A low,particle‐sized,nonporous support for enzyme immobilization: Uniform poly(glycidyl methacrylate) latex particles

The uniform and nonporous poly(glycidyl methacrylate) (poly(GMA)) latex particles, 1.7 μm in size, were first tried as a support in enzyme immobilization. For this purpose, α‐chymotrypsin (CT) was selected as the model enzyme. The low particle size and nonporous character of the selected support allowed to carry out the enzyme–subtrate interaction on a sufficiently large surface area (3.36 m²/g) and in the absence of intraparticular diffusion limitations. This property is particularly important when the immobilized CT is used for the substrates with high molecular weights (i.e., proteins). The latex particles were synthesized by dispersion polymerization of GMA. The reactive character of poly(GMA) allowed the direct attachment of primary amine groups onto the particles. Confocal laser scanning microscopy (CLSM) showed that primary amine groups were preferentially located on the particle's surface. Hence, the selected enzyme, CT was immobilized on the surface of nonporous particles via glutaraldehyde activation. For CT‐immobilized poly(GMA) particles, the maximum activity (r_m) and Michealis constant (K_m) were found to be 17.2 μmol/mg CT min and 121.6 μm, respectively. No significant loss was observed in the activity of immobilized CT, during the course of experiments. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 818–824, 2006     

Polymer-polymer interaction parameters in the ternary system polystyrene/poly(α-methyl styrene)/n-butyl chloride

The polymer-polymer interaction parameter χ′12, for the polystyrene/poly(α-methyl styrene)/n-butyl chloride ternary system, has been determined from activity coefficients of the solution measured using piezoelectric vapour sorption methods in the temperature range 30°–60°C. (These measurements where carried out in the concentration range 0.06 < ψ₀ < 0.26, where ψ is the segment fraction of the solvent). The values of χ¹⁰₁₂ extrapolated to zero solvent concentration over the range 30°–60°C, are large and negative (−0.2 to −0.9) χ¹₁₂ was found to increase with ψ₀. The negative values of χ¹₁₂ in this work are in agreement with the T_g in the polystyrene

Full-size image (1K)

M_w = 9.09 × 10⁴) blends on the point of blend compatibility. The polymer-polymer interaction parameters obtained in this work are discussed by taking into account the high susceptibility of polymers in the glassy state to solution of organic solvents.     

Partial oxidation of methane to synthesis gas over corundum supported mixed oxides: One channel studies

Catalytic partial oxidation of methane (POM) over the monolithic catalyst LaNiO_x/CeO₂–ZrO₂/α-Al₂O₃ has been studied. Experiments were conducted with one channel of a monolith at a varied channel length, contact time (1–6 ms) and temperature using the diluted gas mixture (1% CH₄ + 0.5% O₂ in He). At increasing temperature and contact time, CO selectivity rises within the whole temperature range whereas the contact time dependence of H₂/CO ratio varies with the temperature. These results support the POM reaction scheme including primary formation of CO and H₂ followed by their oxidation in the presence of gas-phase O₂. Steam and dry methane reforming reactions occur in the part of monolithic channel where oxygen is absent, thus increasing syngas yield.     

Synthesis of Reactive Sulfur Species in Cultured Vascular Endothelial Cells after Exposure to TGF-β1: Induction of Cystathionine γ-Lyase and Cystathionine β-Synthase Expression Mediated by the ALK5-Smad2/3/4 and ALK5-Smad2/3-ATF4 Pathways

Transforming growth factor-β₁ (TGF-β₁) occurs at high levels at damage sites of vascular endothelial cell layers and regulates the functions of vascular endothelial cells. Reactive sulfur species (RSS), such as cysteine persulfide, glutathione persulfide, and hydrogen persulfide, are cytoprotective factors against electrophiles such as reactive oxygen species and heavy metals. Previously, we reported that sodium trisulfide, a sulfane sulfur donor, promotes vascular endothelial cell proliferation. The objective of the present study was to clarify the regulation and significance of RSS synthesis in vascular endothelial cells after exposure to TGF-β₁. Bovine aortic endothelial cells in a culture system were treated with TGF-β₁ to assess the expression of intracellular RSS, the effect of RSS on cell proliferation in the presence of TGF-β₁, induction of RSS-producing enzymes by TGF-β₁, and intracellular signal pathways that mediate this induction. The results suggest that TGF-β₁ increased intracellular RSS levels to modulate its inhibitory effect on proliferation. The increased production of RSS, probably high-molecular-mass RSS, was due to the induction of cystathionine γ-lyase and cystathionine β-synthase, which are RSS-producing enzymes, and the induction was mediated by the ALK5-Smad2/3/4 and ALK5-Smad2/3-ATF4 pathways in vascular endothelial cells. TGF-β₁ regulates vascular endothelial cell functions such as proliferation and fibrinolytic activity; intracellular high-molecular-mass RSS, which are increased by TGF-β₁, may modulate the regulation activity in vascular endothelial cells.     

Carbonylative Addition of Arylboronic Acids to Terminal Alkynes: A New Catalytic Access to α,β‐Unsaturated Ketones

The carbonylative addition of arylboronic acids to terminal alkynes under mild conditions affords (E)‐α,β‐unsaturated ketones with good yields. The reaction was achieved with chloro(1,5‐cyclooctadiene)rhodium(I) dimer or chlorodicarbonylrhodium(I) dimer as catalytic precursor without additional phosphine as their use inhibits the reaction. Experiments using deuterated 1‐hexyne discarded the possibility of a rhodium‐vinylidene intermediate, thus a catalytic cycle involving a 1,2‐insertion of the terminal alkyne in a rhodium‐acyl bond is proposed. This new reaction represents the first example of the hydroacylation of terminal alkynes involving rhodium‐acyl reagents generated under CO pressure and promises a wide field of interest.     

Adsorption and binding of the transgenic plant proteins, human serum albumin, β-glucuronidase, and Cry3Bb1, on montmorillonite and kaolinite: Microbial utilization and enzymatic activity of free and clay-bound proteins

Human serum albumin (HSA), β-glucuronidase (GUS), and the Cry3Bb1 protein from Bacillus thuringiensis subsp. kumamotoensis are expressed by genetically-modified plants. Commercial samples of these proteins adsorbed and bound rapidly on the clay minerals, kaolinite (K) and montmorillonite (M). Adsorption increased as the concentration of protein increased and then reached a plateau. The greatest amount of adsorption and binding occurred with the Cry3Bb1 protein, of which there was no desorption: 6.7 ±0.21 μg adsorbed and bound μg^− 1 of M; 2.1 ± 0.39 μg adsorbed and bound μg^− 1 of K. With GUS, 2.2 ± 0.29 μg adsorbed and 1.7 ±0.21 μg bound μg^− 1 of M; 1.5 ± 0.28 μg adsorbed and 1.0 ± 0.03 μg bound μg^− 1 of K. HSA was adsorbed and bound the least: 1.2 ±0.04 μg adsorbed and 0.8 ± 0.05 μg bound μg^− 1 of M; 0.4 ± 0.05 μg adsorbed and 0.4 ± 0.03 μg bound μg^− 1 of K. However, X-ray diffraction analyses indicated that only HSA intercalated M, and none of the proteins intercalated K, a nonswelling clay. When bound, the proteins were not utilized for growth by mixed cultures of soil microorganisms, whereas the cultures readily utilized the free (i.e., not adsorbed or bound) proteins as sources of carbon and energy. The enzymatic activity of GUS was significantly enhanced when bound on the clay minerals. These results indicated that recombinant proteins expressed by transgenic plants could persist and function in soil after release in root exudates and from decaying plant residues as the result of the protection provided against biodegradation by binding on clay minerals.     

La(1−x)SrxCo1−yFeyO3 perovskites prepared by sol–gel method: Characterization and relationships with catalytic properties for total oxidation of toluene

La_(1−x)Sr_xCo_(1−y)Fe_yO₃ samples have been prepared by sol–gel method using EDTA and citric acid as complexing agents. For the first time, Raman mappings were achieved on this type of samples especially to look for traces of Co₃O₄ that can be present as additional phase and not detect by XRD. The prepared samples were pure perovskites with good structural homogeneity. All these perovskites were very active for total oxidation of toluene above 200 °C. The ageing procedure used indicated good thermal stability of the samples. A strong improvement of catalytic properties was obtained substituting 30% of La³⁺ by Sr²⁺ cations and a slight additional improvement was observed substituting 20% of cobalt by iron. Hence, the optimized composition was La_0.7Sr_0.3Co_0.8Fe_0.2O₃. The samples were also characterized by BET measurements, SEM and XRD techniques. Iron oxidation states were determined by Mössbauer spectroscopy. Cobalt oxidation states and the amount of O⁻ electrophilic species were analyzed from XPS achieved after treatment without re-exposition to ambient air. Textural characterization revealed a strong increase in the specific surface area and a complete change of the shape of primary particles substituting La³⁺ by Sr²⁺. The strong lowering of the temperature at conversion 20% for the La_0.7Sr_0.3Co_(1−y)Fe_yO₃ samples can be explained by these changes. X photoelectron spectra obtained with our procedure evidenced very high amount of O⁻ electrophilic species for the La_0.7Sr_0.3Co_(1−y)Fe_yO₃ samples. These species able to activate hydrocarbons could be the active sites. The partial substitution of cobalt by iron has only a limited effect on the textural properties and the amount of O⁻ species. However, Raman spectroscopy revealed a strong dynamic structural distortion by Jahn–Teller effect and Mössbauer spectroscopy evidenced the presence of Fe⁴⁺ cations in the iron containing samples. These structural modifications could improve the reactivity of the active sites explaining the better specific activity rate of the La_0.7Sr_0.3Co_0.8Fe_0.2O₃ sample. Finally, an additional improvement of catalytic properties was obtained by the addition of 5% of cobalt cations in the solution of preparation. As evidenced by Raman mappings and TEM images, this method of preparation allowed to well-dispersed small Co₃O₄ particles that are very efficient for total oxidation of toluene with good thermal stability contrary to bulk Co₃O₄.     

Selective oxidation of propane and ethane on diluted Mo–V–Nb–Te mixed-oxide catalysts

Te-free and Te-containing Mo–V–Nb mixed oxide catalysts were diluted with several metal oxides (SiO₂, γ-Al₂O₃, α-Al₂O₃, Nb₂O₅, or ZrO₂), characterized, and tested in the oxidation of ethane and propane. Bulk and diluted Mo–V–Nb–Te catalysts exhibited high selectivity to ethylene (up to 96%) at ethane conversions <10%, whereas the corresponding Te-free catalysts exhibited lower selectivity to ethylene. The selectivity to ethylene decreased with the ethane conversion, with this effect depending strongly on the diluter and the catalyst composition. For propane oxidation, the presence of diluter exerted a negative effect on catalytic performance (decreasing the formation of acrylic acid), and α-Al₂O₃ can be considered only a relatively efficient diluter. The higher or lower interaction between diluter and active-phase precursors, promoting or hindering an unfavorable formation of the active and selective crystalline phase [i.e., Te₂M₂₀O₅₇ (M = Mo, V, and Nb)], determines the catalytic performance of these materials.     

Decreasing miscibility with greater heterogeneity in ternary polymer blend: poly(cyclohexyl methacrylate), poly(α‐methyl styrene) and poly(4‐methyl styrene)

A ternary blend system comprising poly(cyclohexyl methacrylate) (PCHMA), poly(α‐methyl styrene) (PαMS) and poly(4‐methyl styrene) (P4MS) was investigated by thermal analysis, optical and scanning electron microscopy. Ternary phase behaviour was compared with the behaviour for the three constituent binary pairs. This study showed that the ternary blends of PCHMA/PαMS/P4MS in most compositions were miscible, with an apparent glass transition temperature (T_g) and distinct cloud‐point transitions, which were located at lower temperatures than their binary counterparts. However, in a closed‐loop range of compositions roughly near the centre of the triangular phase diagram, some ternary blends displayed phase separation with heterogeneity domains of about 1 µm. Therefore, it is properly concluded that ternary PCHMA/PαMS/P4M is partially miscible with a small closed‐loop immisciblity range, even though all the constituent binary pairs are fully miscible. Thermodynamic backgrounds leading to decreased miscibility and greater heterogeneity in a ternary polymer system in comparison with the binary counterparts are discussed. © 2003 Society of Chemical Industry     

Surface alteration of (VO)2P2O7 by α-Sb2O4 as a route to control the n-butane selective oxidation

The catalytic properties of (VO)₂P₂O₇/α-Sb₂O₄ mixed oxides system for n-butane mild oxidation have been investigated on two mechanical mixtures (M1 and M2) of the same well crystallized (VO)₂P₂O₇ (reference vanadyl pyrophosphate) with two different morphologies of α-Sb₂O₄.The M1 mixture of (VO)₂P₂O₇ with α-Sb₂O₄ (1), prepared by oxidation of Sb₂O₃, leads to the oxidative dehydrogenation (ODH) of n-butane, whereas the M2 mixture of (VO)₂P₂O₇ with a commercial α-Sb₂O₄ (2) (Aldrich) with a different morphology improves the maleic anhydride selectivity as compared to the reference (VO)₂P₂O₇ catalyst (synergetic effect). After reaction, no ternary VPSbO phase is detected by XRD and DTA and it was controlled that the two α-Sb₂O₄ oxides are catalytically inactive.The (VO)₂P₂O₇ reference catalyst which produced only maleic anhydride as mild oxidation product shows by XPS a slightly oxidized surface (14% V⁵⁺–86% V⁴⁺).Contamination of the (VO)₂P₂O₇ phase by migration of Sb species occurs after catalytic reaction in the case of the M1 mixture as shown by XPS, LEIS and TEM–EDX analysis. XPS showed that (VO)₂P₂O₇ is partially superficially reduced (86% V⁴⁺–14% V³⁺). This feature is consistent with the decrease of acidity as observed by pyridine adsorption–desorption.In opposition with the M1 mixture, no contamination of the (VO)₂P₂O₇ phase is observed after catalytic reaction in the case of the M2 mixture. The XPS study shows, in this case, that (VO)₂P₂O₇ is partially oxidized (30% V⁵⁺–70% V⁴⁺) at a higher level than for the reference (VO)₂P₂O₇ catalyst. This situation is associated with the increase of selectivity observed for maleic anhydride (synergetic effect).The difference in the catalytic results for the two M1 and M2 mixtures, as compared to the (VO)₂P₂O₇ reference catalyst, can be explained by the alteration of the surface composition of (VO)₂P₂O₇ and the distribution of vanadium oxidation state due to different interaction between Sb₂O₄and (VO)₂P₂O₇, depending on the orientation of the α-Sb₂O₄ crystals.     

From single crystals to supported nanoparticles in experimental and theoretical studies of H2 oxidation over platinum metals (Pt, Pd): Intermediates, surface waves and spillover

The present paper reviews our investigations concerning the mechanism of H₂ + O₂ reaction on the metal surfaces (Pt, Pd) at different structures: single crystals (Pt(1 1 1), Pt(1 0 0), Pd(1 1 0)); microcrystals (Pt tips); and nanoparticles (Pd–Ti³⁺/TiO₂). Field electron microscopy (FEM), field ion microscopy (FIM), high-resolution electron energy loss spectroscopy (HREELS), XPS, UPS, work function (WF), TDS and temperature-programmed reaction (TPR) methods have been applied to study the kinetics of H₂ oxidation on a nanolevel. The adsorption of both O₂ and H₂ and several dissociative products (H_ads, O_ads, OH_ads) was studied by HREELS. Using the DFT technique the equilibrium states and stretching vibrations of H, O, OH, H₂O, adsorbed on the Pt(1 1 1) surface, have been calculated depending on the surrounding of the metal atoms. Sharp tips of Pt, several hundreds angstroms in radius, were used to perform in situ investigations of the dynamic surface processes. The FEM and FIM studies on the Pt-tip surface demonstrate that the self-oscillations and waves propagations are connected with periodic changes in the surface structure of nanoplane (1 0 0)-(hex) ↔ (1 × 1), varying the catalytic property of metal. The role of defects (Ti³⁺-□_O) in the adsorption centers formation, their stabilization by the palladium nanoparticles, and then the defects participation in H₂ + O₂ steady-state reaction over Pd–Ti³⁺/TiO₂ surface have been studied by XPS, UPS and photodesorption techniques (PhDS). This reaction seems to involve the “protonate” hydrogen atoms (H⁺/TiO_x) as a result of spillover effect: diffusion of H_ads atoms from Pd particles on a TiO_x surface. The comprehensive study of H₂, O₂ adsorption and H₂ + O₂ reaction in a row: single crystals → tips → nanoparticles has shown the same nature of active centers over these metal surfaces.     

Copper‐Catalyzed Oxidative α‐Alkylation of α‐Amino Carbonyl Compounds with Ethers via Dual C(sp3)‐H Oxidative Cross‐ Coupling

A novel copper‐catalyzed oxidative alkylation of α‐amino carbonyl compounds with ethers has been established for the selective synthesis of α‐etherized α‐amino carbonyl compounds. This oxidative alkylation is achieved by dual C(sp³) H bond oxidative cross‐coupling, and its scope is expanded to α‐amino ketones, α‐amino esters and α‐amino amides.

     

Dynamic Changes in Reactive Oxygen Species in the Shoot Apex Contribute to Stem Cell Death in Arabidopsis thaliana

In monocarpic plants, stem cells are fated to die. However, the potential mechanism of stem cell death has remained elusive. Here, we reveal that the levels of two forms of reactive oxygen species (ROS), superoxide anion free radical (O2·−) and hydrogen peroxide (H₂O₂), show dynamic changes in the shoot apex during the plant life cycle of Arabidopsis thaliana. We found that the level of O2·− decreased and disappeared at four weeks after bolting (WAB), while H₂O₂ appeared at 3 WAB and showed a burst at 5 WAB. The timing of dynamic changes in O2·− and H₂O₂ was delayed for approximately three weeks in clv3-2, which has a longer lifespan. Moreover, exogenous application of H₂O₂ inhibited the expression of the stem cell determinant WUSCHEL (WUS) and promoted the expression of the developmentally programmed cell death (dPCD) marker gene ORESARA 1 (ORE1). These results indicate that H₂O₂ triggers an important signal inducing dPCD in stem cells. Given that O2·− plays roles in maintaining WUS expression and stem cell activity, we speculate that the dynamic shift from O2·− to H₂O₂ in the shoot apex results in stem cell death. Our findings provide novel insights for understanding ROS-mediated regulation during plant stem cell death.     

A novel route to α,ω-telechelic poly(-caprolactone) diols, precursors of biodegradable polyurethanes, using catalysis by decamolybdate anion

A new convenient route for the synthesis of poly(-caprolactone) (PCL) with α,ω-telechelic diols' end-groups is presented. Synthesis of α,ω-telechelic PCL diols (HOPCLOH) was achieved by ring-opening polymerization (ROP) of -caprolactone (CL) catalyzed with ammonium decamolybdate (NH₄)₈[Mo₁₀O₃₄] and using diethylene glycol (DEG) as initiator. Obtained HOPCLOH was characterized by ¹H and ¹³C NMR, FT-IR, GPC and MALDI-TOF. Comparative studies demonstrate that ammonium decamolybdate (NH₄)₈[Mo₁₀O₃₄] is better catalyst than Sn-octanoate (SnOct₂) toward CL polymerization in presence of DEG, under the conditions tested. A biodegradable poly(ester-urethane-urea) derivative was efficiently prepared from synthesized HOPCLOH. Obtained polymer shows minor differences with respect to the properties recorded for a poly(ester-urethane-urea) obtained from commercial HOPCLOH.     

Formation and behavior of composite CO2 hydrate particles in a high-pressure water tunnel facility

Sinking CO₂ composite particles consisting of seawater, liquid CO₂, and CO₂ hydrate were produced by a coaxial flow injector fed with liquid CO₂ and artificial seawater. The particles were injected into a high-pressure water tunnel facility to permit determination of their settling velocities and dissolution rates. Injections were performed at fixed pressures approximately equivalent to 1200-m, 1500-m, and 1800-m depths and at temperatures varying from approximately 2 to 5 °C. Immediately after injection, the cylindrical particles were observed to break away from the injector tip and often aggregated into sinking clusters. The seawater flow in the tunnel was then adjusted in a countercurrent flow mode to suspend the particles in an observation window so that images of the particles could be recorded for later analysis. The flow would often break or cause rearrangement of some of the clusters. Selected individual particles and some clusters were studied until they became too hydrodynamically unstable to follow. In general, the flow required to suspend clusters or individual particles decreased with time as the particles dissolved. For example, one particle was produced and observed for over 6 min at an average pressure of 15.022 MPa and an average temperature of 5.1 °C. Its sinking rate, determined from the flow required for stabilization, changed from 37.2 to 3.3 mm/s over this time. Particle sinking rates were compared to correlations from the literature for uniform cylindrical objects. Reasonable agreement was observed for short times; however, the observed decrease in sinking velocity with time was greater than that predicted by the correlations for longer times. Particle dissolution rates, based on changes in diameter, were also determined and varied from 5 to . A pseudo-homogeneous mass transfer model was used to predict single-particle dissolution rates. Good agreement was achieved between experimental dissolution data and the modeling results.     

Polymer membranes for high temperature proton exchange membrane fuel cell: Recent advances and challenges

Proton-exchange membrane fuel cells (PEMFCs) are considered to be a promising technology for efficient power generation in the 21st century. Currently, high temperature proton exchange membrane fuel cells (HT-PEMFC) offer several advantages, such as high proton conductivity, low permeability to fuel, low electro-osmotic drag coefficient, good chemical/thermal stability, good mechanical properties and low cost. Owing to the aforementioned features, high temperature proton exchange membrane fuel cells have been utilized more widely compared to low temperature proton exchange membrane fuel cells, which contain certain limitations, such as carbon monoxide poisoning, heat management, water leaching, etc. This review examines the inspiration for HT-PEMFC development, the technological constraints, and recent advances. Various classes of polymers, such as sulfonated hydrocarbon polymers, acid-base polymers and blend polymers, have been analyzed to fulfill the key requirements of high temperature operation of proton exchange membrane fuel cells (PEMFC). The effect of inorganic additives on the performance of HT-PEMFC has been scrutinized. A detailed discussion of the synthesis of polymer, membrane fabrication and physicochemical characterizations is provided. The proton conductivity and cell performance of the polymeric membranes can be improved by high temperature treatment. The mechanical and water retention properties have shown significant improvement., However, there is scope for further research from the perspective of achieving improvements in certain areas, such as optimizing the thermal and chemical stability of the polymer, acid management, and the integral interface between the electrode and membrane.     

Silicate-based polymer-nanocomposite membranes for polymer electrolyte membrane fuel cells

Proton-exchange membrane fuel cells have emerged as a promising emission free technology to fulfill the existing power requirements of the 21st century. Nafion^® is the most widely accepted and commercialized membrane to date and possesses excellent electrochemical properties below 80 °C, under highly humidified conditions. However, a decrease in the proton conductivity of Nafion^® above 80 °C and lower humidity along with high membrane cost has prompted the development of new membranes and techniques. Addition of inorganic fillers, especially silicate-based nanomaterials, to the polymer membrane was utilized to partially overcome the aforementioned limitations. This is because of the lower cost, easy availability, high hydrophilicity and higher thermal stability of the inorganic silicates. Addition of silicates to the polymer membrane has also improved the mechanical, thermal and barrier properties, along with water uptake of the composite membranes, resulting in superior performance at higher temperature compared to that of the virgin membrane. However, the degrees of dispersion and interaction between the organic polymer and inorganic silicates play vital roles in improving the key properties of the membranes. Hence, different techniques and solvent media were used to improve the degrees of nanofiller dispersion and the physico-chemical properties of the membranes. This review focuses mainly on the techniques of silicate-based nanocomposite fabrication and the resulting impact on the membrane properties.