Implementation of an LED backlight for avionics displays

Abstract— The replacement of conventional light sources used to backlight displays with LEDs is very attractive in avionics. Today's LED technology provides devices suitable to implement display backlight sources but specific requirements need to be satisfied for avionics displays. This paper covers the development of an innovative LED backlight dedicated to avionics displays, realized in a new box geometry in order to generate more than 10,000 cd/m² on a 6 × 5‐in. active area using less than 28 W of power.     

Color performance of an MVA‐LCD using an LED backlight

Abstract— The color performance, including color gamut, color shift, and gamma curve, of a multi‐domain vertical‐alignment (MVA) liquid‐crystal display (LCD) using an LED backlight are calculated quantitatively. Simulation results indicate that an LED backlight exhibits better angular color uniformity and smaller color shifts than a CCFL backlight. Color gamut can be further widened and color shift reduced when using a color‐sequential RGB‐LED backlight without color filters, while the angular‐dependent gamma curves are less influenced using different backlights. The obtained quantitative results are useful for optimizing the color performance and color management of high‐end LCD monitors and LCD TVs.     

Simulated light extraction from a light‐emitting diode integrated with a microlens array

Abstract— Light extraction from InGaN‐based light‐emitting diodes (LEDs) on which microlens arrays were integrated using ray‐tracing methods was simulated. Enhancement of the total light extraction and beam shaping in the forward direction of the output of microlens‐integrated LEDs compared to conventional LEDs were observed. The diameter, curvature radius, and density of the microlens arrays on the LEDs were varied and the optimal conditions for external efficiency was determined.     

A novel lens cap designed for the RGB LEDs installed in an ultra‐thin and directly lit backlight unit of large‐sized LCD TVs

Abstract— The objective of this study is to design a novel cone‐shaped lens cap on LEDs in order to achieve high optical efficiency in an ultra‐thin directly lit RGB LED backlight unit (BLU) for large‐sized LCD TVs. The use of the novel lens cap could play the role of a diffuser, a low light‐efficiency component in a BLU, in order to gain higher efficiency and simultaneously provide satisfactory uniformity in light distribution. The novel cone‐shaped lens is coated with aluminum on the outside surface of the cone for mirroring effects to reflect most of the LED emitted light horizontally and then reflect the light at the BLU boundaries, and then, finally to the output plane. In this way, bright spots on the output plane of the BLU can be avoided, leading to increased uniformity. Simulations were conducted to design and optimize varied aspects of the designed lens and BLU, including the cone angle of the proposed lens and the LED spacing (pitch). To further achieve color balance, a known Genetic Algorithm is used to search for the optimal angular placement of each RGB LED, resulting in better color balance. Finally, a prototype BLU for large‐sized 37‐in. LCD TVs with the proposed lens was built to verify the expected performance.     

A directly addressed monolithic LED array as a projection source

Abstract— Light‐emitting‐diode arrays have been fabricated and demonstrated by several groups in a variety of applications in which structured illumination is desired, such as direct‐view displays and fluorescence detection. State‐of‐the‐art LEDs can achieve a high optical power density, exceeding 40 W/cm². This allows the use of such LEDs, if patterned into an array, as a light and pattern source for projection displays. As a proof of principle, a projection source using a monolithically integrated patterned LED array at a power density of 0.69 W/cm², a source brightness of 21,000,000 cd/m², and a projected brightness of 100,000 cd/m² is reported. It is shown that an improved version of such a display would allow significantly better power consumption and overall system efficiency than permitted by current projection‐display concepts.     

Development of a phosphorescent white OLED with extremely high power efficiency and long lifetime

Abstract— A white OLED device with extremely high power efficiency and long lifetime was developed, in which blue, yellow‐green, and red phosphorescent emitters were used. The performances achieved were 64 lm/W and 10,000 hours of lifetime at an initial luminance of 1000 cd/m² by using a light outcoupling technique. The device also exhibited the good durability important for practical usage. New technologies, such as blue phosphorescent materials and a sophisticated organic layer structure, were applied to the device. Hopefully, these technologies will open the door to the practical use of OLEDs as light sources.     

Sequential‐color LCD based on OCB with an LED backlight

We have fabricated a 13.3‐in. XGA (1024 × 768) TFT sequential‐color liquid‐crystal display using optically compensated birefringency (OCB), illuminated by an LED backlight. We fabricated the sequential‐color display feasible process technology, and examined the performance and potential of a field‐sequential‐color scheme. The display was connected to a laptop computer and examined for flicker.     

Active matrix QD‐LED with top emission structure by UV lithography for RGB patterning

We have developed full colour top emitting quantum dot light‐emitting diode (QD‐LED) display driven by a 176‐ppi active matrix of metal oxide thin‐film transistors. Red, green and blue (RGB) QD‐LED subpixel emission layers are patterned by our original UV photolithography process and materials. We also demonstrate the potential to achieve high resolution such as 528 ppi using this process.     

Vt Compensated voltage‐data a‐Si TFT AMOLED pixel circuits

Abstract— Active‐matrix organic light‐emitting‐diode (AMOLED) displays are now entering the marketplace. The use of a thin‐film‐transistor (TFT) active matrix allows OLED displays to be larger in size, higher in resolutions and lower in power dissipation than is possible using a conventional passive matrix. A number of TFT active‐matrix pixel circuits have been developed for luminance control, while correcting for initial and electrically stressed TFT parameter variations. Previous circuits and driving methods are reviewed. A new driving method is presented in which the threshold‐voltage (V_t) compensation performance, along with various circuit improvements for amorphous‐silicon (a‐Si) TFT pixel circuits using voltage data, are discussed. This new driving method along with various circuit improvements is demonstrated in a state‐of‐the‐art 20‐in. a‐Si TFT AMOLED HDTV.     

Thermal management of edge‐lit wide color gamut backlight for LCD using red laser diodes and cyan LEDs

The color gamut is one of the critical parameters that dictate the image quality of displays. The liquid crystal displays using white color light‐emitting diodes (LEDs) as the backlight, though having been widely employed recently, are not very satisfactory in terms of their color gamut because of the broad spectrum inherent to white LEDs. This prompted the authors to develop improved liquid crystal displays using an edge‐lit wide color gamut backlight that used red laser diodes and cyan LEDs. Generating laser beams with high color purity, the laser diodes are light sources with a significant effect on expanding the color gamut. However, laser diodes, red ones in particular, have unfavorable thermal characteristics. To cope with this shortcoming, the authors clearly defined the restrictive criteria for laying out two kinds of light source on the edge‐lit backlight and made a prototype 55‐type laser backlight for performance evaluation.     

LED‐backlight feedback control system with integrated amorphous‐silicon color sensor on an LCD panel

Abstract— Thin‐film‐transistor liquid‐crystal displays (TFT‐LCDs) have the largest market share of all digital flat‐panel displays. An LCD backlighting system employing a three‐color red‐green‐blue light‐emitting diode (RGB‐LED) array is very attractive, considering its wide color gamut, tunable white point, high dimming ratio, long lifetime, and environmental compatibility. But the high‐intensity LED has problems with thermal stability and degradation of brightness over time. Color and white luminance levels are not stable over a wide range of temperature due to inherent long‐term aging characteristics. In order to minimize color point and brightness differences over time, optical feedback control is the key technology for any LED‐backlight system. In this paper, the feasibility of an optical color‐sensing feedback system for an LED backlight by integrating the amorphous‐silicon (a‐Si) color sensor onto the LCD panel will be presented. To minimize the photoconductivity degradation of a‐Si, a new laser exposure treatment has been applied. The integrated color‐sensor optical‐feedback‐controlled LED‐backlight system minimized the color variation to less than 0.008 Δu'v' (CIE1976) compared to 0.025 for an open‐loop system over the temperature range of 42–76°C.     

Design and fabrication of a micropatterned polydimethylsiloxane (PDMS) light‐guide plate for sheet‐less LCD backlight unit

Abstract— A polydimethylsiloxane (PDMS) light‐guide plate (LGP) having micropatterns with an inverse‐trapezoidal cross section was developed for a sheet‐less LCD backlight unit (BLU). The micropatterned PDMS LGP was fabricated by backside 3‐D diffuser lithography followed by two consecutive PDMS replication processes: photoresist‐to‐PDMS and PDMS‐to‐PDMS replications. The fabricated LGP showed an average luminance of 2878 nits and a uniformity of 73.3% in a 2‐in. backlight module with four side‐view 0.85‐cd LEDs. It also could feasibly be applied to a light source for flexible displays owing to the flexible characteristic of the PDMS itself.     

In‐pixel temperature sensor for high‐luminance active matrix micro‐light‐emitting diode display using low‐temperature polycrystalline silicon and oxide thin‐film‐transistors

We propose an in‐pixel temperature sensor using low‐temperature polycrystalline silicon and oxide (LTPO) thin‐film transistor (TFTs) for high‐luminance active matrix (AM) micro‐light‐emitting diode (LED) displays. By taking advantage of the different off‐current characteristics of p‐type LTPS TFTs and n‐type a‐IGZO TFTs under temperature change, we designed and fabricated a temperature sensor consists of only LTPO TFTs without additional sensing component or material. The fabricated sensor exhibits excellent temperature sensitivity of up to 71.8 mV/°C. In addition, a 64 × 64 temperature sensor array with 3T sensing pixel and integrated gate driver has also been fabricated, which demonstrates potential approach for maxing out the performance of high‐luminance AM micro‐LED display with real‐time in‐pixel temperature monitoring.     

Letter: A new compensation pixel circuit with metal oxide thin‐film transistors for active‐matrix organic light‐emitting diode displays

This paper presents a novel compensation pixel circuit for active‐matrix organic light‐emitting diode displays, in which the coupling effect mask technology is developed to compensate the threshold voltage of driving thin‐film transistor whether it is positive or negative. Twenty discrete compensation pixel circuits have been fabricated by In‐Zn‐O thin‐film transistors process. It is measured that the non‐uniformity of the proposed pixel circuit is significantly reduced with an average value of 8.6%. Furthermore, the organic light‐emitting diode emission current remains constant during 6 h continuous operation, which also confirms the validity of the proposed pixel circuit.     

A 13‐bit universal column driver for various displays of OLED and LCD

A universal column driver is implemented in a 0.13‐µm high‐voltage CMOS process for not only TFT‐LCD but also OLED applications. The proposed column driver employs 13‐bit linear DAC to cover all gamma curves of display applications and address‐based configuration for intra‐ panel interface protocol to support both TV and IT applications. Measured results demonstrate the average voltage of output channels (AVO) is under 1mv, which satisfies 1‐LSB resolution at 18.5V of AVDD.     

Flexible active‐matrix OLED displays: Challenges and progress

Abstract— Organic light‐emitting‐device (OLED) devices are very promising candidates for flexible‐display applications because of their organic thin‐film configuration and excellent optical and video performance. Recent progress of flexible‐OLED technologies for high‐performance full‐color active‐matrix OLED (AMOLED) displays will be presented and future challenges will be discussed. Specific focus is placed on technology components, including high‐efficiency phosphorescent OLED technology, substrates and backplanes for flexible displays, transparent compound cathode technology, conformal packaging, and the flexibility testing of these devices. Finally, the latest prototype in collaboration with LG. Phillips LCD, a flexible 4‐in. QVGA full‐color AMOLED built on amorphous‐silicon backplane, will be described.     

Device‐dependent angular luminance enhancement and optical responses of organic light‐emitting devices with a microlens‐array film

Abstract— By taking the organic emitter apodization calculated from electromagnetic theory as input, the angular luminance enhancement of organic light‐emitting devices (OLEDs) with a microlens‐array film (MAF) can be further evaluated by the ray‐tracing approach. First, the OLEDs of different Alq³ thickness are fabricated and their angular luminance measurements are compared to simulation results. Second, mode analyses for different layers are performed to estimate the enhancement potential of the MAF‐attached devices. Finally, by decreasing the Alq³ thickness, increasing the viewing angle, and attaching the MAF, the EL spectral peak shifts of the OLEDs seem irregular, but the spectral blue shifts induced by the optical structures are all explained by the optical responses (EL spectra divided by the intrinsic PL spectrum). In conclusion, the organic emitters with higher off‐axis‐angle luminous intensity cause lower out‐coupling efficiency but gain higher enhancement after the MAF is attached. With the choices of apodizations and microstructures, the tailored or customized angular radiation patterns can be also made possible.     

A small‐area and low‐power data driver IC using two‐stage DAC with a capacitor array for active matrix flat‐panel displays

A small‐area and low‐power data driver integrated circuit (IC) using a two‐stage digital‐to‐analog converter (DAC) with a capacitor array is proposed for active matrix flat‐panel displays. The proposed data driver IC employs a capacitor array in the two‐stage DAC so as to reduce the DAC area and eliminate the need for a resistor string, which has high‐power consumption. To verify the proposed two‐stage DAC, a 20‐channel data driver IC with the proposed 10‐bit two‐stage DAC was fabricated using a 0.18‐μm complementary metal–oxide–semiconductor process with 1.8 and 6 V complementary metal–oxide–semiconductor devices. The proposed 10‐bit two‐stage DAC occupies only 43.8% of the area of a conventional 10‐bit two‐stage DAC. The measurement results show that the differential nonlinearity and integral nonlinearity are +0.58/?0.52 least significant bit and +0.62/?0.59 least significant bit, respectively. The measured interchannel deviation of the voltage outputs is 8.8 mV, and the measured power consumption of the 20‐channel data driver IC is reduced to 7.1 mW, which is less than half of the power consumed by the conventional one.     

Highly efficient blue organic light‐emitting diode with high color purity using 4,4′‐N,N′‐dicarbazole‐biphyenyl (CBP) doped with 1,4‐bis[2‐(3‐N‐ethylcarbazoryl) vinyl]benzene (BCzVB)

Abstract— An efficient pure blue multilayer organic light‐emitting diode employing 1,4‐bis[2‐(3‐N‐ethylcarbazoryl)vinyl]benzene (BCzVB) doped into 4,4′‐N,N′‐dicarbazole‐biphyenyl (CBP) is reported. The device structure is ITO (indium tin oxide)/TPD (N,N′‐diphenyl‐N,N′‐bis (3‐methylphenyl)‐1,1′biphenyl‐4,4′diamine)/CBP:BCzVB/Alq₃ (tris‐(8‐hydroxy‐quinolinato) aluminum)/Liq (8‐hydroxy‐quinolinato lithium)/Al; here TPD was used as the hole‐transporting layer, CBP as the blue‐emitting host, BCzVB as the blue dopant, Alq₃ as the electron‐transporting layer, Liq as the electron‐injection layer, and Al as the cathode, respectively. A maximum luminance of 8500 cd/m² and a device efficiency of 3.5 cd/A were achieved. The CIE co‐ordinates were x = 0.15, y = 0.16. The electroluminescent spectra reveal a dominant peak at 448 nm and additional peaks at 476 nm with a full width at half maximum of 60 nm. The Föster energy transfer and, especially, carrier trapping models were considered to be the main mechanism for exciton formation on BCzVB molecules under electrical excitation.     

Wide‐bandwidth dielectric resonator antenna with omni‐directional radiation patterns for beam focusing properties in a circular array

Investigation results are presented for a cylindrical dielectric resonator antenna (DRA) with a central airgap, which is excited using a coaxial probe connected to a wire monopole. By selecting the proper values of airgap and monopole heights, a desired impedance bandwidth (S₁₁ ≤ ?10 dB) from 40% to 67% can be achieved. The proposed DRA provides monopole like omni‐directional radiation patterns with low crosspolarization levels throughout the bandwidth. Prototype DRA was fabricated with equal heights of the airgap and monopole and experimentally verified for both the impedance matching and radiation performance. Simulated and measured bandwidths of 67% and 64%, respectively, were obtained with acceptable peak realized gain. The simulated and measured radiation patterns agree well. Furthermore, this DRA is investigated for beam focusing properties when implemented in a circular array consisting of four‐elements on a circular finite ground plane. © 2013 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:92–101, 2014.