Experimental study of a hydrogen-air rotating detonation engine with variable air-inlet slot

Rotating detonation engines have attracted considerable attentions in recent years. In this study, the experiments of initiating rotating detonation waves were performed on a H₂/air rotating detonation wave with the variable air-inlet slot. The results showed that the stability of detonation-wave pressure and velocity both initially increased and then decreased with the increase of slot width, and it could improve the stability of detonation-wave velocity via increasing the equivalence ratio. The intensity of reflected wave was strong for the tests of d = 0.5 mm, which leaded to the advance ignition of fresh mixture and a velocity deficit reaching up to 20%. The strong interaction between air plenum and combustor and bad mixing effect may be the reasons of forming unstable detonation wave for the tests of large-scale slots. The air-inlet slot of d = 1 mm, which got a best experiment results relative to other tests, had a wide equivalence-ratio scope to produce stable detonation wave.     

Hydrogen-fueled detonation ramjet model: Wind tunnel tests at approach air stream Mach number 5.7 and stagnation temperature 1500 K

The mode of continuous spinning detonation (CSD) combustion of hydrogen in the annular combustor of a model of a hydrogen-fueled detonation ramjet under conditions of approach air stream Mach number 5.7 and stagnation temperature 1500 K is registered experimentally in a short-duration (pulsed) wind tunnel at the overall air-to-hydrogen equivalence ratio (ER) ranging from 0.7 to 1.4. The maximum values of thrust and specific impulse of the ramjet model are attained at ER = 1.25 and are estimated as 1550 N and 3300 s, respectively. At 1.4 < ER < 1.6, the mode of longitudinally pulsating detonation (LPD) combustion is registered with somewhat lower values of thrust and specific impulse.     

Experimental study of a hydrogen-air rotating detonation combustor

The rotating detonation engine can generate continuous thrust via one or more detonation waves. In this study, rotating detonation experiments were performed on a combined structure which included a rotating detonation combustor (RDC) and a centrifugal compressor. Air, which functioned as an oxidiser, was obtained from the environment by the compressor, and hydrogen, which was used as fuel, was provided by the supply system. The propagation velocity of the rotating detonation wave (RDW) reached 81% of the Chapman–Jouguet value in experiments. With the increase of the air-injection area, the detonation-wave pressure increased, but the stability decreased. An air-injection area of 495 mm² was selected for long-duration experiments, and the frequency of the RDW ranged from 3 to 3.5 kHz. Through the self-adjustment of the combined structure, the air pressure ultimately reached a stable state after a certain period of time, and a stable detonation wave was formed in the RDC.     

Effects of a turbine guide vane on hydrogen-air rotating detonation wave propagation characteristics

The rotating detonation engine is a new machine that can generate thrust via continuous rotating detonation waves (RDWs). In this study, experiments were performed on a structure combining a rotating detonation combustor (RDC) and a turbine guide vane to investigate the propagation characteristic of hydrogen-air RDW. The results showed that the velocity of detonation wave initially increased and then decreased with the increase of equivalence ratio, and it got a velocity of 84% Chapman-Jouguet value. The velocity of detonation wave generally rose by 4.31% comparing with the no guide vane tests, while the scope of steady-operation state became narrow. The oscillation pressure was reduced by 64% after passing through the guide vane, and the magnitude of pressure was only 0.4 bar at the guide vane exit. Meanwhile, part of the shock wave was reflected back to combustor resulting in some small pressure disturbances, and the propagation mode of reflected wave was related to the propagation direction of RDW.     

Experimental investigation on propagation characteristics of liquid-fuel/preheated-air rotating detonation wave

The rotating detonation combustor can be applied to the turbine engine to develop into a new power device, and the liquid-fuel/air rotating denotation has important research significance for engine applications. In this research, the propagation characteristics of liquid-fuel/air rotating detonation wave were experimentally investigated. A hydrocarbon mixture—liquid gasoline was employed for the fuel, the oxidizer was high-temperature air preheated by a hydrogen-oxygen heater, and the rotating detonation wave was initiated via a hydrogen-oxygen pre-detonator. The effects of the equivalence ratio, ignition pressure, and air total temperature on the propagation characteristics of the liquid-fuel rotating detonation wave were analyzed. The liquid-fuel/air continuous rotating detonation wave can be successfully obtained with a single-wave mode, and the velocity and peak pressure of the rotating detonation waves increase as the equivalence ratio increases. As the detonation-wave pressures at the outlet of the pre-detonator increase, the establishment time of the rotating detonation wave gradually decreases, and the average establishment time is 4.01 ms. Stable rotating detonation waves are obtained with the air total temperature of 600–800 K, but the intensity of the detonation wave has a large deficit due to some instabilities.     

The effect of premixed stratification on the wave dynamics of a rotating detonation combustor

Typical injection schemes of rotating detonation combustors inject fuel locally into the combustion channel, creating stratified fuel-rich and fuel-lean mixing regions. In this study, premixed hydrogen and air rotating detonations are explored in a rotating detonation combustor through premixing part of the fuel into the oxidizer flow. The objective is to investigate the effect of premixing on the operation of the combustor. Three premixing schemes are examined where the detonation wave speeds are analyzed. The results show that in premixing, the fuel-lean regions became more favorable for continuous detonation propagation when premixed with the bypass fuel, resulting in higher detonation wave speeds. This phenomenon is shown to be independent of the global fuel-air equivalence ratio and the amount of fuel premixed into the oxidizer. As such, combustor performance and the operational regime could be improved with lean hydrogen premixing amounts in the main flow oxidizer.     

Continuous detonation combustion of ternary “hydrogen–liquid propane–air” mixture in annular combustor

Experiments are performed on continuous detonation combustion of ternary hydrogen–liquid propane–air mixture in a large-scale annular combustor 406 mm in outer diameter with an annular gap of 25 mm. Liquid propane is fed into the combustor at the time when sustained continuous-detonation combustion of hydrogen–air mixture is attained therein. Mass flow rates of hydrogen, propane and air in the experiments ranged from 0.1 to 0.5 kg/s (hydrogen), 0.1 to 0.5 kg/s (propane), and 5 to 12 kg/s (air). Continuous-detonation combustion of liquid propane in air is obtained for the first time due to addition of hydrogen rather than due to enrichment of air with oxygen. Combustor operation with a single continuously rotating detonation wave (DW) for about 0.1 s has been obtained when the flow rates of propane and air remained constant while the flow rate of hydrogen was rapidly decreasing.     

Experimental and numerical research on rotating detonation combustor under non-premixed conditions

In order to investigate the formation process and propagation characteristics of detonation wave, developing process of detonation wave from initiation to stable detonation formation under non-premixed conditions has been studied by experiments and numerical simulation. The results show that when mass flow rates of air and hydrogen are 158.957 g/s and 2.728 g/s respectively, stable detonation can be formed in the combustor. Due to the lower inlet pressure, there is an unstable stage in combustor before the stable detonation is formed. Reducing the air pressure will increase the lowest detonation limit of combustor and lead to flame-out and re-initiation in the combustor. The propagation direction of detonation wave may change after re-initiation. Non-premixed intake structure lead to the inconsistency of rotating detonation combustion fluid in the radial direction. Moreover, peak pressure appears near the outer wall, while peak temperature appears near the inner wall.     

Amplitude modulated instability in reactants plenum of a rotating detonation combustor

The pronounced interest in rotating detonation combustors (RDC) in recent years has witnessed the investigation of multiple facets of the combustor, like reactants, injection schemes and combustor geometry. The issue of instabilities in RDCs is a nascent field, and requires both the identification, and the subsequent explanation of different instability mechanisms. In particular, we are concerned with the low frequency instability exhibited by the detonation wave. This is attributed to two different types of low frequency instabilities—amplitude and frequency modulated—that are discovered in the air plenum of an RDC, and subsequently discussed. The occurrence of these instabilities is observed to depend on the fuel injection scheme used and the air flow rates through the combustor. The amplitude modulated instability in the air inlet is spatially varying, and rotates in a direction opposite to the direction of the detonation wave. At higher air flow rates, and thus higher pressure ratios across the air injection, this instability disappears. A preliminary hypothesis is proposed to explain this amplitude modulation.     

Research on H2/Air rotating detonation in the hollow chamber with double injection

In order to investigate the relationship between high frequency tangential instability and continuous rotating detonation, series of H₂/Air rotating detonations are experimentally achieved in the hollow chamber with double injection sections. In the center part, gaseous H₂ and air injected by co-axial injector. Near the outer wall, the same propellants are injected in the form of slit-orifice collision. By keeping the total air mass flow rate approximately constant, varying the mixture of the inner and outer injection, series experiments are conducted in the test model with or without Laval nozzle. The results verify the possibility of rotating detonation in the hollow chamber with co-axial injector. To clarify the relationship between continuous rotating detonation and high frequency tangential combustion instability, the intrinsic frequencies of the test model are captured to be compared with propagation frequencies of detonation waves. The results show that they are close to each other when enough propellant assembled near the outer wall. In the combustor, the flame direction in constant pressure mode can change itself into rotating direction spontaneously. The results indicate that rotating detonation is an implication to high frequency tangential instability.