Synthesis and properties of monomer casting polyamide 6/poly(methyl methacrylate) blends

We successfully synthesized monomer casting polyamide 6 (MCPA6)/poly(methyl methacrylate) (PMMA) blends in two steps: (1) radical polymerization of methyl methacrylate in ?‐caprolactam and (2) anionic ring‐opening polymerization of this ?‐caprolactam solution. The influence of PMMA on the crystallization behavior of MCPA6 was studied with differential scanning calorimetry and X‐ray diffraction, which showed that PMMA could act as a heterogeneous nucleation agent and favored the formation of the γ‐crystalline form. The rheological properties were also studied and indicated that PMMA reduced the interaction between MCPA6 chains by lowering the density of hydrogen bonding. This study used a novel and convenient method to prepare microporous MCPA6/PMMA particles that involved removing the continuous phase. Their surface area and thermal stability were characterized by the Brunauer–Emmett–Teller method and thermogravimetric analysis, respectively. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Thermal behavior and properties of polystyrene/poly(methyl methacrylate) blends

The thermal behavior and properties of immiscible blends of polystyrene (PS) and poly(methyl methacrylate) (PMMA) with and without PS‐b‐PMMA diblock copolymer at different melt blending times were investigated by use of a differential scanning calorimeter. The weight fraction of PS in the blends ranged from 0.1 to 0.9. From the measured glass transition temperature (T_g) and specific heat increment (ΔC_p) at the T_g, the PMMA appeared to dissolve more in the PS phase than did the PS in the PMMA phase. The addition of a PS‐b‐PMMA diblock copolymer in the PS/PMMA blends slightly promoted the solubility of the PMMA in the PS and increased the interfacial adhesion between PS and PMMA phases during processing. The thermogravimetric analysis (TGA) showed that the presence of the PS‐b‐PMMA diblock copolymer in the PS/PMMA blends afforded protection against thermal degradation and improved their thermal stability. Also, it was found that the PS was more stable against thermal degradation than that of the PMMA over the entire heating range. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 609–620, 2004     

Investigation of the structural,thermal, mechanical,and optical properties of poly(methyl methacrylate) and poly(vinylidene fluoride) blends

In this investigation, poly(methyl methacrylate) (PMMA) and poly(vinylidene fluoride) (PVDF) blends (w/w) were prepared in a Brabender (South Hackensack, NJ) plasticorder with a thermoplastic mixing chamber (type W60) preheated at 180°C. These blends were further converted into films by a conventional solution casting method and characterized with Fourier transform infrared spectroscopy, differential scanning calorimetry, X‐ray diffraction, mechanical property measurements, impact strength testing, ultraviolet–visible spectroscopy, refractive‐index measurements, and contact‐angle study. The Fourier transform infrared results indicated that the compatibility between these two systems resulted from hydrogen bonding between the carbonyl group of PMMA and the CH₂ group of PVDF. The thermal analysis showed depressions in the glass‐transition temperature, melting temperature, and crystallization temperature. The heat of crystallization increased with an increase in the PVDF content in the blend. An increase in the heat of crystallization meant an increase in the crystallinity. An increase in the cooling rate increased the crystallization rate. The improvement in the mechanical properties of the blend films indicated that the observed behavior was ascribable to a more coherent structure of the blends due to strong specific interactions between PMMA and PVDF chains. The impact strength analysis revealed a substantial increase in the impact strength from 21.64 to 38.52 J/m. Optical absorption spectra suggested the presence of an optical band gap energy that increased with an increase in the PVDF content in the blend. The contact angle against water increased with the PVDF content in the blend film, and this was caused by the hydrophobicity of PVDF due to the CF₂ group of PVDF. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Compatibility studies with blends based on poly(n‐butyl methacrylate) and polyacrylonitrile

In this study, poly(n‐butyl methacrylate) (PBMA) was prepared by a suspension polymerization process, and blending with polyacrylonitrile (PAN) in N,N‐dimethyl acetamide to prepare PAN/PBMA blends in various proportions. Hansen's three dimensional solubility parameters of PAN and PBMA were calculated approximately through the contributions of the structural groups. The compatibility in these blend systems was studied with theoretical calculations as well as experimental measurements. Viscometric methods, Fourier transform infrared spectroscopy, dynamic mechanical analysis, scanning electron microscopy, and thermogravimetric analysis were used for this investigation. All the results showed that a partial compatibility existed in PAN/PBMA blend system, which may be due to the intermolecular interactions between the two polymers. And, the adsorption experiment results showed that the addition of PBMA contributed to the enhancing adsorptive properties of blend fibers, which lays the foundation for further studying PAN/PBMA blend fibers with adsorptive function. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Hydrolytic stability of polylactide and poly(methyl methacrylate) blends

The hydrolytic stability of polylactide/poly(methyl methacrylate) (PLA/PMMA) blends prepared using a twin‐screw extrusion process was investigated. The effects of hydrolysis were monitored in neutral and alkaline media at 80 °C by tracking the changes in molecular weight distribution, weight loss, water uptake, and crystallization behavior. The crystallinity of PLA in blends prior to hydrolysis was shown to be largely hindered by the presence of PMMA. However, PLA recrystallized rapidly during hydrolysis. The PMMA in the blends was shown to provide increased hydrolytic and structural stability to the blends. In the neutral medium, the presence of PMMA delayed and reduced the weight loss but did not significantly affect PLA degradation kinetics. On the other hand, in the alkaline medium, the weight loss rate was strongly decreased in presence of PMMA and the kinetics of degradation was shown to be depend on PMMA content. The microstructure of these blends throughout the hydrolysis process was also examined by scanning electron microscopy. A porous structure, with interconnected pores in the 20–50 nm range, was developed due to the selective removal of PLA. Based on these morphological observations, erosion mechanism of PLA/PMMA blends was discussed. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45991.     

A high‐resolution solid‐state NMR investigation of molecular mobility of poly(methyl methacrylate)/poly(vinyl pyrrolidone)/poly(ethylene oxide) ternary blends

The ternary blends of poly(methyl methacrylate)/poly(vinyl pyrrolidone)/poly(ethylene oxide), PMMA/PVP/PEO, were prepared by melting process, using a Haake plastograph, and nuclear magnetic resonance spectroscopy (NMR) was used as a methodology to characterize the molecular mobility of blend components, because NMR has several techniques that allow us to evaluate polymeric materials in different time scales. The NMR results showed that the blends were miscible on a molecular level. The values of proton lattice relaxation time in the rotating frame (T₁ρH) indicate that the ternary blend interaction did not reduce the intermolecular distance, because it is dipole–dipole. The molecular motion of each component, even in the miscible amorphous phase and the addition of PEO, has a definitive effect on the PMMA molecular mobility. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1492–1495, 2006     

Compatibility in immiscible polysulfone/poly(ethylene terephthalate) blends

Polysulfone (PSU)/poly(ethylene terephthalate) (PET) blends were obtained by direct injection molding across the composition range. Their phase behavior, thermal properties, morphology, and mechanical properties were measured. The blends were composed of a pure PSU amorphous phase and either a pure PET phase in PSU‐poor blends, or a PET‐rich phase with some dissolved PSU in PSU‐rich blends. The morphology of the dispersed phase was mostly spherical with some elongated particles in the PET‐rich blends. A slight synergistic behavior was observed in the Young's modulus, mainly in the 90/10 blend, which is probably due to orientation effects. The presence of some broken particles indicated some interfacial adhesion. The ductility values were approximately linear with composition. This was generally the case in PSU‐rich blends, and was attributed to the higher level of PSU in the PET‐rich phase. Although embrittlement was seen in blends with 30% of the second component, the ductility of the two pure components did not significantly decrease after annealing due to the presence of low amounts (up to 10%) of another component of the blend. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2193–2200, 2004     

The reinforcement of polystyrene and poly(methyl methacrylate) interfaces using alternating copolymers

Asymmetric double cantilever beam studies are presented that document the ability of alternating copolymers to strengthen a polymer/polymer interface. For polystyrene/poly(methyl methacrylate) interfaces, these results show that the alternating copolymer is the least effective sequence distribution of a linear copolymer at strengthening the polystyrene/poly(methyl methacrylate) interface, where the copolymers that are compared all have similar molecular weight and composition. The results also demonstrate that the effect of copolymer molecular weight on the ability of the copolymer to strengthen an interface is controlled by the balance between the increased entanglements and decreased miscibility of the copolymer with the homopolymers with increasing molecular weight.     

Nonisothermal crystallization kinetics of poly(ethylene terephthalate) and poly(methyl methacrylate) blends

The nonisothermal crystallization kinetics of poly(ethylene terephthalate) (PET) and poly(methyl methacrylate) (PMMA) blends were studied. Four compositions of the blends [PET 25/PMMA 75, PET 50/PMMA 50, PET 75/PMMA 25, and PET 90/PMMA 10 (w/w)] were melt‐blended for 1 h in a batch reactor at 275°C. Crystallization peaks of virgin PET and the four blends were obtained at cooling rates of 1°C, 2.5°C, 5°C, 10°C, 20°C, and 30°C/min, using a differential scanning calorimeter (DSC). A modified Avrami equation was used to analyze the nonisothermal data obtained. The Avrami parameters n, which denotes the nature of the crystal growth, and Z_t, which represents the rate of crystallization, were evaluated for the four blends. The crystallization half‐life (t_½) and maximum crystallization (t_max) times also were evaluated. The four blends and virgin polymers were characterized using a thermogravimetric analyzer (TGA), a wide‐angle X‐ray diffraction unit (WAXD), and a scanning electron microscope (SEM). © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3565–3571, 2006     

Feather‐like morphology of poly(methyl methacrylate)/poly(ethylene oxide) blends: The effect of cooling rate and poly(methyl methacrylate) content

The effect of cooling rate on the crystallization morphology and growth rate of poly(ethylene oxide) (PEO) and PEO/poly(methyl methacrylate) (PMMA) blends has been observed by Hot Stage Polarized Microscopy (HS‐POM). The isothermal crystallization kinetics study was carried out by differential scanning calorimetry (DSC). The spherulite morphology has been observed for the neat PEO with molecular weight of 6000 g/mol. By adding of PMMA with molecular weight of 39,300 g/mol, the growth fronts become irregular. With the increasing of PMMA content, the irregularity of growth front becomes more obvious, and the feather‐like morphology can be observed. When PMMA content is 60%, the spherulite is seriously destroyed. This phenomenon is more obvious for the slow cooling process. Based on the measurement of spherulite, the growth rate curves were obtained. According to the curves, it can be seen that the growth rate decreases with the increasing of PMMA content, and the growth rate during the slow cooling process is higher than that of the fast cooling process. The isothermal crystallization experiment indicates that the crystallization rate decreases dramatically with the increasing of PMMA content. And the Avrami parameter n was obtained, which is non‐integral and less than 3. Finally, it can be concluded that the higher value of n can be obtained for the condition with low crystallization rate. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41705.     

Phase continuity and inversion in polystyrene/poly(methyl methacrylate) blends

Dual-phase continuity and phase inversion of polystyrene (PS)/poly(methyl methacrylate) (PMMA) blends processed in a twin-screw extruder was investigated using a selective extraction technique and scanning electron microscopy. Emphasis was placed on investigating the effects of viscosity ratio, blend composition, processing variables (mixing time and annealing) and diblock copolymer addition on the formation of bi-continuous phase structure (BPS) in PS/PMMA blends. The experimental results were compared with the volume fraction of phase inversion calculated with various semi-empirical models. The results showed that the formation of a BPS strongly depends on the blend composition and the viscosity ratio of the constituent components. Furthermore, BPS was found in a wide volume fraction interval. Increasing the mixing time and the addition of diblock copolymer, both led to a narrowing range of volume fraction in which BPS exists. Quiescent annealing coarsened the structure but indicated no qualitative changes. Some model predictions for phase inversion could predict qualitative aspects of the observed windows of co-continuity but none of the models could account quantitatively for the observed data.     

Thermal and mechanical properties of poly(methyl methacrylate) and ethylene vinyl acetate copolymer blends

A series of poly(methyl methacrylate) (PMMA) blends have been prepared with different compositions viz., 5, 10, 15, and 20 wt % ethylene vinyl acetate (EVA) copolymer by melt blending method in Haake Rheocord. The effect of different compositions of EVA on the physico‐mechanical and thermal properties of PMMA and EVA copolymer blends have been studied. Differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA) and thermogravimetric analysis (TGA) has been employed to investigate the phase behavior of PMMA/EVA blends from the point of view of component specific interactions, molecular motions and morphology. The resulting morphologies of the various blends also studied by optical microscope. The DSC analysis indicates the phase separation between the PMMA matrix and EVA domains. The impact strength analysis revealed a substantial increase in impact strength from 19 to 32 J/m. The TGA analysis reveals the reduction in onset of thermal degradation temperature of PMMA with increase in EVA component of the blend. The optical microscope photographs have demonstrated the PMMA/EVA system had a microphase separated structure consisting of dispersed EVA domains within a continuous PMMA matrix. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Study of polymer blends of poly(acetylene) with poly(methyl methacrylate) and methyl methacrylate-butadiene-styrene copolymer

Summary Electroactive polymer blends of polyacetylene (PA) with poly (methyl methacrylate) (PMMA) or methyl methacrylate-butadien-styrene (MBS) copolymer were prepared in situ as free-standing films or powders by polymerization of acetylene in the presence of PMMA or MBS-copolymer, using Luttinger's catalyst. Blends of different composition were studied by infrared spectroscopy and electrical conductivity measurements. Environmental stability of pristine and doped PA was improved to some extent in the presence of PMMA.     

Comparison of the phase behaviour of the liquid-crystalline polymer/poly(methyl methacrylate) and poly(vinyl acetate)/poly(methyl methacrylate) blends

The phase behaviour of blends of a liquid-crystalline polymer (LCP) and poly(methyl methacrylate) (PMMA), as well as the phase state of blends of PMMA and poly(vinyl acetate) (PVA) has been investigated using light scattering and phase-contrast optical microscopy. The blends of LCP and PMMA have been obtained by coagulation from ternary solutions. The cloud point curves were determined. It was established that both pairs demix upon heating, ie have an LCST. In the region of intermediate composition, the phase separation proceeds according to a spinodal mechanism; however for LCP/PMMA blends, the decomposition proceeds according to a non-linear regime from the very onset. In the region of small amounts of LCP, the phase separation follows a mechanism of nucleation and growth. For PMMA/PVA blends, the spinodal decomposition proceeds according to a linear regime, in spite of the molecular mobility that PVA chains develop at lower temperatures. Only after prolonged heat treatment does the process transit to a non-linear regime. The data show a similarity between the phase behaviour of blends of liquid-crystalline and of flexible amorphous polymers. The distinction consists of the absence of a linear regime of decomposition for LCP-PMMA blends. © 1999 Society of Chemical Industry     

Rheological properties of polystyrene and poly(methyl methacrylate) blends

Rheological properties of the polystyrene (PS) and poly(methyl methacrylate) (PMMA) blends were studied by Advanced Rheometric Expansion System (ARES). Storage modulus and loss modulus of the PS and PMMA blends were measured, and the interfacial tension of the PS and PMMA blends were obtained with various emulsion models by using the storage modulus and loss modulus of the blends. The value of interfacial tension estimated from the Palierne emulsion model was found to be 2.0 mN/m. Also, the interfacial tension between PS and PMMA was calculated by a theoretical model. The values of interfacial tension of the PS and PMMA blends obtained by the experiment and theoretical model were found to be in good agreement.     

The effect of the addition of poly(styrene‐co‐glycidyl methacrylate) copolymer on the properties of polylactide/poly(methyl methacrylate) blend

The effect of the addition of poly(styrene‐co‐glycidyl methacrylate) P(S‐co‐GMA) copolymer on the properties of melt blended polylactide/poly(methyl methacrylate) (PLA/PMMA) 80/20 (wt %) composition was studied. In the literature high ductility levels were achieved by melt blending PLA with different additives. However, the gained ductility was counter balanced with drastic drops in strength and modulus values. The novelty of this work was the preparation of PLA‐based blends with polylactide content higher than 75 wt % which showed an impact resistance value improvement of about 60% compared with the neat PLA and maintained similar tensile strength and modulus values as well as glass transition temperature to neat PLA. The addition of only 3 pph of copolymer to PLA/PMMA blend improved the impact resistance almost 100%. The chemical reaction between PLA/PMMA blend and P(S‐co‐GMA) copolymer were analyzed by FTIR, rotational rheometry, and GPC/SEC. Phase structure and morphology were studied by Differential Scanning Calorimetry and Scanning Electronic Microscopy. Tensile and impact properties as well as thermal stability were also studied. Results showed that as the amount of copolymer in the blend was increased then higher was average molecular weight and polydispersity index. After the addition of P(S‐co‐GMA) copolymer to the PLA/PMMA blend the impact resistance, elongation at break and thermal stability were improved while tensile strength and elastic modulus remained almost unaltered. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43935.     

Compatibility,steady and dynamic rheological behaviors of polylactide/poly(ethylene glycol) blends

Understanding the rheological behavior of plasticized polylactide (PLA) contributed to the optimization of processing conditions and revealed the microstructure–property relationships. In this study, the morphological, thermal, steady and dynamic rheological properties of the PLA/poly(ethylene glycol) (PEG) blends were investigated by scanning electron microscope, differential scanning calorimeter, and capillary and dynamic rheometers, respectively. The results illuminated that the melt shear flow basically fitted the power law, whereas the temperature dependence of the apparent shear viscosity (η_a) or complex viscosity (η*) followed the Arrhenius equation. Both the neat PLA and PLA/PEG blends exhibited shear‐thinning behavior. Because the incorporation of PEG reduced the intermolecular forces and improved the mobility of the PLA chains, the η_a, η*, and storage and loss moduli of the PLA/PEG blends decreased. The PEG content (W_PEG) ranged from 0 to 10 wt %, both η_a and η* decreased significantly. However, the decrements of η_a and η* became unremarkable when W_PEG exceeded 10 wt %. The reason was attributed to the occurrence of phase separation, which resulted in the decrease in the plasticization and lubrication efficiencies. This study demonstrated that the addition of the right amount of PEG obviously improved the flow properties of PLA. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42919.     

Solution and solid‐state NMR investigation of poly(methyl methacrylate)/poly(vinyl pyrrolidone) blends

The development of polymer blends has become very important for the polymer industry because these blends have shown to be a successful and versatile alternative way to obtain a new polymer. In this study, binary blends formed by poly(methyl methacrylate) (PMMA) and poly(vinyl pyrrolidone) were prepared by solution casting and evaluated by solution and solid‐state NMR. Variations in the microstructure of PMMA were analyzed by ¹³C solution NMR. Solid‐state NMR promotes responses on physical interaction, homogeneity, and compatibility to use these blends to understand the behavior of the ternary blends. The NMR results led‐us to acquire information on the polymer blend microstructure and molecular dynamic behavior. From the NMR solution, it was possible to evaluate the microstructure of both polymer blend components; they were atactic. From the solid state, good compatibility between both polymer components was characterized. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 372–377, 2004     

Effects of compatibilizer on the morphological,mechanical, and rheological properties of poly(methyl methacrylate)/poly(N‐methyl methacrylimide) blends

The effects of compatibilizer on the morphological, thermal, mechanical, and rheological properties of poly(methyl methacrylate) (PMMA)/poly(N‐methyl methacrylimide) (PMMI) (70/30) blends were investigated. The compatibilizer used in this study was styrene–acrylonitrile–glycidyl methacrylate (SAN‐GMA) copolymer. Morphological characterization of the PMMA/PMMI (70/30) blend with SAN‐GMA showed a decrease in PMMI droplet size with an increase in SAN‐GMA. The glass‐transition temperature of the PMMA‐rich phase became higher when SAN‐GMA was added up to 5 parts per hundred resin by weight (phr). The flexural and tensile strengths of the PMMA/PMMI (70/30) blend increased with the addition of SAN‐GMA up to 5 phr. The complex viscosity of the PMMA/PMMI (70/30) blends increased when SAN‐GMA was added up to 5 phr, which implies an increase in compatibility between the PMMA and PMMI components. From the weighted relaxation spectrum, which was obtained from the storage modulus and loss modulus, the interfacial tension of the PMMA/PMMI (70/30) blend was calculated using the Palierne emulsion model and the Choi‐Schowalter model. The results of the morphological, thermal, mechanical, and rheological studies and the values of the interfacial tension of the PMMA/PMMI (70/30) blends suggest that the optimum compatibilizer concentration of SAN‐GMA is 5 phr. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43856.     

Preparation and thermal properties of hybrid nanocomposites of poly(methyl methacrylate)/octavinyl polyhedral oligomeric silsesquioxane blends

A series of poly(methyl methacrylate) (PMMA)/octavinyl polyhedral oligomeric silsesquioxane (POSS) blends were prepared by the solution‐blending method and characterized with Fourier transform infrared, X‐ray diffraction, transmission electron microscopy, differential scanning calorimetry, and thermogravimetric analysis techniques. The glass‐transition temperature (T_g) of the PMMA–POSS blends showed a tendency of first increasing and then decreasing with an increase in the POSS content. The maximum T_g reached 137.2°C when 0.84 mol % POSS was blended into the hybrid system, which was 28.2°C higher than that of the mother PMMA. The X‐ray diffraction patterns, transmission electron microscopy micrographs, and Fourier transform infrared spectra were employed to investigate the structure–property relationship of these hybrid nanocomposites and the T_g enhancement mechanism. The results showed that at a relatively low POSS content, POSS as an inert diluent decreased the interaction between the dipolar carbonyl groups of the homopolymer molecular chains. However, a new stronger dipole–dipole interaction between the POSS and the carbonyl of PMMA species formed at the same time, and a hindrance effect of nanosize POSS on the motion of the PMMA molecular chain may have played the main role in the T_g increase of the hybrid nanocomposites. At relatively high POSS concentrations, the strong dipole–dipole interactions that formed between the POSS and carbonyl groups of the PMMA gradually decreased because of the strong aggregation of POSS. This may be the main reason for the resultant T_g decrease in these hybrid nanocomposites. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009