Low-temperature conducting performance of transparent indium tin oxide/antimony tin oxide electrodes

We fabricated transparent indium tin oxide (ITO)/antimony tin oxide (ATO) electrodes using a combined process of spin-coating of hybrid ITO nanoinks, electrospraying of ATO, and hydrogen (H₂) activation carried out at a low annealing temperature of 200 °C. The produced ITO electrode exhibited an enhanced surface densification and phase conversion of In(OH)₃ to ITO. As a result, the H₂-activated ITO/ATO electrodes exhibited excellent transparent conducting performances with a superior sheet resistance of ~47.5 Ω/□ and a good transmittance of ~85.3% as compared to the ITO and ITO/ATO electrodes. Despite the use of the low annealing temperature, the achieved improvement in the conducting performance could be attributed to the synergistic effect of the enhanced carrier concentration and the Hall mobility related to the improved surface densification achieved with the electrosprayed ATO thin film and reduction of the residual In(OH)₃ phase by H₂ activation. Therefore, our method can be used as a novel strategy for obtaining high-performance solution-processed transparent conducting oxides at a low annealing temperature of 200 °C for use in various optoelectronic applications.     

Hydrogen reduced graphene oxide/metal grid hybrid film: towards high performance transparent conductive electrode for flexible electrochromic devices

The metal grid and reduced graphene oxide (RGO) are both promising transparent conductive materials for replacing the indium tin oxide (ITO) in flexible optoelectronics. However, the large empty area that exists in the grid together with the relatively high sheet resistance of RGO hinder both the materials for practical applications. In this work, we report for the first time a novel strategy for efficient combination of the metal grid and RGO by using a newly developed room-temperature reduction technique. The obtained RGO/metal grid hybrid films not only overcome the shortcomings of individual components but exhibit enhanced optical and electrical performances (R_s = 18 Ω sq⁻¹ and T = 80%) and excellent flexural endurance. With this hybrid film as the window electrode, a highly flexible electrochromic device with excellent stability and ultra-fast response shorter than 60 ms has been successfully fabricated. Considering its high efficiency, high quality, low cost and large area, the strategy would be particularly useful for economically fabricating various metal grid/RGO films which are quite promising high performance transparent and conductive materials for next generation optoelectronic devices.     

Synthesis and light emitting properties of sulfide-containing polyfluorenes and their nanocomposites with CdSe nanocrystals: A simple process to suppress keto-defect

A new series of sulfide-containing polyfluorene homopolymers and copolymers (PFS, PF1, PF3 and PF4) comprising 9,9-di[11-(decylsulfanyl)undecyl] fluorene, 9,9-dihexylfluorene, triphenylamine or benzothiadiazole moieties were synthesized by Ni(0)-mediated Yamamoto-coupling and palladium-catalyzed Suzuki polymerizations. Three other polyfluorenes (PF2, PF5 and PFC6) without sulfur atom in the alkyl side chains were also synthesized by a similar method for comparison purpose. These fluorene-based polymers were characterized using FT-IR spectroscopy, elemental analysis, DSC, TGA, photoluminescence (PL) and electroluminescence (EL) spectroscopies. The synthesized polymers PFS and PF1–PF3 emit blue light at around 440–468 nm, while copolymers PF4 and PF5 emit green light at around 540 nm. In annealing experiments, these polymer films show better stability against thermal oxidation than polymer PFC6. Sulfide-containing polymers show not only good electroluminescent color stability, but their EL spectra also remain unchanged at high driving voltage. A multi-layer electroluminescent device with the configuration of ITO/PEDOT/PF1/CsF/Al exhibited a stable sky-blue emission with color coordinates (0.21, 0.23) at 10 V, which showed a maximum brightness of 2991 cd/m² at 8 V (75 mA/cm²) and a maximum efficiency of 1.36 cd/A. Finally, by ligand exchange process, the sulfur element could form coordination bonding with quantum dots, and PLED devices using these new QDs-containing organic/inorganic hybrid materials as light-emitting layers exhibit superior or comparable EL performance compared to those without quantum dots.     

Synthesis and characterization of a novel electroluminescent polymer based on phenoxazine and fluorene derivatives

A new electroluminescent polymer was prepared by oxidative coupling copolymerization of N-(4-n-butylphenyl)phenoxazine (PPX) and 9,9-di-n-butylfluorene (DBF) using iron(III) chloride. The obtained polymers were soluble in common organic solvents and had number-average molecular weight as high as 10,000. The UV–vis absorption maximum and photoluminescence peak shifted to longer wavelengths with the increase of PPX content. The increase of PPX content also caused increase of hole mobility and decrease of electron mobility. A simple single-layer light-emitting-diode device having a structure of indium tin oxide/polymer/Ca/Al was fabricated. The polymer containing 30% of PPX unit showed highest electroluminescent properties with a maximum luminance of 1084 cd/m² at 15.5 V operating voltage.     

Hyperbranched triazine-containing polyfluorenes: Efficient blue emitters for polymer light-emitting diodes (PLEDs)

A series of hyperbranched triazine-containing polyfluorenes were synthesized by an “A₂ + A′₂ + B₃” approach based on Suzuki polycodensation. The polymers showed pure blue emission and the maximum emissions red-shifted in polar solvents and in solid film. By introducing triazine into polyfluorene, the electron injection and transport properties were improved and green emission was suppressed. PLED devices fabricated with the polymers showed reasonably high external quantum efficiencies.     

Photovoltaic property dependence of dye-sensitized solar cells on sheet resistance of FTO substrate deposited via spray pyrolysis

F-doped SnO₂ (FTO) glass substrate was successfully fabricated via spray-pyrolysis deposition for use as a transparent conducting substrate in dye-sensitized solar cells (DSSCs). To investigate the performance dependence of DSSCs on the sheet resistance of the FTO films, three types of FTO films with sheet resistance values of 2 Ω/□, 4 Ω/□, and 10 Ω/□ were fabricated. Commercial FTO films having a sheet resistance of 15 Ω/□ were prepared for comparison. The structural, electrical, and optical properties of FTO films were characterized by scanning electron microscopy (SEM), atomic force microscopy (AFM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), the four-point probe method, and UV–vis spectrometry. The photocurrent–voltage data show that DSSCs fabricated with a sheet resistance of 2 Ω/□ exhibit the best photoconversion effciency (～5.5%) among the four samples. The performance improvement of DSSCs is due to improved short-circuit current density (～13.7 mA/cm²) and fill factor (～62.3%).     

A high-performance asymmetric supercapacitor based on carbon and carbon–MnO2 nanofiber electrodes

An asymmetric supercapacitor with high energy and power densities has been fabricated using MnO₂/carbon nanofiber composites as positive electrode and activated carbon nanofibers as negative electrode in Na₂SO₄ aqueous electrolyte. Both electrode materials are freestanding in nature without any conductive additives or binders and exhibit outstanding electrochemical performances. The as-assembled asymmetric supercapacitor with optimal mass ratio can be operated reversibly over a wide voltage range of 0–2.0 V, and presents a maximum energy density of 30.6 Wh kg⁻¹, which is much higher than those of symmetric supercapacitors. Moreover, the supercapacitor exhibits excellent rate capability (high power density of 20.8 kW kg⁻¹ at 8.7 Wh kg⁻¹) and long-term cycling stability with only 6% loss of its initial capacitance after 5000 cycles. These attractive results make these freestanding materials promising for applications in aqueous electrolyte-based asymmetric supercapacitors with high energy and power densities delivery.     

The composite material based on Dawson-type polyoxometalate and activated carbon as the supercapacitor electrode

A supercapacitor electrode assembled from activated carbon (AC) and (NH₄)₆[P₂Mo₁₈O₆₂]·14.2H₂O (P₂Mo₁₈) was fabricated for the first time, and showed remarkable electrochemical performance ascribed to the synergy of the double layer capacitance of AC and the pseudocapacitance of P₂Mo₁₈. The investigations indicate that the AC/P₂Mo₁₈ electrode exhibits a specific capacitance of 275 F g^− 1 at a high current density of 6 A g^− 1, which is substantially larger than the 182 F g^− 1 of the AC electrode. In addition, the AC/P₂Mo₁₈ electrode possesses a remarkable rate capability (89%) when the current density is increased from 2 to 6 A g^− 1.     

La0.6Sr0.4Co0.2Fe0.8O3-δ oxygen electrodes for solid oxide cells prepared by polymer precursor and nitrates solution infiltration into gadolinium doped ceria backbone

Infiltration is a method, which can be applied for the electrode preparation. In this paper oxygen electrode is prepared solely by the infiltration of La_0.6Sr_0.4Co_0.2Fe_0.8O_3‐δ (LSCF) into Ce_0.8Gd_0.2O_2-δ (CGO) backbone. The use a polymer precursor as an infiltrating medium, instead of an aqueous nitrate salts solution is presented. It is shown that the polymer forms the single-phase perovskite at 600 °C, contrary to the nitrates solution. As a result, obtained area specific resistance (ASR) is lowered from 0.21 Ω cm² to 0.16 Ω cm² at 600 °C. More than 35% of LSCF in the oxygen electrode decreases the performance.     

Synthesis of reduced graphene oxide/tungsten trioxide nanocomposite electrode for high electrochemical performance

A facile and well-controllable reduced graphene oxide/tungsten trioxide (rGO/WO₃) nanocomposite electrode was successfully synthesized via an electrostatic assembly route at 350 rpm for 24 h. In this study, hexagonal-phase WO₃ (h-WO₃) nanofiber was well distributed on rGO sheets by applying optimal processing parameters. The as-synthesized rGO/WO₃ nanocomposite electrode was compared with pure h-WO₃ electrode. A maximum specific capacitance of 85.7 F g⁻¹ at a current density of 0.7 A g⁻¹ was obtained for the rGO/WO₃ nanocomposite electrode, which showed better electrochemical performance than the WO₃ electrode. The incorporation of WO₃ into rGO could prevent the restacking of rGO and provide favourable surface adsorption sites for intercalation/de-intercalation reactions. The impedance studies demonstrated that the rGO/WO₃ nanocomposite electrode exhibited lower resistance because of the superior conductivity of rGO that improved ion diffusion into the electrode. To evaluate the contribution of WO₃ to the rGO/WO₃ nanocomposite, the influence of mass loading of WO₃ on the capacitance was investigated.     

Logotype-selective electrochromic glass display

This paper describes a fabrication method of a logotype-selective electrochromic (EC) glass. The EC glass performance based on the sample size, WO₃ film thickness, and internal impedances under various applied voltages are also discussed. The logotype-selective electrochromic glass was fabricated by the sputter deposition process. Both working and counter electrode were coated with ITO/WO₃ films. The specific logotypes of “NCUT” and “NUU” can be displayed with positive and negative voltages applied to the EC glass. EC glasses of various sizes (1 cm², 4 cm², 9 cm², 25 cm², and 100 cm²) were also fabricated by sputter deposition process. When voltage (?3.5 V) was applied to the device, the active layer of the assembled device changed from almost transparent to a translucent blue color (colored). The average transmittance in the visible region of the spectrum for a 100 cm² EC device was 73% in the bleached state. The best device, with a 140 nm WO₃ active layer, had average transmittances in the colored and bleached states of 11.9% and 54.8%, respectively. Cyclic voltammogram tests showed that reproducibility of the colored/bleached cycles was good. Nyquist plots showed that increasing the device size decreased the current density, and the electrolyte impedance increased because of a low conductive electrolyte in the device.     

Functionalized three-dimensional graphene networks for high performance supercapacitors

Three-dimensional (3D) thermal reduced graphene network (TRGN) deposition on Ni foam without any conductive agents and polymer binders was successfully synthesized by dipping Ni foam into graphene oxide (GO) suspension and subsequent thermal reduction process. The direct and close contact between thermal reduced graphene and Ni foam is beneficial to the enhanced conductivity of the electrode, as well as the improvement of ion diffusion/transport into the electrode. Additionally, low-temperature reduction of GO possesses a large amount of stable oxygen-containing groups that can provide high pseudocapacitance. As a result, the TRGN electrode delivers a high specific capacitance of 442.8 F g⁻¹ at 2 mV s⁻¹ in 6 mol L⁻¹ KOH. Moreover, symmetric supercapacitor based on TRGN exhibits a maximum energy density of 30.4 Wh kg⁻¹ based on the total mass of the two electrodes in 1 mol L⁻¹ Na₂SO₄ electrolyte, as well as excellent cycling stability with 118% of its initial capacitance after 5000 cycles.     

Fabrication and properties of transparent Tb:YAG fluorescent ceramics with different doping concentrations

Terbium doped yttrium aluminum garnet (Tb:YAG) transparent ceramics with different doping concentrations were fabricated by the solid-state reaction method using commercial Y₂O₃, α-Al₂O₃ and Tb₄O₇ powders as raw materials. Samples sintered at 1750 °C for 20 h were utilized to observe the optical transmittance, microstructure and fluorescence characteristics. It is found that all the Tb: YAG ceramics with different doping concentrations exhibit homogeneous structures with grain size distributions around 22–29 µm. For the 5 at% Tb:YAG transparent ceramics, the grain boundaries are clean with no secondary phases. The photoluminescence spectra show that Tb:YAG ceramics emit predominantly at 544 nm originated from the energy levels transition of ⁵D₄→⁷F₅ of Tb³⁺ ions, and the intensity of the emission peak reaches a maximum value when the Tb³⁺ concentration is 5 at%. The in-line transmittance of the 5 at% Tb:YAG ceramics is 73.4% at the wavelength of 544 nm, which needs to be further enhanced by optimizing the fabrication process. We think that Tb:YAG transparent ceramics may have potential applications in the high-power white LEDs.     

Electrochromic performance and ion sensitivity of a terthienyl based fluorescent polymer

A novel terthienyl based fluorescent polymer bearing strong electron-withdrawing substituents directly attached to the 3,4-positions of the central thiophene ring was synthesized by electrochemical polymerization of diethyl 2,5-di(3,4-ethylenedioxythiophen-2-yl)thiophene-3,4-dicarboxylate. The corresponding polymer was characterized by cyclic voltammetry, FT-IR and UV–vis spectroscopy. The polymer has a well-defined redox process (E_p,1/2 = 0.74 V) and demonstrates a reversible electrochromic behavior; lilac in the neutral state and transparent sky blue in the oxidized state. Also, the polymer had low band gap (E_g = 1.82 eV) and high redox stability (retaining 94.0% of its electro-activity after 500th switch). Moreover, the sensitivity of both the monomer and its polymer towards metal cations was investigated by monitoring the change in the fluorescence intensity. Among various common ions both the monomer and its polymer were found to be selective towards Cu²⁺ and Cu⁺ ions by quenching the fluorescence efficiency with a Stern–Volmer constant (K_sv) of (1.4–1.6 × 10³ M^?1) and (1.5–1.8 × 10² M^?1) for monomer and polymer solutions, respectively.     

Effects of porous C/C density on the densification behavior and ablation property of C/C–ZrC–SiC composites

C/C–ZrC–SiC composites were prepared by precursor infiltration and pyrolysis process using a mixture solution of organic zirconium-containing polymer and polycarbosilane as precursors. Porous carbon/carbon (C/C) composites with density of 0.92, 1.21 and 1.40 g/cm³ were used as preforms, and the effects of porous C/C density on the densification behavior and ablation resistance of C/C–ZrC–SiC composites were investigated. The results show that the C/C preforms with a lower density have a faster weight gain, and the obtained C/C–ZrC–SiC composites own higher bulk density and open porosity. The composites fabricated from the C/C preforms with a density of 1.21 g/cm³ exhibit better ablation resistance with a surface temperature of over 2400 °C during ablation. After ablation for 120 s, the linear and mass ablation rates of the composites are as low as 1.02 × 10⁻³ mm/s and −4.01 × 10⁻⁴ g/s, respectively, and the formation of a dense and continuous coating of molten ZrO₂ solid solution is the reason for their great ablation resistance.     

Fabrication of highly efficient TiO2/Ag/TiO2 multilayer transparent conducting electrode with N ion implantation for optoelectronic applications

Fabrication of highly conductive and transparent TiO₂/Ag/TiO₂ (referred hereafter as TAT) multilayer films with nitrogen implantation is reported. In the present work, TAT films were fabricated with a total thickness of 100 nm by sputtering on glass substrates at room temperature. The as-deposited films were implanted with 40 keV N ions for different fluences (1×10¹⁴, 5×10¹⁴, 1×10¹⁵, 5×10¹⁵ and 1×10¹⁶ ions/cm²). The objective of this study was to investigate the effect of N⁺ implantation on the optical and electrical properties of TAT multilayer films. X-ray diffraction of TAT films shows an amorphous TiO₂ film with a crystalline peak assigned to Ag (111) diffraction plane. The surface morphology studied by atomic force microscopy (AFM) and field emission scanning electron microscope (FESEM) revealed smooth and uniform top layer of the sandwich structure. The surface roughness of pristine film was 1.7 nm which increases to 2.34 nm on implantation for 1×10¹⁴ ions/cm² fluence. Beyond this fluence, the roughness decreases. The oxide/metal/oxide structure exhibits an average transmittance ~80% for pristine and ~70% for the implanted film at fluence of 1×10¹⁶ ions/cm² in the visible region. The electrical resistivity of the pristine sample was obtained as 2.04×10⁻⁴ Ω cm which is minimized to 9.62×10⁻⁵ Ω cm at highest fluence. Sheet resistance of TAT films decreased from 20.4 to 9.62 Ω/□ with an increase in fluence. Electrical and optical parameters such as carrier concentration, carrier mobility, absorption coefficient, band gap, refractive index and extinction coefficient have been calculated for the pristine and implanted films to assess the performance of films. The TAT multilayer film with fluence of 1×10¹⁶ ions/cm² showed maximum Haacke figure of merit (FOM) of 5.7×10⁻³ Ω⁻¹. X-ray photoelectron spectroscopy (XPS) analysis of N 1s and Ti 2p spectra revealed that substitutional implantation of nitrogen into the TiO₂ lattice added new electronic states just above the valence band which is responsible for the narrowing of band gap resulting in the enhancement in electrical conductivity. This study reports that fabrication of multilayer transparent conducting electrode with nitrogen implantation that exhibits superior electrical and optical properties and hence can be an alternative to indium tin oxide (ITO) for futuristic TCE applications in optoelectronic devices.     

Straightforward synthesis of hierarchical Co3O4@CoWO4/rGO core–shell arrays on Ni as hybrid electrodes for asymmetric supercapacitors

Hierarchical Co₃O₄@CoWO₄/rGO core/shell nanoneedles arrays are successfully grown on 3D nickel foam using a simple, effective method. By virtue of its unique structure, Co₃O₄@CoWO₄/rGO demonstrates an enhanced specific capacitance of 386 F g⁻¹ at 0.5 A g⁻¹ current density. It can be used as an integrated, additive-free electrode for supercapacitors that boasts excellent performance. As illustration, we assemble an asymmetric supercapacitor (ASC) using the as-prepared Co₃O₄@CoWO₄/rGO as the positive electrode and activated carbon as the negative electrode. The optimized ASC displays a maximum energy density of 19.99 Wh kg⁻¹ at a power density of 321 W kg⁻¹. Furthermore, the ASC also presents a remarkably long cycle life along with 88.8% specific capacitance retention after 5000 cycles.     

Tb3+/Yb3+ co-doped Y2O3 upconversion transparent ceramics: Fabrication and characterization for IR excited green emission

Tb³⁺/Yb³⁺ co-doped Y₂O₃ transparent ceramics were fabricated by vacuum sintering of the pellets (prepared from nanopowders by uniaxial pressing) at 1750 °C for 5 h. Zr⁴⁺ and La³⁺ ions were incorporated in Tb³⁺/Yb³⁺ co-doped Y₂O₃ nanoparticle to reduce the formation of pores which limits the transparency of ceramic. An optical transmittance of ∼80% was achieved in ∼450 to 2000 nm range for 1 mm thick pellet which is very close to the theoretical value by taking account of Fresnel’s correction. High intensity luminescence peak at 543 nm (green) was observed in these transparent ceramics under 976 and 929 nm excitations due to Yb–Tb energy transfer upconversion.     

Fiber laser annealing of brush-painted ITO nanoparticles for use as transparent anode for organic solar cells

We report on a fiber laser annealing process for brush-painted ITO nanoparticles, for use as transparent anodes in cost-efficient printable organic solar cells (OSCs). By simple brushing of ITO nanoparticle ink onto glass substrates followed by direct fiber laser annealing, we fabricated solution-processed ITO anodes with a sheet resistance of 56.79 Ω/square and an optical transmittance of 85.77%. The electrical, optical, and structural properties of ITO nanoparticle electrodes were investigated as a function of laser scan speed under a nitrogen ambient. In addition, the detailed microstructure of the laser-annealed ITO electrode was examined to explain the conduction mechanism. OSCs fabricated on laser-annealed ITO electrodes exhibit an open circuit voltage of 0.59 V, short circuit current of 9.02 mA/cm², fill factor of 53.30%, and power conversion efficiency of 2.81%. Successful operation of those OSCs with laser-annealed ITO electrode indicates that fiber laser annealing is a simple and cost-effective option to replace conventional energy-intensive furnace-based annealing processes.     

Enhanced ferroelectric properties of La-substituted BiFeO3 thin films on LaSrCoO3/Pt/TiO2/SiO2/Si (1 0 0) substrates prepared by the soft chemical method

Bi_0.85La_0.15FeO₃ (BLFO015) thin films were deposited by the polymeric precursor solution on La_0.5Sr_0.5CoO₃ substrates. For comparison, the films were also deposited on Pt bottom electrode. X-ray diffraction data confirmed the substitutions of La into the Bi site with the elimination of all secondary phases under a substitution ratio x = 15% at a temperature of 500 °C for 2 h. A substantial increase in the remnant polarization (P_r) with La_0.5Sr_0.5CoO₃ bottom electrode (P_r ≈ 34 μC/cm²) after a drive voltage of 9 V was observed when compared with the same film deposited on Pt substrate. The leakage current behavior at room temperature decreased from 10^?8 (Pt) to 10^?10 A/cm² on (La_0.5Sr_0.5CoO₃) electrode under a voltage of 5 V. The fatigue resistance of the Au/BLFO015/LSCO/Pt/TiO₂/SiO₂/Si (1 0 0) capacitors with a thickness of 280 nm exhibited no degradation after 1 × 10⁸ switching cycles at a frequency of 1 MHz.