Uptake of Pb2+ Using N-Vinyl Imidazole Based Uniform Porous Hydrogels

The uniform porous and continuous phase lead (II) adsorbent hydrogel, was prepared by copolymerizing 2-hydroxyethyl methacrylate (HEMA), acrylic acid (AAc), and N,N′-methylenebisacrylamide (MBAAm), with n-vinyl imidazole (VIM). A series of hydrogels, including different ratios of VIM, were prepared by photopolymerization and characterized. The influence of the uptake conditions such as pH, functional monomer percent, contact time, initial feed concentration, and foreign metal ions on the metal ion binding capacity of hydrogel, were also tested. The selective chelation of heavy metal ions from synthetic wastewater was also studied. The affinity order on molar basis was observed as follows: Pb (II) > Zn (II) > Cd (II). Chelation behavior of heavy metal ions could be modelled using both the Langmuir and Freundlich isotherms and it was seen that the Langmuir isotherm model was the best fit for the adsorption of Pb (II) ions in P(VIM/AAc/HEMA) hydrogel. Moreover, the limits of detection and the quantification values were determined. Regeneration of the hydrogels was easily performed with 1 M HCl and the same hydrogel can be reused five times almost without any loss of adsorption capacity. All these features make P(VIM/AAc/HEMA) hydrogels potential candidate adsorbent for heavy metal removal.     

Poly (acrylic acid-co-acryloyl tetrasodium thiacalix[4]arene tetrasulfonate) grafted dextrin: new supper metal ion adsorbing hydrogels

Dextrin as a biodegradable natural polymer has hydrophilic nature that capable to increase the swelling properties and biodegradability of the synthetic hydrogels. This study describes the synthesis of a poly (acrylic acid-co-acryloyl tetrasodium thiacalix[4]arene tetrasulfonate) grafted dextrin superabsorbent hydrogels (ADA) via solution polymerization. The effects of acryloyl tetrasodium thiacalix[4]arene tetrasulfonate (ACSTCA) dose (20–60) on swelling properties of the hydrogels were studied. The synthesized hydrogels were characterized by FTIR, TGA, DMTA and rheometry. The metal ion removal capacity of the gels was investigated by atomic absorption for Cd²⁺, Pb²⁺, and Hg²⁺. The tendency of metal ions adsorption decreased in the order of Pb²⁺>Cd²⁺>Hg²⁺. The effect of key operating parameters including ACSTCA content, contact time, adsorbent dosage, solution pH, and crosslinker density was experimentally studied on Pb²⁺ adsorption from aqueous solution. The equilibrium data was analyzed using Langmuir and Freundlich adsorption isotherms. Our experimental data are in best agreement with Freundlich isotherms, and adsorption of metal cation onto hydrogel followed a pseudo second-order kinetic model. According to the thermodynamic parameters, the adsorption of Pb²⁺ occurred spontaneously. The hydrogels could be regenerated after releasing heavy metal ions, and reused 5 times with less than 7 % loss of adsorption capacity.     

Interaction of stevensite with Cd2+ and Pb2+ in aqueous dispersions

The experimental process of adsorption of Pb(II) and Cd(II) onto clay mineral is studied here in order to evaluate the capacity for removal for these two heavy metal ions. This study is performed under various conditions such as initial solution pH, chemical clay modification conditions, initial metal ion concentration and contact time. The experimental isotherm data are analysed using Temkin, Langmuir and Freundlich equations and it is shown that models produce comparable equilibrium correlation results. The isotherm curves show very clearly the selectivity of the clay for the lead ions but also significant amounts of cadmium are removed as well. Adsorption kinetics data were tested using pseudo-first-order and Intraparticle diffusion models. Adsorption mechanism studies revealed that the process was complex and followed both surface adsorption and particle diffusion. The rate-controlling parameters and diffusion coefficients were determined using the Crank and McKay diffusion models. It was found that the adsorption occurs through film diffusion and the particle diffusion becomes the rate-determining step for each metal ion.     

松果对废水中Cu~(2+)、Pb~(2+)、Zn~(2+)的吸附特性研究

以松果作为吸附剂进行了去除废水中Cu2+、Pb2+、Zn2+的吸附及解吸试验,研究了溶液pH值、吸附剂投加量、反应时间、溶液初始浓度对吸附效果的影响,以及不同pH值对达到吸附平衡的松果的解吸影响。结果表明:当pH值为5.0～5.5,Cu2+、Pb2+、Zn2+初始质量浓度约为25 mg/L时,吸附剂的最佳投加量分别为3、1.5、3 g/L,去除率分别为55.32%、86%、39.96%。3种重金属离子的吸附动力学方程符合Lagergren准二级动力学方程,R2均大于0.998。等温吸附研究表明:Freundlich方程能较好地描述Cu2+的等温吸附过程,Langmuir方程则能更好地描述Pb2+和Zn2+的吸附过程,用Langmuir方程拟合等温吸附数据得出松果对Cu2+、Pb2+、Zn2+的最大吸附量分别为9.10、31.65和9.60 mg/g。强酸是一种理想的Cu2+和Zn2+解吸剂。     

Enhanced adsorption of heavy metal ions onto simultaneous interpenetrating polymer network hydrogels synthesized by UV irradiation

Simultaneous interpenetrating polymer network (IPN) hydrogels have been prepared by UV-initiated polymerization of a mixture of 2-acrylamido-2-methyl-1-propansulfonic acid (AMPS) and triethylene glycol divinyl ether (DVE-3) with enhanced adsorption properties for heavy metal ion removal. The swelling ratio of the IPN hydrogels determined by gravimetric method increased with the AMPS content in the formulation. The IPN hydrogels were used to remove heavy metal ions from aqueous solution. The effects of pH value of the feed solution and AMPS content in the formulation on the adsorption capacity were investigated. The results indicated that the adsorption capacity increased with the pH values and AMPS content in the formulation. Furthermore, the synergistic complexation of metal ions with two polymer networks in the IPN was found in the adsorption studies. The adsorption isotherm of the IPN hydrogels can be well fitted to the Freundlich model. The adsorption kinetics on IPN hydrogels clearly followed an initial transport-controlled adsorption process, but transited to an attachment-controlled adsorption kinetics in the later stage. Thermodynamic parameters such as the Gibbs free energy (ΔG°), enthalpy (ΔH°), and entropy (ΔS°) for the adsorption were estimated. Results suggested that the adsorption process was a spontaneous, exothermic process that had positive entropy.     

Hydrogels with Acid Groups for Removal of Copper(II) and Lead(II) Ions

Acrylamide-maleic acid (AAM-MA) hydrogels having high acid group content prepared with different maleic acid ratios were used for the removal of Cu(II) and Pb(II) ions from aqueous solutions in competitive and noncompetitive conditions. The effects of pH, time, and initial metal ion concentration on the metal ion adsorption capacity were investigated. The adsorption isotherm models were applied on experimental data and it is shown that the Freundlich equation was the best model for Cu(II) ion while the Langmuir isotherm model was the best one for Pb(II) ion. The stability constants of acrylamide-maleic acid hydrogel-Cu(II) and Pb(II) complexes were also determined by van den Berg/Ruzic transformation, and K values obtained were 1.60 × 10³ and 1.81 × 10³ for Cu(II) and Pb(II) ions, respectively. The experiments under competitive conditions showed that the hydrogels prefered Pb(II) ion and this preference increased with increasing of carboxylic acid group content (AGC) of polymers. It is stated that these hydrogels can be regenerated efficiently (>95%) and used repeatedly.     

Investigation of zinc(II) adsorption on Cladophora crispata in a two‐staged reactor

In this study, the adsorption of zinc(II) ions on Cladophora crispata, a green alga, was studied with respect to initial pH, temperature, initial metal ion and biomass concentration in order to determine the optimum adsorption conditions. Optimum initial pH values for zinc(II) ions were found to be 5.0 at optimum temperature, 25 °C. The initial adsorption rates increased with increasing initial zinc(II) ion concentration up to 100 mgdm⁻³. The Freundlich and Langmuir adsorption isotherms were developed at various initial pH and temperature values. Then, the adsorption of zinc(II) ions to C crispata was investigated in a two‐staged mixed batch reactor. The residual metal ion concentrations (C_eq) at equilibrium at each stage for a given quantity of dried algae (X_o)/volume of solution containing heavy metal ion (V_o) ratio were calculated by using Freundlich and Langmuir isotherm constants. It was observed that the experimental biosorption equilibrium data for zinc(II) ions are in good agreement with those calculated using both Freundlich and Langmuir models. The adsorbed zinc(II) ion concentration increased with increasing X_o/V_o ratios while the adsorbed metal quantities per unit mass of dried algae decreased. © 2000 Society of Chemical Industry     

Comparative Study of Zn2+, Cd2+, and Pb2+ Removal From Water Solution Using Natural Clinoptilolitic Zeolite and Commercial Granulated Activated Carbon. Equilibrium of Adsorption

Abstract

The aim of this work is to study the effectiveness of regional, low-cost natural clinoptilolitic zeolite tuff in heavy metal ions removal from aqueous solution, through comparative study with commercial granulated activated carbon. The equilibrium of adsorption of Cd²⁺, Pb²⁺, and Zn²⁺ on both adsorbents have been determined at 25, 35, and 45°C in batch mode. The granulated activated carbon has shown around three times higher adsorption capacity for Cd²⁺ and Zn²⁺ than natural zeolite, and almost the same adsorption capacity for Pb²⁺ as the natural zeolite. The metal ion selectivity series Pb²⁺ > Cd²⁺ > Zn²⁺, on a mass basis, has been obtained on both adsorbents. The Langmuir and Freundlich model have been used to describe the adsorption equilibrium. The thermodynamic parameters were calculated from the adsorption isotherm data obtained at different temperatures. The study of the influence of the acidity of the metal ion aqueous solution has shown an increase of metal ion uptake with increase of the pH. The sorption mechanism of Cd²⁺, Pb²⁺, and Zn²⁺ on natural zeolite changes from ion-exchange to ion-exchange and adsorption of metal-hydroxide with increase of the pH from 2 to 6 (and 7 for Zn²⁺). The preliminary cost calculation, based on adsorbents maximum adsorption capacity and their price, have revealed the potential of natural zeolite as an economic alternative to the granulated activated carbon in the treatment of heavy metal polluted wastewater.     

Heavy metals adsorption on some iminodiacetate chelating resins as a function of the adsorption parameters

The adsorption properties of some novel chelating resins (CRs) bearing iminodiacetate groups for removal of heavy metal ions like: Cu(II), Co(II) and Ni(II) from aqueous solutions comparative with the commercial resin Amberlite IRC-748 have been studied in this work by a batch equilibrium technique. Quantitative analysis for adsorption was conducted using UV–vis spectroscopy to investigate the kinetics, adsorption isotherm and thermodynamics of the removal process considering equilibration time, pH, metal ion concentration and temperature as controlling parameters. The metal adsorption capacities, at pH 5, were in the order Cu(II) > Ni(II) > Co(II), for both the CR with 10 wt.% DVB (CR-10) and the commercial resin Amberlite IRC-748. The adsorption capacities on CR-10 were higher for Ni(II) and Co(II) ions, but lower for Cu(II) ions compared with Amberlite IRC-748. Both Freundlich and Langmuir isotherms well fitted on the adsorption results of Cu(II), Ni(II) and Co(II) ions on all iminodiacetate resins.     

Microwave preparation and properties of O-crosslinked maleic acyl chitosan adsorbent for Pb2+ and Cu2+

A novel chitosan-based adsorbent (CCTM) was prepared by the reaction of epichlorohydrin O-crosslinked chitosan with maleic anhydride under microwave irradiation. The chemical structure of this polymer was characterized by infrared spectroscopy and X-ray diffraction analyses. The effects of various variables such as degree of substitution, adsorption time, initial metal ion concentration, solution pH, and temperature, on the adsorption of Pb²⁺ and Cu²⁺ by CCTM were investigated. The results demonstrate that the microwave irradiation can remarkably enhance the reaction. CCTM has higher adsorption capacity than chitosan. The maximum adsorption capacities for Pb²⁺ and Cu²⁺, with initial concentrations of 0.02 mol L⁻¹ at pH 5, are 246.3 and 132.5 mg g⁻¹, respectively. The adsorbent can be recycled. These results have important implications for the design of effective chitosan-based adsorbents in the removal of heavy metal ions from wastewaters. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

A Novel pH-Responsive p(AAm-co-METAC)/MMT Composite Hydrogel: Synthesis,Characterization and Its Absorption Performance on Heavy Metal İons

In this study, the preparation and characterization of the novel pH-sensitive poly(acrylamide-co-2-methacryloyloxy)ethyltrimethyl ammonium chloride)/montmorillonite (p(AAm-co-METAC)/MMT) composite superabsorbent hydrogels and their selective metal absorbtion properties were investigated. The adsorption of metal ions is highly dependent on the initial feed concentration, contact time, pH of the metal solution and adsorbent doses. The results were analyzed both by the Langmuir and Freundlich isotherms and the adsorption is found to follow pseudo-second-order kinetics. The adsorption capacity followed the order Zn²⁺ > Ni²⁺ > Cu²⁺ > Pb²⁺ and the maximum adsorption capacities of them were ～320, 285, 240 and 120 (mg g^?1), respectively.     

Cu2+ removal from aqueous solution by modified chitosan hydrogels

BACKGROUND: The adsorption of Cu²⁺ from aqueous solution using crosslinked chitosan hydrogels impregnated with Congo Red (CR) by ion‐imprint technology was systematically investigated with particular reference to the effects of contact time, pH, and initial concentration on adsorption. RESULTS: The adsorption capacity of the crosslinked chitosan without impregnation was only 68.68 mg g^?1 for Cu²⁺. However, the adsorption capacity increased from 77.42 (without imprint ion) to 84.54 mg g^?1 (imprint ion content 0.5 mmol) after the chitosan was impregnated with a ratio of 1/12 of CR to chitosan. The as‐prepared adsorbents were found to be pH‐dependent and the process of adsorption agreed well with the Freundlich isotherm. The loaded adsorbents could be regenerated and reused without the appreciable loss of capacity. CONCLUSION: Chitosan hydrogels impregnated with CR showed higher Cu²⁺ adsorption capacities compared with those prepared conventionally without imprint ion, and thus developed a good approach to increase Cu²⁺ adsorption efficiency in the treatment of waste‐water. Copyright © 2012 Society of Chemical Industry     

Investigation of adsorption of lead,mercury and nickel from aqueous solutions onto carbon aerogel

Recently a new form of activated carbon has appeared: carbon aerogel (CA). Its use for the removal of inorganic (and especially metal ions) has not been studied. In the present study, the adsorption of three metal ions, Hg(II), Pb(II) and Ni(II), onto carbon aerogel has been investigated. Batch experiments were carried out to assess adsorption equilibria and kinetic behaviour of heavy metal ions by varying parameters such as agitation time, metal ions' concentration, adsorbent dose and pH. They facilitated the computation of kinetic parameters and maximum metal ion adsorption capacities. Increasing the initial solution pH (2–10) and carbon concentration (50–500 mg per 50 cm³) increases the removal of all three metal ions. A decrease of equilibrium pH with an increase of metal ion concentration led us to propose an adsorption mechanism by ion exchange between metal cations and H⁺ at the carbon aerogel surface. Carboxylic groups are especially involved in this adsorption mechanism. Langmuir and Freundlich isotherm models were used to analyse the experimental data of carbon aerogel. The thermodynamics of the metal adsorption was also investigated for the practical implementation of the adsorbent. The sorption showed significant increase with increase of temperature. Kinetics models describing the adsorption of Hg(II), Pb(II) and Ni(II) ions onto carbon aerogel have been compared. Kinetics models evaluated include the pseudo‐first order and second order model. The parameters of the adsorption rate constants have been determined and the effectiveness of each model assessed. The result obtained showed that the pseudo‐second order kinetic model correlated well with the experimental data and better than the pseudo‐first order model examined in the study. Mass transfer coefficients obtained can be useful in designing wastewater treatment systems or in the development of environmental technologies. Copyright © 2005 Society of Chemical Industry     

Heavy metals uptake from aqueous solutions and industrial wastewaters by humic acid-immobilized polymer/bentonite composite: Kinetics and equilibrium modeling

This study explored the feasibility of utilizing a novel adsorbent, humic acid-immobilized-amine-modified polyacrylamide/bentonite composite (HA-Am-PAA-B) for the adsorption of Cu(II), Zn(II) and Co(II) ions from aqueous solutions. The FTIR and XRD analyses were done to characterize the adsorbent material. The effects of pH, contact time, initial adsorbate concentration, ionic strength and adsorbent dose on adsorption of metal ions were investigated using batch adsorption experiments. The optimum pH for Cu(II), Zn(II) and Co(II) adsorption was observed at 5.0, 9.0 and 8.0, respectively. The mechanism for the removal of metal ions by HA-Am-PAA-B was based on ion exchange and complexation reactions. Metal removal by HA-Am-PAA-B followed a pseudo-second-order kinetics and equilibrium was achieved within 120 min. The suitability of Langmuir, Freundlich and Dubinin-Radushkevich adsorption models to the equilibrium data was investigated. The adsorption was well described by the Langmuir isotherm model. The maximum monolayer adsorption capacity was 106.2, 96.1 and 52.9 mg g^?1 for Cu(II), Zn(II) and Co(II) ions, respectively, at 30 °C. The efficiency of HA-Am-PAA-B in removing metal ions from different industry wastewaters was tested. Adsorbed metal ions were desorbed effectively (97.7 for Cu(II), 98.5 for Zn(II) and 99.2% for Co(II)) by 0.1 M HCl. The reusability of the HA-Am-PAA-B for several cycles was also demonstrated.     

Recovery of heavy metals from aqueous solution by using radiation crosslinked poly(vinyl alcohol)

Crosslinked poly(vinyl alcohol) (PVA) and PVA/acrylic acid hydrogels, prepared by γ‐irradiation, were used in the removal of heavy metals from aqueous solution. Comparative studies of the properties of the two hydrogels were made. The application of the prepared hydrogels as adsorbent materials for Cu²⁺, Co²⁺, and Ni²⁺ from aqueous solution was studied. The chemical and physical properties of the hydrogels, before and after adsorption of the heavy metal ions, were investigated by means of thermogravimetric analysis, differential scanning calorimetry, and scanning electron microscopy. The efficiency of such hydrogels for the recovery of metal ions was determined by atomic absorption and UV spectroscopic analysis. The effect of changing pH on the metal uptake was also studied. It was found that the prepared hydrogels have a substantial ability to adsorb metal ions from their solution. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1649–1656, 2004     

Removal of Cu2+ Ions from Aqueous Solutions by Starch-Graft-Acrylic Acid Hydrogels

Gelatinized starch was prepared by constantly stirring a mixture of starch and water at 95°C for 1 hour. Starch-graft-acrylic acid (S-g-AA) hydrogels were prepared by grafting acrylic acid (AA) [monomer/starch (w/w) 0.5–1.5] onto gelatinized starch with ceric ammonium nitrate as initiator under nitrogen atmosphere. The surface morphology of samples was studied using a scanning electron microscope (SEM). The hydrogels were evaluated for the removal of Cu²⁺ ion from aqueous solutions at different pH. The concentration of Cu²⁺ ion in aqueous solution was kept constant at 4 mmol/L. The metal ion removal capacities changed depending on treatment time, initial pH of the solution, and monomer/starch (w/w) ratio of the S-g-AA hydrogels. Cu²⁺ ion removal capacities were determined by atomic absorption spectrometer (AAS).     

Determination of the competitive adsorption of heavy metal ions on poly(n‐vinyl‐2‐pyrrolidone/acrylic acid) hydrogels by differential pulse polarography

Poly(N‐vinyl‐2‐pyrrolidone) and poly(N‐vinyl‐2‐pyrrolidone/acrylic acid) hydrogels were prepared by gamma irradiation for the removal of heavy metal ions (i.e., lead, copper, zinc, and cadmium) from aqueous solutions containing different amounts of these ions (2.5–10 mg/L) and at different pH values (1–13). The observed affinity order in adsorption of these metal ions on the hydrogels was Zn(II) > Pb(II) > Cu(II) > Cd(II) under competitive conditions. The optimal pH range for the heavy metal ions was from 7 to 9. The adsorption of the heavy metal ions decreased with increasing temperature in both water and synthetic seawater conditions. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2013–2018, 2003     

Adsorption of some heavy metal ions from aqueous solutions on Nafion 117 membrane

Nafion 117 membrane was investigated for the removal of Ni(II), Co(II), Pb(II), Cu(II) and Ag(I) metal ions from their synthesized aqueous solutions. The different variables affecting the adsorption capacity of the membrane such as contact time, initial metal ion concentration in the feed solution, pH of the sorption medium and temperature of the solution were investigated on a batch sorption basis. The affinity of Nafion 117 membrane towards heavy metal ions was found to increase in the sequence of Cu(II), Ni(II), Co(II), Pb(II), and Ag(I) with adsorption equilibrium achieved after 30 min for all metal ions. Among all parameters, pH has the most significant effect on the adsorption capacity, particularly in the range of 3.1-5.9. The variation of temperature in the range of 25-65 °C was found to have no significant effect on the adsorption capacity. Nafion 117 membrane was found to have high stability combined with repeated regeneration ability and can be suggested for effective removal of heavy metal ions such as Cu(II), Ni(II) and Co(II) from aqueous solutions.     

Removal of heavy metal ions by dithiocarbamate-anchored polymer/organosmectite composites

In this study, the dithiocarbamate-anchored polymer/organosmectite composites were prepared for the removal of heavy metal ions (lead, cadmium and chromium) from aqueous media containing different amounts of these ions (50–750 ppm) and at different pH values (2.0–8.0). Initially, the modification of the natural smectite minerals was performed by treatment with quartamin styrene and chloromethylstyrene. Then, modified smectite nanocomposites were reacted with carbondisulfide, in order to incorporate dithiocarbamate functional groups into the nanolayer of organoclay. The dithiocarbamate-anchored nano-composites have been characterized by FTIR and used in the adsorption–desorption process. The maximum adsorptions of heavy metal ions onto the dithiocarbamate-anchored polymer/organosmectite composites from their solution was 170.7 mg g^− 1 for Pb(II); 82.2 mg g^− 1 for Cd(II) and 71.1 mg g^− 1 for Cr(III). Competition between heavy metal ions (in the case of adsorption from mixture) yielded adsorption capacities of 70.4 mg g^− 1 for Pb(II); 31.8 mg g^− 1 for Cd(II) and 20.3 mg g^− 1 for Cr(III). Desorption of the heavy metal ions from composite was studied in 0.5 M NaCl and very high desorption rates, greater than 93%, were achieved in all cases. Adsorption–desorption cycles showed the feasibility of repeated uses of this nanocomposite.