Activated persulfate by DBD plasma and activated carbon for the degradation of acid orange Ⅱ

In this study, the effect of activated peroxydisulfate(PDS) by dielectric barrier discharge(DBD) plasma and activated carbon(HGAC) on the removal of acid orange Ⅱ(AOⅡ) was investigated. The effects of applied voltage, PDS dosage, HGAC dosage, initial pH value, and inorganic anions on the removal rate of AOⅡ were discussed. The main free radicals degrading azo dyes during the experiment were also studied. Experimental results show that the removal rate of AOⅡ in DBD/HGAC/PDS synergistic system is much higher than that in the single system. With the applied voltage of 16 kV, HGAC dosage of 1 g l-1, PDS and AOⅡ molar ratio of 200:1, initial pH value of 5.4 and concentration of AOⅡ solution of 20 mg l-1, the removal rate of AOⅡ reached 97.6% in DBD/HGAC/PDS process after 28 min of reaction.Acidic and neutral conditions are beneficial for AOⅡ removal. Sulfate and hydroxyl radicals play an important role in the removal of AOⅡ. Inorganic anions are not conducive to the removal of AOⅡ.     

Decomposition of a gas mixture of four n-alkanes using a DBD reactor

This study investigates the decomposition of a gas mixture of four n-alkanes (n-heptane, n-octane, n-nonane, and n-decane) using a dielectric barrier discharge reactor. We show that the conversion of n-alkanes increased from 7.2% (C₇H₁₆), 9.7% (C₈H₁₈), 8.4% (C₉H₂₀), and 10.5% (C₁₀H₂₂) to 23.8% (C₇H₁₆), 25.0% (C₈H₁₈), 27.9% (C₉H₂₀), and 32.1% (C₁₀H₂₂) when the energy density increased from 84 J l⁻¹ to 324 J l⁻¹. The conversion of n-alkanes when using the gas mixture is close to that found when using a single n-alkane. The influences of reaction temperature and O₂ concentration are also investigated, and the activation energies for the decomposition of each alkane are given.     

Plasma-assisted ammonia synthesis in a packed-bed dielectric barrier discharge reactor: roles of dielectric constant and thermal conductivity of packing materials

In this article, plasma-assisted NH₃ synthesis directly from N₂ and H₂ over packing materials with different dielectric constants (BaTiO₃, TiO₂ and SiO₂) and thermal conductivities (BeO, AlN and Al₂O₃) at room temperature and atmospheric pressure is reported. The higher dielectric constant and thermal conductivity of packing material are found to be the key parameters in enhancing the NH₃ synthesis performance. The NH₃ concentration of 1344 ppm is achieved in the presence of BaTiO₃, which is 106% higher than that of SiO₂, at the specific input energy (SIE) of 5.4 kJ·l⁻¹. The presence of materials with higher dielectric constant, i.e. BaTiO3 and TiO₂ in this work, would contribute to the increase of electron energy and energy injected to plasma, which is conductive to the generation of chemically active species by electron-impact reactions. Therefore, the employment of packing materials with higher dielectric constant has proved to be beneficial for NH₃ synthesis. Compared to that of Al₂O₃, the presence of BeO and AlN yields 31.0% and 16.9% improvement in NH₃ concentration, respectively, at the SIE of 5.4 kJ·l⁻¹. The results of IR imaging show that the addition of BeO decreases the surface temperature of the packed region by 20.5% to 70.3°C and results in an extension of entropy increment compared to that of Al₂O₃, at the SIE of 5.4 kJ·l⁻¹. The results indicate that the presence of materials with higher thermal conductivity is beneficial for NH₃ synthesis, which has been confirmed by the lower surface temperature and higher entropy increment of the packed region. In addition, when SIE is higher than the optimal value, further increasing SIE would lead to the decrease of energy efficiency, which would be related to the exacerbation in reverse reaction of NH₃ formation reactions.     

Microchannel cooling technique for dissipating high heat flux on W/Cu flat-type mock-up for EAST divertor

As an important component of tokamaks, the divertor is mainly responsible for extracting heat and helium ash, and the targets of the divertor need to withstand high heat flux of 10 MW m⁻² for steady-state operation. In this study, we proposed a new strategy, using microchannel cooling technology to remove high heat load on the targets of the divertor. The results demonstrated that the microchannel-based W/Cu flat-type mock-up successfully withstood the thermal fatigue test of 1000 cycles at 10 MW m⁻² with cooling water of 26 l min⁻¹, 30 °C (inlet), 0.8 MPa (inlet), 15 s power on and 15 s dwell time; the maximum temperature on the heat-loaded surface (W surface) of the mock-up was 493 °C, which is much lower than the recrystallization temperature of W (1200 °C). Moreover, no occurrence of macrocrack and 'hot spot' at the W surface, as well as no detachment of W/Cu tiles were observed during the thermal fatigue testing. These results indicate that microchannel cooling technology is an efficient method for removing the heat load of the divertor at a low flow rate. The present study offers a promising solution to replace the monoblock design for the EAST divertor     

Enhanced removal of benzene in nonthermal plasma with ozonation,flow recycling,and flow recirculation

A double stage AC/DC sequential high voltage reactor has been developed to study the decomposition of benzene in the air stream at atmospheric pressure. The removal efficiency was measured as a function of ozonation, flow recycling, and flow recirculation. Ozonation in the inlet, and recycling of the exhaust stream increased the removal of benzene, also with increasing of specific input energy (J l⁻¹) the effect of inlet flow ozonation on benzene decomposition was enhanced. The highest removal efficiency was obtained up to >99% in recirculation six times, while CO₂ selectivity reached 99.9% and energy efficiency was 0.59 g kWh⁻¹. O₃ production/ decomposition > production of OH radicals > electronic and ionic collisions were indicated as the main mechanisms influencing benzene abatement in this research.     

Plasma-facilitated modification of pumpkin vine-based biochar and its application for efficient elimination of uranyl from aqueous solution

An acrylic modified pumpkin vine-based biochar (p-PVB-PAA) is synthesized by non-thermal plasma-grafting modification of pumpkin vine-based biochar (PVB) for the removal of uranyl from an aqueous solution. Microscopic characterization reveals that compared to PVB the surface of p-PVBPAA has more oxygen-containing functional groups by strong chemical bonding and the specific surface area is increased to 275.3 m² g⁻¹ from 3.8 m² g⁻¹. It is found that p-PVB-PAA showed a much higher maximum adsorption capacity for uranyl from aqueous solutions than PVB, which were 207.02 mg g⁻¹ and 67.58 mg g⁻¹ at pH=5 and 298 K, respectively. Moreover, the adsorption behavior follows a pseudo-second-order kinetics model and the Langmuir adsorption model. Additionally, macroscopic experiments and spectroscopic studies verified that the significantly improved adsorption performance of the p-PVB-PAA is due to surface complexation and electrostatic interactions. Furthermore, the very high removal efficiency and excellent regeneration ability (the percentage of the removal still remained at nearly 90% after five cycles) makes this low-cost, easily obtained, and environmentally friendly material attractive for commercial application.     

Enhancing toluene removal in a plasma photocatalytic system through a black TiO_2 photocatalyst

An efficient toluene removal in air using a plasma photocatalytic system(PPS) not only needs favorable surface reactions over photocatalysts under the action of plasma,but also requires the photocatalysts to efficiently absorb light emitted from the discharge for driving the photocatalytic reactions. We report here that the PPS constructed by integrating a black titania(B-TiO_2)photocatalyst with a dielectric barrier discharge(DBD) can effectively remove toluene with above 70% CO_2 selectivity and remarkably reduced the concentration of secondary pollutants of ozone and nitrogen oxides at a specific energy input of 1500 J·l~(-1),while exhibiting good stability. Photocatalyst characterizations suggest that the B-TiO_2 provides a high concentration of oxygen vacancies for the surface oxidation of toluene in DBD,and efficiently absorbs ultraviolet–visible light emitted from the discharge to induce plasma photocatalytic oxidation of toluene. The presence of B-TiO_2 in the plasma region also results in a high discharge efficiency,facilitating the generation of large numbers of reactive species and thus the oxidation of toluene towards CO_2. The greatly enhanced performance of the PPS integrated with B-TiO_2 in toluene removal offers a promising approach to efficiently remove refractory volatile organic compounds from air at low temperatures.     

Application of dielectric barrier discharge (DBD) plasma packed with glass and ceramic pellets for SO2 removal at ambient temperature: optimization and modeling using response surface methodology

Air pollution is a major health problem in developing countries and has adverse effects on human health and the environment. Non-thermal plasma is an effective air pollution treatment technology. In this research, the performance of a dielectric barrier discharge (DBD) plasma reactor packed with glass and ceramic pellets was evaluated in the removal of SO₂ as a major air pollutant from air in ambient temperature. The response surface methodology was used to evaluate the effect of three key parameters (concentration of gas, gas flow rate, and voltage) as well as their simultaneous effects and interactions on the SO₂ removal process. Reduced cubic models were derived to predict the SO₂ removal efficiency (RE) and energy yield (EY). Analysis of variance results showed that the packed-bed reactors (PBRs) studied were more energy efficient and had a high SO₂ RE which was at least four times more than that of the non-packed reactor. Moreover, the results showed that the performance of ceramic pellets was better than that of glass pellets in PBRs. This may be due to the porous surface of ceramic pellets which allows the formation of microdischarges in the fine cavities of a porous surface when placed in a plasma discharge zone. The maximum SO₂ RE and EY were obtained at 94% and 0.81 g kWh⁻¹, respectively under the optimal conditions of a concentration of gas of 750 ppm, a gas flow rate of 2 l min⁻¹, and a voltage of 18 kV, which were achieved by the DBD plasma packed with ceramic pellets. Finally, the results of the model's predictions and the experiments showed good agreement.     

钚沉淀母液中残留草酸根的分析

采用离子色谱作为检测仪器,建立了简便、灵敏的测定草酸钚沉淀母液中残留草酸根的新方法。样品稀释后,首先用羟基脲(HU)还原破坏MnO-4,再过H柱去除阳离子,然后采用5L/min氮吹55℃蒸发的方法去除硝酸干扰,离子色谱仪进行检测。标准曲线在0.01~50mg/L范围内线性良好,相关系数r2=0.996,草酸根的检出限为5.3μg/L。采用建立的方法对模拟样品进行重加回收实验,草酸根回收率在88%~92%之间,0.5mg/L草酸根6次测定的sr=4.0%。该方法操作简单、灵敏度高,为草酸钚沉淀母液中残留草酸根的检测提供了可行的分析方法。     

Research on the real-time signal conditioning method for dispersion interferometer in HL-2M

A new CO₂ laser dispersion interferometer has been developed in the HL-2M tokamak to measure the electron density. In order to meet the needs of high-precision measurement, a data acquisition system with real-time signal conditioning (RSC) method is proposed. It can eliminate part of the impacts of environmental factors, such as mechanical vibration, light path changes, and plasma refraction effect during experiments. In harsh environments, the system can measure the line-integrated density with a high precision of 2 × 10¹⁸ m⁻² with the RSC method. The system has been tested in a recent HL-2A experimental campaign, and the results show that the RSC method plays an important role in the plasma electron density measurement.     

Investigation of electron cyclotron current drive efficiency on the J-TEXT tokamak

Electron cyclotron current drive (ECCD) efficiency research is of great importance for the neoclassical tearing mode (NTM) stabilization. Improving ECCD efficiency is beneficial for the NTM stabilization and the ECCD power threshold reduction. ECCD efficiency has been investigated on the J-TEXT tokamak. The electron cyclotron wave (ECW) power scan was performed to obtain the current drive efficiency. The current drive efficiency is derived to be approximately η₀ = (0.06–0.16) × 10¹⁹ A m⁻² W⁻¹ on the J-TEXT tokamak. The effect of the residual toroidal electric field has been included in the determination of the current drive efficiency, which will enhance the ECCD efficiency. At the plasma current of I_p = 100 kA and electron density of n_e = 1.5 × 10¹⁹ m⁻³, the ratio of Spitzer conductivity between omhic (OH) and ECCD phases is considered and the experimental data have been corrected. The correction results show that the current drive efficiency η1 caused by the fast electron hot conductivity decreases by approximately 79%. It can be estimated that the driven current is approximately 24 kA at 300 kW ECW power.     

In situ quantification of NO synthesis in a warm air glow discharge by WMS-based Mid-IR QCL absorption spectroscopy

Nitric oxide (NO) is one of the most crucial products in the plasma-based nitrogen fixation process. In this work, in situ measurements were performed for quantifying the NO synthesis spatially in a warm air glow discharge, through the method of Mid-infrared quantum cascade laser absorption spectroscopy (QCL-AS). Two ro-vibrational transitions at 1900.076 cm⁻¹ and 1900.517 cm⁻¹ of the ground-state NO(X) were probed sensitively by the help of the wavelength modulation spectroscopy (WMS) approach to increase the signal/noise (S/N) level. The results show a decline trend of NO synthesis rate along the discharge channel from the cathode to the anode. However, from the point of energy efficiency, the cathode region is of significantly low energy efficiency of NO production. Severe disproportionality was found for the high energy consumption but low NO production in the region of cathode area, compared to that in the positive column zone. Further analysis demonstrates the high energy cost of NO production in the cathode region, is ascribed to the extremely high reduced electric field $E/N$ therein not selectively preferable for the processes of vibrational excitation or dissociation of N₂ and O₂ molecules. This drags down the overall energy efficiency of NO synthesis by this typical warm air glow discharge, particularly for the ones with short electrode gaps. Limitations of further improving the energy cost of NO synthesis by variations of the discharge operation conditions, such as discharge current or airflow rate, imply other effective manners able to tune the energy delivery selectively to the NO formation process, are sorely needed.     

Analysis of the critical active species for methylene blue decoloration in a dielectric barrier discharge plasma system

In the paper, a hybrid gas–liquid dielectric barrier discharge (DBD) plasma system was set up to treat a methylene blue (MB) solution. The effects of the change of the carrier gas, the gas bubbling rate and different kinds of scavenger addition, including sodium carbonate (Na₂CO₃), para benzoquinone (p-BQ), triethylenediamine and sodium dihydrogen phosphate (NaH₂PO₄), on the MB decoloration were reviewed to clarify the critical active species for the dye decoloration in the DBD plasma system. The obtained results show that higher decoloration of the MB solution could be achieved when O₂ was used as the carrier gas, which could be 100% after 20 min discharge treatment, and the result confirmed the crucial effect of O₃ in the MB decoloration. Based on the experiments of the scavenger addition, it could be concluded that O₂⁻ and ¹O₂ were two other important reactive oxygen species (ROS) for the MB decoloration. The results of the higher chemical oxygen demand removal and faster disappearance of the characteristic peak of the MB from the UV–vis analysis under O₂ bubbling conditions also proved the critical effect of the ROS formed by O₂ on the MB decoloration.     

Discharge and post-explosion behaviors of electrical explosion of conductors from a single wire to planar wire array

This work deals with an experimental study of a Cu planar wire array (PWA) in air and water under the stored energy 300–1200 J. A single Cu wire is adopted as a controlled trial. Four configurations of PWA and a wire with the same mass (cross-section area) but the different specific surface areas (15–223 cm² g⁻¹) are exploded. The transient process is analyzed using high-speed photography in combination with the results of optical emission and discharge. Discharge characteristics revealed that PWA always has a higher electric power peak, early but higher voltage peak, as well as faster vaporization and ionization process than the single-wire case. Two to three times stronger optical emission could be obtained when replacing the single-wire with PWA, indicating a higher energy-density state is reached. Phenomenologically, in both air and water, single-wire load tends to develop a transverse stratified structure, while PWA is dominated by the uneven energy deposition among wires. Finally, the synchronism and uniformity of the PWA explosion are discussed.     

Inactivation of Staphylococcus aureus by the synergistic action of charged and reactive plasma particles

In this paper, a low-pressure capacitively coupled plasma discharge sustained in an argonoxygen mixture was studied in order to evaluate its properties in terms of inactivation of Staphylococcus aureus. The plasma parameters as electron temperature and plasma density were measured by the Langmuir probe (N_e ≈ 10¹⁵ m⁻³, T_e ≈ 1.5 eV), while the neutral atom density was in the range of 10²¹ m⁻³. In the plasma phase, oxygen radicals were taken as reference of the reactive species with antimicrobial activity, and oxygen spectral lines, over a range of plasma process parameters, were investigated by the optical emission spectroscopy. Optimal plasma conditions were found, and a count reduction of 4 log in a few minutes of the bacterium proves the potentiality of an industrial grade plasma reactor as a sterilization agent.     

Spectral characteristic of laser-induced plasma in soil

The spectral characteristic of laser-induced plasma in soil was studied in this work, laser-induced breakdown spectroscopy was used to analyze the spectral characteristic of plasma under the condition of different time delays and irradiances. Moreover, the time evolution characteristics of plasma temperature and electron density were discussed. Within the time delay range of 0-5 μs,the spectral intensity of the characteristic lines of Si I: 288.158 nm, Ti I: 336.126 nm, Al I:394.400 nm and Fe I: 438.354 nm of the four main elements in two kinds of national standard soil decayed exponentially with time. The average lifetime of the spectral lines was nearly 1.56 μs. Under the condition of different time delays, the spectral intensity of Pb I: 405.78 nm in soil increased linearly with laser energy. However, the slope between the spectral intensity and laser energy decreased exponentially with the increase in time delay, from 4.91 to 0.99 during 0-5 μs. The plasma temperature was calculated by the Boltzmann plot method and the electron density was obtained by inversion of the full width at half maximum of the spectrum. The plasma temperature decreased from 8900 K to 7800 K and the electron density decreased from 1.5 × 10~(17) cm~(-3) to 7.8 × 10~(16) cm~(-3) in the range of 0-5 μs.     

Bright γ-ray source with large orbital angular momentum from the laser near-critical-plasma interaction

We propose a new laser-plasma-based method to generate bright γ-rays carrying large orbital angular momentum by interacting a circularly polarized Laguerre–Gaussian laser pulse with a near-critical hydrogen plasma confined in an over-dense solid tube. In the first stage of the interaction, it is found via fully relativistic three-dimensional particle-in-cell simulations that high-energy helical electron beams with large orbital angular momentum are generated. In the second stage, this electron beam interacts with the laser pulse reflected from the plasma disc behind the solid tube, and helical γ beams are generated with the same topological structure as the electron beams. The results show that the electrons receive angular momentum from the drive laser, which can be further transferred to the γ photons during the interaction. The γ beam orbital angular momentum is strongly dependent on the laser topological charge l and laser intensity a0, which scales as ${L}_{\gamma }\propto {a}_{0}^{4}$. A short (duration of 5 fs) isolated helical γ beam with an angular momentum of −3.3 × 10⁻¹⁴ kg m² s⁻¹ is generated using the Laguerre–Gaussian laser pulse with l = 2. The peak brightness of the helical γ beam reaches 1.22 × 10²⁴ photons s⁻¹ mm⁻² mrad⁻² per 0.1% BW (at 10 MeV), and the laser-to-γ-ray angular momentum conversion rate is approximately 2.1%.     

Mitigation of blackout problem for reentry vehicle in traveling magnetic field with induced current

In this paper, a novel solution mitigating the radio blackout problem is proposed, which improves existing traveling magnetic field (TMF)-based methods. The most significant advance lies in replacing the external injection with self-induced current, which does not require electrodes. The improved analytical model is derived to evaluate the electron density reduction taking into consideration the self-induced current for various TMF velocities. The plasma reduction performance is analyzed for several conditions including the total absence of injected current. The results show that the velocity may be used to trade off the injected current and, when sufficiently large, eliminates the need for an injected current while mitigating radio blackout. The effectiveness of this solution to the blackout problem is demonstrated in commonly used aerospace communication bands. With a field strength of less than 0.15 T, increasing the velocity from 40 m s⁻¹ to 3100 m s⁻¹ is all that is required to obviate the need for an injected current. Moreover, typical reduction ratios for electronic density tolerance (2, 1.9, 1.75 and 3 times for the L-, S-, C- and X-bands, respectively, at an altitude of 40 km) remain unchanged. Increasing the velocity of the TMF is much easier than injecting current via a metal electrode into a high-temperature flow field. The TMF method appears practical in regard to possible future applications.     

1,2,4-trichlorobenzene decomposition using non-thermal plasma technology

Non-thermal plasma(NTP)is regarded as a potential application for environmental pollution control due to its ability to remove pollutants.As a major precursor of dioxins,the influence of the parameters of 1,2,4-trichlorobenzene(TCB)decomposition using NTP technology was investigated through a series of experiments,including voltage,frequency,water content,initial concentration,flow rate,and oxygen content.The experimental results show that the energy injected into the NTP system has a positive correlation to voltage and frequency.Oxygen has the greatest influence on TCB decomposition.The optimal reaction condition was at 15 kV,1000 Hz,an initial concentration of 20 mg m^?3,a flow rate of 2 l min^?1,H2O at 4%,and O2 at 0%.Under this condition,the TCB removal efficiency could reach 92%.According to the generated product backstepping,the hydroxyl radical(·OH)plays an important role in TCB decomposition due to its strong oxidation,which participates in the dechlorination and oxidation reactions as free radicals,and the possible decomposition pathway of TCB by NTP is inferred from the identified byproducts.It is of great significance to investigate the influence of the parameters of TCB decomposition using NTP technology in order to provide references for industrial application.     

Comparison of Reynolds average Navier-Stokes turbulence models in numerical simulations of the DC arc plasma torch

Five turbulence models of Reynolds average Navier-Stokes(RANS),including the standard k-ω model,the RNG k-e model taking into account the low Reynolds number effect,the realizable k-ω model,the SST k-ω model,and the Reynolds stress model(RSM),are employed in the numerical simulations of direct current(DC)arc plasma torches in the range of arc current from 80 A to 240 A and air gas flow rate from 10 m^3 h^-1 to 50 m^3 h^-1.The calculated voltage,electric field intensity,and the heat loss in the arc chamber are compared with the experiments.The results indicate that the arc voltage,the electric field,and the heat loss in the arc chamber calculated by using the standard k-ω model,the RNG k-ωmodel taking into account the low Reynolds number effect,and the realizable k-ω model are much larger than those in the experiments.The RSM predicts relatively close results to the experiments,but fails in the trend of heat loss varying with the gas flow rate.The calculated results of the SST k-ω model are in the best agreement with the experiments,which may be attributed to the reasonable predictions of the turbulence as well as its distribution.