Mechanical properties of natural fibre reinforced polyester composites: Jowar,sisal and bamboo

In this paper, the experiments of tensile and flexural tests were carried out on composites made by reinforcing jowar as a new natural fibre into polyester resin matrix. The samples were prepared up to a maximum volume fraction of approximately 0.40 from the fibres extracted by retting and manual process, and compared with established composites like sisal and bamboo developed under similar laboratory conditions. Jowar fibre has a tensile strength of 302 MPa, modulus of 6.99 GPa and an effective density of 922 kg/m³. It was observed that the tensile strength of jowar fibre composite is almost equal to that of bamboo composite, 1.89 times to that of sisal composite and the tensile modulus is 11% and 45% greater than those of bamboo and sisal composites, respectively at 0.40 volume fraction of fibre. The flexural strength of jowar composite is 4%, 35% and the flexural modulus is 1.12 times, 2.16 times greater than those of bamboo and sisal composites, respectively. The results of this study indicate that using jowar fibres as reinforcement in polyester matrix could successfully develop a composite material in terms of high strength and rigidity for light weight applications compared to conventional sisal and bamboo composites.     

Influence of alkali treatment on the interfacial and physico-mechanical properties of industrial hemp fibre reinforced polylactic acid composites

The focus of this work was to produce short (random and aligned) and long (aligned) industrial hemp fibre reinforced polylactic acid (PLA) composites by compression moulding. Fibres were treated with alkali to improve bonding with PLA. The percentage crystallinity of PLA in composites was found to be higher than that for neat PLA and increased with alkali treatment of fibres which is believed to be due to the nucleating ability of the fibres. Interfacial shear strength (IFSS) results demonstrated that interfacial bonding was also increased by alkali treatment of fibres which also lead to improved composite mechanical properties. The best overall properties were achieved with 30 wt.% long aligned alkali treated fibre/PLA composites produced by film stacking technique leading to a tensile strength of 82.9 MPa, Young’s modulus of 10.9 GPa, flexural strength of 142.5 MPa, flexural modulus of 6.5 GPa, impact strength of 9 kJ/m², and a fracture toughness of 3 MPa m^1/2.     

Characterization of thermoplastic natural fibre composites made from woven hybrid yarn prepregs with different weave pattern

This paper focuses on the effect of weave structure on mechanical behaviour and moisture absorption of the PLA/hemp woven fabric composites made by compression moulding. The unidirectional woven fabric prepregs were made from PLA (warp) and PLA/hemp wrapped-spun hybrid yarn (weft) with two different weave patterns; 8-harness satin and basket. Unidirectional composites with 30 mass% hemp content were fabricated from these prepregs, and compared to winded PLA/hemp hybrid yarn laminates with same composition. The composite from the satin fabric had significantly lowest porosities and best mechanical properties compared to the composite made from the winded hybrid yarn and basket fabric. The tensile, flexural, and impact strength were 88 MPa, 113.64 MPa, and 24.24 kJ/m², respectively. The effect of weave pattern on water absorption is significant. Although the composite from hybrid yarn laminate has larger water absorption than that of the pure PLA, it exhibits lower moisture absorption than both weaves.     

The potential of harakeke fibre as reinforcement in polymer matrix composites including modelling of long harakeke fibre composite strength

Mechanical properties of aligned long harakeke fibre reinforced epoxy with different fibre contents were evaluated. Addition of fibre was found to enhance tensile properties of epoxy; tensile strength and Young’s modulus increased with increasing content of harakeke fibre up to 223 MPa at a fibre content of 55 wt% and 17 GPa at a fibre content of 63 wt%, respectively. The flexural strength and flexural modulus increased to a maximum of 223 MPa and 14 GPa, respectively, as the fibre content increased up to 49 wt% with no further increase with increased fibre content. The Rule of Mixtures based model for estimating tensile strength of aligned long fibre composites was also developed assuming composite failure occurred as a consequence of the fracture of the lowest failure strain fibres taking account porosity of composites. The model was shown to have good accuracy for predicting the strength of aligned long natural fibre composites.     

The effect of reprocessing on the mechanical properties of polypropylene reinforced with wood pulp,flax or glass fibre

Composites of polypropylene, substitutable for a given application and reinforced with: Medium Density Fibreboard fibre (MDF) (40 wt%); flax (30 wt%); and glass fibre (20 wt%), were evaluated after 6 injection moulding and extrusion reprocessing cycles. Of the range of tensile, flexural and impact properties examined, MDF composites showed the best mean property retention after reprocessing (87%) compared to flax (72%) and glass (59%). After 1 reprocessing cycle the glass composite had higher tensile strength (56.2 MPa) compared to the MDF composite (44.4) but after 6 cycles the MDF was stronger (35.0 compared to 29.6 MPa for the glass composite). Property reductions were attributed to reduced fibre length. MDF fibres showed the lowest reduction in fibre length between 1 and 6 cycles (39%), compared to glass (51%) and flax (62%). Flax fibres showed greater increases in damage (cell wall dislocations) with reprocessing than was shown by MDF fibres.     

Polyester moulding compounds of natural fibres and wollastonite

Combination of natural fibres and wollastonite whiskers has been attempted as an alternative to glass fibre reinforcement in polyester dough moulding compounds. Natural fibres (sisal) and wollastonite were surface-modified with polyester compatible neo pentyl (diallyl) oxy, tri (dioctyl) pyro-phosphato titanate and gamma-methacryloxy propyl trimethoxy silane coupling agents, respectively. Reinforcing effect of wollastonite to a level of ∼50 wt% in an unsaturated polyester resin reveals a positive indication because of its favourable physico-mechanical properties and microstructural features. The optimization of short sisal and glass fibres in wollastonite/polyester system was carried out to formulate a doughy compound. It was found that ∼11 wt% sisal fibres in wollastonite/polyester and ∼3 to 5 wt% glass fibres in sisal/wollastonite/polyester give the optimum results. The high loss area observed at α and β transitions in dynamic mechanical analyser (DMA) traces supported the elastic behaviour of sisal/wollastonite/polyester moulding compared to corresponding wollastonite/polyester system. Based on these findings, a dough composition has been formulated and its suitability was assessed vis-à-vis to glass fibre–dough moulding compounds. It is observed that polyester dough moulding compound prepared from sisal/wollastonite reinforcement gives satisfactory results.     

Preparation and properties of continuous glass fiber reinforced anionic polyamide-6 thermoplastic composites

Continuous glass fiber (GF) reinforced anionic polyamide-6 (APA6) composites were prepared via in situ ring-opening polymerization of caprolactam monomers. The effects of catalyst content, polymerization temperature and time on the viscosity average molar mass (M_v) and degree of crystallinity (X_c) were investigated in detail. The final mechanical properties of GF/APA6 composites were also studied. The results indicated that both high molecular weight and the high degree of crystallinity of resin matrix lead to the high mechanical properties of composites. Furthermore, the mechanical test results showed that the composites of plain woven fabric had tensile strength of 434 MPa and flexural strength of 407 MPa. The morphologies of tensile fracture surfaces of the composites specimens were observed through Scanning Electron Microscope (SEM). The SEM analysis showed that many disorganized nano-fiber crystals appear in the tensile fracture surfaces, which improve the mechanical properties of the matrix resin. The mechanical properties of the composites with different post-heat treatments were further investigated. The mechanical properties of the composites are significantly reduced after quenching treatment, but hardly improved after annealing.     

Mechanical and morphological properties of fly ash/epoxy composites using conventional thermal and microwave curing methods

Conventional thermal and microwave curing methods were utilized to cure fly ash/epoxy composites, and the mechanical and morphological properties of the composites were evaluated. The conventional thermal curing was performed at 70 °C for 80 min while microwave curing was carried out at 240 W for 18 min in order to achieve the optimum cure of the composites, determined using Differential Scanning Calorimeter. The results suggested that the tensile and flexural moduli of the composites increased with increasing fly ash content while the effect became opposite for tensile, flexural and impact strengths, and tensile strain at break. Improved mechanical properties of the composite could be obtained by addition of N-2(aminoethyl)-3-aminopropyltrimethoxysilane coupling agent, the contents of 0.5 wt% being recommended for the optimum mechanical properties. Beyond these recommended contents, the mechanical properties greatly reduced, except for the flexural modulus. The comparative results indicated that the composites by the microwave cure consumed shorter cure time and had higher ultimate strengths (especially impact strength), and strain at break than those by the conventional thermal cure. The composites with higher tensile and flexural moduli could be obtained by the conventional thermal cure.     

Manufacture and characterisation of thermoplastic composites made from PLA/hemp co-wrapped hybrid yarn prepregs

PLA/hemp co-wrapped hybrid yarns were produced by wrapping PLA filaments around a core composed of a 400 twists/m and 25 tex hemp yarn (Cannabis sativa L) and 18 tex PLA filaments. The hemp content varied between 10 and 45 mass%, and the PLA wrapping density around the core was 150 and 250 turns/m. Composites were fabricated by compression moulding of 0/90 bidirectional prepregs, and characterised regarding porosity, mechanical strength and thermal properties by dynamic mechanical thermal analysis (DMTA) and differential scanning calorimetry (DSC). Mechanical tests showed that the tensile and flexural strengths of the composites markedly increased with the fibre content, reaching 59.3 and 124.2 MPa when reinforced with 45 mass% fibre, which is approximately 2 and 3.3 times higher compared to neat PLA. Impact strength of the composites decreased initially up to 10 mass% fibre; while higher fibre loading (up to 45 mass%) caused an increase in impact strength up to 26.3 kJ/m², an improvement of about 2 times higher compared to neat PLA. The composites made from the hybrid yarn with a wrapping density of 250 turns/m showed improvements in mechanical properties, due to the lower porosity. The fractured surfaces were investigated by scanning electron microscopy to study the fibre/matrix interface.     

The effect of alkaline and silane treatments on mechanical properties and breakage of sisal fibers and poly(lactic acid)/sisal fiber composites

The main goals of this work were to study the effect of different chemical treatments on sisal fiber bundles tensile properties as well as on tensile properties of composites based on poly(lactic acid) (PLA) matrix and sisal fibers. For this purpose, sisal fibers were treated with different chemical treatments. After treating sisal fibers the tensile strength values decreased respect to untreated fiber ones, especially when the combination of NaOH + silane treatment was used. Taking into account fiber tensile properties and fiber/PLA adhesion values, composites based on silane treated fibers would show the highest tensile strength value. However, composites based on alkali treated and NaOH + silane treated fibers showed the highest tensile strength values. Finally, experimental tensile strength values of composites were compared with those values obtained using micromechanical models.     

Controlled retting of hemp fibres: Effect of hydrothermal pre-treatment and enzymatic retting on the mechanical properties of unidirectional hemp/epoxy composites

The objective of this work was to investigate the use of hydrothermal pre-treatment and enzymatic retting to remove non-cellulosic compounds and thus improve the mechanical properties of hemp fibre/epoxy composites. Hydrothermal pre-treatment at 100 kPa and 121 °C combined with enzymatic retting produced fibres with the highest ultimate tensile strength (UTS) of 780 MPa. Compared to untreated fibres, this combined treatment exhibited a positive effect on the mechanical properties of hemp fibre/epoxy composites, resulting in high quality composites with low porosity factor (α_pf) of 0.08. Traditional field retting produced composites with the poorest mechanical properties and the highest α_pf of 0.16. Hydrothermal pretreatment at 100 kPa and subsequent enzymatic retting resulted in hemp fibre composites with the highest UTS of 325 MPa, and stiffness of 38 GPa with 50% fibre volume content, which was 31% and 41% higher, respectively, compared to field retted fibres.     

Mechanical behaviour of jute cloth/wool felts hybrid laminates

This experimental work is aimed at the characterization of new fibre reinforced composites based on epoxy resin with both protein (wool) and lignocellulosic (jute) natural fibres. Wool-based and hybrid (wool/jute) composites with two different stacking sequences (intercalated and sandwich) were developed. Their microstructure has been investigated through optical and scanning electron microscopy, whereas their quasi-static mechanical behaviour has been evaluated in tension and bending. In addition, the impact behaviour under low-velocity impact at three different impact energies, namely 6 J, 8 J and 9 J has been addressed. The tensile and flexural tests have been monitored using acoustic emission (AE) in order to elicit further information about failure mechanisms. AE monitoring showed that development of damage was due to nucleation of matrix microcracks and subsequent debonding and pull-out phenomena in wool fibre composites and that only in hybrid composites a sufficient stress transfer across the jute fibre/matrix interface was achieved. The results confirmed the positive role of hybridization with jute fibres in enhancing both the tensile and flexural behaviour of wool-based composites, though highlighting the need for an improved adhesion between wool fibres and epoxy matrix.     

Effect of short nylon-6 fibres on natural rubber-toughened polystyrene

Composites based on polystyrene and natural rubber at a ratio of 85/15 were prepared by melt mixing with nylon-6 fibres using an internal mixer. The loading of short nylon-6 fibre, untreated and resorcinol formaldehyde latex (RFL)-treated, was varied from 0 to 3 wt.%. Tensile and flexural test samples were punched out from sheets and tested to study the variation of mechanical and dynamic mechanical properties. The tensile behaviour of the composite has been determined at three different strain rates (4.1 × 10⁻⁴ s⁻¹, 2 × 10⁻³ s⁻¹ and 2 × 10⁻² s⁻¹). Both the tensile strength and Young’s modulus of the composite increased with strain rate. The tensile strength, tensile modulus, flexural strength and flexural modulus increased with the increase in fibre content up to 1 wt.%, above which there was a significant deterioration in the properties. The RFL-treated fibre composites showed improved mechanical properties compared to the untreated one. Dynamic mechanical analysis (DMA) showed that the storage modulus of the composite with RFL-treated fibre was better compared to the untreated one. The fibre–matrix morphology of the tensile fractured specimens was studied by scanning electron microscopy (SEM). The results suggested that the RFL treatment of nylon fibre promoted adhesion to the natural rubber phase of the blend, thereby improving the mechanical properties of the composite.     

The effects of the injection moulding temperature on the mechanical properties and morphology of polypropylene man-made cellulose fibre composites

Composites made of polypropylene and man-made cellulose fibres that are intended for injection moulding applications show potential for use in sustainable and light weight engineering with high energy absorption capacity. Due to the thermal sensitivity of the cellulose fibres, process parameters play an important role during the injection moulding process. A polypropylene and a man-made cellulose fibre were chosen for this investigation. Effective melt temperatures between 200 °C and 269 °C were used to process the compounds into test specimens. Tensile, impact and colorimetric tests, as well as an SEM analysis, and a measurement of the fibre length distribution were carried out in order to characterise the mechanical and optical properties of the composites. It was observed that the fibre length becomes shorter above 256 °C and elongation at break and Charpy strength (notched) of the composites already decrease at lower temperatures than tensile strength. A direct correlation between mechanical properties and discoloration was not observed. Therefore, melt temperatures up to 250 °C are suitable for these composites.     

Influence of drying on the mechanical behaviour of flax fibres and their unidirectional composites

The microstructure of flax fibres can be considered as a laminate with layers reinforced by cellulose fibrils. During a single fibre tensile test the S2 layer is subjected to shear. At room temperature, natural fibres contain water absorbed in the cell-walls. This paper examines the influence of this water at two scales: on the tensile behaviour of the flax fibres and on unidirectional plies of flax reinforced epoxy. Drying (24 h at 105 °C) is shown to reduce both failure stress and failure strain significantly. Analysis of normal stresses at the accomodation threshold provides an estimation of the shear strength of secondary cell walls as 45 MPa for fibres containing 6.4% by weight of water and only 9 MPa for dried fibres. Results from tensile tests on unidirectional flax/epoxy composites, reinforced by as-received and dried fibres, confirm the influence of drying on strength properties.     

Influence of fibre type on flexural behaviour of self-compacting fibre reinforced cementitious composites

This paper investigates the flexural properties of self-compacting fibre reinforced cementitious composites that contain high fly ash volume. Seven types of fibres were compared at the same volume fraction and in similar matrices containing high-volume fly ash and having a high compressive strength of around 85 MPa at 28 days. Third-point bending test was conducted on beam specimens to obtain their load–deflection curves, and investigate their fracture behaviour, flexural strength, deflection and toughness. The results showed that using straight steel and micro-polyvinyl alcohol fibres produced composites demonstrating stable deflection-hardening with multiple-cracking phenomenon. This behaviour resulted in high flexural strength, along with large maximum deflection and toughness values, which are important for applications in cementitious composites. This study indicates that fibres with both sufficiently high aspect ratio and high tensile strength are necessary for achieving deflection-hardening in self-compacting cementitious composites with high-strength matrices containing high-volume fly ash.     

Physical and mechanical characterization of Fiber-Reinforced Aerated Concrete (FRAC)

Fiber-Reinforced Aerated Concrete (FRAC) is a novel lightweight aerated concrete that includes internal reinforcement with short polymeric fibers. The autoclaving process is eliminated from the production of FRAC and curing is performed at room temperature. Several instrumented experiments were performed to characterize FRAC blocks for their physical and mechanical properties. This work includes the study of pore-structure at micro-scale and macro-scale; the variations of density and compressive strength within a block; compressive, flexural and tensile properties; impact resistance; and thermal conductivity. Furthermore, the effect of fiber content on the mechanical characteristics of FRAC was studied at three volume fractions and compared to plain Autoclaved Aerated Concrete (AAC). The instrumented experimental results for the highest fiber content FRAC indicated compressive strength of approximately 3 MPa, flexural strength of 0.56 MPa, flexural toughness of more than 25 N m, and thermal conductivity of 0.15 W/K m.     

Effect of pectin and hemicellulose removal from hemp fibres on the mechanical properties of unidirectional hemp/epoxy composites

The objective of this study was to investigate the effect of pectin and hemicellulose removal from hemp fibres on the mechanical properties of hemp fibre/epoxy composites. Pectin removal by EDTA and endo-polygalacturonase (EPG) removed epidermal and parenchyma cells from hemp fibres and improved fibre separation. Hemicellulose removal by NaOH further improved fibre surface cleanliness. Removal of epidermal and parenchyma cells combined with improved fibre separation decreased composite porosity factor. As a result, pectin removal increased composite stiffness and ultimate tensile strength (UTS). Hemicellulose removal increased composite stiffness, but decreased composite UTS due to removal of xyloglucans. In comparison of all fibre treatments, composites with 0.5% EDTA + 0.2% EPG treated fibres had the highest tensile strength of 327 MPa at fibre volume content of 50%. Composites with 0.5% EDTA + 0.2% EPG → 10% NaOH treated fibres had the highest stiffness of 43 GPa and the lowest porosity factor of 0.04.     

The mechanical properties of vinylester resin matrix composites reinforced with alkali-treated jute fibres

Jute fibres were subjected to alkali treatment with 5% NaOH solution for 0, 2, 4, 6 and 8 h at 30°C. The modulus of the jute fibres improved by 12, 68 and 79% after 4, 6 and 8 h of treatment, respectively. The tenacity of the fibres improved by 46% after 6 and 8 h treatment and the % breaking strain was reduced by 23% after 8 h treatment. For 35% composites with 4 h-treated fibres, the flexural strength improved from 199.1 to 238.9 MPa by 20%, modulus improved from 11.89 to 14.69 GPa by 23% and laminar shear strength increased from 0.238 to 0.283 MPa by 19%. On plotting different values of slopes obtained from the rates of improvement of flexural strength and modulus, against NaOH treatment time, two different failure modes were apparent before and after 4 h of NaOH treatment. In the first region between 0 and 4 h, fibre pull out was predominant whereas in the second region between 6 and 8 h, transverse fracture occurred with minimum fibre pull out. This observation was well supported by the SEM investigations of the fracture surfaces.     

Influence of palm oil fuel ash on ultimate flexural and uniaxial tensile strength of green ultra-high performance fiber reinforced cementitious composites

This study focuses on the measurement of the ultimate flexural and tensile strength of GUSMRC, a new class of green ultra-high performance fiber reinforced cementitious composites (GUHPFRCCs) in which 75% of the volume contains ultrafine palm oil fuel ash (UPOFA). This green concrete is currently under development at the Universiti Sains Malaysia (GUSMRC). The main objective of this study is to investigate the potential of UPOFA as a partial binder replacement for the ultimate flexural and uniaxial tensile strength of GUSMRC mixtures. Results showed that UPOFA enhances the flexural and uniaxial tensile responses of fresh UHPFRCCs. The highest flexural and uniaxial tensile strength values at the 50% replacement level after 28 days were at 42.38 MPa and 13.35 MPa, respectively, indicating the potential of utilizing UPOFA as an efficient pozzolanic mineral admixture for the production of GUSMRC with superior engineering properties.