Effect of sintering temperature on varistor properties and aging characteristics of ZnO–V2O5–MnO2 ceramics

The microstructure, electrical properties, dielectric characteristics, and DC accelerated aging behavior of the ZVM-based varistors were investigated for different sintering temperatures of 800–950 °C. The microstructure of the ZVM-based ceramics consisted of mainly ZnO grain and secondary phase Zn₃(VO₄)₂, which acts as liquid-phase sintering aid. The Zn₃(VO₄)₂ has a significant effect on the sintered density, in the light of an experimental fact, which the decreases of the Zn₃(VO₄)₂ distribution with increasing sintering temperature resulted in the low sintered density. The breakdown field exhibited the highest value (17,640 V/cm) at 800 °C in the sintering temperature and the lowest value (992 V/cm) at 900 °C in the sintering temperature. The nonlinear coefficient exhibited the highest value, reaching 38 at 800 °C and the lowest value, reaching 17 at 850 °C. The varistor sintered at 900 °C exhibited not only high nonlinearity with 27.2 in nonlinear coefficient, but also the highest stability, in which %ΔE_1 mA = −0.6%, %Δα = −26.1%, and %Δ tan δ = +21.8% for DC accelerated aging stress of 0.85 E_1 mA/85 °C/24 h.     

Dielectric properties and microstructures of CaSiO3 ceramics with B2O3 addition

The effects of B₂O₃ additives on the sintering behavior, microstructure and dielectric properties of CaSiO₃ ceramics have been investigated. The B₂O₃ addition resulted in the emergence of CaO–B₂O₃–SiO₂ glass phase, which was advantageous to lower the synthesis temperature of CaSiO₃ crystal phase, and could effectively lower the densification temperature of CaSiO₃ ceramic to as low as 1100 °C. The 6 wt% B₂O₃-doped CaSiO₃ ceramic sintered at 1100 °C possessed good dielectric properties: _r = 6.84 and tan δ = 6.9 × 10⁻⁴ (1 MHz).     

The influence of sintering aids for Nd(Mg0.5Ti0.5)O3 microwave dielectric ceramics properties

The influence of various sintering aids on the microwave dielectric properties and the structure of Nd(Mg_0.5Ti_0.5)O₃ ceramics were investigated systematically. B₂O₃, Bi₂O₃, and V₂O₅ were selected as liquid-phase sintering aids to lower the sintering temperature. The sintered Nd(Mg_0.5Ti_0.5)O₃ ceramics are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and microwave dielectric properties. The sintering temperature of Nd(Mg_0.5Ti_0.5)O₃ microwave dielectric ceramics is generally high, about 1500 °C. However, the sintering temperature was significantly lowered about 175 °C from 1500 °C to 1325 °C by incorporating in 10 mol% B₂O₃ and revealed the optimum microwave dielectric properties of dielectric constant (_r) value of 26.2, a quality factor (Q × f) value of 61,307 (at 9.63 GHz), and τ_f value of −45.5 ppm/°C. NdVO₄ secondary phase was observed at 10 mol% V₂O₅ addition in the sintering temperature range of 1300–1325 °C, which led the degradation in microwave dielectric properties. The microwave dielectric properties as well as grain sizes, grain morphology, and bulk density were greatly dependent on sintering temperature and various sintering aids. In this study, it is found that Nd(Mg_0.5Ti_0.5)O₃ incorporated with 10 mol% B₂O₃ with lower sintering temperature and excellent dielectric microwave properties may be suggested for application in microwave communication devices. The use of liquid-phase sintering, the liquid formed during firing normally remains as a grain boundary phase on cooling. This grain boundary phase can cause a deterioration of the microwave properties. Therefore, the selection of a suitable sintering aid is extremely important.     

Microstructure and dielectric properties of low temperature sintered ZnNb2O6 microwave ceramics

Low sintering temperature ZnNb₂O₆ microwave ceramics were prepared by doping with mixed oxides of V₂O₅–Bi₂O₃ and V₂O₅–Bi₂O₃–CuO. The effects of additives on the microstructure and dielectric properties of the ceramics were investigated. The results show that doping with V₂O₅–Bi₂O₃ can reduce the sintering temperature of ZnNb₂O₆ from 1150 °C to 1000 °C due to the formation of V₂O₅ and Bi₂O₃ based eutectic phases. The combined influence of V₂O₅ and Bi₂O₃ resulted in rod-like grains. Co-doping CuO with 1 wt.% V₂O₅–1 wt.% Bi₂O₃ further lowered the sintering temperature to 880 °C, because eutectic phases could be formed between the CuO, V₂O₅ and Bi₂O₃. A second phase of (Cu₂Zn)Nb₂O₈ also forms when the content of CuO is greater than 2.5 wt.%. A pure ZnNb₂O₆ phase can be obtained when the amount of CuO was 1.0–2.5 wt.%. The Q × f values of ZnNb₂O₆ ceramics doped with V₂O₅–Bi₂O₃–CuO were all higher than 25,000 GHz. The dielectric constants were 22.8–23.8 at microwave frequencies. In addition, theτ_f values decreased towards negative as the content of CuO increased. The ceramic with composition of ZnNb₂O₆ + 1 wt.%V₂O₅ + 1 wt.% Bi₂O₃ + 2.5 wt.% CuO sintered at 880 °C exhibited the optimum microwave dielectric properties, is 23.4, Q × f is 46,975 GHz, and τ_f is −44.89 ppm/°C, which makes it a promising material for low-temperature co-fired ceramics (LTCCs).     

Dielectric and piezoelectric properties of (Ba0.95Ca0.05)(Ti0.88Zr0.12)O3 ceramics sintered in a protective atmosphere

(Ba_0.95Ca_0.05)(Ti_0.88Zr_0.12)O₃ (BCTZ) ceramics have been produced in a protective atmosphere of industrial N₂ gas for potential piezoelectric applications. For comparison, the ceramics were also sintered at 1200–1400 °C in air. The results revealed that the reducing atmosphere of pO₂ = 5 × 10² Pa had no substantial effect on the phase structure or the microstructure of the BCTZ ceramics. The XRD patterns suggested a tetragonal to pseudocubic phase transition at sintering temperatures above 1300 °C in both atmospheres. The nitrogen-sintered BCTZ samples had higher dielectric constants _r but lower electromechanical coupling coefficients k_p than the air-sintered samples. The piezoelectric constant d₃₃ for the BCTZ ceramics was not significantly influenced by the reducing atmosphere of pO₂ = 5 × 10² Pa. The correlation of dielectric and piezoelectric properties of the BCTZ ceramics with the sintering temperature was explained based on a competing mechanism between phase structure and microstructure.     

A simple and effective process for fabrication of Gd0.1Ce0.9O1.95 solid electrolyte ceramics

Ce_0.9Gd_0.1O_1.95 ceramics were prepared using a simple and effective process in this study. Without any prior calcination, the mixture of raw materials was pressed and sintered directly. The reaction of the raw materials occurred during the heating up period by passing the calcination stage in the conventional solid-state reaction method. More than 99.5% of theoretical density was obtained for Ce_0.9Gd_0.1O_1.95 sintering at 1500–1600 °C. Fine grains (<1 μm) formed in pellets sintered at 1450 °C. The homogeneity of grains increased with the sintering temperature. The grains grew to >4.5 μm in pellets sintered at 1600 °C. The reactive-sintering process is proved to be a simple and effective method in preparing Ce_0.9Gd_0.1O_1.95 ceramics for solid electrolyte application.     

Synthesis of Zn3Nb2O8 ceramics using a simple and effective process

Synthesis of Zn₃Nb₂O₈ ceramics using a simple and effective reaction-sintering process was investigated. The mixture of ZnO and Nb₂O₅ was pressed and sintered directly without any prior calcination. Single-phase Zn₃Nb₂O₈ ceramics could be obtained. Density of these ceramics increased with soaking time and sintering temperature. A maximum density 5.72 g/cm³ (99.7% of the theoretical density) was found for pellets sintered at 1170 °C for 2 h. Pores were not found and grain sizes >20 μm were observed in pellets sintered at 1170 °C. Abnormal grain growth occurred and grains >50 μm could be seen in Zn₃Nb₂O₈ ceramics sintered at 1200 °C for 2 h and 1200 °C for 4 h. Reaction-sintering process is then a simple and effective method to produce Zn₃Nb₂O₈ ceramics for applications in microwave dielectric resonators.     

Effect of ceria on the structure and catalytic activity of V2O5/TiO2–ZrO2 for oxidehydrogenation of ethylbenzene to styrene utilizing CO2 as soft oxidant

The present study was undertaken to investigate the influence of ceria on the physicochemical and catalytic properties of V₂O₅/TiO₂–ZrO₂ for oxidative dehydrogenation of ethylbenzene to styrene utilizing CO₂ as a soft oxidant. Monolayer equivalents of ceria, vanadia and ceria–vanadia combination over TiO₂–ZrO₂ (TZ) support were impregnated by a coprecipitation and wet impregnation methods. Synthesized catalysts were characterized by using X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy, temperature programmed reduction, transmission electron microscopy and BET surface area methods. The XRD profiles of 550 °C calcined samples revealed amorphous nature of the materials. Upon increasing calcination temperature to 750 °C, in addition to ZrTiO₄ peaks, few other lines due to ZrV₂O₇ and CeVO₄ were observed. The XPS V 2p results revealed the existence of V⁴⁺ and V⁵⁺ species at 550 and 750 °C calcinations temperatures, respectively. TEM analysis suggested the presence of nanosized (<7 nm) particles with narrow range distribution. Raman measurements confirmed the formation ZrTiO₄ under high temperature treatments. TPR measurements suggested a facile reduction of CeO₂–V₂O₅/TZ sample. Among various samples evaluated, the CeO₂–V₂O₅/TZ sample exhibited highest conversion and nearly 100% product selectivity. In particular, the addition of ceria to V₂O₅/TZ suppressed the coke deposition and allowed a stable and high catalytic activity.     

TEM observation of liquid phase sintering in V2O5 modified Zr0.8Sn0.2TiO4 microwave ceramics

The phenomena of liquid phase sintering in the V₂O₅ modified (Zr_0.8, Sn_0.2)TiO₄ (ZST) microwave ceramics has been investigated by using transmission electron microscopy (TEM) and energy dispersive X-ray analysis (EDS). The amounts of second phase were too low to be detected by X-ray diffraction (XRD), but could be observed by TEM bright field image. However, the presence of grain boundary phases did not degrade the microwave properties of V₂O₅ modified ZST ceramics. The ?_r value of 37.2, Q × f value of 51,000 (at 7 GHz) and τ_f value of −2.1 ppm/°C were obtained for ZST ceramics with 1 wt% V₂O₅ addition sintered at 1300 °C.     

Transparent polycrystalline MgAl2O4 ceramic fabricated by spark plasma sintering: Microwave dielectric and optical properties

The optical properties and microwave dielectric properties of transparent polycrystalline MgAl₂O₄ ceramics sintered by spark plasma sintering (SPS) through homemade nanosized MgAl₂O₄ powders at temperatures between 1250 °C and 1375 °C are discussed. The results indicate that, with increasing sintering temperatures, grain growth and densification occurred up to 1275 °C, and above 1350 °C, rapid grain and pore growth occurred. The in-line light transmission increases with the densification and decreases with the grain/pore growth, which can be as high as 70% at the wavelength of 550 nm and 82% at the wavelength of 2000 nm, respectively. As the sintering temperature increases, Q×f and dielectric constant ε_r values increase to maximum and then decrease respectively, while τ_f value is almost independent of the sintering temperatures and remains between −77 and −71 ppm/°C. The optimal microwave dielectric properties (ε_r=8.38, Q×f=54,000 GHz and τ_f=−74 ppm/°C) are achieved for transparent MgAl₂O₄ ceramics produced by spark plasma sintering at 1325 °C for 20 min.     

Microwave dielectric properties of SnO2-doped CaSiO3 ceramics

SnO₂-doped CaSiO₃ ceramics were successfully synthesized by a solid-state method. Effects of different SnO₂ additions on the sintering behavior, microstructure and dielectric properties of Ca(Sn_1−xSi_x)O₃ (x=0.5–1.0) ceramics have been investigated. SnO₂ improved the densification process and expanded the sintering temperature range effectively. Moreover, Sn⁴⁺ substituting for Si⁴⁺ sites leads to the emergence of Ca₃SnSi₂O₉ phase, which has a positive effect on the dielectric properties of CaO–SiO₂–SnO₂ materials, especially the Qf value. The Ca(Sn_0.1Si_0.9)O₃ ceramics sintered at 1375 °C possessed good microwave dielectric properties: ε_r =7.92, Qf =58,000 GHz and τ_f=−42 ppm/°C. The Ca(Sn_0.4Si_0.6)O₃ ceramics sintered at 1450 °C also exhibited good microwave dielectric properties of ε_r=9.27, Qf=63,000 GHz, and τ_f=−52 ppm/°C. Thus, they are promising candidate materials for millimeter-wave devices.     

ZnBO-doped (Ba, Sr)TiO3 ceramics for the low-temperature sintering process

ZnBO-doped (Ba, Sr)TiO₃ ceramics were investigated for low-temperature co-fired ceramics (LTCCs) applications. Until now, B₂O₃ and Li₂CO₃ dopants have been commonly employed as the low-temperature sintering aids. In this paper, we suggest ZnBO as an alternative dopant to the B₂O₃ and Li₂CO₃. To reduce the sintering temperature of (Ba, Sr)TiO₃, we have added 1–5 wt.% of ZnBO to (Ba, Sr)TiO₃. ZnBO-doped (Ba, Sr)TiO₃ ceramics were respectively sintered from 750 to 1350 °C by 50 °C to confirm the sintering temperature with different dopant contents. By adding 5 wt.% of ZnBO to the (Ba, Sr)TiO₃ ceramics, the sintering temperature of (Ba, Sr)TiO₃ ceramics can be reduced to 1100 °C. From the XRD analysis, ZnBO-doped (Ba, Sr)TiO₃ has no pyro phase. By adding ZnBO dopants to (Ba, Sr)TiO₃ ceramics, both of relative dielectric permittivity and loss tangent were decreased. From the frequency dispersion of dielectric properties, the relative dielectric permittivity and loss tangent of 5 wt.% ZnBO-doped (Ba, Sr)TiO₃ were 1180 and 3.3 × 10⁻³, while those of BST were 1585 and 4.8 × 10⁻³, respectively.     

Densification, microstructural evolution and microwave dielectric properties of fluxed sintered 12R-Ba(Ti0.5Mn0.5)O3 ceramics

Doped hexagonal BaTiO₃ (h-BaTiO₃) ceramics have recently been identified as potential candidates for use in microwave dielectric resonators. However, similar to other common microwave ceramics, doped h-BaTiO₃ ceramics require a sintering temperature higher than 1400 °C. In this study, the effects of Bi₂O₃ and Li₂CO₃ on the densification, microstructural evolution and microwave properties of hexagonal 12R-Ba(Ti_0.5Mn_0.5)O₃ ceramics were examined. Results indicate that Bi₂O₃ and Li₂CO₃ are able to effectively reduce the sintering temperature of 12R-Ba(Ti₀₅Mn_0.5)O₃ ceramics through liquid phase sintering while retaining the hexagonal structure and the microwave dielectric properties. The best results were obtained for the 12R-Ba(Ti_0.5Mn_0.5)O₃ with the additions of 5 wt% Bi₂O₃ sintered at 1200 °C (?_r: 36.0, Qf_r: 6779 GHz, and τ_f: 25.3 ppm/°C), and 5 wt% Li₂CO₃ sintered at 1200 °C (?_r: 28.1, Qf_r: 5304 GHz, and τ_f: 35.3 ppm/°C).     

Nanocomposite Fe2O3–SiO2 inclusion pigments from post-functionalized mesoporous silicas

High-surface mesoporous silicas with different pore sizes were employed for the first time as silicon precursors in the synthesis of reddish Fe₂O₃–SiO₂ inclusion pigments. Interestingly, the size of included Fe₂O₃ nanoparticles was partially controlled through confinement effects into silica mesopores. Notably, impregnated samples showed a more homogeneous and efficient encapsulation of smaller and monodisperse hematite nanoparticles (sizes around 10–35 nm). Moreover, they resulted in an improved reddish color at 1000 °C within a ceramic glaze. The best red shade (a* ≈ 18) was associated to nanocomposite with smaller hematite nanoparticles (around 5 nm). These promising results suggest the possibility to improve the reddish coloration and thermostability of Fe₂O₃–SiO₂ ceramic pigments through and adequate control of confinement effects into sintered mesoporous silicas.     

Enhancement of oxygen storage capacity by reductive treatment of Al2O3 and CeO2–ZrO2 solid solution nanocomposite

Oxygen storage capacity (OSC) of CeO₂–ZrO₂ solid solution, Ce_xZr_(1−x)O₄, is one of the most contributing factors to control the performance of an automotive catalyst. To improve the OSC, heat treatments were employed on a nanoscaled composite of Al₂O₃ and CeZrO₄ (ACZ). Reductive treatments from 700 to 1000 °C significantly improved the complete oxygen storage capacity (OSC-c) of ACZ. In particular, the OSC-c measured at 300 °C reached the theoretical maximum with a sufficient specific surface area (SSA) (35 m²/g) after reductive treatment at 1000 °C. The introduced Al₂O₃ facilitated the regular rearrangement of Ce and Zr ions in CeZrO₄ as well as helped in maintaining the sufficient SSA. Reductive treatments also enhanced the oxygen release rate (OSC-r); however, the OSC-r variation against the evaluation temperature and the reduction temperature differed from that of OSC-c. OSC-r measured below 200 °C reached its maximum against the reduction temperature at 800 °C, while those evaluated at 300 °C increased with the reduction temperature in the same manner as OSC-c.     

Thermal shock resistance of in situ formed Si2N2O–Si3N4 composites by gelcasting

Thermal shock resistance of Si₂N₂O–Si₃N₄ composites was evaluated by water quenching and subsequent three-point bending tests of strength diminution. Si₂N₂O–Si₃N₄ composites which was prepared with in situ liquid pressureless sintering process using Yb₂O₃ and Al₂O₃ powders as sintering additives by gelcasting showed no macroscopic cracks and the critical temperature difference (ΔT_c) could be up to 1400 °C. A mass of pores existed in the sintered body and the irregular shaped fibers extended from the pores increased the thermal shock property.     

Effects of Al2O3 addition on the sintering behavior and microwave dielectric properties of CaSiO3 ceramics

The effects of Al₂O₃ addition on the densification, structure and microwave dielectric properties of CaSiO₃ ceramics have been investigated. The Al₂O₃ addition results in the presence of two distinct phases, e.g. Ca₂Al₂SiO₇ and CaAl₂Si₂O₈, which can restrict the growth of CaSiO₃ grains by surrounding their boundaries and also improve the bulk density of CaSiO₃-Al₂O₃ ceramics. However, excessive addition (≥2 wt%) of Al₂O₃ undermines the microwave dielectric properties of the title ceramics since the derived phases of Ca₂Al₂SiO₇ and CaAl₂Si₂O₈ have poor quality factor. The optimum amount of Al₂O₃ addition is found to be 1 wt%, and the derived CaSiO₃-Al₂O₃ ceramic sintered at 1250 °C presents improved microwave dielectric properties of ?_r = 6.66 and Q × f = 24,626 GHz, which is much better than those of pure CaSiO₃ ceramic sintered at 1340 °C (Q × f = 13,109 GHz).     

Crystalline morphology and photoluminescent properties of YInGe2O7:Eu phosphors prepared from microwave and conventional sintering

This paper describes an investigation of the crystalline morphology and photoluminescent properties of YInGe₂O₇:Eu³⁺ powders using microwave assisted sintering. For comparison, the properties of YInGe₂O₇:Eu³⁺ powders sintered at 1200 °C in conventional furnace for 10 h were also investigated. X-ray powder diffraction analysis confirmed the formation of monoclinic YInGe₂O₇ without second phase or phases of starting materials as YInGe₂O₇:50 mol% Eu powders sintered at 1200 °C in microwave furnace for 1 h. Scanning electron microscopy showed smaller particle size and more uniform grain size distributions are obtained by microwave assisted sintering. In the PL studies, both microwave sintered and conventionally sintered powders emitted a maximum luminescence centered at 620 nm under excitation of 393 nm with similar luminescent intensity. The results show that microwave processing has the potential to reduce the time and required energy input for the production of YInGe₂O₇:Eu³⁺ phosphors without sacrificing the photoluminescence.     

Effect of Y2O3 additive on conventional and microwave sintering of mullite

Mullite has become a strong candidate material for advanced structural and functional ceramics. Much interest has recently focused on sintering aids for mullite. The aim of this study was to evaluate the effect of Y₂O₃ as a sintering aid in the conventional and microwave sintering of mullite. To accomplish this study, a highly pure industrial mullite was used. Mullite with and without Y₂O₃ was pressed under a cold isostatic pressure of 200 MPa. Samples were sintered conventionally at 1400, 1450, 1500, 1550 and 1600 °C for 2 h and microwave-sintered for up to 40 min using a large range of power. The microstructure and physical properties of the microwave-sintered samples were compared to those of the conventionally sintered samples. The results showed that Y₂O₃ improved the densification of mullite bodies in the conventional and microwave sintering processes, but high densifications were achieved in just a few minutes when Y₂O₃ was used with microwave processing.     

Preparation and microwave dielectric properties of 3ZnO·B2O3 ceramics with low sintering temperature

The preparation and dielectric properties of 3ZnO·B₂O₃ ceramics were investigated. Dense 3ZnO·B₂O₃ ceramics were obtained as sintered in the temperature range from 950 to 1000 °C for 3 h. The X-ray diffraction showed that the obtained ceramics were of a monoclinic 3ZnO·B₂O₃ structure. The ceramic specimens fired at 955 °C for 1 h exhibited excellent microwave dielectric properties: ?_r ∼ 6.9, Q × f ∼ 20,647 GHz (@6.35 GHz), and τ_f ∼ −80 ppm/°C. The dependences of relative density, ?_r, and Q × f of ceramics sintered at 955 °C on sintering soaking time showed that they all reached their plateaus as the soaking time was up to 60 min. Meanwhile, 3ZnO·B₂O₃ ceramics had no reaction with silver during cofiring, indicating it is a potential candidate for low-temperature cofired ceramic (LTCC) substrate.