Synthesis and characterization of organosoluble poly(arylate‐imide)s prepared from direct polycondensation of bis(trimellitimide)‐diacids and various bisphenols

Three diimide‐diacids, 2,2‐bis[4‐(4‐trimellitimidophenoxy)phenyl]hexafluoropropane ( I‐A ), 2,2‐bis[4‐(4‐trimellitimidophenoxy)phenyl]propane ( I‐B ), and 5,5′‐bis[4‐ (4‐trimellitimidophenoxy)phenyl]hexahydro‐4,7‐methanoindan ( I‐C ), were prepared by the azeotropic condensation of trimellitic anhydride with three analogous diamines. Three series of alternating aromatic poly(arylate‐imide)s, having inherent viscosities of 0.41–0.82 dL/g, were synthesized from these diimide‐diacids ( I‐A , I‐B , and I‐C ) with various bisphenols by direct polycondensation using diphenyl chlorophosphate and pyridine as condensing agents. All of the polymers were readily soluble in a variety of organic solvents such as N‐methyl‐2‐pyrrolidone, N,N‐dimethylacetamide, and even in the less polar tetrahydrofuran. These polymers could be cast into transparent and tough films, which had strength at break values ranging from 73 to 98 MPa, elongation at break from 6 to 11%, and initial modulus from 1.6 to 2.2 GPa. The softening temperatures of the polymers were recorded at 145–248°C. They had 10% weight loss at a temperature above 450°C and left 35–51% residue even at 800°C in nitrogen. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3818–3825, 2003     

Synthesis and characterization of new polyamides derived from 1,3‐(4‐carboxy phenoxy) propane and aromatic diamines

Six new polyamides 5a‐f containing flexible trimethylene segments in the main chain were synthesized through the direct polycondensation reaction of 1,3‐(4‐carboxy phenoxy) propane 3 with six derivatives of aromatic diamines 4a‐f in a medium consisting of N‐methyl‐2‐pyrrolidone, triphenyl phosphite, calcium chloride, and pyridine. The polycondensation reaction produced a series of novel polyamides containing flexible trimethylene segments in the main chain in high yield with inherent viscosities between 0.32 and 0.68 dL/g. The resulted polymers were fully characterized by means of FTIR spectroscopy, elemental analyses, inherent viscosity, and solubility tests. Thermal properties of these polymers were investigated by using thermal gravimetric analysis (TGA) and differential thermal gravimetric (DTG). The glass‐transition temperatures of these polyamides were recorded between 165 and 190°C by differential scanning calorimetry, and the 10% weight loss temperatures were ranging from 360 to 430°C under nitrogen. 1,3‐(4‐Carboxy phenoxy) propane 3 was prepared from the reaction of 4‐hydroxy benzoic acid 1 with 1,3‐dibromo propane 2 in the presence of NaOH solution. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis and characterization of silicon‐containing poly(amide‐amide)s

A modified new aromatic diacid, bis[(4‐carboxyphenyl) 4‐benzamide] dimethylsilane (IV) with preformed amide linkages and a silicon moiety was synthesized and characterized by IR, NMR, mass spectroscopy, and a physical constant. Novel poly(amide‐amide)s were synthesized from IV and aromatic diamines by Yamazaki's direct polyamidation method in N‐methyl pyrrolidinone. The polymers were obtained in excellent yields and showed reduced viscosities in the range of 0.42–6.15 dL/g. They were readily soluble in aprotic polar solvents. These poly(amide‐amide)s showed glass‐transition temperatures of 303–378°C as measured by DSC and showed no weight loss below 377°C in a nitrogen atmosphere. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1610–1617, 2001     

Synthesis and characterization of new polyamides containing p‐phenylenediacryloyl moieties in the main chain

Six new polyamides 8a–f containing p‐phenylenediacryloyl moieties in the main chain were prepared by the direct polycondensation reaction of bis(p‐amidobenzoic acid)‐p‐phenylene diacrylic acid 6 with 1,4‐diphenylene diamine 7a , 1,3‐diamino toluene 7b , 1,5‐diamino naphthalene 7c , 4,4′‐diamino diphenyl ether 7d , 4,4′‐diamino diphenyl sulfone 7e , and 3,3′‐diamino diphenylsulfone 7f by using thionyl chloride, N‐methyl‐2‐pyrolidone, and pyridine as condensing agents. These new polymers 8a–f were obtained in high yield and inherent viscosity between 0.35–0.65 dL/g. The resulting polyamides were characterized by elemental analysis, viscosity measurements, thermal gravimetric analysis (TGA and DTG), solubility test, FTIR and UV–vis spectroscopy. Diacid acid 6 as a new monomer containing p‐phenylenediacryloyl moiety was synthesized by using a three‐step reaction. First, p‐phenylenediacrylic acid 3 was prepared by reaction of terephthal aldehyde 1 with malonic acid 2 in the presence of pyridine, then diacid 3 was converted to p‐phenylenediacryloyl chloride 4 by reaction with thionyl chloride. Finally, bis(p‐amidobenzoic acid)‐p‐phenylene diacrylic acid 6 was prepared by the condensation reaction of phenylenediacryloyl chloride 4 with p‐aminobenzoic acid 5 . © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis and characterization of novel wholly para‐oriented aromatic polyamide‐hydrazides containing sulfone‐ether linkages

Four novel wholly para‐oriented aromatic polyamide‐hydrazides containing flexibilizing sulfone‐ether linkages in their main chains have been synthesized from 4‐amino‐3‐hydroxy benzhydrazide (4A3HBH) with either 4,4′‐sulfonyldibenzoyl chloride (SDBC), 4,4′‐[sulfonylbis(1,4‐phenylene)dioxy]dibenzoyl chloride (SODBC), 4,4′‐[sulfonylbis(2,6‐dimethyl‐1,4‐phenylene)dioxy]dibenzoyl chloride (4MeSODBC), or 4,4′‐(1,4‐phenylenedioxy)dibenzoyl chloride (ODBC) via a low‐temperature solution polycondensation reaction. A polyamide‐hydrazide without the flexibilizing linkages is also investigated for comparison. It was synthesized from 4A3HBH and terephthaloyl chloride (TCl) by the same synthetic route. The intrinsic viscosities of the polymer ranged from 2.85 to 4.83 dL g^?1 in N,N‐dimethyl acetamide (DMAc) at 30°C and decreased with introducing the flexibilizing linkages into the polymer. All the polymers were soluble in DMAc, N,N‐dimethyl formamide (DMF), and N‐methyl‐2‐pyrrolidone (NMP), and their solutions could be cast into films with good mechanical strengths. Further, they exhibited a great affinity to water sorption. Their solubility and hydrophilicity increased remarkably by introducing the flexibilizing linkages. The polymers could be thermally cyclodehydrated into the corresponding poly(1,3,4‐oxadiazolyl‐benzoxazoles) approximately in the region of 295–470°C either in nitrogen or in air atmospheres. The flexibilizing linkages improve the solubility of the resulting poly(1,3,4‐oxadiazolyl‐benzoxazoles) when compared with poly(1,3,4‐oxadiazolyl‐benzoxazoles) free from these linkages. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Novel fluorescent porous hyperbranched aromatic polyamide containing 1,3,5‐triphenylbenzene moieties: Synthesis and characterization

In this thesis, two novel porous hyperbranched poly(1,3,5‐tris(4‐carboxyphenyl) benzene p ‐phenylenediamine) amides with different terminal functional groups are synthesized through an A₂ + B₃ approach using 1,3,5‐tri(4‐carboxyl phenyl) benzene (H₃BTB) and p ‐phenylenediamine as raw material, N ‐methyl‐pyrrolidone as solvent, triphenyl phosphite and pyridine as dehydrating agent, by means of regulating the mole ratio of the monomers. The chemical structures of the prepared hyperbranched polymers are characterized by Fourier transform infrared spectroscopy and nuclear magnetic resonance (¹H‐NMR and ¹³C‐NMR) analysis. These two polymers can be soluble in dimethyl sulfoxide (DMSO) and N ,N ‐dimethyl formamide (DMF). Their DMSO solutions exhibit strong blue fluorescence, especially for the amino terminated polymer HP‐NH₂. While in DMF solution, the two polymers emit strong green fluorescence. These two polymers are porous polymers with the Brunauer?Emmett?Teller surface areas of 4.53 and 24.52 m²/g for HP‐COOH and HP‐NH₂, respectively. They are potential useful in the areas of storage, separation, catalysis, and light emitting. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44505.     

Synthesis and characterization of polyamides containing arylene sulfide-sulfone groups

Polyamides containing arylene sulfide as well as arylene sulfide-sulfone linkages were prepared from bis(4-phenylthio)dibenzoyl chloride (BPCl), 4,4′-[sulfonylbis(4-phenylthio)]dibenzoyl chloride (SPCl) and aromatic diamines both by solution and interfacial polymerization techniques. In the solution polymerization the effect of two different acid acceptors, lithium chloride and triethylamine, on inherent viscosity of the polyamides was studied. The effect of aromatic sulfone ether diamines and conventional aromatic diamines on viscosity and thermal properties of polyamides was also investigated. The polyamides prepared were characterized by IR, ¹H NMR, elemental analysis, solution viscosity, thermogravi-metry, differential scanning calorimetry and X-ray diffraction. Thermal and physical properties of polyamides prepared from BPCl and SPCl were compared.     

Synthesis,characterization, and properties of novel fluorine containing aromatic polyamides

A series of novel fluorine containing aromatic polyamides were synthesized by the direct polycondensation of various fluorine containing aromatic diamines and commercially available 5‐t‐butyl isophthalic acid. These polyamides have good solubility in several organic solvents such as dimethylformamide, N,N‐dimethylacetamide, 1‐Methyl‐2‐pyrrolidone, dimethyl sulfoxide, and tetrahydrofuran. The synthesized polymers exhibited inherent viscosities up to 0.93 dL/g and M_w up to 1,52,000 with PDI of 2.49. The polyamides exhibited good thermal stability up to 489°C for 10% weight loss in nitrogen and high glass transition temperature up to 273°C. Dynamic mechanical analysis showed a very good retention of storage modulus up to the glass transition temperature. The tan δ peak value at 1 Hz was used to calculate the T_g and these values are in good agreement with differential scanning calorimetry data. The polyamide films were flexible with tensile strength up to 72 MPa, elongations at break up to 14%, and modulus of elasticity up to 1.39 GPa depending on the exact repeating unit structure. X‐ray diffraction measurements indicate that these polyamides are semicrystalline. Rheology study showed same trend of melt viscosity behavior with different shear rate for all polymers. Water absorption study indicates the hydrophobic nature of the polymer. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis and characterization of 4,5‐bis(4‐fluorobenzoyl)‐1‐methylcyclohexene and its polyethers

A new difluoride 4,5‐bis(4‐fluorobenzoyl)‐1‐methylcyclohexene (DFKK) has been prepared with fumaryl chloride, fluorobenzene, and 2‐methyl‐1,3‐butadiene as starting materials through two steps of reactions. This DFKK monomer undergoes reaction with 2,2‐(p‐hydroxyphenyl)‐iso‐propane (BPA) in the presence of excess anhydrous potassium carbonate in sulfolane to give a high molecular weight reactive poly(ether ketone ketone) (PEKK) that is very soluble in solvents such as chloroform and N,N‐dimethylformamide at room temperature, has glass transition temperature of 182°C, and is easily cast into flexible and bale ivory film with tensile strength of 64 MPa. The 5% weight loss temperature is 407°C. Ring‐closing reaction of PEKK with hydrazine gives cyclized PEKK (CPEKK) with improved thermal stability and reduced solubility. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1866–1871, 2002; DOI 10.1002/app.10454     

Synthesis and characterization of novel poly(amide imide)s based on bis(p‐amidobenzoic acid)‐n‐trimellitylimido‐L‐leucine

N‐Trimellitylimido‐L ‐leucine was reacted with thionyl chloride, and N‐trimellitylimido‐L ‐leucine diacid chloride was obtained in a quantitative yield. The reaction of this diacid chloride with p‐aminobenzoic acid was performed in dry tetrahydrofuran, and bis(p‐amidobenzoic acid)‐N‐trimellitylimido‐L ‐leucine (5) was obtained as a novel optically active aromatic imide–amide diacid monomer in a high yield. The direct polycondensation reaction of the monomer imide–amide diacid 5 with 4,4′‐diaminodiphenylsulfone, 4,4′‐diaminodiphenylether, 1,4‐phenylenediamine, 1,3‐phenylenediamine, 2,4‐diaminotoluene, and benzidine (4,4′‐diaminobiphenyl) was carried out in a medium consisting of triphenyl phosphite, N‐methyl‐2‐pyrolidone, pyridine, and calcium chloride. The resulting novel poly(amide imide)s (PAIs), with inherent viscosities of 0.22–0.52 dL g^?1, were obtained in high yields, were optically active, and had moderate thermal stability. All of the compounds were fully characterized with IR spectroscopy, elemental analyses, and specific rotation. Some structural characterization and physical properties of these new optically active PAIs are reported. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 35–43, 2002; DOI 10.1002/app.10181     

Synthesis and properties of new poly(amide‐imide)s based on 1,3‐bis[4,4'‐(trimellitimido) phenoxy] propane and aromatic diamines

Six new poly(amide‐imide)s 8a–f containing trimethylene moiety in the main chain were synthesized by the polycondensation reactions of 1,3‐bis[4,4'‐(trimellitimido) phenoxy] propane 6 with six different aromatic diamines 7a–f in a medium constituting N‐methyl‐2‐pyrrolidone, triphenylphosphite, CaCl₂, and pyridine as condensing agents. The polycondensation reaction produced a series of novel poly(amide‐imide)s 8a–f in high yields with inherent viscosities between 0.35 and 0.63 dL/g. The resulting poly(amide‐imide)s were characterized by elemental analysis, viscosity measurements, thermal gravimetric analysis (TGA and DTG), solubility tests, and FTIR spectroscopy. 1,3‐Bis[4,4'‐(trimellitimido) phenoxy] propane 6 as a new monomer containing trimethylene moiety was synthesized using a three‐step reaction. At first 1,3‐bis[4,4'‐nitrophenoxy] propane 3 was prepared by the reaction of 4‐nitrophenol 1 with 1,3‐dibromo propane 2 in DMF solution . Then, dinitro 3 was reduced to 1,3‐bis[4,4'‐aminophenoxy] propane 4 by using a solution of sodium sulfite in ethanol. Finally, 1,3‐bis[4,4'‐(trimellitimido) phenoxy] propane 6 was prepared by the reaction of one equivalent diamine 4 with two equivalents of trimellitic anhydride 5 in a mixture of acetic acid‐pyridine (3 : 2). © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis and characterization of new cardo poly(bisbenzothiazole)s from 1,1‐bis(4‐amino‐3‐mercaptophenyl)‐4‐tert‐butylcyclohexane dihydrochloride

A new monomer 1,1‐bis(4‐amino‐3‐mercaptophenyl)‐4‐tert‐butylcyclohexane dihydrochloride, bearing the bulky pendant 4‐tert‐butylcyclohexylidene group, was synthesized from 4‐tert‐butylcyclohexanone in three steps. Its chemical structure was characterized by ¹H NMR, ¹³C NMR, MS, FTIR, and EA. Aromatic poly(bisbenzothiazole)s (PBTs V) were prepared from the new monomer and five aromatic dicarboxylic acids by direct polycondensation. The inherent viscosities were in the range of 0.63–2.17 dL/g. These polymers exhibited good solubility and thermal stability. Most of the prepared PBTs V were soluble in various polar solvents. Thermogravimetric analysis showed the decomposition temperatures at 10% weight loss that were in the range of 495–534°C in nitrogen. All the PBTs V, characterized by X‐ray diffraction, were amorphous. The UV absorption spectra of PBTs V showed a range of λ_max from 334 to 394 nm. All the PBTs V prepared had evident fluorescence emission peaks, ranging from 423 to 475 nm with different intensity. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2000–2008, 2006     

Direct polycondensation of N‐trimellitylimido‐L‐isoleucine with aromatic diamines

N‐Trimellitylimido‐L ‐isoleucine (3) was prepared from the reaction of trimellitic anhydride with L ‐isoleucine [L ‐2‐amino‐3‐methylvalerianic acid or (2S,3S)‐2‐amino‐3‐methyl‐n‐valerinic acid] in an N,N‐dimethylformamide solution at the refluxing temperature. The direct polycondensation reaction of the monomer imide diacid (3) with 1,4‐phenylenediamine, 4,4′‐diaminodiphenylmethane, 4,4′‐diaminodiphenylsulfone, diaminodiphenylether, 1,5‐naphthalendiamine, 2,4‐diaminotoluene, and 1,3‐phenylenediamine was performed in a medium consisting of triphenyl phosphite, N‐methyl‐2‐pyrolidone (NMP), pyridine, and calcium chloride. The polycondensation was performed under two different conditions: in one method, the reaction mixture was heated in an NMP solution at 60, 90, and then 130°C for different periods of time, and in the other method, the reaction mixture was refluxed only for 1 min in the same solvent. The resulting poly(amide imide)s (PAIs), with inherent viscosities of 0.21–0.37 dL/g, were obtained in high yields. All of these compounds were fully characterized by IR spectra, elemental analyses, and specific rotation measurements. Some structural characterizations and physical properties of these new optically active PAIs were examined. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 116–122, 2003