埋空隙PSOI结构的耐压分析

提出了一种埋空隙PSOI (APSOI) RESURF器件结构,此结构利用空隙相对低的介电系数,在器件纵向突破了传统SiO2埋层的耐压关系,提高了击穿电压;硅窗口的存在缓解了有源区的自热效应;不同衬底的场调制作用进一步优化了表面电场分布. 在相同击穿电压条件下,此结构较一般PSOI结构只需1/4厚度的埋层,当漂移区厚度和埋层厚度均为2μm时可获得600V以上的击穿电压.     

埋空隙PSOI结构的耐压分析

提出了一种埋空隙PSOI(APSOI)RESURF器件结构,此结构利用空隙相对低的介电系数,在器件纵向突破了传统SiO2埋层的耐压关系,提高了击穿电压;硅窗口的存在缓解了有源区的自热效应;不同衬底的场调制作用进一步优化了表面电场分布.在相同击穿电压条件下,此结构较一般PSOI结构只需1/4厚度的埋层,当漂移区厚度和埋层厚度均为2μm时可获得600V以上的击穿电压.     

具有P型埋层PSOI结构的耐压分析

提出了一种具有p型埋层的PSOI器件耐压新结构,称为埋层PSOI(BPSOI).其耐压机理是,通过p型埋层电荷产生的附加电场调制作用,导致表面电场分布中产生新的峰而使击穿电压提高;p型埋层的电中性作用增加了漂移区优化的浓度而使比导通电阻降低.借助二维MEDICI数值分析软件,获得此结构较一般PSOI的击穿电压提高52%～58%、比导通电阻降低45%～48%.     

100V体硅N-LDMOS器件研究

为了设计一款100 V体硅N-LDMOS器件,通过借助Tsuprem-4和Medici软件详细讨论分析了高压N-LDMOS器件衬底浓度、漂移区参数、金属场极板长度等与击穿电压、开态电阻之间的关系,最终得到兼容体硅标准低压CMOS工艺的100 V体硅N-LDMOS最佳结构、工艺参数.折衷考虑到了击穿电压、开态电阻这一对矛盾体以满足设计指标.通过模拟曲线可知该高压器件的关态和开态的击穿电压都达到要求,开启电压为1.5 V,而且完全兼容国内体硅标准低压CMOS工艺,可以很好地应用于各种高压功率集成芯片.     

具有p型埋层PSOI结构的耐压分析

提出了一种具有p型埋层的PSOI器件耐压新结构,称为埋层PSOI(BPSOI).其耐压机理是,通过p型埋层电荷产生的附加电场调制作用,导致表面电场分布中产生新的峰而使击穿电压提高;p型埋层的电中性作用增加了漂移区优化的浓度而使比导通电阻降低.借助二维MEDICI数值分析软件,获得此结构较一般PSOI的击穿电压提高52%～58%、比导通电阻降低45%～48%.     

用于智能功率集成电路的PTG-LDMOST

提出一种用于智能功率集成电路的基于绝缘体上硅(SOI)的部分槽栅横向双扩散MOS晶体管(PTG-LDMOST)。PTG-LDMOST由传统的平面沟道变为垂直沟道,提高了器件击穿电压与导通电阻之间的折衷。垂直沟道将开态电流由器件的表面引向体内降低了导通电阻,而且关态的时候耗尽的JFET区参与耐压,提高单位漂移区长度击穿电压。仿真结果表明:对于相同的10微米漂移区长度,新结构的击穿电压从常规结构的111V增大到192V,增长率为73%。     

SOI-LIGBT N-Buffer参数的研究

基于SOI-LIGBT(Silicon-on-Insulator-Lateral Insulated Gate Bipolar Transistor),采用二维器件模拟软件Tsuprem4和Medici,仿真N-buffer的注入剂量和结深的变化对器件击穿电压和开态电流能力等参数的影响.通过分析,得出实现击穿电压、开态电流和关断时间折中的一般方法和优化N-buffer设计的一般结论.这不仅适用于该器件的设计,而且对其他LIGBT及纵向IGBT器件的N-buffer设计也有所裨益.     

n埋层PSOI结构射频功率LDMOS的输出特性

提出了具有n埋层PSOI(部分SOI)结构的射频功率LDMOS器件.射频功率LDMOS的寄生电容直接影响器件的输出特性.具有n埋层结构的PSOI射频LDMOS,其Ⅰ层下的耗尽层宽度增大,输出电容减小,漏至衬底的结电容比常规LDMOS和PSOI LDMOS分别降低39.1%和26.5%.1dB压缩点处的输出功率以及功率增益比PSOI LDMOS分别提高62%和11.6%,附加功率效率从34.1%增加到37.3%.该结构器件的耐压比体硅LDMOS提高了14%.     

n埋层PSOI结构射频功率LDMOS的输出特性

提出了具有n埋层PSOI(部分SOI)结构的射频功率LDMOS器件.射频功率LDMOS的寄生电容直接影响器件的输出特性.具有n埋层结构的PSOI射频LDMOS,其Ⅰ层下的耗尽层宽度增大,输出电容减小,漏至衬底的结电容比常规LDMOS和PSOI LDMOS分别降低39.1%和26.5%.1dB压缩点处的输出功率以及功率增益比PSOI LDMOS分别提高62%和11.6%,附加功率效率从34.1%增加到37.3%.该结构器件的耐压比体硅LDMOS提高了14%.     

部分耗尽SOI MOSFETs中沟道的非对称掺杂效应

利用二维模拟软件对部分耗尽SoI器件中的非对称掺杂沟道效应进行了模拟.详细地研究了该结构器件的电学性能,如输出特性,击穿特性.通过本文模拟发现部分耗尽SOI非对称掺杂沟道相比传统的部分耗尽SOI,能抑制浮体效应,改善器件的击穿特性.同时跟已有的全耗尽SOI非对称掺杂器件相比,部分耗尽器件性能随参数变化,在工业应用上具有可预见性和可操作性.因为全耗尽器件具有非常薄的硅膜,而这将引起如前栅极跟背栅极的耦合效应和热电子退化等寄生效应.     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

Teleportation of an arbitrary unknown N-qubit entangled state under the controlling of M controllers

A new quantum protocol to teleport an arbitrary unknown N-qubit entangled state from a sender to a fixed receiver under M controllers(M < N) is proposed. The quantum resources required are M non-maximally entangled Greenberger-Home-Zeilinger (GHZ) state and N-M non-maximally entangled Einstein-Podolsky-Rosen (EPR) pairs. The sender performs N generalized Bell-state measurements on the 2N particles. Controllers take M single-particle measurement along x-axis, and the receiver needs to introduce one auxiliary two-level particle to extract quantum information probabilistically with the fidelity unit if controllers cooperate with it.     

Diode-end-pumped Nd:YVO4/LBO lasers with 4.2W continuous-wave output at 457 nm

A continuous-wave (CW) 457 nm blue laser operating at the power of 4.2 W is demonstrated by using a fiber coupled laser diode module pumped Nd: YVO4 and using LBO as the intra-cavity SHG crystal With the optimization of laser cavity and crystal parameters, the laser operates at a very high efficiency. When the pumping power is about 31 W, the output at 457nm reaches 4.2 W, and the optical to optical conversion efficiency is about 13.5% accordingly. The stability of the out putpower is better than 1.2% for 8 h continuously working.     

Call for Papers

正Wireless Body-area Networks The last decade has witnessed the convergence of three giant worlds:electronics,computer science and telecommunications.The next decade should follow this convergence in most of our activities with the generalization of sensor networks.In particular with the progress in medicine,people live longer and the aging of population will push the development of wireless personal networks     

Call for Papers—Feature Topic,Vol.12,No.7,2015

正Information Centric Networking Information-Centric Networking(ICN) is an emerging direction in Future Internet architecture research,gaining significant tractions among academia and industry.Aiming to replace the conventional host-to-host communication model by a data-centric model,ICN treats data content as the first