Optimal sizing study of hybrid wind/PV/diesel power generation unit

In this paper, a methodology of sizing optimization of a stand-alone hybrid wind/PV/diesel energy system is presented. This approach makes use of a deterministic algorithm to suggest, among a list of commercially available system devices, the optimal number and type of units ensuring that the total cost of the system is minimized while guaranteeing the availability of the energy. The collection of 6 months of data of wind speed, solar radiation and ambient temperature recorded for every hour of the day were used. The mathematical modeling of the main elements of the hybrid wind/PV/diesel system is exposed showing the more relevant sizing variables. A deterministic algorithm is used to minimize the total cost of the system while guaranteeing the satisfaction of the load demand. A comparison between the total cost of the hybrid wind/PV/diesel energy system with batteries and the hybrid wind/PV/diesel energy system without batteries is presented.The reached results demonstrate the practical utility of the used sizing methodology and show the influence of the battery storage on the total cost of the hybrid system.     

Performance analysis of hybrid photovoltaic/diesel energy system under Malaysian conditions

Standalone diesel generating system utilized in remote areas has long been practiced in Malaysia. Due to highly fluctuating diesel price, such a system is seemed to be uneconomical, especially in the long run if the supply of electricity for rural areas solely depends on such diesel generating system. This paper would analyze the potential use of hybrid photovoltaic (PV)/diesel energy system in remote locations. National Renewable Energy Laboratory’s (NREL) HOMER software was used to perform the techno-economic feasibility of hybrid PV/diesel energy system. The investigation demonstrated the impact of PV penetration and battery storage on energy production, cost of energy and number of operational hours of diesel generators for the given hybrid configurations. Emphasis has also been placed on percentage fuel savings and reduction in carbon emissions of different hybrid systems. At the end of this paper, suitability of utilizing hybrid PV/diesel energy system over standalone diesel system would be discussed mainly based on different solar irradiances and diesel prices.     

DESIGN OF HYBRID-PHOTOVOLTAIC POWER GENERATOR, WITH OPTIMIZATION OF ENERGY MANAGEMENT

A methodology is developed for calculating the correct size of a photovoltaic (PV)-hybrid system and for optimizing its management. The power for the hybrid system comes from PV panels and an engine-generator – that is, a gasoline or diesel engine driving an electrical generator. The combined system is a stand-alone or autonomous system, in the sense that no third energy source is brought in to meet the load. Two parameters were used to characterize the role of the engine-generator: denoted SDM and SAR, they are, respectively, the battery charge threshold at which it is started up, and the storage capacity threshold at which it is stopped, both expressed as a percentage of the nominal battery storage capacity. The methodology developed is applied to designing a PV-hybrid system operating in Corsica, as a case study. Various sizing configurations were simulated, and the optimal configuration that meets the autonomy constraint (no loss of load) was determined, by minimizing of the energy cost. The influence of the battery storage capacity on the solar contribution is also studied. The smallest energy cost per kWh was obtained for a system characterized by an SDM=30% and an SAR=70%. A study on the effects of component lifetimes on the economics of PV-hybrid and PV stand-alone systems has shown that battery size can be reduced by a factor of two in PV-hybrid systems, as compared to PV stand-alone systems.     

Impact of battery storage on economics of hybrid wind‐diesel power systems in commercial applications in hot regions

Integration of wind machines and battery storage with the diesel plants is pursued widely to reduce dependence on fossil fuels. The aim of this study is to assess the impact of battery storage on the economics of hybrid wind‐diesel power systems in commercial applications by analyzing wind‐speed data of Dhahran, East‐Coast, Kingdom of Saudi Arabia (K.S.A.). The annual load of a typical commercial building is 620,000 kWh. The monthly average wind speeds range from 3.3 to 5.6 m/s. The hybrid systems simulated consist of different combinations of 100‐kW commercial wind machines (CWMs) supplemented with battery storage and diesel generators. National Renewable Energy Laboratory's (NREL's) (HOMER Energy's) Hybrid Optimization Model for Electric Renewables (HOMER) software has been employed to perform the economic analysis. The simulation results indicate that for a hybrid system comprising of 100‐kW wind capacity together with 175‐kW diesel system and a battery storage of 4 h of autonomy (i.e. 4 h of average load), the wind penetration (at 37‐m hub height, with 0% annual capacity shortage) is 25%. The cost of generating energy (COE, $/kWh) from this hybrid wind–battery–diesel system has been found to be 0.139 $/kWh (assuming diesel fuel price of 0.1$/L). The investigation examines the effect of wind/battery penetration on: COE, operational hours of diesel gensets. Emphasis has also been placed on un‐met load, excess electricity, fuel savings and reduction in carbon emissions (for wind–diesel without battery storage, wind–diesel with storage, as compared to diesel‐only situation), cost of wind–battery–diesel systems, COE of different hybrid systems, etc. The study addresses benefits of incorporation of short‐term battery storage (in wind–diesel systems) in terms of fuel savings, diesel operation time, carbon emissions, and excess energy. The percentage fuel savings by using above hybrid system is 27% as compared to diesel‐only situation Copyright © 2012 John Wiley & Sons, Ltd.     

Performance analysis of various hybrid renewable energy systems using battery,hydrogen, and pumped hydro‐based storage units

The aim of this research is to analyze the techno‐economic performance of hybrid renewable energy system (HRES) using batteries, pumped hydro‐based, and hydrogen‐based storage units at Sharurah, Saudi Arabia. The simulations and optimization process are carried out for nine HRES scenarios to determine the optimum sizes of components for each scenario. The optimal sizing of components for each HRES scenario is determined based on the net present cost (NPC) optimization criterion. All of the nine optimized HRES scenarios are then evaluated based on NPC, levelized cost of energy, payback period, CO₂ emissions, excess electricity, and renewable energy fraction. The simulation results show that the photovoltaic (PV)‐diesel‐battery scenario is economically the most viable system with the NPC of US$2.70 million and levelized cost of energy of US$0.178/kWh. Conversely, PV‐diesel‐fuel cell system is proved to be economically the least feasible system. Moreover, the wind‐diesel‐fuel cell is the most economical scenario in the hydrogen‐based storage category. PV‐wind‐diesel‐pumped hydro scenario has the highest renewable energy fraction of 89.8%. PV‐wind‐diesel‐pumped hydro scenario is the most environment‐friendly system, with an 89% reduction in CO₂ emissions compared with the base‐case diesel only scenario. Overall, the systems with battery and pumped hydro storage options have shown better techno‐economic performance compared with the systems with hydrogen‐based storage.     

Minimization of green house gases emission by using hybrid energy system for telephony base station site application

Cellular mobile service is a rapidly expanding and a very competitive business worldwide, including developing countries. This paper proposes that the suitable alternative solution of grid power is the stand-alone PV/wind hybrid energy system with diesel generator as a backup for cellular mobile telephony base station site in isolated areas. It is expected that the newly developed and installed system would provide very good opportunities for mobile telephony base station in near future. In addition, protecting the environment and combating climate change are two of the most pressing challenges facing humankind. As energy prices soar, network operators are increasingly scrutinizing their environmental and social responsibilities. This system will be more cost effective and environmental friendly over the conventional diesel generator. Approximately 70–80% fuel cost over conventional diesel generator and the emission of CO₂ and other harmful gasses in environments were reduced.     

Technical and economic assessment of grid-independent hybrid photovoltaic–diesel–battery power systems for commercial loads in desert environments

Solar photovoltaic (PV) hybrid system technology is a hot topic for R&D since it promises lot of challenges and opportunities for developed and developing countries. The Kingdom of Saudi Arabia (KSA) being endowed with fairly high degree of solar radiation is a potential candidate for deployment of PV systems for power generation. Literature indicates that commercial/residential buildings in KSA consume an estimated 10–45% of the total electric energy generated. In the present study, solar radiation data of Dhahran (East-Coast, KSA) have been analyzed to assess the techno-economic viability of utilizing hybrid PV–diesel–battery power systems to meet the load requirements of a typical commercial building (with annual electrical energy demand of 620,000 kW h). The monthly average daily solar global radiation ranges from 3.61 to 7.96 kW h/m². NREL's HOMER software has been used to carry out the techno-economic viability. The simulation results indicate that for a hybrid system comprising of 80 kWp PV system together with 175 kW diesel system and a battery storage of 3 h of autonomy (equivalent to 3 h of average load), the PV penetration is 26%. The cost of generating energy (COE, US$/kW h) from the above hybrid system has been found to be 0.149 $/kW h (assuming diesel fuel price of 0.1 $/L). The study exhibits that for a given hybrid configuration, the operational hours of diesel generators decrease with increase in PV capacity. The investigation also examines the effect of PV/battery penetration on COE, operational hours of diesel gensets for a given hybrid system. Emphasis has also been placed on unmet load, excess electricity generation, percentage fuel savings and reduction in carbon emissions (for different scenarios such as PV–diesel without storage, PV–diesel with storage, as compared to diesel-only situation), cost of PV–diesel–battery systems, COE of different hybrid systems, etc.     

Hybrid (solar and wind) energy system for Al Hallaniyat Island electrification

Wind–PV–diesel hybrid power generation system technology is a promising energy option since it provides opportunities for developed and developing countries to harness naturally available, inexhaustible and pollution-less resources. The aim of this study is to assess the techno-economic feasibility of utilizing a hybrid wind–PV–diesel power system to meet the load of Al Hallaniyat Island. Hybrid Optimization Model for Electric Renewables software has been employed to carry out the present study. The simulation results indicate that the cost of generating energy (COE) is $0.222 kWh^?1 for a hybrid system composed of a 70 kW PV system, 60 kW wind turbine and batteries together with a 324.8 kW diesel system. Moreover, using the same system but without batteries will increase the COE to $0.225 kWh^?1, the fuel consumption, the excess energy and the total operating hours for the diesel generators. The PV–wind hybrid option is techno-economically viable for rural electrification.     

Experimental study of electricity generation by Solar PV/diesel hybrid systems without battery storage for off-grid areas

This paper presents the results of an experimental study of a PV/diesel hybrid system without storage. Experimental results show that the sizing of a PV/diesel hybrid system by taking into account the solar radiation and the load/demand profile of a typical area may lead the diesel generator to operate near its optimal point (70–80% of its nominal power). The present paper shows that for a reliability of a PV/diesel hybrid system, the rated power of the diesel generator should be equal to the peak load. By the way, it has been verified through this study that the functioning of a PV/diesel hybrid system is efficient for higher load and higher solar radiation.     

超级电容器蓄电池混合储能独立光伏系统研究

建立了混合储能系统的数学模型,对系统性能的提升进行了定量分析。提出了一种无源式并联储能方案,并应用于独立光伏系统中,仿真和实验结果表明,在光伏系统的发电功率和负载功率脉动的情况下,蓄电池的充放电电流比较平滑。合理配置超级电容器组的容量,可以减少由于日照量变化所导致的蓄电池充放电小循环次数。对解决光伏等可再生能源系统中蓄电池储能的问题,具有现实意义。     

Optimal energy management system for stand-alone wind turbine/photovoltaic/hydrogen/battery hybrid system with supervisory control based on fuzzy logic

This paper presents a novel hourly energy management system (EMS) for a stand-alone hybrid renewable energy system (HRES). The HRES is composed of a wind turbine (WT) and photovoltaic (PV) solar panels as primary energy sources, and two energy storage systems (ESS), which are a hydrogen subsystem and a battery. The WT and PV panels are made to work at maximum power point, whereas the battery and the hydrogen subsystem, which is composed of fuel cell (FC), electrolyzer and hydrogen storage tank, act as support and storage system. The EMS uses a fuzzy logic control to satisfy the energy demanded by the load and maintain the state-of-charge (SOC) of the battery and the hydrogen tank level between certain target margins, while trying to optimize the utilization cost and lifetime of the ESS. Commercial available components and an expected life of the HRES of 25 years were considered in this study. Simulation results show that the proposed control meets the objectives established for the EMS of the HRES, and achieves a total cost saving of 13% over other simpler EMS based on control states presented in this paper.     

Techno-economic evaluation of off-grid hybrid photovoltaic–diesel–battery power systems for rural electrification in Saudi Arabia—A way forward for sustainable development

The burning of depleting fossil fuels for power generation has detrimental impact on human life and climate. In view of this, renewable solar energy sources are being increasingly exploited to meet the energy needs. Moreover, solar photovoltaic (PV)–diesel hybrid system technology promises lot of opportunities in remote areas which are far from utility grid and are driven by diesel generators. Integration of PV systems with the diesel plants is being disseminated worldwide to reduce diesel fuel consumption and to minimize atmospheric pollution. The Kingdom of Saudi Arabia (K.S.A.) being endowed with high intensity of solar radiation, is a prospective candidate for deployment of PV systems. Also, K.S.A. has large number of remote scattered villages. The aim of this study is to analyze solar radiation data of Rafha, K.S.A., to assess the techno-economic feasibility of hybrid PV–diesel–battery power systems to meet the load requirements of a typical remote village Rawdhat Bin Habbas (RBH) with annual electrical energy demand of 15,943 MWh. Rafha is located near RBH. The monthly average daily global solar radiation ranges from 3.04 to 7.3 kWh/m². NREL's HOMER software has been used to perform the techno-economic evaluation. The simulation results indicate that for a hybrid system composed of 2.5 MWp capacity PV system together with 4.5 MW diesel system (three 1.5 MW units) and a battery storage of 1 h of autonomy (equivalent to 1 h of average load), the PV penetration is 27%. The cost of generating energy (COE, US$/kWh) from the above hybrid system has been found to be 0.170$/kWh (assuming diesel fuel price of 0.1$/l). The study exhibits that the operational hours of diesel generators decrease with increase in PV capacity. The investigation also examines the effect of PV/battery penetration on COE, operational hours of diesel gensets. Concurrently, emphasis has been placed on: un-met load, excess electricity generation, percentage fuel savings and reduction in carbon emissions (for different scenarios such as: PV–diesel without storage, PV–diesel with storage, as compared to diesel-only situation), COE of different hybrid systems, etc. The decrease in carbon emissions by using the above hybrid system is about 24% as compared to the diesel-only scenario.     

Dynamic modeling and sizing optimization of stand-alone photovoltaic power systems using hybrid energy storage technology

Economic and environmental concerns over fossil fuels encourage the development of photovoltaic (PV) energy systems. Due to the intermittent nature of solar energy, energy storage is needed in a stand-alone PV system for the purpose of ensuring continuous power flow. Three stand-alone photovoltaic power systems using different energy storage technologies are studied in this paper. Key components including PV modules, fuel cells, electrolyzers, compressors, hydrogen tanks and batteries are modeled in a clear way so as to facilitate the evaluation of the power systems. Based on energy storage technology, a method of ascertaining minimal system configuration is designed to perform the sizing optimization and reveal the correlations between the system cost and the system efficiency. The three hybrid power systems, i.e., photovoltaic/battery (PV/Battery) system, photovoltaic/fuel cell (PV/FC) system, and photovoltaic/fuel cell/battery (PV/FC/Battery) system, are optimized, analyzed and compared. The obtained results indicate that maximizing the system efficiency while minimizing system cost is a multi-objective optimization problem. As a trade-off solution to the problem, the proposed PV/FC/Battery hybrid system is found to be the configuration with lower cost, higher efficiency and less PV modules as compared with either single storage system.     

Generation unit sizing and cost analysis for stand-alone wind,photovoltaic, and hybrid wind/PV systems

This paper presents the results of investigations on the application of wind, photovoltaic (PV), and hybrid wind/PV power generating systems for utilization as stand-alone systems. A simple numerical algorithm has been developed for generation unit sizing. It has been used to determine the optimum generation capacity and storage needed for a stand-alone, wind, PV, and hybrid wind/PV system for an experimental site in a remote area in Montana with a typical residential load. Generation and storage units for each system are properly sized in order to meet the annual load and minimize the total annual cost to the customer. In addition, an economic analysis has been performed for the above three scenarios and is used to justify the use of renewable energy versus constructing a line extension from the nearest existing power line to supply the load with conventional power. Annual average hourly values for load, wind speed, and insolation have been used     

Optimal design and techno-economic analysis of a hybrid solar–wind power generation system

Solar energy and wind energy are the two most viable renewable energy resources in the world. Good compensation characters are usually found between solar energy and wind energy. This paper recommend an optimal design model for designing hybrid solar–wind systems employing battery banks for calculating the system optimum configurations and ensuring that the annualized cost of the systems is minimized while satisfying the custom required loss of power supply probability (LPSP). The five decision variables included in the optimization process are the PV module number, PV module slope angle, wind turbine number, wind turbine installation height and battery capacity. The proposed method has been applied to design a hybrid system to supply power for a telecommunication relay station along south-east coast of China. The research and project monitoring results of the hybrid project were reported, good complementary characteristics between the solar and wind energy were found, and the hybrid system turned out to be able to perform very well as expected throughout the year with the battery over-discharge situations seldom occurred.     

Sizing of a stand-alone hybrid wind-photovoltaic system using a three-event probability density approximation

The PV-array and battery storage sizing of a stand-alone hybrid wind-photovoltaic system is being addressed here. A probabilistic approach is used to arrive at the results. A new technique using a three event probability density instead of the traditional two event approximation is developed. This technique is then used to determine the optimum relationship between the number of PV panels and the number of storage batteries required for the stand-alone hybrid wind-photovoltaic system, to meet a certain loss of power probability. This method uses long term data of wind speed, irradiance and ambient temperature taken every hour for 30 yr and the load specifications for a “typical New England house” that is going to be powered by the hybrid system.     

Pre-feasibility study of stand-alone hybrid energy systems for applications in Newfoundland

A potential solution for stand-alone power generation is to use a hybrid energy system in parallel with some hydrogen energy storage. In this paper, a pre-feasibility study of using hybrid energy systems with hydrogen as an energy carrier for applications in Newfoundland, Canada is explained. Various renewable and non-renewable energy sources, energy storage methods and their applicability in terms of cost and performance are discussed. HOMER is used as a sizing and optimization tool. Sensitivity analysis with wind speed data, solar radiation level, diesel price and fuel cell cost was done. A remote house having an energy consumption of 25 kW h/d with a 4.73 kW peak power demand was considered as the stand-alone load. It was found that, a wind–diesel–battery hybrid system is the most suitable solution at present. However, with a reduction of fuel cell cost to 15% of its current value, a wind–fuel cell system would become a superior choice. Validity of such projection and economics against conventional power sources were identified. Sizing, performance and various cost indices were also analyzed in this paper.     

Economic analysis of PV/diesel hybrid system with flywheel energy storage

This paper analyzes a hybrid energy system performance with photovoltaic (PV) and diesel systems as the energy sources. The hybrid energy system is equipped with flywheel to store excess energy from the PV. HOMER software was employed to study the economic and environmental benefits of the system with flywheels energy storage for Makkah, Saudi Arabia. The analysis focused on the impact of utilizing flywheel on power generation, energy cost, and net present cost for certain configurations of hybrid system. Analyses on fuel consumption and carbon emission reductions for the system configurations were also presented in this paper.     

Optimal sizing of battery storage for hybrid (wind+diesel) power systems

Hourly mean wind-speed data for the period 1986–1997 [except the years 1989 (some data is missing) and 1991 (Gulf War)] recorded at the solar radiation and meteorological monitoring station, Dhahran (26°C 32′ N, 50° 13′ E), Saudi Arabia, have been analyzed to investigate the optimum size of battery storage capacity for hybrid (wind+diesel) energy conversion systems at Dhahran. The monthly average wind speeds for Dhahran range from 4.12 to 6.42 m/s. As a case study, the hybrid system considered in the present analysis consists of two 10 kW Wind Energy Conversion Systems (WECS), together with a battery storage system and a diesel back-up. The yearly and monthly average energy generated from the above hybrid system have been presented. More importantly, the study explores the impact of variation of battery storage capacity on hybrid power generation. The results exhibit a trade-off between size of the storage capacity and diesel power to be generated to cope with specific annual load distribution [41,500], and for given energy generation from WECS. The energy to be generated from the back-up diesel generator and the number of operational hours of the diesel system to meet a specific annual electrical energy demand have also been presented. The diesel back-up system is operated at times when the power generated from WECS fails to satisfy the load and when the battery storage is depleted. The present study shows that for economic considerations, for optimum use of battery storage and for optimum operation of diesel system, storage capacity equivalent to one to three days of maximum monthly average daily demand needs to be used. It has been found that the diesel energy to be generated without any storage is considerably high; however, use of one day of battery storage reduces diesel energy generation by about 35%; also the number of hours of operation of the diesel system are reduced by about 52%.     

Performance comparison investigation on solar photovoltaic-thermoelectric generation and solar photovoltaic-thermoelectric cooling hybrid systems under different conditions

The performance of solar photovoltaic-thermoelectric generation hybrid system (PV-TGS) and solar photovoltaic-thermoelectric cooling hybrid system (PV-TCS) under different conditions were theoretically analysed and compared. To test the practicality of these two hybrid systems, the performance of stand-alone PV system was also studied. The results show that PV-TGS and PV-TCS in most cases will result in the system with a better performance than stand-alone PV system. The advantage of PV-TGS is emphasised in total output power and conversion efficiency which is even poorer in PV-TCS than that in stand-alone PV system at the ambient wind speed u_w being below 3 m/s. However, PV-TCS has obvious advantage on lowering the temperature of PV cell. There is an obvious increase in tendency on the performance of PV-TGS and PV-TCS when the cooling capacity of two hybrid systems varies from around 0.06 to 0.3?W/K. And it is also proved that not just a-Si in PV-TGS can produce a better performance than the stand-alone PV system alone at most cases.