Structural, magnetic and electrical properties of (La0.70−xNdx)Sr0.30Mn0.70Cr0.30O3 with 0 ≤ x ≤ 0.30

The structural, magnetic and electrical properties of (La_0.70−xNd_x)Sr_0.30Mn_0.70Cr_0.30O₃ perovskites (0 ≤ x ≤ 0.30) prepared by the usual ceramic procedure were investigated. Structural Rietveld refinement revealed that these compounds crystallize in a rhombohedral perovskite structure when x = 0, 0.10 and 0.20, while for x = 0.30 the structure becomes orthorhombic (Pbnm). It was found that the substitution of La by Nd reduces the Curie temperature (T_C). The FC, ZFC, M(H) and AC susceptibility measurements show typical canted-antiferromagnetism for the Nd-doped samples, in which a ferromagnetic component coexists with predominant antiferromagnetic interactions. The values of the magnetization (M(H)) decrease very slightly when increasing the Nd content, compared to the undoped sample (M_S values at 5 T and 2 K are, respectively, 47.9, 47.3 and 47.5 emu/g for x = 0.10, 0.20 and 0.30, compared to 48.2 emu/g for x = 0), indicating that the Nd³⁺ contribution is negligible compared to the total moment of the ferromagnetic (Mn/Cr) network. The resistivity increases by several orders of magnitude with Nd-doping and the semi-conducting behaviour persists in the whole temperature range. The interaction between Mn⁴⁺–O–Cr³⁺and Cr³⁺–O–Cr³⁺ is responsible for the semi-conducting state.     

Investigation of the dependency of the upper critical magnetic field on the content x in Y1−xYbx/2Gdx/2Ba2Cu3O7−y superconducting structures

The Y_1−xYb_x/2Gd_x/2Ba₂Cu₃O_7−y superconducting samples for x = 0.0, 0.2, 0.4, 0.6, 0.8 and 1.0 were prepared by using the solid-state reaction technique. Resistivity measurements of the samples were performed in QD–PPMS system under different magnetic fields up to 5 T in zero fields cooling regime. Using the resistivity data, the upper critical magnetic field H_c2(0) at T = 0 K for 50% of R_n was calculated by the extrapolation H_c2(T) to the temperature T = 0 K. The coherence length in T = 0 K were calculated from H_c2(0) and the effects of x in the composition on both the coherence length and the upper critical magnetic field were examined. The results showed that H_c2(0) varied from 84.05 to 122.26 T with the content x. The upper critical magnetic field in the temperature T = 0 K slightly decreased with increasing the content x. Using the content x, the upper critical magnetic field can be controlled and this can be used in the superconductivity applications.     

The influence of gallium on the magnetocaloric properties of Gd5Si2Ge2

Gd₅Si₂Ge₂ was alloyed with varying amounts of Ga to study its influence on the giant magnetocaloric effect. Investigations on Gd₅(Si_2−xGe_2−x)Ga_2x with 2x = 0.03, 0.05 and 0.13 were carried out using X-ray powder diffraction, temperature and magnetic field dependent magnetization measurements, and differential scanning calorimetry. We observe that as the Ga content increases, the temperature stability range of the monoclinic phase narrows, and the orthorhombic structure gains stability. This is expected to be related to the decrease in the (Si/Ge)(Si/Ge) bond distance in the monoclinic phase. The maximum entropy change for the parent compound at 270 K was found to be 9.8 J kg⁻¹ K⁻¹ in an applied field of 5 T. For 2x = 0.03, this value reduces to 8.5 J kg⁻¹ K⁻¹, and the temperature corresponding to the maximum entropy change shifts marginally to 278 K. For other 2x values, the maximum entropy change further decreases.     

Studies on structural and electrical properties of Co1−xNixFe1.9Mn0.1O4 ferrite

Nickel-doped iron-deficient cobalt ferrite with small amount of manganese having the chemical composition Co_1−xNi_xFe_1.9Mn_0.1O₄, with x = 0.2, 0.4, 0.6 and 0.8, were prepared by standard double sintering ceramic method. The spinel phase formation was confirmed by X-ray diffraction (XRD). The DC resistivity measurements with temperature indicate a semiconducting behavior showing a linear decrease with increasing temperature and the doping of Ni enhances the resistivity. Maximum resistivity of the order of 10⁹ Ω cm was found for composition x = 0.8. Room temperature dielectric constant measurements with frequency (100 Hz to 1 MHz), show usual dielectric dispersion. Also, the variation of room temperature AC conductivity as a function of frequency were studied and explained by using Maxwell–Wagner two-layer model. The studies on dielectric constant (′), loss tangent (tan δ) and AC conductivity (σ_AC), at four different frequencies (viz., 1, 10, 100 kHz and 1 MHz), with temperature were made.     

Magnetic and structural properties of the chromium-based Mn1−xCdxCr2S4 thiospinel

The (Mn_1−xCd_x)Cr₂S₄ phases (0 ≤ x ≤ 0.6) have been synthesized from the corresponding elements at 1123 K. These samples were characterized by powder X-ray diffraction (XRD) and magnetic susceptibility. The (Mn_1−xCd_x)Cr₂S₄ compounds crystallize in the space group Fd-3m with cell parameters a = 10.101(6) Å, 10.139(3) Å, 10.165(2) Å, and 10.192(1) Å for x = 0, 0.2, 0.4 and 0.6, respectively. An overall ferrimagnetic behavior is observed for all samples. The ferromagnetic component increases rapidly when manganese is substituted by non-magnetic cadmium, as shown by ZFC/FC measurements. At the same time, the value of the magnetization M₅₀ at 50 kOe, deduced from M(H) loops, also increases with increasing cadmium content because the antiferromagnetic alignment between chromium and manganese spins is progressively lost, leading toward well aligned moments pointing into the same direction. These results are explained by a rearrangement of the chromium spins when Mn located at the tetrahedral sites, is substituted by Cd.     

Dielectric and magnetic properties of 0.7Bi(Fe1−xCrx)O3–0.1BaTiO3–0.2PbTiO3 solid solutions

0.7Bi(Fe_1−xCr_x)O₃–0.1BaTiO₃–0.2PbTiO₃ (x = 0, 0.1, 0.2, 0.3) solid solutions were prepared by the traditional ceramic process. X-ray diffraction results revealed that the samples with x = 0–0.3 showed pure perovskite structure. Frequency and temperature dependences of dielectric constants and dielectric loss of the samples were investigated. Both dielectric constant and the loss tangent increased at given frequencies (100 Hz–1 MHz), while the Curie temperature of the solid solutions decreased with increasing Cr content. Room temperature magnetic hysteresis loops indicated that an appropriate amount of Cr could improve magnetization of the solid solutions.     

Thermoelectric properties of Sn1−x−yTiySbxO2 ceramics

Thermoelectric properties of Sn_1−x−yTi_y Sb_xO₂ ceramics were investigated in detail. The addition of Sb into SnO₂ matrix increased the electric conductivity, σ. The increase in the σ value should be caused by the increase in the carrier concentration. The Seebeck coefficients of all the samples were negative, which means that these samples have n-type conduction. The samples of this study have porous structure. The maximum Z value of all the samples measured in this study was 2.4 × 10⁻⁵ K⁻¹.     

Phase transition-induced high electromechanical activity in [(K0.5Na0.5)1−xLix](Nb0.8Ta0.2)O3 lead-free ceramic system

A high electromechanical activity is observed in the [(K_0.5Na_0.5)_1−xLi_x](Nb_0.8Ta_0.2)O₃ (x = 0, 0.02, and 0.03) lead-free ceramic system at and around the orthorhombic (O)–tetragonal (T) phase transition temperature (T_O–T). This activity is found to originate from an O–T phase transition region at ambient temperature rather than a classical morphotropic phase boundary (MPB) region intrinsic in the Pb(Zr_1−xTi_x)O₃ (PZT) lead-based ceramic system. Li modification enables a large decrease in T_O–T instead of constituting a classical MPB. In contrast to the nearly temperature-independent classical MPB behavior in the PZT system, the strong temperature-dependent phase transition behavior in the system may impose a challenge to temperature demanding applications.     

Effect of Pt on the superconducting and magnetic properties of ErNi2B2C

We show that the variation of T_c in Er(Ni_1−xPt_x)₂B₂C (T_c  10.6 K and T_N  5.7 K for x = 0) as a function of x proceeds in two steps: strong decrease of T_c for initial values of x (0 ≤ x < 0.10, T_c = 7.3 K at x = 0.1) and, thereafter, a relatively much weaker drop (almost a plateau) of T_c with further increase of x. T_N exhibits a slight, almost linear, decrease over the entire range of x studied here; T_N = 4.7 K for x = 0.2. Our results for x = 0.10 are in sharp disagreement with the results, namely, T_c < T_N, as reported by Felner et al. [I. Felner, D. Schmitt, B. Barbara, C. Godart, E. Alleno, J. Solid State Chem. 133 (1997), 5].     

A novel proton conducting Ba0.95K0.05Ce0.6Zr0.2Gd0.16Zn0.04O3−δ for SOFC

A new proton conducting Ba_0.95K_0.05Ce_0.6Zr_0.2Gd_0.16Zn_0.04O_3−δ electrolyte membrane was prepared on NiO-based anode support by suspension spray followed by a co-sintering at 1400 °C for 4 h. Chemical stability test shows that this new proton conductor displays adequate chemical stability against CO₂ at intermediate temperatures. The conductivity of Ba_0.95K_0.05Ce_0.6Zr_0.2Gd_0.16Zn_0.04O_3−δ in humidified H₂ is about 50% higher than that of BaCe_0.6Zr_0.2Gd_0.16Zn_0.04O_3−δ from 500 to 800 °C. With La_0.8Sr_0.2MnO_3−δ cathode, fuel cell with Ba_0.95K_0.05Ce_0.6Zr_0.2Gd_0.16Zn_0.04O_3−δ electrolyte shows 1.02 V of OCV and 354 mW/cm² of maximum power density at 700 °C, respectively. And the cell performance did not degrade after running at least for 10 h.     

Fabrication and study on Ni1−xFexO-YSZ anodes for intermediate temperature anode-supported solid oxide fuel cells

Bimetal oxides Ni_1−xFe_xO (x = 0.01, 0.04, 0.08, 0.1, 0.15, 0.2, 0.4, 0.5) were synthesized and studied as anodes for intermediate temperature solid oxide fuel cells (SOFCs) based on yttria-stabilized zirconia (YSZ) film electrolyte. A single cell consisted of Ni_1−xFe_xO-YSZ anode, YSZ electrolyte film, LSM–YSZ composite cathode was prepared and tested at the temperature from 600 °C to 850 °C with humidified hydrogen (75 ml min⁻¹) as fuel and ambient air as oxidant. It was found that the cell with Ni_0.9Fe_0.1O-YSZ anode showed the highest power density, 1.238 W cm⁻² at 850 °C, among the cells with different anode composition. The promising performance of Ni_1−xFe_xO as anode suggests that bimetal anodes are worth studied for SOFCs in future.     

Structure, microstructure and electrical properties of (1 − x − y)Bi0.5Na0.5TiO3–xBi0.5K0.5TiO3–yBi0.5Li0.5TiO3 lead-free piezoelectric ceramics

The ternary system (1 − x − y)Bi_0.5Na_0.5TiO₃–xBi_0.5K_0.5TiO₃–yBi_0.5Li_0.5TiO₃ (abbreviated to BNKLT-x/y) was synthesized by conventional oxide-mixed method. The phase structure, microstructure, and dielectric, ferroelectric and piezoelectric properties of the ceramics were investigated. The X-ray diffraction patterns showed that pure perovskite phase with rhombohedral structure can be obtained in all the ceramics. The grain size varied with x and y. The temperature dependence of dielectric constant and dielectric loss revealed there were two phase transitions which were from ferroelectric (tetragonal) to anti-ferroelectric (rhombohedral) and anti-ferroelectric to paraelectric (cubic). Either increasing x or y content can make T_m (the temperature at which dielectric constant _r reaches the maximum) increase. With the addition of Bi_0.5K_0.5TiO₃, the remanent polarization P_r increased but the coercive field E_c decreased. With the addition of Bi_0.5Li_0.5TiO₃, P_r increased obviously and E_c increased slightly. Due to the stronger ferroelectricity by modifying Bi_0.5K_0.5TiO₃ and Bi_0.5Li_0.5TiO₃, the piezoelectric properties were enhanced at x = 0.22 and y = 0.10, which were as follows: P_r = 31.92 μC/cm², E_c = 32.40 kV/cm, _r = 1118, tan δ = 0.041, d₃₃ = 203 pC/N and K_p = 0.31. The results show that the BNKLT-x/y ceramics are promising candidates for the lead-free materials.     

Crystal structure, thermal expansion and electrical properties of the new Al0.32ErGe2 compound

A new ternary compound Al_0.32ErGe₂ has been synthesized and studied from 298 K to 773 K using X-ray powder diffraction technique. Its structure has been determined at room temperature by Rietveld refinement of X-ray powder diffraction data. The ternary compound Al_0.32ErGe₂ crystallizes in the orthorhombic with the defect CeNiSi₂ structure type (space group Cmcm, a = 0.40701(2) nm, b = 1.60401(9) nm, c = 0.39240(2) nm, Z = 4 and D_calc = 8.326 g/cm³). The average thermal expansion coefficients , and of Al_0.32ErGe₂ are 1.72 × 10⁻⁵ K⁻¹, 1.11 × 10⁻⁵ K⁻¹ and 1.52 × 10⁻⁵ K⁻¹, respectively. The bulk thermal expansion coefficient is 4.35 × 10⁻⁵ K⁻¹. Electrical resistivity of Al_0.32ErGe₂ was measured between 5 K and 300 K.     

Magnetic ordering and magnetic properties of ErAuxNi1−xIn (0 ≤ x ≤ 1) solid solution

The ErAu_xNi_1−xIn (0 ≤ x ≤ 1) quasiternary compounds crystallize in the hexagonal layered crystal structure of ZrNiAl-type. ErAuIn was reported to be an antiferromagnet with T_N = 3 K and magnetic moments having triangular arrangement within the basal plane (the magnetic order is described by the propagation vector ). On the contrary ErNiIn is a ferromagnet with T_C = 9 K and magnetic moments pointing along the c-axis. The magnetic ordering in ErAu_xNi_1−xIn (0 < x < 1) solid solution, has been investigated by neutron diffractometry in the temperature range between 1.5 and 15 K. Moreover, bulk magnetic measurements have been carried out in the range 1.72–400 K. All alloys of intermediate composition were found to be antiferromagnets with T_N between 4.6 and 7 K. Below 2 K their magnetic order is described by the propagation vector and magnetic moments are aligned along the c-axis. However, for alloys with 0.2 ≤ x ≤ 0.7 the propagation vector was found to turn into with increasing temperature.     

Thermoelectric properties of novel skutterudites with didymium: DDy(Fe1−xCox)4Sb12 and DDy(Fe1−xNix)4Sb12

In order to improve the thermoelectric properties via efficient phonon scattering Didymium (DD), a mixture of Pr and Nd, was used as a new filler in ternary skutterudites (Fe_1−xCo_x)₄Sb₁₂ and (Fe_1−xNi_x)₄Sb₁₂. DD-filling levels have been determined from combined data of X-ray powder diffraction and electron microprobe analyses (EMPA). Thermoelectric properties have been characterized by measurements of electrical resistivity, thermopower and thermal conductivity in the temperature range from 4.3 to 800 K. The effect of nanostructuring in DD_0.4Fe₂Co₂Sb₁₂ was elucidated from a comparison of both micro-powder (ground in a WC-mortar, 10 μm) and nano-powder (ball-milled, 150 nm), both hot pressed under identical conditions. The figure of merit ZT depends on the Fe/Co and Ni/Co-contents, respectively, reaching ZT > 1. At low temperatures the nanostructured material exhibits a higher thermoelectric figure of merit. The Vickers hardness was measured for all samples being higher for the nanostructured material.     

Lattice parameter values and phase transitions for the Cu2Cd1−zMnzSnSe4 and Cu2Cd1−zFezSnSe4 alloys

X-ray powder diffraction measurements and differential thermal analysis (DTA) were made on polycrystalline samples of the Cu₂Cd_1−zMn_zSnSe₄ and Cu₂Cd_1−zFe_zSnSe₄ alloy systems. The diffraction patterns were used to show the equilibrium conditions and to derive lattice parameter values. For Cu₂Cd_0.8Fe_0.2SnSe₄ as well as for Cu₂Cd_0.2Fe_0.8SnSe₄ the crystal structures were refined using the Rietveld method. It was found that the internal distortion parameter σ decreases as Cd is replaced by either Mn and/or Fe. For the Cu₂Cd_1−zMn_zSnSe₄ and Cu₂Cd_1−zFe_zSnSe₄ alloy systems, only two single solid phase fields, the tetragonal stannite α and the wurtz–stannite δ (Pmn2₁) structures were found to occur in the diagram. In addition to the tetragonal stannite α phase extra X-ray diffraction lines due to MnSe and/or FeSe₂ were observed for as grown samples in the range 0.7 < z < 1.0. However, it was found that the amount of the extra phase decreased for the compressed samples.     

Investigation of the microwave dielectric properties of Ca1−xMgxLa4Ti5O17 ceramics for application in coplanar patch antenna

In this paper, the dielectric properties of Ca_1−xMg_xLa₄Ti₅O₁₇ ceramics at microwave frequency have been studied. The diffraction peaks of Ca_(1−x)Mg_xLa₄Ti₅O₁₇ ceramics nearly unchanged with x increasing from 0 to 0.03. Similar X-ray diffraction peaks of Ca_0.99Mg_0.01La₄Ti₅O₁₇ ceramic were observed at different sintering temperatures. A maximum density of 5.3 g/cm³ can be obtained for Ca_0.99Mg_0.01La₄Ti₅O₁₇ ceramic sintered at 1500 °C for 4 h. A maximum dielectric constant (_r) and quality factor (Q × f) of Ca_0.99Mg_0.01La₄Ti₅O₁₇ ceramic sintered at 1500 °C for 4 h are 56.3 and 12,300 GHz (at 6.4 GHz), respectively. A near-zero temperature coefficient of resonant frequency (τ_f) of −9.6 ppm/°C can be obtained for Ca_0.99Mg_0.01La₄Ti₅O₁₇ ceramic sintered at 1500 °C for 4 h. The measurement results for the aperture-coupled coplanar patch antenna at 2.5 GHz are presented. With this technique, a 3.33% bandwidth (return loss <−10 dB) with a center frequency at approximately 2.5 GHz has been successfully achieved.     

dc-Magnetic susceptibility and EPR studies of vapour phase grown Cd1−xCoxTe crystals

Cd_1−xCo_xTe crystals (x = 0.001, 0.003, 0.005, 0.007 and 0.009) were grown by vapour phase technique. The grown diluted magnetic semiconducting (DMS) crystals were subjected to magnetization and dc-magnetic susceptibilities at room temperature. EPR spectra were recorded at 20 K for samples of all compositions. EPR spectra exhibited a broad resonance band around g  5.43. All the studies indicated the paramagnetic nature of the samples.     

Morphology, optical and magnetic properties of Zn1−xNixO nanorod arrays fabricated by hydrothermal method

Zn_1−xNi_xO (x = 0, 0.05, and 0.1) nanorod arrays were prepared by hydrothermal method. Morphology and structure analysis indicate that the nanorods have single-crystalline wurtzite structure, and no metallic Ni or NiO phase exists. Room temperature ferromagnetism (RTFM) was observed in the Zn_0.9Ni_0.1O nanorods. In addtion, photoluminescence spectra of Zn_1−xNi_xO (x = 0, 0.05, 0.1 and 0.2) samples exhibit near band edge UV emissions and orange-red emissions. And the orange-red emission is confirmed to have originated from the interstitial oxygen defects.