Experimental heat release analysis and emissions of a HSDI diesel engine fueled with ethanol–diesel fuel blends

An experimental study is conducted to evaluate the effects of using blends of ethanol with conventional diesel fuel, with 5%, 10% and 15% (by vol.) ethanol, on the combustion and emissions of a standard, fully instrumented, four-stroke, high-speed, direct injection (HSDI), ‘Hydra’ diesel engine located at the authors’ laboratory. The tests are conducted using each of the above fuel blends or neat diesel fuel, with the engine working at a speed of 2000 rpm and at four different loads. In each test, combustion chamber and fuel injection pressure diagrams are obtained using a specially developed, high-speed, data acquisition and processing system. A heat release analysis of the experimentally obtained cylinder pressure diagrams is developed and used, with the pertinent application of the energy and state equations. From the analysis results, plots of the history in the combustion chamber of the gross heat release rate and other related parameters reveal some very interesting features, which shed light on the combustion mechanism when using these blends. Moreover, for each test, volumetric fuel consumption, exhaust smokiness and exhaust regulated gas emissions are measured. The differences in the performance and exhaust emission parameters from the baseline operation of the diesel engine, i.e., when working with neat diesel fuel, are determined and compared. The heat release analysis results for the relevant combustion mechanism, combined with the widely differing physical and chemical properties of the ethanol against those for the diesel fuel, are used to aid the correct interpretation of the observed engine behavior.     

Effect of ignition timing and hydrogen fraction on combustion and emission characteristics of natural gas direct-injection engine

An experimental study on the combustion and emission characteristics of a direct-injection spark-ignited engine fueled with natural gas/hydrogen blends under various ignition timings was conducted. The results show that ignition timing has a significant influence on engine performance, combustion and emissions. The interval between the end of fuel injection and ignition timing is a very important parameter for direct-injection natural gas engines. The turbulent flow in the combustion chamber generated by the fuel jet remains high and relative strong mixture stratification is introduced when decreasing the angle interval between the end of fuel injection and ignition timing giving fast burning rates and high thermal efficiencies. The maximum cylinder gas pressure, maximum mean gas temperature, maximum rate of pressure rise and maximum heat release rate increase with the advancing of ignition timing. However, these parameters do not vary much with hydrogen addition under specific ignition timing indicating that a small hydrogen fraction addition of less than 20% in the present experiment has little influence on combustion parameters under specific ignition timing. The exhaust HC emission decreases while the exhaust CO₂ concentration increases with the advancing of ignition timing. In the lean combustion condition, the exhaust CO does not vary much with ignition timing. At the same ignition timing, the exhaust HC decreases with hydrogen addition while the exhaust CO and CO₂ do not vary much with hydrogen addition. The exhaust NO_x increases with the advancing of ignition timing and the behavior tends to be more obvious at large ignition advance angle. The brake mean effective pressure and the effective thermal efficiency of natural gas/hydrogen mixture combustion increase compared with those of natural gas combustion when the hydrogen fraction is over 10%.     

Influence of biodiesel on engine combustion and emission characteristics

This paper discusses the influence of biodiesel on the engine combustion characteristics. The considered fuel is neat biodiesel from rapeseed oil. The considered engine is a bus diesel engine with injection M system. The engine characteristics are obtained by experiments and numerical simulation. The results obtained with biodiesel are compared to those obtained with mineral diesel under various operating regimes. In this way, the influences of biodiesel usage on the injection pressure, injection timing, ignition delay, in-cylinder gas pressure and temperature, heat release rate, exhaust gas temperatures, harmful emissions, specific fuel consumption, and on engine power are analyzed. Furthermore, the relationships among fuel properties, injection and combustion characteristics, harmful emissions, and other engine performance are determined. Special attention is given to possible explanations of higher NO_x emission in spite of lower in-cylinder gas temperature.     

Combustion of jojoba methyl ester in an indirect injection diesel engine

An experimental investigation has been carried out to examine for the first time the performance and combustion noise of an indirect injection diesel engine running with new fuel derived from pure jojoba oil, jojoba methyl ester, and its blends with gas oil. A Ricardo E6 compression swirl diesel engine was fully instrumented for the measurement of combustion pressure and its rise rate and other operating parameters. Test parameters included the percentage of jojoba methyl ester in the blend, engine speed, load, injection timing and engine compression ratio. Results showed that the new fuel derived from jojoba is generally comparable and good replacement to gas oil in diesel engine at most engine operating conditions, in terms of performance parameters and combustion noise produced.     

Experimental investigations of performance,emission and combustion characteristics of Karanja oil blends fuelled DICI engine

Vegetables oils are simplest route of biofuel utilization in direct injection compression ignition (DICI) engines however several operational and durability problems are encountered while using straight vegetable oils in CI engines due to their high viscosity and low volatility. Reduction of viscosity by blending or exhaust gas heating leads to savings in chemical processing cost incurred on transesterification. In this experimental study, performance, emission and combustion characteristics of Karanja oil blends (K10, K20, K50 and K100) with mineral diesel were investigated in unheated conditions in a direct injection CI engine at different engine loads and constant engine speed (1500 rpm) vis-à-vis baseline data from mineral diesel. Analysis of performance parameters such as brake specific fuel consumption (BSFC), thermal efficiency, and exhaust gas temperature; mass emissions of various gaseous pollutant species; combustion parameters such as in-cylinder pressure rise, instantaneous heat release and cumulative heat release etc. were carried out. Detailed combustion analysis revealed that the combustion duration increased significantly even with smaller concentration of Karanja oil in the fuel blend. HC, CO and Smoke emissions were found to decrease for 20–50% (v/v) Karanja oil content in the fuel blends.     

Application of machine learning and Box-Behnken design in optimizing engine characteristics operated with a dual-fuel mode of algal biodiesel and waste-derived biogas

Waste-derived biogas and third-generation algal biodiesel are attractive alternative fuels to substitute fossil diesel in a diesel engine. However, using biodiesel as a pilot liquid fuel and biogas as the main fuel in a diesel engine is a complicated and highly non-linear process. The current study seeks to predict and optimize the combustion and exhaust emission characteristics of a variable compression dual-fuel combustion engine. Data from experiments were obtained at a variety of engine loads, compression ratios, pilot fuel injection pressures, and timings. A multi-layer perceptron network was employed to develop an Artificial Neural Network (ANN) based prognostic model using the experimental data. The developed prognostic model was used to estimate brake thermal efficiency, biogas flow rates, peak in-cylinder pressure, carbon dioxide, unburned hydrocarbons, oxides of nitrogen, and carbon monoxide. The predictive model's robustness is demonstrated by statistical metrics such as R (0.9723–0.988) and R² (0.9453–0.9761), Nash-Sutcliffe model efficiency (94–97%), and mean absolute percentage error (0.013–0.128%), Kling-Gupta efficiency (0.9548–0.9836), and Theil's U2 model uncertainty (0.162–0.368). To optimize the parameters of dual-fuel combustion, the Multi-Output Response Surface Methodology (RSM) was employed. The trade-off assessment between emission and efficiency using the desirability approach revealed that 84% engine load, 244 bar of fuel injection pressure, 28 °BTDC of injection timing, and 17.5 compression ratio are the best-operating conditions for the test engine. An experimental investigation was used to corroborate the RSM research findings, and errors were less than 9%. It was revealed that ANN-linked RSM is a good hybrid technique for modeling, prediction, and optimization of the performance of a dual-fuel engine.     

Combustion performance and emission reduction characteristics of automotive DME engine system

This article is a condensed overview of a dimethyl ether (DME) fuel application for a compression ignition diesel engine. In this review article, the spray, atomization, combustion and exhaust emissions characteristics from a DME-fueled engine are described, as well as the fundamental fuel properties including the vapor pressure, kinematic viscosity, cetane number, and the bulk modulus. DME fuel exists as gas phase at atmospheric state and it must be pressurized to supply the liquid DME to fuel injection system. In addition, DME-fueled engine needs the modification of fuel supply and injection system because the low viscosity of DME caused the leakage. Different fuel properties such as low density, viscosity and higher vapor pressure compared to diesel fuel induced the shorter spray tip penetration, wider cone angle, and smaller droplet size than diesel fuel. The ignition of DME fuel in combustion chamber starts in advance compared to diesel or biodiesel fueled compression ignition engine due to higher cetane number than diesel and biodiesel fuels. In addition, DME combustion is soot-free since it has no carbon–carbon bonds, and has lower HC and CO emissions than that of diesel combustion. The NO_x emission from DME-fueled combustion can be reduced by the application of EGR (exhaust gas recirculation). This article also describes various technologies to reduce NO_x emission from DME-fueled engines, such as the multiple injection strategy and premixed combustion. Finally, the development trends of DME-fueled vehicle are described with various experimental results and discussion for fuel properties, spray atomization characteristics, combustion performance, and exhaust emissions characteristics of DME fuel.     

低排放单缸风冷柴油机的优化设计与匹配

以非道路单缸风冷192 F柴油机为研究对象,匹配蓄压式喷油系统,以低排放为核心目标,计算并设计了高压油泵凸轮和电控喷油器喷嘴参数,优化了螺旋进气道,重新设计了燃烧室几何形状并优化了喷油油线在燃烧室的分布,使燃烧室、进气道与蓄压式喷油系统相匹配.在标定工况、最大转矩工况下进行了喷油参数对工作过程、排放和性能影响的研究,以...     

Experimental investigations on a hydrogen diesel homogeneous charge compression ignition engine with exhaust gas recirculation

In this experimental study, hydrogen was inducted along with air and diesel was injected into the cylinder using a high pressure common rail system, in a single cylinder homogeneous charge compression ignition engine. An electronic controller was used to set the required injection timing of diesel for best thermal efficiency. The influences of hydrogen to diesel energy ratio, output of the engine and exhaust gas recirculation (EGR) on performance, emissions and combustion were studied in detail. An increase in the amount of hydrogen improved the thermal efficiency by retarding the combustion process. It also lowered the exhaust emissions. Large amounts of hydrogen and EGR were needed at high outputs for suppressing knock. The range of operation was brake mean effective pressures of 2–4 bar. The levels of HC and CO emitted were not significantly influenced by the amount of hydrogen that was used.     

Effect of ignition timing and hydrogen fraction on combustion and emission characteristics of natural gas direct-injection engine

An experimental study on the combustion and emission characteristics of a direct-injection spark-ignited engine fueled with natural gas/hydrogen blends under various ignition timings was conducted. The results show that ignition timing has a significant influence on engine performance, combustion and emissions. The interval between the end of fuel injection and ignition timing is a very important parameter for direct-injection natural gas engines. The turbulent flow in the combustion chamber generated by the fuel jet remains high and relative strong mixture stratification is introduced when decreasing the angle interval between the end of fuel injection and ignition timing giving fast burning rates and high thermal efficiencies. The maximum cylinder gas pressure, maximum mean gas temperature, maximum rate of pressure rise and maximum heat release rate increase with the advancing of ignition timing. However, these parameters do not vary much with hydrogen addition under specific ignition timing indicating that a small hydrogen fraction addition of less than 20% in the present experiment has little influence on combustion parameters under specific ignition timing. The exhaust HC emission decreases while the exhaust CO₂ concentration increases with the advancing of ignition timing. In the lean combustion condition, the exhaust CO does not vary much with ignition timing. At the same ignition timing, the exhaust HC decreases with hydrogen addition while the exhaust CO and CO₂ do not vary much with hydrogen addition. The exhaust NOx increases with the advancing of ignition timing and the behavior tends to be more obvious at large ignition advance angle. The brake mean effective pressure and the effective thermal efficiency of natural gas/hydrogen mixture combustion increase compared with those of natural gas combustion when the hydrogen fraction is over 10%. __________ Translated from Transactions of CSICE, 2006, 24(5): 394–401 [译自:内燃机学报]     

Influence of operating parameters on performance and emissions for a compression-ignition engine fueled by hydrogen/diesel mixtures

Hydrocarbon exhaust emissions are mainly recognized as a consequent of carbon-based fuel combustion in compression ignition (CI) engines. Alternative fuels can be coupled with hydrocarbon fuels to control the pollutant emissions and improve the engine performance. In this study, different parameters that influence the engine performance and emissions are illustrated with more details. This numerical work was carried out on a dual-fuel CI engine to study its performance and emission characteristics at different hydrogen energy ratios. The simulation model was run with diesel as injected fuel and hydrogen, along with air, as inducted fuel. Three-dimensional CFD software for numerical simulations was implemented to simulate the direct-injection CI engine. A reduced-reaction mechanism for n-heptane was considered in this work instead of diesel. The Hiroyasu-Nagel model was presented to examine the rate of soot formation inside the cylinder. This work investigates the effect of hydrogen variation on output efficiency, ignition delay, and emissions. More hydrogen present inside the engine cylinder led to lower soot emissions, higher thermal efficiency, and higher NO_x emissions. Ignition timing delayed as the hydrogen rate increased, due to a delay in OH radical formation. Strategies such as an exhaust gas recirculation (EGR) method and diesel injection timing were considered as well, due to their potential effects on the engine outputs. The relationship among the engine outputs and the operation conditions were also considered.     

Improving the performance of dual fuel engines running on natural gas/LPG by using pilot fuel derived from jojoba seeds

The use of jojoba methyl ester as a pilot fuel was investigated for almost the first time as a way to improve the performance of dual fuel engine running on natural gas or liquefied petroleum gas (LPG) at part load. The dual fuel engine used was Ricardo E6 variable compression diesel engine and it used either compressed natural gas (CNG) or LPG as the main fuel and jojoba methyl ester as a pilot fuel. Diesel fuel was used as a reference fuel for the dual fuel engine results. During the experimental tests, the following have been measured: engine efficiency in terms of specific fuel consumption, brake power output, combustion noise in terms of maximum pressure rise rate and maximum pressure, exhaust emissions in terms of carbon monoxide and hydrocarbons, knocking limits in terms of maximum torque at onset of knocking, and cyclic variability data of 100 engine cycles in terms of maximum pressure and its pressure rise rate average and standard deviation. The tests examined the following engine parameters: gaseous fuel type, engine speed and load, pilot fuel injection timing, pilot fuel mass and compression ratio. Results showed that using the jojoba fuel with its improved properties has improved the dual fuel engine performance, reduced the combustion noise, extended knocking limits and reduced the cyclic variability of the combustion.     

不同点火时刻下天然气掺氢缸内直喷发动机燃烧与排放特性

在缸内直喷火花点火发动机上开展了天然气掺混0％-18％氢气的混合燃料不同点火时刻下的试验研究。结果表明：对于给定的喷射时刻和喷射持续期,点火时刻对发动机性能、燃烧和排放有较大影响,喷射结束时刻与点火时刻的间隔对直喷天然气发动机极为重要,喷射结束时刻与点火时刻的间隔缩短时,混合气分层程度高,燃烧速率快,热效率高。最大放热率等燃烧特征参数随点火时刻的提前而增加。HC排放随点火时刻的提前而下降,CO2和NOx排放随点火时刻的提前而增加,NOx排放的增加在大点火提前角下更明显。掺氢可降低HC排放,对CO和CO2排放影响不大。掺氢量大于10％时可提高天然气发动机热效率。     

An experimental investigation of fuel-injection-pressure and engine-speed effects on the performance and emission characteristics of a divided-chamber diesel engine

An experimental study is conducted to investigate the fuel-injection-pressure and engine-speed effects on the performance and exhaust emissions of a naturally aspirated four-stroke indirect-injection (IDI) diesel engine with a swirl combustion chamber. The influence of the injection pressure and the engine rotational speed on fuel consumption, exhaust-gas temperature, exhaust smokiness and exhaust-gas emissions (nitrogen oxides and unburned hydrocarbons) is examined, following a detailed experimental investigation. Empirical easy-to-use correlations are produced, expressing the variation of the various parameters with injection pressure, by applying a regression analysis on the curves fitting the relevant experimental data. Theoretical aspects of diesel fuel spray progress (atomization, evaporation and mixing), combustion and emissions formation are used for the interpretation of the observed engine behaviour.     

直喷式柴油机强化燃烧的研究

本文阐述对直喷式柴油机强化燃烧的研究,重点通过所建立的优化直喷式柴油机工作过程的数学模型模拟计算,研究和分析了直喷式柴油机的工作过程和燃烧性能。计算与试验研究均表明,提高喷油压力、缩短喷油期、提高增压压力和采用预喷射快速燃烧、均质预混合燃烧等技术,均可强化柴油机燃烧过程以满足动力性、经济性和排放的要求。     

Application of response surface methodology to optimize diesel engine parameters fuelled with pongamia biodiesel/diesel blends

ABSTRACT

In the present scenario, the rate of fossil fuel consumption is very high and increasing rapidly which lead to a further increase in air pollution levels. Due to an increase in pollution level, researchers are striving to discover some cleaner and environment-friendly fuels for the diesel engines. This study was focused on the optimization of the input parameters of the diesel engine running on pongamia biodiesel for improvement in the engine performance. The input parameters selected for optimization were fuel injection pressure, fuel injection timing, pongamia biodiesel blends, and engine load with respect to BTE, BSFC, exhaust gas temperature, and P_max. An experimental analysis was performed according to the response surface methodology technique. The best engine input parameters setting for getting optimum performance was found at fuel injection timing 25 bTDC, fuel injection pressure 226 bar, 40% of pongamia biodiesel blending, at 74% of maximum rated engine load. Experimental and optimized results of the output responses at optimum input parameters were compared and found in the suggested error range.     

柴油机燃用柴油－甲醇－水复合乳化燃料的研究

本文介绍柴油机燃用柴油－甲醇－水复合乳化燃料的研究。采用自行研制的复合型乳化剂、使用机械搅拌分步乳化法和超声乳化法配制了多种配比的复合乳化燃料。通过台架试验得出了复合乳化燃料的最佳配比，分析了燃用不同配比的复合乳化燃料对柴油机的经济性、动力性、燃烧过程和排放特性的影响；使用全气缸取样系统研究了柴油机燃用不同燃料时缸内微粒生成历程。试验表明，燃用复合乳化燃料时缸内微粒生成量大幅度减少，下降值最大可达４０．７％，首次以实验手段揭示了柴油机燃用乳化燃料时烟度降低的关键原因。试验也表明，这种复合乳化燃料具有乳化剂用量少、稳定性好的特点；ＺＨ１９０Ｗ型柴油机燃用Ｄ８５Ｍ７．５Ｗ７．５复合乳化燃料时获得了满意的性能．     

Experimental investigations on the effect of fuel injection parameters on diesel engine fuelled with biodiesel blend in diesel with hydrogen enrichment

Fuel injection pressure and injection timing are two extensive injection parameters that affect engine performance, combustion, and emissions. This study aims to improve the performance, combustion, and emissions characteristics of a diesel engine by using karanja biodiesel with a flow rate of 10 L per minute (lpm) of enriched hydrogen. In addition, the research mainly focused on the use of biodiesel with hydrogen as an alternative to diesel fuel, which is in rapidly declining demand. The experiments were carried out at a constant speed of 1500 rpm on a single-cylinder, four-stroke, direct injection diesel engine. The experiments are carried out with variable fuel injection pressure of 220, 240, and 260 bar, and injection timings of 21, 23, and 25 °CA before top dead center (bTDC). Results show that karanja biodiesel with enriched hydrogen (KB20H10) increases BTE by 4% than diesel fuel at 240 bar injection pressure and 23° CA bTDC injection timing. For blend KB20H10, the emissions of UHC, CO, and smoke opacity are 33%, 16%, and 28.7% lower than for diesel. On the other hand NOx emissions, rises by 10.3%. The optimal injection parameters for blend KB20H10 were found to be 240 bar injection pressure and 23 °CA bTDC injection timing based on the significant improvement in performance, combustion, and reduction in exhaust emissions.     

船用直喷式天然气发动机喷射策略的优化

利用CONVERGE软件基于L23/30DF型船用天然气发动机建立了双天然气喷嘴、双引燃柴油喷嘴的直喷天然气发动机的缸内燃烧过程的CFD计算模型,计算了不同的柴油和天然气喷射时刻和间隔下发动机缸内燃烧和排放过程.结果 表明:引燃柴油的喷射时刻及其与天然气喷射时刻的间隔,对直喷式天然气发动机燃烧和排放性能有重要影响.当喷...     

引燃柴油对中速双燃料发动机燃烧与排放的影响

采用SAGE详细化学反应机理燃烧模型,加入液滴破裂、蒸发、碰撞以及碰壁子模型,建立了ACD320DF船用中速双燃料发动机缸内及进排气道的三维仿真模型。在气体模式下对不同引燃柴油喷射策略下的缸内燃烧特性进行数值模拟分析。分析表明:引燃柴油的喷油时刻与喷油量对发动机的燃烧及排放有重要影响。根据发动机工况合理调整微引燃柴油的喷射策略,则能得到较好的燃烧和排放性能。