Synthesis of random and block copolymers of vinyl chloride and vinyl acetate by RAFT miniemulsion polymerizations mediated by a fluorinated xanthate

Reversible addition–fragmentation chain transfer miniemulsion (co)polymerizations of vinyl acetate (VAc) and vinyl chloride (VC) are conducted in the presence of a fluorinated xthanate (X1). VAc miniemulsion polymerization can be well controlled by X1, and PVAc with small polydispersity index (PDI, <1.20) are obtained. X1 also shows well mediative effect to VC‐VAc miniemulsion copolymerization, while the PDI of VC‐VAc copolymer is greater than that of PVAc since a chain transfer rate to VC is greater than that to VAc. PVAc‐b‐PVC copolymers are synthesized by VC miniemulsion polymerizations mediated by X1‐terminated PVAc. PDIs of PVAc‐b‐PVC copolymers are greater than that of PVAc and VC‐VAc random copolymers with close monomer compositions, and increase with the increase of VC conversion. This is caused by the increased chain transfer to monomer and the formation of monomer‐rich and polymer‐rich phases during the VC polymerization stage. As‐prepared PVAc‐b‐PVC copolymers exhibit a micro‐phase separated morphology. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45074.     

Molecular composite of lignin: Miscibility and complex formation of organosolv lignin and its acetates with synthetic polymers containing vinyl pyrrolidone and/or vinyl acetate units

Binary blends and pseudo-complexes of organosolv lignin (OSL) or its acetate (OSL-Ac) with synthetic polymers including poly(vinyl acetate) (PVAc), poly(N-vinyl pyrrolidone) (PVP), and poly(N-vinyl pyrrolidone-co-vinyl acetate) (P(VP-co-VAc)) were prepared by casting from mixed polymer solutions in N,N-dimethylformamide as good solvent and by spontaneous coprecipitation from solutions in tetrahydrofuran (THF) as comparatively poor solvent. Thermal analysis by differential scanning calorimetry showed that OSL was not miscible with PVAc; however, OSL(-Ac) was miscible with PVP to form homogeneous blends irrespective of the degree of acetylation of OSL. OSL formed homogeneous blends with P(VP-co-VAc) with ≥30 mol % of VP contents. Fourier transform infrared spectra measurements for the miscible blends of OSL/PVP revealed the presence of hydrogen bonding interactions between hydroxyls of OSL and carbonyls of VP units. However, there was no evidence for the development of the hydrogen bonding in miscible blends of fully acetylated OSL with PVP. For complexes via THF solutions, its formation was found to be primarily due to a higher frequency of hydrogen bonding interactions. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Physical properties of poly(vinyl chloride)–grafted N‐isopropylacrylamide graft copolymers and corresponding polyblends

The physical properties of poly(vinyl chloride) (PVC) and poly(N‐isopropylacrylamide) [poly(NIPAAm)] blend systems, and their corresponding graft copolymers such as PVC‐g‐NIPAAm, were investigated in this work. The compatible range for PVC–poly(NIPAAm) blend systems is less than 15 wt % poly(NIPAAm). The water absorbencies for the grafted films increase with increase in graft percentage. The water absorbencies for the blend systems increase with increase in poly(NIPAAm) content within the compatible range for the blends, but the absorbencies decrease when the amount of poly(NIPAAm) is more than the compatible range in the blend system. The tensile strengths for the graft copolymers are larger than the corresponding blends. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 170–178, 2000     

Plastification of poly(vinyl chloride) by polymer blending

Blends of poly(vinyl chloride) (PVC) with different copolymers have been studied to obtain a plasticized PVC with improved properties and the absence of plasticizer migration. The copolymers used as plasticizers in the blends were acrylonitrile butadiene rubber, ethylene vinyl acetate (EVA), and ethylene-acrylic copolymer (E-Acry). Blends were studied with regard to their processing, miscibility, and mechanical properties, as a function of blend and copolymer composition. The results obtained were compared with those of equivalent compositions in the PVC/dioctyl phthalate (DOP) system. Better results than PVC/DOP were obtained for PVC/acrylonitrile butadiene rubber blends. The plasticizing effect on PVC of EVA and E-Acry copolymers was similar to that of DOP. It is shown that crosslinking PVC/E-Acry blends or increasing the vinyl acetate content in PVC/EVA blends, are alternatives that can increase the compatibility and mechanical properties of these blends. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 1303–1312, 2000     

Properties of poly(vinyl chloride) blended with an emulsion copolymer of N‐cyclohexylmaleimide and methyl methacrylate

Emulsion‐polymerized copolymers of methyl methacrylate and N‐cyclohexylmaleimide were synthesized and used for blending with poly(vinyl chloride) (PVC) to improve the heat resistance of PVC. The thermal stabilities of the blends with different copolymer contents were characterized by thermogravimetric analysis, torsional braid analysis, and the Vicat softening temperature. The mechanical properties and rheological behavior of the blends were also determined. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 201–205, 2003     

Mechanical properties of poly(vinyl chloride) blends and corresponding graft copolymers

The mechanical properties of the poly (vinyl chloride) (PVC) and poly (glycidyl methacrylate) [poly (GMA)] blend system and the PVC and poly (hydroxyethyl methacrylate) [poly (HEMA)] blend system and their crosslinked films were investigated. At the same time, the mechanical properties for the corresponding graft copolymers such as PVC-g-GMA, PVC-g-HEMA, and their crosslinked films were also investigated in this study. The results showed that the tensile strengths for PVC–poly (GMA) blend systems were higher than those for PVC-g-GMA graft copolymer, and the tensile strengths for PVC-g-HEMA were higher than those for PVC-poly (HEMA) blend systems. However, the mechanical properties for the PVC–poly (GMA) blend system were not affected by the crosslinking of the blend system, but those for PVC-poly (HEMA) and their graft copolymers decreased with an increase of the equivalent ratio ([NCO]/[OH]) of the crosslinker. Finally, the surface hydrophilicity of the PVC-g-HEMA graft copolymer and PVC-poly (HEMA) blends were also assessed through measuring the contact angle. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 67: 307–319, 1998     

Phase behavior and properties of poly(methyl methacrylate)/poly(vinyl acetate) blends prepared via in situ polymerization

Polymer blends composed of poly(methyl methacrylate) (PMMA) and poly(vinyl acetate) (PVAc) were prepared via radical-initiated polymerization of methyl methacrylate (MMA) in the presence of PVAc. Differential scanning calorimetry and dynamic mechanical analysis were employed to investigate the miscibility and phase behavior of the blends. The PMMA/PVAc blends of in situ polymerization were found to be phase separated and exhibited a two-phase structure, although some chain transferring reaction between the components occurred. The phase separation resulted from the solvent effect of MMA during the in situ polymerization, which was confirmed by the investigation of phase behavior based on solution cast blending. Solubility analysis of the polymerized blends indicated that some chain transferring reaction between the components occurred during the polymerization. An abrupt increase in gel content from 21.2 to 72.4 wt % was observed when the inclusion of PVAc increased from 30 to 40 wt %, and the gel component consisted of the component polymers as shown by infrared spectroscopy studies. The thermogravimetric analysis study indicated that the inclusion of a small amount of PVAc gives rise to a marked stabilization effect on the thermal stability. The PMMA/PVAc blends exhibited increased notched impact properties with the inclusion of 5 wt % PVAc. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 675–684, 1998     

Effect of tacticity of poly(methyl methacrylate) on the miscibility with poly(vinyl pyrrolidone)

Isotactic, atactic, and syndiotactic poly(methyl methacrylates) (PMMA) (designated iPMMA, aPMMA, and sPMMA) with approximately the same molecular weight were mixed separately with poly(vinyl pyrrolidone) (PVP) primarily in chloroform to make three polymer blend systems. Differential scanning calorimetry (DSC) was used to study the miscibility of these blends. The results showed that the tacticity of PMMA has a definite impact on its miscibility with PVP. The aPMMA/PVP and sPMMA/PVP blends were found to be miscible because all the prepared films showed composition-dependent glass-transition temperatures (T_g). The glass-transition temperatures of the aPMMA/PVP blends are equal to or lower than weight average and can be qualitatively described by the Gordon–Taylor equation. The glass-transition temperatures of the other miscible blends (i.e., sPMMA/PVP blends) are mostly higher than weight average and can be approximately fitted by the simplified Kwei equation. The iPMMA/PVP blends were found to be immiscible or partially miscible based on the observation of two glass-transition temperatures. The immiscibility is probably attributable to a stronger interaction among isotactic MMA segments because its ordination and molecular packing contribute to form a rigid domain. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 3190–3197, 2001     

Binary blends of poly(vinyl chloride) stabilized by lithium acetate‐thermal studies

A series of blends of poly(vinyl chloride) (PVC) with (1) poly(methyl methacrylate) (PMMA) or (2) polyoxymethylene (POM), with lithium acetate as a stabilizing agent, was investigated by differential scanning calorimetry (DSC), scanning electron microscopy (SEM), and thermogravimetric analysis (TGA), either alone or coupled with Fourier transform infrared (FTIR) spectroscopy. It was found that lithium acetate has a significant effect on the thermal properties of blends under investigation. It causes the initial decomposition temperatures to increase by about 60–150°C for PVC–POM blends, a substantial suppression of the volatile products evolution for PVC/PMMA blends, and an improvement in the surface morphology for both polymer systems by lowering the degree of roughness. The origin of these effects was discussed by analysis of the intermolecular complexation between metal salt and PVC structural arrangements in the blends. Such interactions may lead to the formation of long‐range, directional‐specific structural regularities, which in turn thermally stabilize the whole system (strong interactions model). © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2576–2587, 1999     

Novel multimonomer‐grafted polypropylene preparation and application in polypropylene/poly(vinyl chloride) blends

A novel grafted polymer was prepared in one step through free‐radical melt grafting in a single‐screw extruder. It was shown that the addition of styrene (St) to the melt‐grafting system as a comonomer could significantly enhance the grafting degree of methyl methacrylate (MMA) onto polypropylene (PP) and reduce the degradation of the PP matrix by means of Fourier transform infrared and melt flow rate testing, respectively. Then, the potential of using multimonomer‐grafted PP, which was designated PP‐g‐(St‐co‐MMA), as the compatibilizer in PP/poly(vinyl chloride) (PVC) blends was also examined. In comparison with PP/PVC blends, the average size of the dispersed phase was greatly reduced in grafted polypropylene (gPP)/PVC blends because of the addition of the PP‐g‐(St‐co‐MMA) graft copolymer. The tensile strength of the gPP/PVC blends increased significantly, and the impact strength was unchanged from that of the pure PP/PVC blends. The results of differential scanning calorimetry and scanning electron microscopy suggested that the compatibility of the PP/PVC blends was improved. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Binary blends based on poly(N‐isopropylacrylamide): Miscibility studies with PVA,PVP, and PAA

Blends of poly(vinyl alcohol) (PVA), poly(acrylic acid), (PAA), and poly(vinyl pyrrolidone) (PVP), with poly(N‐isopropylacrylamide) (PNIPAM), were prepared by casting from aqueous solutions. Mechanical properties of PNIPAM/PVA blends were analyzed by stress–strain tests. Differential scanning calorimetry (DSC) and scanning electron microscopy (SEM) were employed to analyze the miscibility between the polymeric pairs. The results revealed that PNIPAM is not miscible with PVA and PVP in the whole range of composition. On the other hand, PNIPAM interacts strongly with PAA forming interpolymer complex due to the formation of cooperative hydrogen bonds. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 743–748, 2004     

Studies on the miscibility and phase structure in blends of poly(epichlorohydrin) and poly(vinyl acetate)

The miscibility of atactic poly(epichlorohydrin) (aPECH) with poly(vinyl acetate) (PVAc) was examined under two different conditions: (i) in dilute solution, using vicometeric measurements and (ii) as cast films, using differential scanning calorimetric (DSC) and FT-infrared spectroscopy. Phase separation on heating, i.e. lower critical solution temperature (LCST) behavior of the aPECH/PVAc blends was examined by the measurement of transmitted light intensity against temperature. From viscosity measurements, the Krigbaum-Wall polymer-polymer interaction (ΔB) was evaluated. The DSC results show that the aPECH/PVAc blends are miscible as evidenced by the observation of a single composition-dependent glass-transition temperature (T_g) which is well described by the Couchman and Gordon Taylor models. The Flory-Huggins interaction parameter (χ₁₂) calculated from the T_g-method was negative and equal to −0.01, indicating a relatively low interaction strength. The FT-IR results match very well with those of DSC. The cloud point phenomenon is thermodynamically driven but phase separation, once taken place, is diffusion controlled in normal accessible time.     

Synthesis of poly(vinyl acetate)‐graft‐polystyrene and application to preparation of porous membranes

Poly(vinyl acetate)–TEMPO (PVAc–TEMPO) macroinitiators were synthesized by bulk polymerization of vinyl acetate in the presence of benzoyl peroxide (BPO) followed by termination with 2,2,6,6‐tetramethyl‐1‐piperidinyloxy (TEMPO). Radicals were mainly transferred to the acetoxy methyl groups in PVAc during the polymerization. The PVAc–TEMPO macroinitiators had several TEMPO‐dormant sites and styrene bulk polymerization with the macroinitiators produced poly(vinyl acetate)‐graft‐polystyrene (PVAc‐g‐PS). All the TEMPO‐dormant sites of PVAc–TEMPO macroinitiators participated in the styrene polymerization with almost equal reactivity. Methanolysis of PVAc‐g‐PS broke the PS branches apart from the PVAc backbone chains. Hydrophobic or hydrophilic porous membranes with controlled pore size could be prepared by removing the PVAc domains or the PS domains from the graft copolymer. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 1658–1667, 2001     

Study of poly(vinyl chloride)/acrylonitrile–styrene–acrylate blends for compatibility,toughness, thermal stability and UV irradiation resistance

A novel rigid poly(vinyl chloride) (PVC)/acrylonitrile–styrene–acrylate (ASA) copolymer blend with good ultraviolet (UV) irradiation resistance and toughness was reported. ASA with good weatherability and toughness was mixed with PVC by conical twin‐screw extruder to improve the UV irradiation resistance and toughness of PVC. The blends were characterized using Fourier‐transform infrared spectra, dynamic mechanical analysis, and scanning electron microscope. Notch Charpy impact test was used to characterize the UV radiation induced changes in toughness. The results showed that ASA was able to toughen PVC with simultaneously improving heat resistance, thermal stabilization, and protecting PVC from irradiation photochemical degradation. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 2143–2151, 2013     

Synthesis of poly[(2‐oxo‐1,3‐dioxolan‐4‐yl)methyl vinyl ether‐co‐N‐phenylmaleimide] and its miscibility in blends with styrene‐acrylonitrile or poly(vinyl chloride)

The aim of the study was to investigate the synthesis of a copolymer bearing cyclic carbonate and its miscibility with styrene/acrylonitrile copolymer (SAN) or poly(vinyl chloride) (PVC). (2‐Oxo‐1,3‐dioxolan‐4‐yl)methyl vinyl ether (OVE) as a monomer was synthesized from glycidyl vinyl ether and CO₂ using quaternary ammonium chloride salts as catalysts. The highest reaction rate was observed when tetraoctylammonium chloride (TOAC) was used as a catalyst. Even at the atmospheric pressure of CO₂, the yield of OVE using TOAC was above 80% after 6 h of reaction at 80°C. The copolymer of OVE and N‐phenylmaleimide (NPM) was prepared by radical copolymerization and was characterized by FTIR and ¹H‐NMR spectroscopies and differential scanning calorimetry (DSC). The monomer reactivity ratios were given as r₁ (OVE) = 0.53–0.57 and r₂ (NPM) = 2.23–2.24 in the copolymerization of OVE and NPM. The films of poly(OVE‐co‐NPM)/SAN and poly(OVE‐co‐NPM)/PVC blends were cast from N‐dimethylformamide. An optical clarity test and DSC analysis showed that poly(OVE‐co‐NPM)/SAN and poly(OVE‐co‐NPM)/PVC blends were both miscible over the whole composition range. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1809–1815, 2000     

Casting solvent effect on crystallization behavior of poly(vinyl acetate)/poly(ethylene oxide) blends: DSC study

Poly(vinyl acetate) (PVAc)/poly(ethylene oxide) (PEO) blends were prepared by casting from either benzene or chloroform. The solvent effects on the crystallization behavior and thermodynamic properties of the blends were studied by the differential scanning calorimeter (DSC). Two grades of PEO with different molecular weights (PEO200 with M_w = 200,000 g/mol and PEO2 with M_n = 2000 g/mol) were used in this work. The thermal analysis revealed that the blends cast from either benzene or chloroform were miscible in the molten state. The crystallization of PEO in the benzene-cast blends was more easily suppressed than it was in the chloroform-cast blends. Furthermore, the benzene-cast blends showed a greater negative value of Flory-Huggins interaction parameter than those cast from chloroform in the PVAc/PEO200 poly-blend system. It was supposed that the benzene-cast blends had more homogeneous morphology. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 64: 411–421, 1997     

Effect of tacticity of poly(methyl methacrylate) on the miscibility with poly(vinyl acetate)

The results of the miscibility between the chemically similar polymers poly(methyl methacrylate) (PMMA) and poly(vinyl acetate) (PVAc) published so far show inconsistent statements concerning miscibility. The problems may be due to differences in molecular weights, tacticity, and preparation methods of the polymers. This investigation was carried out by using either chloroform or tetrahydrofuran (THF) as solvent to prepare the blends, because to our knowledge, nobody has reported any tacticity effect of PMMA on the miscibility with PVAc. Therefore, in this article, different tactic PMMAs were used to mix with PVAc and their miscibility was studied calorimetrically. The results showed little effect of solvent and tacticity. PMMA and PVAc were determined to be almost completely immiscible because of the observation of two T_g's. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 35–39, 2004     

PVC/ABS共混体系力学性能的研究

用冲击试验机、材料试验机和另外一些相关的仪器对PVC/ABS共混体系的力学性能进行了测试、研究,结果发现,PVC/ABS共混体系的性能是组分的函数。ABS的加入改善了PVC/ABS共混体系的力学性能,随着ABS的增加,体系的冲击强度和断裂伸长率明显地提高,而体系的拉伸强度、拉伸模量几乎是随ABS含量的增加而单调地下降。     

Miscibility of biodegradable aliphatic polyester and poly(vinyl acetate) blends

We report miscibility behavior for synthetic biodegradable aliphatic polyester (BDP) and poly(vinyl acetate) (PVAc) blends by investigating their thermal, rheological, and mechanical properties. Two separate glass transition temperature peaks for the BDP/PVAc blends proved that these blend systems are immiscible. From the rheological measurement, the shear viscosity as a function of shear rate is observed to increase with increasing PVAc content in BDP/PVAc blends, since PVAc has a relatively high molecular weight compared to BDP. Moreover, BDP blends with 10 wt % PVAc have excellent mechanical properties. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1348–1352, 2000