A 10.7-MHz sixth-order SC ladder filter in 0.35-/spl mu/m CMOS technology

A sixth-order 10.7-MHz bandpass switched-capacitor filter based on a double terminated ladder filter is presented. The filter uses a multipath operational transconductance amplifier (OTA) that presents both better accuracy and higher slew rate than previously reported Class-A OTA topologies. Design techniques based on charge cancellation and slower clocks are used to reduce the overall capacitance from 782 down to 219 unity capacitors. The filter's center frequency and bandwidth are 10.7 MHz and 400 kHz, respectively, and a passband ripple of 1 dB in the entire passband. The quality factor of the resonators used as filter terminations is around 32. The measured (filter + buffer) third-intermodulation (IM3) distortion is less than -40 dB for a two-tone input signal of +3-dBm power level each. The signal-to-noise ratio is roughly 58 dB while the IM3 is -45 dB; the power consumption for the standalone filter is 42 mW. The chip was fabricated in a 0.35-/spl mu/m CMOS process; filter's area is 0.84 mm/sup 2/.     

A 92-MHz 13-bit IF digitizer using optimized SC integrators in 0.35-/spl mu/m CMOS technology

A feedforward compensation scheme with no Miller capacitors is proposed to overcome the bandwidth limitations of traditional Miller compensation schemes. The technique has been used in the design of an operational transconductance amplifier (OTA) with a dc gain of 80 dB, gain bandwidth of 1.4 GHz, phase margin of 62/spl deg/, and 2 ns settling time for 2-pF load capacitor in a standard 0.35-/spl mu/m CMOS technology. The OTA's current consumption is 4.6 mA. The OTA is used in the design of a fourth-order switched-capacitor bandpass /spl Sigma//spl Delta/ modulator with a clock frequency of 92 MHz. It achieves a peak signal-to-noise ratio of 80 and 54 dB for 270-kHz (GSM) and 3.84-MHz (CDMA) bandwidths, respectively and consumes 19 mA of current from a /spl plusmn/1.25-V supply.     

A 64-MHz clock-rate /spl Sigma//spl Delta/ ADC with 88-dB SNDR and -105-dB IM3 distortion at a 1.5-MHz signal frequency

A 64-MHz clock rate sigma-delta (/spl Sigma//spl Delta/) analog-to-digital converter (ADC) with -105-dB intermodulation distortion (IMD) at a 1.5-MHz signal frequency is reported. A linear replica bridge sampling network enables the ADC to achieve high linearity for high signal frequencies. Operating at an oversampling ratio of 29, a 2-1-1 cascade with a 2-b quantizer in the last stage reduces the quantization noise level well below that of the thermal noise. The measured signal-to-noise and distortion ratio (SNDR) in 1.1-MHz bandwidth is 88 dB, and the spurious-free-dynamic-range (SFDR) is 106 dB. The modulator and reference buffers occupy a 2.6-mm/sup 2/ die area and have been implemented with thick oxide devices, with minimum channel length of 0.35 /spl mu/m, in a dual-gate 0.18-/spl mu/m 1.8-V single-poly five-metal (SP5M) digital CMOS process. The power consumed by the ADC is 230 mW, including the decimation filters.     

A 2.2-mW CMOS bandpass continuous-time multibit /spl Delta/-/spl Sigma/ ADC with 68 dB of dynamic range and 1-MHz bandwidth for wireless applications

A delta-sigma (/spl Delta//spl Sigma/) analog-to-digital converter featuring 68-dB dynamic range and 64-dB signal-to-noise ratio in a 1-MHz bandwidth centered at an intermediate frequency of 2 MHz with a 48-MHz sample rate is reported. A second-order continuous-time modulator employing 4-bit quantization is used to achieve this performance with 2.2 mW of power consumption from a 1.8-V supply. The modulator including references occupies 0.36 mm/sup 2/ of die area and is implemented in a 0.18-/spl mu/m five-metal single-poly digital CMOS process.     

Highly linear 2.5-V CMOS /spl Sigma//spl Delta/ modulator for ADSL+

We present a 90-dB spurious-free dynamic range sigma-delta modulator (/spl Sigma//spl Delta/M) for asymmetric digital subscriber line applications (both ADSL and ADSL+), with up to a 4.4-MS/s digital output rate. It uses a cascade (MASH) multibit architecture and has been implemented in a 2.5-V supply, 0.25-/spl mu/m CMOS process with metal-insulator-metal capacitors. The prototypes feature 78-dB dynamic range (DR) in the 30-kHz to 2.2-MHz band (ADSL+) and 85-dB DR in the 30-kHz to 1.1-MHz band (ADSL). Integral and differential nonlinearity are within /spl plusmn/0.85 and /spl plusmn/0.80 LSB/sub 14 b/, respectively. The /spl Sigma//spl Delta/ modulator and its auxiliary blocks (clock phase and reference voltage generators, and I/O buffers) dissipate 65.8 mW. Only 55 mW are dissipated in the /spl Sigma//spl Delta/ modulator.     

A Power-Efficient Two-Channel Time-Interleaved ΣΔ Modulator for Broadband Applications

A two-channel time-interleaved second-order sigma-delta modulator for broadband applications including asymmetrical digital subscriber line (ADSL) is presented. The proposed two-channel SigmaDelta modulator uses a single integrator channel which does not require additional active elements for the quantizer input generation, since the integrator outputs are directly used as the input of the quantizers. As a result, the entire modulator can be implemented using only two op-amps, which is beneficial for both power consumption and area. Furthermore, this architecture is robust to channel mismatch effects and can operate with a simple clocking scheme. The SigmaDelta modulator achieves a dynamic range of 85 dB over a 1.1-MHz signal bandwidth with an effective clock frequency of 132 MHz. The circuit is implemented in 0.18-mum CMOS technology using metal-insulator-metal capacitors. The total power consumption of the SigmaDelta modulator is 5.4mW from a 1.8-V supply and occupies an active area of 1.1 mm²     

A third-order /spl Sigma//spl Delta/ modulator in 0.18-/spl mu/m CMOS with calibrated mixed-mode integrators

This paper describes a third-order sigma-delta (/spl Sigma//spl Delta/) modulator that is designed and implemented in 0.18-/spl mu/m CMOS process. In order to increase the dynamic range, this modulator takes advantage of mixed-mode integrators that consist of analog and digital integrators. A calibration technique is applied to the digital integrator to mitigate mismatch between analog and digital paths. It is shown that the presented modulator architecture can achieve a 12-dB better dynamic range than conventional structures with the same oversampling ratio (OSR). The experimental prototype chip achieves a 76-dB dynamic range for a 200-kHz signal bandwidth and a 55-dB dynamic range for a 5-MHz signal bandwidth. It dissipates 4 mW from 1.8-V supply voltages and occupies 0.7-mm/sup 2/ silicon area.     

A 4-MHz CMOS continuous-time filter with on-chip automatic tuning

A third-order elliptic low-pass continuous-time filter with a 4-MHz cutoff frequency, integrated in a 3-μm p-well CMOS process, is presented. The design procedure is based on the direct simulation of a doubly terminated LC ladder filter by capacitors and fully balanced, current-controlled transconductance amplifiers with extended linear range. The on-chip automatic tuning circuit uses a phase-locked loop implemented with an 8.5-MHz controlled oscillator that matches a specific two-integrator loop of the filter. The complete circuit features 70-dB dynamic range (THD<-50 dB) and consumes only 16 mW from ±2.5-V supplies     

A 3.3-mW /spl Sigma//spl Delta/ modulator for UMTS in 0.18-/spl mu/m CMOS with 70-dB dynamic range in 2-MHz bandwidth

A quadrature fourth-order, continuous-time, /spl Sigma//spl Delta/ modulator with 1.5-b quantizer and feedback digital-to-analog converter (DAC) for a universal mobile telecommunication system (UMTS) receiver chain is presented. It achieves a dynamic range of 70 dB in a 2-MHz bandwidth and the total harmonic distortion is -74 dB at full-scale input. When used in an integrated receiver for UMTS, the dynamic range of the modulator substantially reduces the need for analog automatic gain control and its tolerance of large out-of-band interference also permits the use of only first-order prefiltering. An IC including an I and Q /spl Sigma//spl Delta/ modulator, phase-locked loop, oscillator, and bandgap dissipates 11.5 mW at 1.8 V. The active area is 0.41 mm/sup 2/ in a 0.18-/spl mu/m 1-poly 5-metal CMOS technology.     

A 1.3-V 5-mW fully integrated tunable bandpass filter at 2.1 GHz in 0.35-/spl mu/m CMOS

A 2.1-GHz 1.3-V 5-mW fully integrated Q-enhancement LC bandpass biquad programmable in f/sub o/, Q, and peak gain is implemented in 0.35-/spl mu/m standard CMOS technology. The filter uses a resonator built with spiral inductors and inversion-mode pMOS capacitors that provide frequency tuning. The Q tuning is through an adjustable negative-conductance generator, whereas the peak gain is tuned through an input G/sub m/ stage. Noise and nonlinearity analyses presented demonstrate the design tradeoffs involved. Measured frequency tuning range around 2.1 GHz is 13%. Spiral inductors with Q/sub o/ of 2 at 2.1 GHz limit the spurious-free dynamic range (SFDR) at 31-34 dB within the frequency tuning range. Measurements show that the peak gain can be tuned within a range of around two octaves. The filter sinks 4 mA from a 1.3-V supply providing a Q of 40 at 2.19 GHz with a 1-dB compression point dynamic range of 35 dB. The circuit operates with supply voltages ranging from 1.2 to 3 V. The silicon area is 0.1 mm/sup 2/.     

IF-sampling fourth-order bandpass /spl Delta//spl Sigma/ modulator for digital receiver applications

Bandpass modulators sampling at high IFs (/spl sim/200 MHz) allow direct sampling of an IF signal, reducing analog hardware, and make it easier to realize completely software-programmable receivers. This paper presents the circuit design of and test results from a continuous-time tunable IF-sampling fourth-order bandpass /spl Delta//spl Sigma/ modulator implemented in InP HBT IC technology for use in a multimode digital receiver application. The bandpass /spl Delta//spl Sigma/ modulator is fabricated in AlInAs-GaInAs heterojunction bipolar technology with a peak unity current gain cutoff frequency (f/sub T/) of 130 GHz and a maximum frequency of oscillation (f/sub MAX/) of 130 GHz. The fourth-order bandpass /spl Delta//spl Sigma/ modulator consists of two bandpass resonators that can be tuned to optimize both wide-band and narrow-band operation. The IF is tunable from 140 to 210 MHz in this /spl Delta//spl Sigma/ modulator for use in multiple platform applications. Operating from /spl plusmn/5-V power supplies, the fabricated fourth-order /spl Delta//spl Sigma/ modulator sampling at 4 GSPS demonstrates stable behavior and achieves a signal-to-(noise + distortion) ratio (SNDR) of 78 dB at 1 MHz BW and 50 dB at 60 MHz BW. The average SNDR performance measured on over 250 parts is 72.5 dB at 1 MHz BW and 47.7 dB at 60 MHz BW.     

A 14-bit, 10-Msamples/s D/A converter using multibit /spl Sigma//spl Delta/ modulation

A 14-bit digital-to-analog converter based on a fourth-order multibit sigma-delta modulator is described. The digital modulator is pipelined to minimize both its power dissipation and design complexity. The 6-bit output of this modulator is converted to analog using 64 current-steering cells that are continuously calibrated to a reference current. This converter achieves 85-dB dynamic range at 5-MHz signal bandwidth, with an oversampling ratio of 12. The chip was fabricated in a 0.5-/spl mu/m CMOS technology and operates from a single 2.5-V supply.     

A 1.5-V 12-bit power-efficient continuous-time third-order /spl Sigma//spl Delta/ modulator

This paper presents the design strategy, implementation, and experimental results of a power-efficient third-order low-pass /spl Sigma//spl Delta/ analog-to-digital converter (ADC) using a continuous-time (CT) loop filter. The loop filter has been implemented by using active RC integrators. Several power optimizations, design requirements, and performance limitations relating to circuit nonidealities in the CT modulator are presented. The influence of the low supply voltage on the various building blocks such as the amplifier as well as on the overall /spl Sigma//spl Delta/ modulator is discussed. The ADC was implemented in a 3.3-V 0.5-/spl mu/m CMOS technology with standard threshold voltages. Measurements of the low-power 1.5-V CT /spl Sigma//spl Delta/ ADC show a dynamic range and peak signal-to-noise-plus-distortion ratio of 80 and 70 dB, respectively, in a bandwidth of 25 kHz. The measured power consumption is only 135 /spl mu/W from a single 1.5-V power supply.     

A 0.7-V MOSFET-only switched-opamp /spl Sigma//spl Delta/ modulator in standard digital CMOS technology

A 0.7-V MOSFET-only /spl Sigma//spl Delta/ modulator for voice band applications is presented. The second-order modulator is realized using a switched-opamp technique. All capacitors are realized using compensated MOS devices operated in the depletion region. A combination of parallel and series compensated depletion-mode MOSCAPs is used to obtain high area efficiency. The circuit is fabricated in a 0.18-/spl mu/m CMOS process. The only components used are standard n-MOS and p-MOS transistors with threshold voltages of approximately 400 mV. All transistors are operated within the supply voltage window of 0.7 V; voltage boosting techniques are not used. The active area is 0.082 mm/sup 2/. The modulator achieves 67-dB signal-to-noise-and-distortion ratio, 70-dB signal-to-noise ratio, and 75-dB dynamic range at 8-kHz signal bandwidth and consumes 80 /spl mu/W of power.     

Comparison frequency doubling and charge pump matching techniques for dual-band /spl Delta//spl Sigma/ fractional-N frequency synthesizer

The frequency synthesizer with two LC-VCOs is fully integrated in a 0.35-/spl mu/m CMOS technology. In supporting dual bands, all building blocks except VCOs are shared. A current compensation scheme using a replica charge pump improves the linearity of the frequency synthesizer and, thus, suppresses spurious tones. To reduce the quantization noise from a /spl Delta//spl Sigma/ modulator and the noise from the building blocks except the VCO, the proposed architecture uses a frequency doubler with a noise-insensitive duty-cycle correction circuit (DCC) in the reference clock path. Power consumption is 37.8 mW with a 2.7-V supply. The proposed frequency synthesizer supports 10-kHz channel spacing with the measured phase noise of -114 dBc/Hz and -141 dBc/Hz at 100-kHz and 1.25-MHz offsets, respectively, in the PCS band. The fractional spurious tone at 10-kHz offset is under -54 dBc.     

A cascaded continuous-time /spl Sigma//spl Delta/ Modulator with 67-dB dynamic range in 10-MHz bandwidth

This paper presents the design of a 2-2 cascaded continuous-time sigma-delta modulator. The cascaded modulator comprises two stages with second-order continuous-time resonator loopfilters, 4-bit quantizers, and feedback digital-to-analog converters. The digital noise cancellation filter design is determined using continuous-time to discrete-time transformation of the sigma-delta loopfilter transfer functions. The required matching between the analog and digital filter coefficients is achieved by means of simple digital calibration of the noise cancellation filter. Measurement results of a 0.18-/spl mu/m CMOS prototype chip demonstrate 67-dB dynamic range in a 10-MHz bandwidth at 8 times oversampling for a single continuous-time cascaded modulator. Two cascaded modulators in quadrature configuration provide 20-MHz aggregate bandwidth. Measured anti-alias suppression is over 50 dB for input signals in the band from 150 to 170 MHz around the sampling frequency of 160 MHz.     

A 25-MS/s 14-b 200-mW /spl Sigma//spl Delta/ Modulator in 0.18-/spl mu/m CMOS

The design of a fifth-order 4-b quantizer single-loop /spl Sigma//spl Delta/ modulator is presented that achieves 25-MS/s conversion rate with 84 dB of dynamic range and 82 dB of signal-to-noise ratio. Implemented in a 0.18-/spl mu/m CMOS technology, the 0.95-mm/sup 2/ chip has a power consumption of 200 mW from a 1.8-V supply.     

An I/Q-Channel Time-Interleaved Bandpass Sigma–Delta Modulator for a Low-IF Receiver

This brief proposes a multiplexing scheme to realize an I/Q-channel time-interleaved (TI) bandpass sigma-delta modulator that shares operational transconductance amplifiers to minimize power consumption and silicon area for a low-intermediate-frequency (IF) wireless receiver. The test chip was fabricated for a 10.7-MHz IF system with a 0.35-mum CMOS process. The measured peak signal-to-noise distortion ratio for a 200-kHz bandwidth is approximately 73 dB. The power consumption of the fabricated chip is 61 mW with a 3.3-V supply, and the silicon area is 1.78 mm². The measured channel crosstalk is about -48 dB     

A 1-MHz-bandwidth second-order continuous-time quadrature bandpass sigma-delta modulator for low-IF radio receivers

This paper presents a quadrature bandpass /spl Sigma//spl Delta/ modulator with continuous-time architecture. Due to the continuous-time architecture and the inherent anti-aliasing filter, the proposed /spl Sigma//spl Delta/ modulator needs no additional anti-aliasing filter in front of the modulator in contrast to quadrature bandpass /spl Sigma//spl Delta/ modulators with switched-capacitor architectures. The second-order /spl Sigma//spl Delta/ modulator digitizes complex analog I/Q input signals at 1-MHz intermediate frequency and operates within a clock frequency range of 25-100 MHz. The modulator chip achieves a peak signal-to-noise-distortion ratio (SNDR) of 56.7 dB and a dynamic range of 63.8 dB within a 1-MHz signal bandwidth and at a clock frequency of 100 MHz. Furthermore, it provides an image rejection of at least 40 dB. The 0.65-/spl mu/m BiCMOS chip consumes 21.8 mW at 2.7-V supply voltage.     

A 1-V 10.7-MHz switched-opamp bandpass /spl Sigma//spl Delta/ modulator using double-sampling finite-gain-compensation technique

A 1 V switched-capacitor (SC) bandpass sigma-delta (/spl Sigma//spl Delta/) modulator is realized using a high-speed switched-opamp (SO) technique with a sampling frequency of up to 50 MHz, which is improved ten times more than prior 1 V SO designs and comparable to the performance of the state-of-the-art SC circuits that operate at much higher supply voltages. On the system level, a fast-settling double-sampling SC biquadratic filter architecture is proposed to achieve high-speed operation. A low-voltage double-sampling finite-gain-compensation technique is employed to realize a high-resolution /spl Sigma//spl Delta/ modulator using only low-DC-gain opamps to maximize the speed and to reduce power dissipation. On the circuit level, a fast-switching methodology is proposed for the design of the switchable opamps to achieve a switching frequency up to 50 MHz. Implemented in a 0.35-/spl mu/m CMOS process (V/sub TP/=0.82 V and V/sub TN/=0.65 V) and at 1 V supply, the modulator achieves a measured peak signal-to-noise-and-distortion ratio (SNDR) of 42.3 dB at 10.7 MHz with a signal bandwidth of 200 kHz, while dissipating 12 mW and occupying a chip area of 1.3 mm/sup 2/.