AM/AMPS/SSS三元反相乳液聚合体系稳定性研究

以丙烯酰胺(AM)为主单体、2-甲基-2-丙烯酰胺基丙磺酸(AMPS)、对苯乙烯磺酸钠(SSS)为抗温抗盐单体,以白油为连续相,Span 80/Tween 80为复合乳化剂,制得了AM/AMPS/SSS三元反相乳液聚合体系,考察了HLB值、乳化剂浓度、油水比、pH值、搅拌时间、搅拌速度对乳液稳定性的影响。结果表明,乳化剂含量为6%～7%(体系总量),HLB值为5.89,体系pH=8,油水体积比为1.8∶1,搅拌时间30～40 min,搅拌速度为500 r/min时得到稳定的反相乳液体系,适合进行三元反相乳液聚合。     

丙烯酰胺反相细乳液聚合

采用反相细乳液法,以白油为连续相,失水山梨醇单油酸酯/聚氧乙烯失水山梨醇单油酸酯为乳化剂,一种聚合物型乳化剂(聚异丁烯琥珀酸酯与山梨醇油酸酯的混合物)作为助稳定剂,通过正交实验确立了基本乳液体系,考察了微乳化工艺中转速变化、乳化剂体系组成、浓度及单体含量对聚合产物稳定性的影响,并研究了不同单体浓度和聚合时间等聚合工艺对微球粒径及分布的影响。结果表明,复合乳化剂含量为3.0%,转速为10 000 r/min下乳化20 min,在单体浓度55%,亲水疏水平衡值(HLB值)为5.5,采用氧化还原引发体系,聚合时间为6 h时,可以得到固含量35%以上、粒径数百纳米的长期稳定的亚微米级聚丙烯酰胺微球乳液。     

撞击流-旋转填料床制备丙烯酰胺反相乳液及其稳定性研究

以撞击流-旋转填料床为乳化设备,煤油为有机介质,山梨醇酐油酸酯(Span 80)和烷基酚聚氧乙烯醚(OP-10)为复配乳化剂制备了丙烯酰胺反相乳液,研究了超重力因子、撞击速度、油水体积比、乳化剂质量分数、复配乳化剂HLB值以及丙烯酰胺单体质量分数对乳液稳定性的影响,并与搅拌式乳化装置进行了对比研究。结果表明:在超重力因子为65.32,撞击速度为12.58 m/s,V(油相)∶V(水相)=1∶1,乳化剂质量占乳液总质量的5%,复配乳化剂HLB值为6.0,丙烯酰胺单体质量占单体水溶液总质量的15%的条件下,所制备乳液平均粒径为664 nm,稳定性系数达0.973;对比研究发现,采用撞击流-旋转填料床制备的乳液稳定性好,粒径小,分散均匀,乳化时间短,为连续化制乳过程。     

甲醇柴油乳液稳定性研究

在20℃下,研究了复配乳化剂及助乳化剂的含量、HLB值、甲醇含量、乳化时间及转速等对甲醇柴油乳液稳定性的影响规律。研究结果表明,随着复配乳化剂及助乳化剂的含量、HLB值和转速的增大,乳液的稳定性呈现先升高后降低的趋势。随着乳化时间的延长,稳定性先升高后趋于基本稳定。随着甲醇含量的增大,乳液的稳定性逐渐降低。实验得到的适宜操作参数:乳化时间为2 min、转速为5×2 800 r·min-1、HLB值为4.5、乳化剂及助乳化剂质量分数均为3%、甲醇质量分数为15%。测得Sauter平均直径D=13μm。     

相反转法水性环氧树脂的制备

以Span-80和SDS为复合乳化剂,将环氧树脂E-51用相反转法乳化成水包油的稳定乳液。研究了复合乳化剂的亲水亲油平衡值(HLB)、乳化剂的浓度以及乳化温度对环氧树脂E-51相反转点时含水量R_f值、乳液的粒径及粒径分布和乳液离心稳定性的影响,并通过透射电镜(TEM)对乳液粒子的大小、形貌进行表征。结果表明:当复合乳化剂的HLB值为16.2,即Span-80与SDS的质量比为2:1时,乳化剂的质量分数为9%,乳化温度为50℃时,得到的乳液稳定性最好,乳液粒子大小均匀、粒径分布较窄。     

白油W/O/W型多重乳状液的稳定性研究

以多重乳状液相对体积为衡量标准,用显微镜直接观察,探讨了乳化剂的HLB值、质量分数、亲油亲水乳化剂体积比及油水的相比等对白油W/O/W型多重乳状液体系稳定性的影响。结果表明单一乳化剂体系中适宜的制备条件:乳液中乳化剂质量分数为12.2%,V(Span80)/V(Tween80)=7.5;适合多重乳液稳定的油水相比为:第一相体积比为2.5,第二相体积比为0.2。复合乳化剂体系中适宜的制备条件:第一相乳化剂的HLB值为6.5,V(复合乳化剂)/V(Tween80)=27.5,乳液中乳化剂质量分数为9.5%。     

含聚合型乳化剂反相乳液体系的稳定性研究

以煤油为油相,丙烯酸钠水溶液为水相,自制的非离子聚合型乳化剂-Span80丙烯酸酯(Span80AA)、Span80和Twen80组成复合乳化剂,制备反相乳液。计算出Span80AA的HLB值,考察了乳化剂浓度、水相体积分数Φ及单体浓度对乳液类型及稳定性的影响。结果表明:HLB(Span80AA)=2.709;Span80AA、Span80和Twen80的最佳质量比为0.8∶0.3∶0.1。形成稳定的反相乳液理想条件是:复合乳化剂质量分数为6%~8%;Φ<57%;单体浓度为2.0~3.5 mol/L。     

石蜡乳液稳定性研究

以58#全精炼石蜡为原料,采用复配乳化剂(Tween-60和Span-60)分别溶解的方法制备石蜡乳液。利用均匀设计安排实验,建立石蜡乳化的回归方程。通过规划求解确定复配乳化剂的HLB值(亲水亲油平衡值)为9.93,水蜡比为3(w/w),乳化时间为20 min。以表面张力和Zeta电位为考察指标,通过单因素实验优化石蜡乳化工艺条件。结果表明,当HLB值为9.93,水蜡比为3.4,乳化剂含量为9%(w/w),乳化温度为80℃,乳化时间为30 min时,石蜡乳液的稳定性最好;在石蜡乳液中添加2%(w/w)异戊醇后,乳液的粒径变得更加均匀,乳液的稳定性增强。     

聚甘油单硬脂酸酯乳化二甲基硅油及乳液表征

用聚甘油单硬脂酸酯复配乳化1 Pa.s的二甲基硅油,考察复配乳化剂的亲水亲油平衡值(HLB)对乳液体积平均粒径、乳液黏度、乳液离心稳定性的影响以及乳液的耐高温稳定性。结果表明:复配乳化剂HLB值对乳液体积平均粒径、黏度、离心稳定性的影响显著,选择高聚合度的亲水型乳化剂和高聚合度的亲油型乳化剂进行复配乳化,有利于形成稳定的硅油乳液。最佳乳化条件为乳化剂(二聚甘油单硬酯和八聚甘油单硬脂酸酯,HLB=10.5)、硅油和水的质量比为7∶23∶70。在最佳乳化条件下制得的乳液体积平均粒径为8.06μm,黏度为387 mPa.s,固相质量分数差为2.91%。乳液高温稳定性良好,在110℃保持5 h,乳液体积平均粒径增大至11.63μm,固相质量分数差增大至6.12%。     

DMDAAC-AM-MA反相微乳液聚合体系的制备与优化

以二甲基二烯丙基氯化铵(DMDAAC)、丙烯酰胺(AM)和顺丁烯二酸(MA)为乳化单体,正丁醇为助乳化剂,聚氧乙烯辛基苯酚醚-10(Triton X-10)、失水山梨醇油酸酯(Span 80)和聚氧乙烯山梨醇酐硬脂酸酯(Tween 60)为乳化剂,液体石蜡、异辛烷和环己烷为有机溶剂,进行体系增溶实验。采用电导法和染料法研究了单体总质量浓度、AM摩尔分数、阴阳离子单体配比、乳化剂质量分数、助乳化剂与复合乳化剂质量比等对微乳液体系最小乳化剂用量(Smin)和最大增溶水量的影响。结果表明,异辛烷与Span80/Tween60复合乳化剂组成的乳化体系增溶性较好;当单体总质量浓度为40%、n(AM)∶n(MA)∶n(DMDAAC)=6∶2∶2、亲水亲油平衡值(HLB值)为11.30、w(复合乳化剂)=33%和m(助乳化剂)∶m(复合乳化剂)=1∶7时,所形成的反相微乳液增溶水量大、乳化剂用量少且稳定性强。     

Insect antifeedant properties of anthranoids from the genusVismia

Vismiones and ferruginins, representatives of a new class of lypophilic anthranoids from the genusVismia were found to inhibit feeding in larvae of species ofSpodoptera, Heliothis, and inLocusta migratoria.     

Direct observation of freeze-thaw instability of latex coatings via high pressure freezing and cryogenic SEM

Despite its industrial importance, the subject of freeze-thaw (F/T) stability of latex coatings has not been studied extensively. There is also a lack of fundamental understanding about the process and the mechanisms through which a coating becomes destabilized. High pressure (2100 bar) freezing fixes the state of water-suspended particles of polymer binder and inorganic pigments without the growth of ice crystals during freezing that produce artifacts in direct imaging scanning electron microscopy (SEM) of fracture surfaces of frozen coatings. We show that by incorporating copolymerizable functional monomers, it is possible to achieve F/T stability in polymer latexes and in low-VOC paints, as judged by the microstructures revealed by the cryogenic SEM technique. Particle coalescence as well as pigment segregation in F/T unstable systems are visualized. In order to achieve F/T stability in paints, latex particles must not flocculate and should provide protection to inorganic pigment and extender particles. Because of the unique capabilities of the cryogenic SEM, we are able to separate the effects of freezing and thawing, and study the influence of the rate of freezing and thawing on F/T stability. Destabilization can be caused by either freezing or thawing. A slow freezing process is more detrimental to F/T stability than a fast freezing process; the latter actually preserves suspension stability during freezing. Presented at the 82nd Annual Meeting of the Federation of Societies for Coatings Technology, October 27–29, 2004 in Chicago, IL. Tied for first place in The John A. Gordon Best Paper Competition.     

Ethanol and (−)-α-Pinene: Attractant Kairomones for Bark and Ambrosia Beetles in the Southeastern US

In 2002–2004, we examined the flight responses of 49 species of native and exotic bark and ambrosia beetles (Coleoptera: Scolytidae and Platypodidae) to traps baited with ethanol and/or (−)-α-pinene in the southeastern US. Eight field trials were conducted in mature pine stands in Alabama, Florida, Georgia, North Carolina, and South Carolina. Funnel traps baited with ethanol lures (release rate, about 0.6 g/day at 25–28°C) were attractive to ten species of ambrosia beetles (Ambrosiodmus tachygraphus, Anisandrus sayi, Dryoxylon onoharaensum, Monarthrum mali, Xyleborinus saxesenii, Xyleborus affinis, Xyleborus ferrugineus, Xylosandrus compactus, Xylosandrus crassiusculus, and Xylosandrus germanus) and two species of bark beetles (Cryptocarenus heveae and Hypothenemus sp.). Traps baited with (−)-α-pinene lures (release rate, 2–6 g/day at 25–28°C) were attractive to five bark beetle species (Dendroctonus terebrans, Hylastes porculus, Hylastes salebrosus, Hylastes tenuis, and Ips grandicollis) and one platypodid ambrosia beetle species (Myoplatypus flavicornis). Ethanol enhanced responses of some species (Xyleborus pubescens, H. porculus, H. salebrosus, H. tenuis, and Pityophthorus cariniceps) to traps baited with (−)-α-pinene in some locations. (−)-α-Pinene interrupted the response of some ambrosia beetle species to traps baited with ethanol, but only the response of D. onoharaensum was interrupted consistently at most locations. Of 23 species of ambrosia beetles captured in our field trials, nine were exotic and accounted for 70–97% of total catches of ambrosia beetles. Our results provide support for the continued use of separate traps baited with ethanol alone and ethanol with (−)-α-pinene to detect and monitor common bark and ambrosia beetles from the southeastern region of the US.     

Methyl 2,4,6-decatrienoates Attract Stink Bugs and Tachinid Parasitoids

Halyomorpha halys (Stål) (Pentatomidae), called the brown marmorated stink bug (BMSB), is a newly invasive species in the eastern USA that is rapidly spreading from the original point of establishment in Allentown, PA. In its native range, the BMSB is reportedly attracted to methyl (E,E,Z)-2,4,6-decatrienoate, the male-produced pheromone of another pentatomid common in eastern Asia, Plautia stali Scott. In North America, Thyanta spp. are the only pentatomids known to produce methyl 2,4,6-decatrienoate [the (E,Z,Z)-isomer] as part of their pheromones. Methyl 2,4,6-decatrienoates were field-tested in Maryland to monitor the spread of the BMSB and to explore the possibility that Thyanta spp. are an alternate host for parasitic tachinid flies that use stink bug pheromones as host-finding kairomones. Here we report the first captures of adult and nymph BMSBs in traps baited with methyl (E,E,Z)-2,4,6-decatrienoate in central Maryland and present data verifying that the tachinid, Euclytia flava (Townsend), exploits methyl (E,Z,Z)-2,4,6-decatrienoate as a kairomone. We also report the unexpected finding that various isomers of methyl 2,4,6-decatrienoate attract Acrosternum hilare (Say), although this bug apparently does not produce methyl decatrienoates. Other stink bugs and tachinids native to North America were also attracted to methyl 2,4,6-decatrienoates. These data indicate there are Heteroptera in North America in addition to Thyanta spp. that probably use methyl 2,4,6-decatrienoates as pheromones. The evidence that some pentatomids exploit the pheromones of other true bugs as kairomones to find food or to congregate as a passive defense against tachinid parasitism is discussed.     

2007～2008年世界塑料工业进展

收集了2007年7月～2008年6月世界塑料工业的相关资料,介绍了2007～2008年国外塑料工业的发展情况,提供了世界塑料产量、消费量及全球各类树脂的需求量及产能情况.按通用热塑性树脂(聚乙烯、聚丙烯、聚苯乙烯、聚氯乙烯、ABS树脂)、工程塑料(尼龙、聚碳酸酯、聚甲醛、热塑性聚酯、聚苯醚)、特种工程塑料(聚苯·硫醚、液晶聚合物、聚醚醚酮)、通用热固性树脂(酚醛、聚氨酯、不饱和聚酯树脂、环氧树脂)不同品种的顺序,对树脂的产量、消费量、供需状况及合成工艺、产品应用开发、树脂品种的延伸及应用的进一步扩展等技术作了详细介绍.     

2005～2006年国外塑料工业进展

收集了2005年7月～2006年6月国外塑料工业的相关资料,介绍了2005—2006年国外塑料工业的发展情况。提供了世界塑料产量、消费量及全球各类树脂生产量以及各国塑料制品的进出口情况。作为对比,介绍了中国塑料的生产情况。按通用热塑性树脂（聚乙烯、聚丙烯、聚苯乙烯、聚氯乙烯、ABS树脂）、工程塑料（聚酰胺、聚碳酸酯、聚甲醛、热塑性聚酯、聚苯醚）、通用热固性树脂（酚醛、聚氨酯、不饱和树脂、环氧树脂）、特种工程塑料（聚苯硫醚、液晶聚合物、聚醚醚酮）的品种顺序,对树脂的产量、消费量、供需状况及合成工艺、产品开发、树脂品种的延伸及应用的扩展作了详细的介绍。