Practical aspects of lasing without inversion in various media

A rigorous density-matrix-based theory of lasing based on optically induced or autoionization-induced coherence between the levels is developed. The balance equations are obtained, and the conditions for lasing threshold are derived as a function of pumping strength and relaxation rates. Connection between the lasing without inversion and Raman and parametric processes is established. The main conclusion is that true CW lasing without inversion can indeed be obtained but only in a system where pumping and relaxation rates are favorable for attaining conventional lasing with population inversion. Practical implications of it, especially for the intersubband lasers, are discussed     

一种禁用鼠标条件下的键盘模拟研究与VC++实现

在一些具体工程实践中，特别在一些便携设备中，由于条件限制会禁止使用鼠标．这时必须考虑无鼠标条件下软件操作和显示效果的特殊性．VC^ 开发工具以有鼠标用户为默认用户，他的许多预先设置都是从有鼠标用户出发的。在编制无鼠标的软件时，许多方面必须重新考虑。     

Numerical Calculation of Mean Mission Duration

The purpose of this paper is to show how numerical integration can be used to calculate Mean Mission Duration (e.g., as required in MIL-STD-1543, Reliability Program Requirements for Space and Missile Systems). The accuracies, limitations, and applications of trapezoidal, Simpson's Rule, Weddle's Rule, and Gauss-Legendre numerical integration are discussed and a sample computer program for Weddle's Rule is presented. Weddle's Rule is shown to yield the most accurate results for hand calculators and those computers without preprogrammed routines while methods of the Gaussian type are shown to be the most accurate without regard for complexity of calculation.     

Global interconnect width and spacing optimization for latency, bandwidth and power dissipation

This paper addresses a novel methodology optimizing global interconnect width and spacing for International Technology Roadmap for Semiconductors technology nodes. Global interconnects with and without buffer insertion are considered. The effects of the width and spacing of global interconnects on performance, such as delay, bandwidth, total repeater area and energy dissipation, are analyzed. The product of delay and bandwidth is used as the figure of merit for simultaneous short latency and large bandwidth and the proposed methodology can optimize global interconnects for the maximal figure of merit. It is demonstrated that buffers should not be inserted in global interconnects if interconnect length is shorter than a critical length, which is a constant for a given technology. For global interconnects with buffer insertion, the optimal width and spacing have analytical expressions and are constants for a given technology. For global interconnects without buffer insertion, the optimal width and spacing are dependent on both the technology parameters and interconnect length and can be computed numerically.     

Use of adaptive fuzzy systems in parameter tuning of sliding-modecontrollers

The paper proposes to combine adaptive fuzzy systems with sliding-mode control (SMC) to solve the chattering problem of SMC for robotic applications. In the design of the controller, special attention is paid to chattering elimination without a degradation of the tracking performance. Furthermore, the a priori knowledge required of the system dynamics for design is kept to a minimum. The paper first considers the basic principles of sliding-mode and fuzzy controllers. Implementation difficulties and most popular solutions are then overviewed. Next, the design of a SMC reported in the literature is outlined and guidelines for the selection of controller parameters for the best tracking performance without chattering are presented. A novel approach based on the introduction of a "chattering variable" is developed. This variable, as a measure of chattering, is used as an input to an adaptive fuzzy system responsible for the minimization. Online tuning of parameters by fuzzy rules is carried out for the SMC. The experimental results obtained are given, and conclusions are presented     

Switching conditions for CMOS latch-up path with shunt resistances

Analytical expressions for the switching points of a one-dimensional p-n-p-n representation for a CMOS latch-up path are obtained without the traditional simplifying assumptions. A new criterion for the holding current is established. The results are applicable to the general case where the emitting junctions are shunted by resistances, as well as the simple p-n-p-n structure. The "holding current" of the path is discussed in some detail and predicted values are compared to those obtained experimentally.     

骨架式光纤带光缆用于FTTH的解决方案

将骨架式光纤带光缆用于FTTH的解决方案是将接人用的光纤带光缆中的光纤从机房连到若干交接箱,再接入各住宅单元,并根据住宅单元的不同结构选择所需接入的骨架式光纤带光缆.通过在骨架式光纤带光缆上开启若干分离窗口就可直接抽出需要接入住户的光纤带,而不必按通常的方式将光缆剪断,因无需接续且只需极少量的光缆,加上骨架式光纤带光缆无油膏填充的特点,极大地简化和方便了FTTH的设计和施工.     

Improved InP/InGaAs/InP PIN detector response using a transparent conductor contact

The elimination of the spatial variation in the frequency response of large area pin photodetectors is described using indium tin oxide as a transparent contact. The I/V, C/V, and relative frequency response characteristics are reported for devices fabricated with and without the indium tin oxide. The devices have active area diameters of 25.0 and 80.0 mu m. Responsivities were 0.53 and 0.61 A/W for photodetectors with and without the ITO contact, respectively.<>     

Simplified Analysis of Coupled Transmission-Line Networks

A relatively simple method is presented for analyzing coupled transmission-line networks by using network graphs and graph transformations. The network graph symbolism is easy to draw and to manipulate. All the graphs consist only of inductor, capacitor, and transformer symbols, and straight lines, which represent unit elements. The method of analysis is illustrated by several two-wire-line and multiwire-line examples. Also presented are several new useful transmission-line transformations and a graph equivalent for the general coupled transmission-line network. The graph-transformation method has four principal advantages: 1) explicit open-wire-line equivalent circuits of coupled line networks can be obtained relatively easily and without knowledge of network synthesis techniques; 2) the form of equivalent circuits can often be obtained without using any algebra; 3) at each step of the analysis, a positive-real network in graph form is available; consequently, in many analysis problems several equivalent circuits for the same network are derived; and 4) multiport networks are as easily dealt with as two-port networks.     

Coherence-collapse threshold of 1.3-/spl mu/m semiconductor DFB lasers

The onset of the coherence-collapse threshold is theoretically and experimentally studied for monomode 1.3-/spl mu/m antireflection/high reflection distributed-feedback lasers taking into account facet phase effects. The variation of the coherence collapse from chip to chip due to the facet phase is in the range of 7 dB and remains almost independent of the grating coefficient. Lasers that operate without coherence collapse under -15-dB optical feedback, while exhibiting an efficiency as high as 0.30 W/A, are demonstrated. Such lasers are adequate for 2.5 Gb/s isolator-free transmission without under the International Telecommunication Union recommended return loss.     

Large signal behavior of high power traveling-wave amplifiers

The results of an experimental investigation on the large signal behavior of a kilowatt power level helix type traveling-wave amplifier tube are presented. Operation with and without attenuators was investigated using a movable electromagnetic probe to measure power level along the tube. Quite different effects of drive power and beam voltage on the saturation level were found for operation with and without attenuators. The maximum power level is lower for attenuator operation. Also, power levels do not continue to increase with increasing beam voltage and drive power. In contrast, attenuator-less operation produces the highest efficiency, and the power levels continue to rise with increasing beam voltage and drive power. Conversion efficiencies as high as 25 per cent are obtained with an attenuator and as high as 40 per cent without an attenuator. Efficiency calculations based on small-signal theory can be made to agree reasonably well with the experimental attenuator-less operation efficiencies by assuming an appropriate ratio of the ac component of beam current to the dc component of beam current, i/I0.     

基于V93000的SoC中端口非测试复用的ADC和DAC IP核性能测试方案

 SoC(System-on-a-Chip)芯片设计中,由于芯片测试引脚数目的限制以及基于芯片性能的考虑,通常有一些端口不能进行测试复用的IP(Intellectual Property)核将不可避免地被集成在SoC芯片当中.对于端口非测试复用IP核,由于其端口不能被直接连接到ATE(Automatic Test Equipment)设备的测试通道上,由此,对端口非测试复用IP核的测试将是对SoC芯片进行测试的一个重要挑战.在本文当中,我们分别提出了一种基于V93000测试仪对端口非测试复用ADC(Analog-to-Digital Converter)以及DAC(Digital-to-Analog Converter)IP核的性能参数测试方法.对于端口非测试复用ADC和DAC IP核,首先分别为他们开发测试程序并利用V93000通过SoC芯片的EMIF(External Memory Interface)总线对其进行配置.在对ADC和DAC IP 核进行配置以后,就可以通过V93000捕获ADC IP 核采样得到的数字代码以及通过V93000 采样DAC IP 核转换得到的模拟电压值,并由此计算ADC以及DAC IP 核的性能参数.实验结果表明,本文分别提出的针对端口非测试复用ADC以及DAC IP 核测试方案非常有效.     

On coding without restrictions for the AWGN channel

Many coded modulation constructions, such as lattice codes, are visualized as restricted subsets of an infinite constellation (IC) of points in the n-dimensional Euclidean space. The author regards an IC as a code without restrictions employed for the AWGN channel. For an IC the concept of coding rate is meaningless and the author uses, instead of coding rate, the normalized logarithmic density (NLD). The maximum value C_∞ such that, for any NLD less than C_∞, it is possible to construct an PC with arbitrarily small decoding error probability, is called the generalized capacity of the AWGN channel without restrictions. The author derives exponential upper and lower bounds for the decoding error probability of an IC, expressed in terms of the NLD. The upper bound is obtained by means of a random coding method and it is very similar to the usual random coding bound for the AWGN channel. The exponents of these upper and lower bounds coincide for high values of the NLD, thereby enabling derivation of the generalized capacity of the AWGN channel without restrictions. It is also shown that the exponent of the random coding bound can be attained by linear ICs (lattices), implying that lattices play the same role with respect to the AWGN channel as linear-codes do with respect to a discrete symmetric channel     

In?Service SNR Estimation without Symbol Timing Recovery for QPSK Data Transmission Systems

In this paper we consider the problem of estimating the signal-to-noise ratio (SNR) of the received signal in a QPSK data transmission system. This estimation must be done in-service (non-data aided), without carrier phase knowledge and without symbol timing phase knowledge. New algorithms with these features are derived from the ratio of two moments. The performance of these algorithms is studied by means of simulations, and it is shown that they are robust against carrier and symbol timing frequency offsets as well. This makes them suitable for a wide range of applications.     

Spectral Efficiency Evaluation for MRC Diversity Schemes Over Generalized Rician Fading Channels

In this paper, closed-form expressions for the capacities per unit bandwidth for generalized Rician fading channels are derived for power and rate adaptation, constant transmit power, channel inversion with fixed rate, and truncated channel inversion adaptation policies. The closed-form solutions are derived for the single antenna reception (without diversity combining) and maximal-ratio combining (MRC) diversity cases. Truncated channel inversion adaptation policy is the best policy for the single antenna reception case, while the channel inversion with fixed rate policy is the best policy for the MRC diversity case. Constant transmit power policy provides the lowest spectral efficiency as compared to the other policies with and without diversity.     

Characterization and performance comparison of ripple-based control for voltage regulator modules

Three recently developed control methods for voltage regulator modules, namely, V/sup 2/ control, enhanced V/sup 2/ control, and enhanced V/sup 2/ control without output voltage dynamic feedback, are analyzed and compared in this paper. All three methods utilize the output voltage switching ripple for pulse-width modulation (PWM), hence, are collectively referred to as ripple-based control. A general modeling method based on the Krylov-Bogoliubov-Mitropolsky ripple estimation technique is applied to develop averaged models for single-channel as well as multichannel buck converters employing each of the control methods. Unlike existing models that are limited to small-signal operation, the proposed models are valid for large-signal operation and are capable of predicting subharmonic instability without including any sample-and-hold block as used in previous models. The paper also shows that adding parallel, high-quality ceramic capacitors at the output, which are ignored in previous models, can lead to pulse skipping and ripple instability, and a solution based on proper selection of the ceramic capacitors and/or ramp compensation at the PWM is presented. The models are further applied to analyze and compare the performance of the three control methods in terms of ripple stability, effective load current feedforward gain, and output impedance.     

Design of high-speed bipolar flip-flops for reduced clock loading

A new topology for flip-flops is presented. A current amplifier is incorporated into a standard, current mode logic, D-type flip-flop. The gain cell effectively buffers the clock without requiring additional current. Level shifting emitter followers from the clock are reduced in size and current. The frequency response of the gain cell selectively applies a keep-alive current to the circuit at high frequency without distorting low frequency outputs. The flip-flop is configured as a static frequency divider and compared to a standard flip-flop in a bipolar SiGe process. The new circuit is faster and requires less clock power at high frequency, making it suitable for large-scale integration.     

Monolithically integrated transverse-junction-stripe laser with anexternal waveguide in GaAs/AlGaAs

This device consists of a five-layer transverse-junction-stripe laser structure monolithically integrated with an external three-layer waveguide. The transverse p-n junction within the laser cavity permits the use of a vertical p-n junction in the external waveguide for future implementation of a modulator without disturbing the laser operation. As a result, this structure allows for flexibility in the design of the external waveguide/modulator without resorting to complicated regrowth procedures. Design curves for two different types of optical cavities are presented, and the reflectivity and transmission of the etched facet as a function of active layer thickness is modeled in detail using an excitation field approach. Finally, integrated laser/waveguide devices are fabricated based on this design and are compared to the theoretical curves. Most devices had threshold currents between 60 and 80 mA, while laser-to-waveguide transmission coefficients were as high as 38%     

Design of DPCM Quantizers for Video Signals Using Subjective Tests

The application of differential pulse code modulation (DPCM) for broadcast color television signals requires a design which produces no visible impairments under normal viewing conditions. This paper describes a quantizer design which is based on measured visibility thresholds of the various kinds of DPCM impairments such as granular noise, edge busyness, and slope overload. The visibility thresholds are determined by subjective tests based on comparisons of DPCM and PCM encoded pictures. Constructions of quantizers are carried out such that the number of levels is minimized without exceeding the measured visibility thresholds. Besides nonadaptive quantizers, adaptive quantizers are also constructed which are controlled by the signal changes of surrounding picture elements. These investigations show that for component coding of color video signals with two-dimensional prediction, a transmission rate of 31.7 Mbits/s is possible for natural types of test pictures without visible impairments using constant word length coding.