Stack gate PZT/Al2O3 one transistorferroelectric memory

We have developed a single transistor ferroelectric memory using stack gate PZT/Al₂O₃ structure. For the same ~40 Å dielectric thickness, the PZT/Al₂O₃/Si gate dielectric has much better C-V characteristics and larger threshold voltage shift than those of PZT/SiO₂/Si. Besides, the ferroelectric MOSFET also shows a large output current difference between programmed on state and erased off state. The <100 us erase time is much faster than that of flash memory where the switching time is limited by erase time     

Highly reliable, high-C DRAM storage capacitors with CVD TA2O5 films on rugged polysilicon

The authors report on a highly reliable stacked storage capacitor with ultrahigh capacitance using rapid-thermal-annealed low-pressure chemical vapor deposited (LPCVD) Ta₂O₅ films (~100 Å) deposited on NH₃-nitrided rugged poly-Si electrodes. Capacitances as high as 20.4 fF/μ² (corresponding to the thinnest t_ox.eff (16.9 Å) ever reported using LPCVD-Ta₂O₅ and poly-Si technologies) have been achieved with excellent leakage current and time-dependent dielectric breakdown (TDDB) characteristics. Extensive electrical characterization over a wide temperature range (~25-300°C) shows that Ta₂O ₅ films on rugged poly-Si electrodes have a better temperature stability in dielectric leakage and breakdown compared to the films on smooth poly-Si electrodes     

Electrical characteristics of high quality La2O3 gate dielectric with equivalent oxide thickness of 5 Å

Electrical and reliability properties of ultrathin La₂O ₃ gate dielectric have been investigated. The measured capacitance of 33 Å La₂O₃ gate dielectric is 7.2 μF/cm² that gives an effective K value of 27 and an equivalent oxide thickness of 4.8 Å. Good dielectric integrity is evidenced from the low leakage current density of 0.06 A/cm² at -1 V, high effective breakdown field of 13.5 MV/cm, low interface-trap density of 3×10¹⁰ eV^-1/cm², and excellent reliability with more than 10 years lifetime even at 2 V bias. In addition to high K, these dielectric properties are very close to conventional thermal SiO₂      

Bi1.5Zn1.0 Nb1.5O7栅绝缘层的SiO2修饰对ZnO-TFTs性能的影响

具有高介电常数的栅绝缘层材料存在某种极化及耦合作用,使得ZnO-TFTs具有高的界面费米能级钉扎效应、大的电容耦合效应和低的载流子迁移率.为了解决这些问题,本文提出了一种使用SiO₂修饰的Bi_1.5Zn_1.0Nb_1.5O₇作为栅绝缘层的ZnO-TFTs结构,分析了SiO₂修饰对栅绝缘层和ZnO-TFTs性能的影响.结果表明,使用SiO₂修饰后,栅绝缘层和ZnO-TFTs的性能得到显著提高,使得ZnO-TFTs在下一代显示领域中具有非常广泛的应用前景.栅绝缘层的漏电流密度从4.5×10^-5A/cm²降低到7.7×10^-7A/cm²,粗糙度从4.52nm降低到3.74nm,ZnO-TFTs的亚阈值摆幅从10V/dec降低到2.81V/dec,界面态密度从8×10¹³cm^-2降低到9×10¹²cm^-2,迁移率从0.001cm²/（V·s）升高到0.159cm²/（V·s）.     

Transistor characteristics with Ta2O5 gatedielectric

As the gate oxide thickness decreases below 2 nm, the gate leakage current increases dramatically due to direct tunneling current. This large gate leakage current will be an obstacle to reducing gate oxide thickness for the high speed operation of future devices. A MOS transistor with Ta₂O₅ gate dielectric is fabricated and characterized as a possible replacement for MOS transistors with ultra-thin gate silicon dioxide. Mobility, I_d-V_d, I_d-V_g, gate leakage current, and capacitance-voltage (C-V) characteristics of Ta₂O₅ transistors are evaluated and compared with SiO₂ transistors. The gate leakage current is three to five orders smaller for Ta₂O₅ transistors than SiO₂ transistors     

Design optimization of stacked layer dielectrics for minimum gate leakage currents

An effective model to evaluate the leakage currents for different stacked gates deep submicron MOS transistors is presented. For a given equivalent oxide thickness of a stacked gate, the gate leakage current decreases with an increase of high-k dielectric thickness or a decrease of interlayer thickness. Turning points at high gate biases of the I–V curves are observed for Si₃N₄/SiO₂, Ta₂O₅/SiO₂, Ta₂O₅/SiO_2−yN_y, Ta₂O₅/Si₃N₄, and TiO₂/SiO₂ stacked gates except for Al₂O₃/SiO₂ structure. Design optimization for the stacked gate architecture to obtain the minimum gate leakage current is evaluated.     

High-quality MOSFETs with ultrathin LPCVD gate SiO2

MOSFETs and MOS capacitors with ultrathin (65 Å) low-pressure chemical vapor deposition (LPCVD) gate SiO₂ have been fabricated and compared to those with thermal SiO₂ of identical thickness. Results show that the devices with LPCVD SiO₂ have higher transconductance and current drivability, better channel hot-carrier immunity, lower defect density, and better time-dependent dielectric breakdown (TDDB) characteristics than devices with conventional thermal SiO₂     

Charge trapping and degradation in high-permittivityTiO2 dielectric films

Suitable replacement materials for ultrathin SiO₂ in deeply scaled MOSFETs such as lattice polarizable films, which have much higher permittivities than SiO₂, have bandgaps of only 3.0 to 4.0 eV. Due to these small bandgaps, the reliability of these films as a gate insulator is a serious concern. Ramped voltage, time dependent dielectric breakdown (TDDB), and capacitance-voltage (C-V) measurements were done on 190 Å layers of TiO₂ which were deposited through the metal-organic chemical vapor deposition (MOCVD) of titanium tetrakis-isopropoxide. Measurements of the high- and low-frequency capacitance indicate that virtually no interface states are created during constant current injection stress. The increase in leakage current upon electrical stress may be due to the creation of uncharged, near interface states in the TiO₂ film near the SiO₂ interfacial layer that give rise to increased tunneling leakage     

A Comparative Study of HfTaON/SiO2 and HfON/SiO2 Gate Stacks With TaN Metal Gate for Advanced CMOS Applications

The electrical characteristics of a novel HfTaON/SiO₂ gate stack, which consists of a HfTaON film with a dielectric constant of 23 and a 10-Aring SiO₂ interfacial layer, have been investigated for advanced CMOS applications. The HfTaON/SiO₂ gate stack provided much lower gate leakage current against SiO₂ , good interface properties, excellent transistor characteristics, and superior carrier mobility. Compared to HfON/SiO₂, improved thermal stability was also observed in the HfTaON/SiO₂ gate stack. Moreover, charge-trapping-induced threshold voltage V _th instability was examined for the HfTaON/SiO₂ and HfON/SiO₂ gate stacks. The HfTaON/SiO₂ gate stack exhibited significant suppression of the V_th instability compared to the HfON/SiO₂, in particular, for nMOSFETs. The excellent performances observed in the HfTaON/SiO₂ gate stack indicate that it has the potential to replace conventional SiO₂ or SiON as gate dielectric for advanced CMOS applications     

High-performance polycrystalline SiGe thin-film transistors usingAl2O3 gate insulators

The use of aluminum oxide as the gate insulator for low temperature (600°C) polycrystalline SiGe thin-film transistors (TFTs) has been studied. The aluminum oxide was sputtered from a pure aluminum target using a reactive N₂O plasma. The composition of the deposited aluminum oxide was found to be almost stoichiometric (i.e., Al₂O₃), with a very small fraction of nitrogen incorporation. Even without any hydrogen passivation, good TFT performance was measured an devices with 50-nm-thick Al₂O₃ gate dielectric layers. Typically, a field effect mobility of 47 cm²/Vs, a threshold voltage of 3 V, a subthreshold slope of 0.44 V/decade, and an on/off ratio above 3×10⁵ at a drain voltage of 0.1 V can be obtained. These results indicate that the direct interface between the Al₂ O₃ and the SiGe channel layer is sufficiently passivated to make Al₂O₃ a better alternative to grown or deposited SiO₂ for SiGe field effect devices     

Yttrium oxide/silicon dioxide: a new dielectric structure forVLSI/ULSI circuits

Electrical characteristics of Al/yttrium oxide (~260 Å)/silicon dioxide (~40 Å)/Si and Al/yttrium oxide (~260 Å)/Si structures are described. The Al/Y₂O₃/SiO₂/Si (MYOS) and Al/Y₂ O₃/Si (MYS) capacitors show very well-behaved I-V characteristics with leakage current density <10^-10 A/cm² at 5 V. High-frequency C- V and quasistatic C-V characteristics show very little hysteresis for bias ramp rate ranging from 10 to 100 mV/s. The average interface charge density (Q_f+Q _it) is ~6×10¹¹/cm² and interface state density D_it is ~10¹¹ cm^-2-eV^-1 near the middle of the bandgap of silicon. The accumulation capacitance of this dielectric does not show an appreciable frequency dependence for frequencies varying from 10 kHz to 10 MHz. These electrical characteristics and dielectric constant of ~17-20 for yttrium oxide on SiO₂/Si make it a variable dielectric for DRAM storage capacitors and for decoupling capacitors for on-chip and off-chip applications     

Promising storage capacitor structures with thin Ta2O5 film for low-power high-density DRAMs

To ensure the required capacitance for low-power DRAMs (dynamic RAMs) beyond 4 Mb, three kinds of capacitor structures are proposed: (a) poly-Si/SiO₂/Ta₂O₅/SiO₂ /poly-Si or poly-Si/Si₃N₄/Ta₂O ₅/SiO₂/poly-Si (SIS), (b) W/Ta₂O₅ /SiO₂/poly-Si (MIS), and (c) W/Ta₂O₅ W (MIM). The investigation of time-dependent dielectric breakdown and leakage current characteristics indicates that capacitor dielectrics that have equivalent SiO₂ thicknesses of 5, 4, and 3 nm can be applied to 3.3-V operated 16-Mb DRAMs having stacked capacitor cells (STCs) by using SIS, MIS, and MIM structures, respectively, and that 3 and 1.5 nm can be applied to 1.5-V operated 64-Mb DRAMs having STCs by using MIS and MIM structures, respectively. This can be accomplished while maintaining a low enough leakage current for favorable refresh characteristics. In addition, all these capacitors show good heat endurance at 950°C for 30 min. Therefore, these capacitors allow the fabrication of low-power high-density DRAMs beyond 4 Mb using conventional fabrication processes at temperatures up to 950°C. Use of the SIS structure confirms the compatability of the fabrication process of a storage capacitor using Ta₂O₅ film and the conventional DRAM fabrication processes by successful application to the fabrication process of an experimental memory array with 1.5-μm×3.6-μm stacked-capacitor DRAM cells     

SiC MOSFETs with thermally oxidized Ta2Si stacked on SiO2 as high-k gate insulator

In this paper, we compare the electrical characteristics of MOS capacitors and lateral MOSFETs with oxidized Ta₂Si (O-Ta₂Si) as a high-k dielectric on silicon carbide or stacked on thermally grown SiO₂ on SiC. MOS capacitors are used to determine the dielectric and interfacial properties of these insulators. We demonstrate that stacked SiO₂/O-Ta₂Si is an attractive solution for passivation of innovative SiC devices. Ta₂Si deposition and oxidation is totally compatible with standard SiC MOSFET fabrication materials and processing. We demonstrate correct transistor operation for stacked O-Ta₂Si on thin thermally grown SiO₂ oxides. However the channel mobility of such high-k MOSFETs must be improved investigating the interface properties further.     

High-field breakdown in thin oxides grown in N2O ambient

A detailed study of time-dependent dielectric breakdown (TDDB) in N₂O-grown thin (47-120 Å) silicon oxides is reported. A significant degradation in breakdown properties was observed with increasing oxide growth temperatures. A physical model based on undulations at the Si/SiO₂ interface is proposed to account for the degradation. Accelerated breakdown for higher operating temperatures and higher oxide fields as well as thickness dependence of TDDB are studied under both polarities of injection. Breakdown under unipolar and bipolar stress in N₂O oxides is compared with DC breakdown. An asymmetric improvement in time-to-breakdown under positive versus negative gate unipolar stress is observed and attributed to charge detrapping behavior in N₂O oxides. A large reduction in time-to-breakdown is observed under bipolar stress when the thickness is scaled below 60 Å. A physical model is suggested to explain this behavior. Overall, N₂O oxides show improved breakdown properties compared with pure SiO₂     

Low-loss polyimide-Ta2O5-SiO2hybrid ARROW waveguides

A low-loss polyimide-Ta₂O₅-SiO₂ hybrid antiresonant reflecting optical waveguide (ARROW) is presented. The ARROW device was fabricated using both the organic and dielectric thin-film technologies. It consists of the fluorinated polyimide, tantalum pentoxide (Ta₂O₅), and silicon dioxide (SiO₂) hybrid layers deposited on a Si substrate. For transverse electric polarized light, the propagation loss of the waveguide as low as 0.4 dB/cm was obtained at 1.31 μm. The propagation loss for transverse magnetic polarized light is 1.5 dB/cm. An ARROW waveguide fabricated using the polyimide-Ta₂O₅ -polyimide material system is also presented for comparison     

Furnace nitridation of thermal SiO2 in pureN2O ambient for ULSI MOS applications

Furnace nitridation of thermal SiO₂ in pure N₂ O ambient for MOS gate dielectric application is presented. N₂O-nitrided thermal SiO₂ shows much tighter distribution in time-dependent dielectric breakdown (TDDB) characteristics than thermal oxide. MOSFETs with gate dielectric prepared by this method show improved initial performance and enhanced device reliability compared to those with thermal gate oxide. These improvements are attributed to the incorporation of a small amount of nitrogen (~1.5 at.%) at the Si-SiO₂ interface without introducing H-related species during N₂O nitridation     

Optimization of gate oxide N2O anneal for CMOSFET's atroom and cryogenic temperatures

This paper presents a study of the impact of gate-oxide N₂ O anneal on CMOSFET's characteristics, device reliability and inverter speed at 300 K and 85 K. Two oxide thicknesses (60 and 110 Å) and five N₂O anneal conditions (900~950°C, 5~40 min) plus nonnitrided process and channel lengths from 0.2 to 2 μm were studied to establish the correlation between the nitrogen concentration at Si/SiO₂ interface and the relative merits of the resultant devices. We concluded that one simple post-oxidation N₂O anneal step can increase CMOSFET's lifetime by 4~10 times, effectively suppress boron penetration from the P⁺ poly-Si gate of P-MOSFET's without sacrificing CMOS inverter speed. We also found that the benefits in terms of the improved interface hardness and charge trapping characteristic still exist at cryogenic temperature. All these improvements are found to be closely correlated to the nitrogen concentration incorporated at the Si/SiO₂ interface. The optimal N₂O anneal occurs somewhere at around 2% of nitrogen incorporation at Si/SiO₂ interface which can be realized by annealing 60~110 Å oxides at 950°C for 5 min or 900°C for 20 min     

A high-quality stacked thermal/LPCVD gate oxide technology for ULSI

By stacking thermal and high-quality LPCVD (low-pressure chemical vapor deposition) SiO₂ films, gate oxides with very low defect densities are demonstrated. Whereas previous reports suggested that a thick layer of LPCVD oxide can improve the stacked gate oxide defect density, it is demonstrated that even 25 Å of LPCVD oxide is sufficient to dramatically reduce the defect density compared to thermal oxide films. The projected scaling limit for this technology is estimated to be as low as 70 Å for the total stack thickness. An optimized thermal/LPCVD oxide technology is very promising as the gate dielectric for sub-half-micrometer CMOS technology     

Low-temperature polysilicon TFT with two-layer gate insulator usingphoto-CVD and APCVD SiO2

The performance of polysilicon thin-film transistors (TFTs) formed by a 600°C process was improved using a two-layer gate insulator of photochemical-assisted vapor deposition (photo-CVD) SiO₂ and atmospheric-pressure chemical vapor deposition (APCVD) SiO₂. The photo-CVD SiO₂, 100 Å thick, was deposited on polysilicon and followed by APCVD SiO₂ of 1000 Å thickness. The TFT had a threshold voltage of 8.3 V and a field-effect mobility of 35 cm²/V-s, which were higher than those of the conventional TFT with a single-layer gate SiO₂ of APCVD. Hydrogenation by hydrogen plasma was more effective for the new TFT than for the conventional device     

Spatial Distributions of Trapping Centers in HfO2/SiO2 Gate Stack

An analysis methodology for charge pumping (CP) measurements was developed and applied to extract spatial distributions of traps in SiO ₂/HfO₂ gate stacks. This analysis indicates that the traps accessible by CP measurements in the frequency range down to a few kilohertz are located primarily within the SiO₂ layer and HfO₂/SiO₂ interface region. The trap density in the SiO₂ layer increases closer to the high-kappa dielectric, while the trap spatial profile as a function of the distance from the high-kappa film was found to be dependent on high-kappa film characteristics. These results point to interactions with the high-kappa dielectric as a cause of trap generation in the interfacial SiO₂ layer