共查询到19条相似文献,搜索用时 187 毫秒
1.
采用物理钝化技术对活性石灰进行处理,研制出一种适用于铁水预处理脱硫用的流态化石灰产品。该产品流动性好、防潮性好、生产成本低,其防潮性可达到冷水浸泡2 h不吸潮溶解,储存期可达一年,产品w(CaO)90%,活性度为350 m L。此产品被应用在太钢铁水预处理复合喷吹脱硫中,很好地解决了石灰粉剂堵枪、下料不畅的难题,在平均铁水量为90 t、初始w(S)=0.028%、石灰粉消耗量平均为3 kg/t、镁粉消耗量平均为1 kg/t的条件下,铁水脱硫率平均可达94.61%,处理后的铁水w(S)平均为0.001 5%。 相似文献
2.
3.
分析了影响钝化镁粉在铁水预处理中利用率的各种因素,通过现场实践数据确定了适合八钢生产条件的基本脱硫参数。通过优化脱硫工艺,提高钝化镁粉的利用率,为八钢铁水预处理应用中深脱硫的研究打下基础。 相似文献
4.
5.
6.
不同铁水脱硫工艺方法的应用效果 总被引:6,自引:1,他引:5
介绍了武钢在提高铁水脱硫预处理能力过程中的基本情况及对KR机械搅拌法、鱼雷罐喷吹法、铁水罐喷吹法处理工艺的优化和降低生产成本等方面达到的效果,介绍了这几种工艺方法使用CaO、CaC2、CaO Mg粒、纯Mg粒等不同脱硫剂及新型脱硫剂试验的情况,分析了各种方法的优缺点。机械搅拌法动力学条件好,较容易实现深脱硫;鱼雷罐喷吹适用于大批量的铁水预处理;纯镁铁水脱硫工艺脱硫剂单耗低,喷吹过程平稳。 相似文献
7.
8.
9.
10.
11.
铁水预处理粉剂用量优化的神经网络模型 总被引:1,自引:0,他引:1
铁水脱硫预处理是炼钢中的关键技术之一.在分析炼钢铁水预处理工艺流程基础上,研究了影响脱硫效果的各种因素,消化、剖析了目前比较通用的铁水脱硫预处理各类控制模型.对于铁水预处理粉剂模型,设计了BP人工神经元网络数学模型,并给出了在系统中的应用方案,使脱硫效果提高8%,符合现场实际生产需求,避免了过吹引起粉剂的浪费. 相似文献
12.
《钢铁研究学报(英文版)》2011,(Z2):113-118
Focused on the hot metal pretreatment process in the torpedo-car and based on the powder injection metallurgy principle, a kinetic model for dephosphorization of high-phosphorus hot metal pretreatment was developed. The validity of this model was verified by comparison between the experimental results in laboratory and the calculated results. The influences of dephosphorization capacity of molten slag and technological conditions on the dephosphorization efficiency were calculated by applying the model. The results show that lower temperatures are favorable to dephosphorization, CaO content in slag should be controlled at about 50%, suitable initial phosphorus content in the hot metal with higher phosphorus contents is about 0.35% by comprehensively considering various factors, slag systems of higher iron oxide content and higher basicity have higher capacity of dephosphorization. 相似文献
13.
A. M. Zborshchik S. V. Kuberskii K. E. Pismarev V. V. Akulov G. Ya. Dovgalyuk 《Steel in Translation》2010,40(1):35-37
Industrial data for the ladle desulfurization of hot metal by the injection of granulated magnesium and a mixture of magnesium
with fluidized lime powder are analyzed. The utilization of magnesium for desulfurization is similar for both methods. Lime
has no significant influence on the efficiency of desulfurization but increases the losses of hot metal with the ladle slag. 相似文献
14.
15.
为了获得最佳的供氧和粉剂消耗与温度的关系。国内某钢厂采用专用炉顶吹氧+喷粉搅拌脱磷工艺为AOD炉提供优质的低磷铁水冶炼不锈钢,实现了新型一步法冶炼不锈钢工艺。生产实践表明,随着喷吹钝化石灰粉和铁皮球用量的增加,脱磷率逐渐升高,当石灰喷吹量为10~12 kg/t、铁皮球消耗量为25.0~37.5 kg/t、供氧量为300~400 m3时,脱磷率在85%以上;脱磷率随着钙氧比的增大而减小,当w(CaO)/w(Fe2O3)为0.8时达到最大值,钙氧比为0.8~1.4时脱磷率大部分在85%以上,钙氧比超过1.4时效果降低。 相似文献
16.
17.
The desulfurization of hot metal by the injection of fluidized lime (≥94% CaO) is analyzed, when the lime consumption is 0.5–19 kg/t of hot metal. That results in 95% desulfurization; the lowest sulfur content in the hot metal is 0.003%. Decrease in sulfur content in the hot metal to 0.005, 0.010, 0.015, 0.020, and 0.025% with different initial sulfur content is observed, with the injection of different quantities of lime. Sulfur content below 0.001% is not observed and not guaranteed. Recommendations are made for optimal desulfurization of hot metal by lime. Their adoption increases the desulfurization, decreases the losses of hot metal and the temperature, and decreases the consumption of materials and the cost of the process. 相似文献
18.
基于改进BP神经网络的铁水预处理终点硫含量预报模型 总被引:1,自引:1,他引:1
铁水预处理脱硫是纯净钢生产中的一项重要任务,其中铁水终点硫含量是反映脱硫站能力和生产效果的重要指标.对梅山钢铁股份有限公司铁水包喷吹CaO Mg粉剂复合脱硫过程,通过采用自适应调整学习率和最大误差学习法对标准BP算法进行了改进,建立了基于改进BP神经网络的铁水预处理终点硫含量预报模型.用梅钢的1154炉数据进行模型训练,经100炉数据现场验证表明,改进的BP算法比标准BP算法预报误差≤0.003%的精度提高28%,有19%的炉次预报值与实际值完全一致,有90%的炉次误差≤0.003%,平均误差为0.0017%.改进的BP算法在铁水预脱硫终点硫含量预报模型应用中获得了更好的使用效果. 相似文献
19.
为了满足生产超低磷钢的预脱磷要求,对不锈钢铁水脱磷工艺进行介绍。在45 t钢包中进行石灰喷粉+吹氧的工业试验,结果表明,在铁水脱硅期达到预期效果(铁水w([Si])≤0.1%)后,铁水脱磷期可实现平均脱磷率大于88%。根据试验数据,分别回归出脱硅期和脱磷期的脱磷率、磷分配比的计算公式。通过添加萤石能够获得较好的铁水脱磷效果,随着铁水硅含量变化,铁水温度、吨钢耗氧量、石灰消耗量、炉渣碱度的增加,铁水的脱磷率明显增加。炉渣w((TFe))的增加对铁水脱磷率的影响不显著。研究认为,目前采用的石灰喷粉+吹氧冶炼进行铁水脱磷处理是行之有效的不锈钢铁水脱磷方法。 相似文献