Feasibility of Na-based thermochemical cycles for the capture of CO2 from air—Thermodynamic and thermogravimetric analyses

Three Na-based thermochemical cycles for capturing CO₂ from air are considered: (1) a NaOH/NaHCO₃/Na₂CO₃/Na₂O cycle with 4 reaction steps, (2) a NaOH/NaHCO₃/Na₂CO₃ cycle with 3 reactions steps, and (3) a Na₂CO₃/NaHCO₃ cycle with 2 reaction steps. Depending on the choice of CO₂ sorbent – NaOH or Na₂CO₃ – the cycles are closed by either NaHCO₃ or Na₂CO₃ decomposition, followed by hydrolysis of Na₂CO₃ or Na₂O, respectively. The temperature requirements, energy inputs, and expected products of the reaction steps were determined by thermodynamic equilibrium and energy balance computations. The total thermal energy requirement for Cycles 1, 2, and 3 are 481, 213, and 390 kJ/mol of CO₂ captured, respectively, when heat exchangers are employed to recover the sensible heat of hot streams. Isothermal and dynamic thermogravimetric runs were carried out on the pertinent carbonation, decomposition, and hydrolysis reactions. The extent of the NaOH carbonation with 500 ppm CO₂ in air at 25 °C – applied in Cycles 1 and 2 – reached 9% after 4 h, while that for the Na₂CO₃ carbonation with water-saturated air – applied in Cycle 3 – was 3.5% after 2 h. Thermal decomposition of NaHCO₃ – applied in all three cycles – reached completion after 3 min in the 90–200 °C range, while that of Na₂CO₃ – applied in Cycle 1 – reached completion after 15 min in the 1000–1400 °C range. The significantly slow reaction rates for the carbonation steps and, consequently, the relatively large mass flow rates required, introduce process complications in the scale-up of the reactor technology and impede the application of Na-based sorbents for capturing CO₂ from air.     

Carbon-based catalytic briquettes for the reduction of NO: Effect of H2SO4 and HNO3 carbon support treatment

The influence of treating carbon with sulphuric and nitric acids on the activity of a carbon-based briquette catalyst for NO reduction with NH₃ was examined in a fixed-bed reactor at low temperature (150 °C). The briquette catalysts were prepared from a low-rank coal and a commercial tar pitch. The active phase was impregnated from a suspension of ashes of coke petroleum by means of an equilibrium adsorption method. The catalytic behaviour of NO reduction over acid treated briquettes was found to vary with the surface characteristics of the carbon support. This suggests that the number of oxygen-containing sites as well as vanadium load and dispersion affect the reaction activity. In the presence of oxygen, the SCR activity is enhanced with a nitric acid treatment, activity is promoted by the presence of acidic surface groups such as carboxyl and lactone, which can help not only to create a reservoir of reactants on the catalysts surface but also to improve the dispersion or even increase the amount of vanadium loading. Therefore, the results of this study suggest that the formation of acidic sites on the surface is an important step for NO reduction with NH₃ over carbon-based catalysts. Additional techniques such as XPS and TPD to characterize the oxygen surface and those such as N₂ adsorption to characterize the textural properties were also used in this study.     

The phenol steam reforming reaction towards H2 production on natural calcite

The steam reforming of phenol towards H₂ production was studied in the 650–800 °C range over a natural pre-calcined (air, 850 °C) calcite material. The effects of reaction temperature, water, hydrogen, and carbon dioxide feed concentrations, and gas hourly space velocity (GHSV, h⁻¹) were investigated. The increase of reaction temperature in the 650–800 °C range and water feed concentration in the 40–50 vol% range were found to be beneficial for catalyst activity and H₂-yield. A similar result was also obtained in the case of decreasing the GHSV from 85,000 to 30,000 h⁻¹. The effect of concentration of carbon dioxide and hydrogen in the phenol/water feed stream was found to significantly decrease the rate of phenol steam reforming reaction. The latter was probed to be related to the reduction in the rate of water dissociation as evidenced by the significant decrease in the concentration of adsorbed bicarbonate and OH species on the surface of CaO according to in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS)-CO₂ adsorption experiments in the presence of water and hydrogen in the feed stream. Details of the CO₂ adsorption on the CaO surface at different reaction temperatures and gas atmospheres using in situ DRIFTS and transient isothermal adsorption experiments with mass spectrometry were obtained. Bridged, bicarbonate and unidentate carbonate species were formed under CO₂/H₂O/He gas mixtures at 600 °C with the latter being the most populated. A substantial decrease in the surface concentration of bicarbonate and OH species was observed when the CaO surface was exposed to CO₂/H₂O/H₂/He gas mixtures at 600 °C, result that probes for the inhibiting effect of H₂ on the phenol steam reforming activity. Phenol steam reforming reaction followed by isothermal oxygen titration allowed the measurement of accumulated “carbonaceous” species formed during phenol steam reforming as a function of reaction temperature and short time on stream. An increase in the amount of “carbonaceous” species with reaction time (650–800 °C range) was evidenced, in particular at 800 °C (4.7 vs. 6.7 mg C/g solid after 5 and 20 min on stream, respectively).     

A self-reduced intermediate product from iron and steel plants waste materials using a briquetting process

This study aims to investigate the possible solution for blast furnace flue dust which generates from the Egyptian Iron and Steel Company by forming self-reducing briquettes composed of flue dust and mill scale with different mass ratios, used in electric arc furnace to produce steel. The results indicated that the mechanical properties of the briquettes improved with increasing mill scale ratio in the mixture, whereas the reduction percentages decreased with decreasing temperatures. The addition of coke breeze fines to the briquette mixture (1 mill scale : 1 flue dust) improved the compressive strength of the produced briquette. XRD analysis and microscopic structure of briquette containing 11% coke reduced at 1100 °C for 2 h in isolated atmosphere, showed that the iron phase was predominate phase and the quantity of metallic iron increased.     

Selective methanation of CO over supported Ru catalysts

The catalytic performance of supported ruthenium catalysts for the selective methanation of CO in the presence of excess CO₂ has been investigated with respect to the loading (0.5–5.0 wt.%) and mean crystallite size (1.3–13.6 nm) of the metallic phase as well as with respect to the nature of the support (Al₂O₃, TiO₂, YSZ, CeO₂ and SiO₂). Experiments were conducted in the temperature range of 170–470 °C using a feed composition consisting of 1%CO, 50% H₂ 15% CO₂ and 0–30% H₂O (balance He). It has been found that, for all catalysts investigated, conversion of CO₂ is completely suppressed until conversion of CO reaches its maximum value. Selectivity toward methane, which is typically higher than 70%, increases with increasing temperature and becomes 100% when the CO₂ methanation reaction is initiated. Increasing metal loading results in a significant shift of the CO conversion curve toward lower temperatures, where the undesired reverse water–gas shift reaction becomes less significant. Results of kinetic measurements show that CO/CO₂ hydrogenation reactions over Ru catalysts are structure sensitive, i.e., the reaction rate per surface metal atom (turnover frequency, TOF) depends on metal crystallite size. In particular, for Ru/TiO₂ catalysts, TOFs of both CO (at 215 °C) and CO₂ (at 330 °C) increase by a factor of 40 and 25, respectively, with increasing mean crystallite size of Ru from 2.1 to 4.5 nm, which is accompanied by an increase of selectivity to methane. Qualitatively similar results were obtained from Ru catalysts supported on Al₂O₃. Experiments conducted with the use of Ru catalyst of the same metal loading (5 wt.%) and comparable crystallite size show that the nature of the metal oxide support affects significantly catalytic performance. In particular, the turnover frequency of CO is 1–2 orders of magnitude higher when Ru is supported on TiO₂, compared to YSZ or SiO₂, whereas CeO₂- and Al₂O₃-supported catalysts exhibit intermediate performance. Optimal results were obtained over the 5%Ru/TiO₂ catalyst, which is able to completely and selectively convert CO at temperatures around 230 °C. Addition of water vapor in the feed does not affect CO hydrogenation but shifts the CO₂ conversion curve toward higher temperatures, thereby further improving the performance of this catalyst for the title reaction. In addition, long-term stability tests conducted under realistic reaction conditions show that the 5%Ru/TiO₂ catalyst is very stable and, therefore, is a promising candidate for use in the selective methanation of CO for fuel cell applications.     

Oxy-CO2 reforming of methane to syngas over CoOx/MgO/SA-5205 catalyst

The oxy-CO₂ methane reforming reaction (OCRM) has been investigated over CoO_x supported on a MgO precoated highly macroporous silica–alumina catalyst carrier (SA-5205) at different reaction temperatures (700–900 °C), O₂/CH₄ ratios (0.3–0.45) and space velocites (20,000–100,000 cc/g/h). The reaction temperature had a profound influence on the OCRM performance over the CoO/MgO/SA-5205 catalyst; the methane conversion, CO₂ conversion and H₂ selectivity increased while the H₂/CO ratio decreased markedly with increasing reaction temperature. While the O₂/CH₄ ratio did not strongly affect the CH₄ and CO₂ conversion and H₂ selectivity, it had an intense influence on the H₂/CO ratio. The CH₄ and CO₂ conversion and the H₂ selectivity decreased while the H₂/CO increased with increasing space velocity. The O₂/CH₄ ratio and the reaction temperature could be used to manipulate the heat of the reaction for the OCRM process. Depending on the O₂/CH₄ ratio and temperature the OCRM process could be operated in a mildly exothermic, thermal neutral or mildly endothermic mode. The OCRM reaction became almost thermoneutral at an OCRM reaction temperature of 850 °C, O₂/CH₄ ratio of 0.45 and space velocity of 46,000 cc/g/h. The CH₄ conversion and H₂ selectivity over the CoO/MgO/SA-5205 catalyst corresponding to thermoneutral conditions were excellent: 95% and 97%, respectively with a H₂/CO ratio of 1.8.     

Autothermal reforming of ethanol for hydrogen production over an Rh/CeO2 catalyst

Hydrogen production from ethanol by autothermal reforming over an Rh/CeO₂ catalyst was investigated with a stoichiometric feed composition. Ethanol as well as the reaction intermediates like acetaldehyde and acetone was entirely converted to hydrogen and C1 products at 673 K, and methane steam reforming and reverse water gas shift were the major reactions above 823 K. The Rh/CeO₂ catalyst exhibited stable activity and selectivity during 70 h on-stream operation at 823–923 K without obvious deactivation evidenced by the constant effluent gas composition. Structural analysis of the used catalyst revealed that CeO₂ prevented effectively the highly dispersed Rh particles with sizes of 1–3 nm from sintering and thus maintained sufficient Rh–CeO₂ interfacial areas, which facilitated coke gasification through the high oxygen storage-release capacity.     

Simultaneous desorption–crystallization of CO2–CaCO3 in multi-stage flash (MSF) distillers

In this work, the desorption–crystallization of CO₂–CaCO₃ in MSF distillers was simulated by coupling mass transfer with chemical reaction and correlating the CaCO₃ crystallization rates to the CO₂ release rates. The model was applied to two 20-stage reference MSF once-through and recycles distillers. The CO₂ release rates decreased exponentially from the first stage to the last stage. The CO₂ release rates increased with increasing top brine temperature (TBT) and so CaCO₃ deposition rates did. The CaCO₃ deposition rates increased by 76.9, 102.5 and 123.0 g per ton distillate at 90, 100 and 110 °C, respectively. This corresponded to fouling resistance of 0.64, 0.83 and 1.00 m²K/kW, respectively. The results were fully discussed and interpreted.     

Nitrogen dynamics in paddy field as influenced by free-air CO2 enrichment (FACE) at three levels of nitrogen fertilization

As part of a FACE (free-air CO₂ enrichment) experiment in a rice paddy field in Shizukuishi (Iwate Prefecture, Japan), studies were conducted to determine the effects of elevated CO₂ on N dynamics at three levels of N application. Rice plants were grown under ambient CO₂ or ambient + 200 ppmV CO₂ conditions throughout the growing season in an Andosol soil with each treatment having 4 replicated plots. Three levels of N fertilizer (high, standard and low; 15, 9 and 4 gN m^–2, respectively) were applied to examine different N availability under both CO₂ conditions. Soil samples were collected at 4 different times from upper and lower soil layers (0–1 cm and 1–10 cm soil depths, respectively) and analyzed for microbial biomass N (B_N), mineralizable N (Min. N) and NH₄ ⁺-N in soil. Plant sampling was also done at 3 different times during the growing season to determine the N uptake by plant. Elevated CO₂ significantly increased B_N and Min. N in the upper soil layer at harvest by 25–42% and 18–24%, respectively, compared to ambient CO₂, regardless of N application rate. In low N soil, these significant increases were also observed at the ripening stage. In addition, elevated CO₂ only significantly increased the NH₄ ⁺-N in the upper soil layer at harvest in low N soil compared to ambient CO₂. The N uptake was not significantly affected by CO₂ treatment. These results indicate that elevated CO₂ had significant positive influence on B_N and Min. N in the upper soil layer in paddy soil at the later period of the cropping season at all levels of N application rates, but only at low levels of application rate on NH₄ ⁺-N.     

Study of ruthenium supported on Ta2O5–ZrO2 and Nb2O5–ZrO2 as catalysts for the partial oxidation of methane

Ru-based catalysts supported on Ta₂O₅–ZrO₂ and Nb₂O₅–ZrO₂ are studied in the partial oxidation of methane at 673–873 K. Supports with different Ta₂O₅ or Nb₂O₅ content were prepared by a sol–gel method, and RuCl₃ and RuNO(NO₃)₃ were used as precursors to prepare the catalysts (ca. 2 wt.% Ru). At 673 K high selectivity to CO₂ was found. An increase of temperature up to 773 K produced an increase in the selectivity to syngas (H₂/CO = 2.2–3.1), and this is related with the transformation of RuO₂ to metallic Ru as was determined from XRD and XPS results. At 873 K and with co-fed CO₂ an increase of the catalytic activity and CO selectivity was found. A TOF value of 5.7 s⁻¹ and H₂/CO ratio ca. 1 was achieved over Ru(Cl)/6TaZr. Catalytic results are discussed as a function of the support composition and characteristics of Ru-based phases.     

The positive effect of hydrogen on the reaction of nitric oxide with carbon monoxide over platinum and rhodium catalysts

The effect of adding 330–4930 ppm hydrogen to a reaction mixture of NO and CO (2000 ppm each) over platinum and rhodium catalysts has been investigated at temperatures around 200–250°C. Hydrogen causes large increases in the conversion of NO and, surprisingly, also of CO. Oxygen atoms from the additional NO converted are eventually combined with CO to give CO₂ rather than react with hydrogen to form water. This reaction is described by CO + NO +3/2H₂ CO₂ + NH₃ and accounts for 50–100% of the CO₂ formed with Pt/Al₂O₃ and 20–50% with Rh/Al₂O₃. With the latter catalyst a substantial amount of NO converted produces nitrous oxide. Comparison with a known study of unsupported noble metals suggests that isocyanic acid (HNCO) might be an important intermediate in a reaction system with NO, CO and H₂ present.     

Carbon nanotube-supported Pd–ZnO catalyst for hydrogenation of CO2 to methanol

A type of Pd–ZnO catalysts supported on multi-walled carbon nanotubes (MWCNTs) were developed, with excellent performance for CO₂ hydrogenation to methanol. Under reaction conditions of 3.0 MPa and 523 K, the observed turnover-frequency of CO₂ hydrogenation reached 1.15 × 10⁻² s⁻¹ over the 16%Pd_0.1Zn₁/CNTs(h-type). This value was 1.17 and 1.18 times that (0.98 × 10⁻² and 0.97 × 10⁻² s⁻¹) of the 35%Pd_0.1Zn₁/AC and 20%Pd_0.1Zn₁/γ-Al₂O₃ catalysts with the respective optimal Pd_0.1Zn₁-loading. Using the MWCNTs in place of AC or γ-Al₂O₃ as the catalyst support displayed little change in the apparent activation energy for the CO₂ hydrogenation, but led to an increase of surface concentration of the Pd⁰-species in the form of PdZn alloys, a kind of catalytically active Pd⁰-species closely associated with the methanol generation. On the other hand, the MWCNT-supported Pd–ZnO catalyst could reversibly adsorb a greater amount of hydrogen at temperatures ranging from room temperature to 623 K. This unique feature would help to generate a micro-environment with higher concentration of active H-adspecies at the surface of the functioning catalyst, thus increasing the rate of surface hydrogenation reactions. In comparison with the “Parallel-type (p-type)” MWCNTs, the “Herringbone-type (h-type)” MWCNTs possess more active surface (with more dangling bonds), and thus, higher capacity for adsorbing H₂, which make their promoting action more remarkable.     

Effect of ceria on the structure and catalytic activity of V2O5/TiO2–ZrO2 for oxidehydrogenation of ethylbenzene to styrene utilizing CO2 as soft oxidant

The present study was undertaken to investigate the influence of ceria on the physicochemical and catalytic properties of V₂O₅/TiO₂–ZrO₂ for oxidative dehydrogenation of ethylbenzene to styrene utilizing CO₂ as a soft oxidant. Monolayer equivalents of ceria, vanadia and ceria–vanadia combination over TiO₂–ZrO₂ (TZ) support were impregnated by a coprecipitation and wet impregnation methods. Synthesized catalysts were characterized by using X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy, temperature programmed reduction, transmission electron microscopy and BET surface area methods. The XRD profiles of 550 °C calcined samples revealed amorphous nature of the materials. Upon increasing calcination temperature to 750 °C, in addition to ZrTiO₄ peaks, few other lines due to ZrV₂O₇ and CeVO₄ were observed. The XPS V 2p results revealed the existence of V⁴⁺ and V⁵⁺ species at 550 and 750 °C calcinations temperatures, respectively. TEM analysis suggested the presence of nanosized (<7 nm) particles with narrow range distribution. Raman measurements confirmed the formation ZrTiO₄ under high temperature treatments. TPR measurements suggested a facile reduction of CeO₂–V₂O₅/TZ sample. Among various samples evaluated, the CeO₂–V₂O₅/TZ sample exhibited highest conversion and nearly 100% product selectivity. In particular, the addition of ceria to V₂O₅/TZ suppressed the coke deposition and allowed a stable and high catalytic activity.     

Thermodynamic performance of O2/CO2 gas turbine cycle with chemical recuperation by CO2-reforming of methane

This paper proposes a novel power cycle system composed of chemical recuperative cycle with CO₂–NG (natural gas) reforming and an ammonia absorption refrigeration cycle. In which, the heat is recovered from the turbine exhaust to drive CO₂–NG reformer firstly, and then lower temperature heat from the turbine exhaust is provided with the ammonia absorption refrigeration system to generate chilled media, which is used to cool the turbine inlet gas except export. In this paper, a detailed thermodynamic analysis is carried out to reveal the performance of the proposed cycle and the influence of key parameters on performance is discussed. Based on 1 kg s⁻¹ of methane feedstock and the turbine inlet temperature of 1573 K, the simulation results shown that the optimized net power generation efficiency of the cycle rises up to 49.6% on the low-heating value and the exergy efficiency 47.9%, the new cycle system reached the net electric-power production 24.799 MW, the export chilled load 0.609 MW and 2.743 kg s⁻¹ liquid CO₂ was captured, achieved the goal of CO₂ and NO_x zero-emission.     

FTIR studies on the CO,CO2 and H2 co-adsorption over Ru-RuO x /TiO2 catalyst

FTIR spectra of a Ru-RuO_x/TiO₂ catalyst obtained on co-adsorption of CO, CO₂ and H₂ in the temperature range of 300–500 K were found to be the sum total of corresponding spectra observed during methanation of individual oxides. The two oxides compete for metal sites and at each temperature they reacted simultaneously to form distinct transient Ru(CO)_n type species even though the nature, the stability and the reactivity of these species were different in the two cases. The monocarbonyl species formed during adsorption/reaction of CO alone or of CO + H₂ were bonded more strongly than those formed during CO₂ + H₂ reaction.     

Laser analyses of mixture formation and the influence of solute on particle precipitation in the SAS process

Laser based Raman and elastic light scattering measurements were performed to study the process of mixture formation and the influence of the solute paracetamol onto the phase behaviour of the pseudo-binary system ethanol/CO₂ in the supercritical antisolvent process. From the Raman based technique, mole fraction and partial density distributions of CO₂ were obtained. The mole fraction distributions indicate a rapid mixture formation with fast supersaturation of the solute. At the same time, the increase of the CO₂ partial density at conditions considerably above the mixture critical point (MCP) indicate a change from a homogeneous supercritical to a multi-phase subcritical flow. This phase change goes along with particle precipitation. Thus, the results of our investigations proof, why past approaches failed to generate amorphous paracetamol nanoparticles with the system paracetamol/ethanol/CO₂ above the MCP. Process parameters like injection pressure (20.0–35.0 MPa), chamber pressure of CO₂ (7.5–17.5 MPa), temperature (313–333 K) and solute concentration (0–5 wt%) were varied.     

Improvement of coke resistance of Ni/Al2O3 catalyst in CH4/CO2 reforming by ZrO2 addition

This work investigates the improvement of Ni/Al₂O₃ catalyst stability by ZrO₂ addition for H₂ gas production from CH₄/CO₂ reforming reactions. The initial effect of Ni addition was followed by the effect of increasing operating temperature to 500–700 °C as well as the effect of ZrO₂ loading and the promoted catalyst preparation methods by using a feed gas mixture at a CH₄:CO₂ ratio of 1:1.25. The experimental results showed that a high reaction temperature of 700 °C was favored by an endothermic dry reforming reaction. In this reaction the deactivation of Ni/Al₂O₃ was mainly due to coke deposition. This deactivation was evidently inhibited by ZrO₂, as it enhances dissociation of CO₂ forming oxygen intermediates near the contact between ZrO₂ and nickel where the deposited coke is gasified afterwards. The texture of the catalyst or BET surface area was affected by the catalyst preparation method. The change of the catalyst texture resulted from the formation of ZrO₂–Al₂O₃ composite and the plugging of Al₂O₃ pore by ZrO₂. The 15% Ni/10% ZrO₂/Al₂O₃ co-impregnated catalyst showed a higher BET surface area and catalytic activity than the sequentially impregnated catalyst whereas coke inhibition capability of the promoted catalysts prepared by either method was comparable. Further study on long-term catalyst stability should be made.     

The enantioselective hydrolysis of racemic naproxen methyl ester in supercritical CO2 using Candida rugosa lipase

The enantioselective hydrolysis of racemic naproxen methyl ester by Candida rugosa lipase (CRL) was studied in aqueous buffer solution/isooctane reaction system in the presence of supercritical CO₂. The effects pressure (75–160 bar), temperature (32–42 °C) and reaction time (0.5–12 h) on the enantiomeric excesses of the product (ee_p) and the substrate (ee_s), enantiomeric ratio (E), conversion (x) and enzyme activity were investigated in a batch reactor system. The highest enantiomeric ratio achieved at 120 bar of pressure, 37 °C of temperature and 2 h of reaction time was E = 193 with x = 41.3%, ee_p = 97.9% and ee_s = 68.8%. CRL remained active at least for 12 h at 37 °C and 120 bar in supercritical CO₂ medium. Furthermore, enantiomeric ratio increased with increasing reaction time and reached the value of E = 236 with ee_p = 98.2%, ee_s = 70.0% and x = 41.6% after 12 h of hydrolysis.     

C9-aldehyde hydrogenation over nickel/kieselguhr catalysts in trickle bed reactor

The objective of the present study was to select the optimal catalyst and operating conditions for the manufacture of C₉-alcohol, using C₉-aldehyde and hydrogen, in a trickle bed reactor. When CaO, Ce₂O₃ or MgO was added as a promoter to the Ni/kieselguhr catalyst, the BET and Ni surface areas were increased. In the reaction for the manufacture of C₉-alcohol, using C₉-aldehyde and hydrogen in a batch reactor, a Ni–MgO/kieselguhr catalyst showed the highest activity. In addition, the catalyst using Na₂CO₃ as a precipitant showed the highest activity. According to the result of an experiment to find the optimal reaction conditions for C₉-alcohol synthesis, using C₉-aldehyde and hydrogen in a trickle bed reactor loaded with Ni–MgO/kieselguhr catalyst, the highest yield of C₉-alcohol was 91.5 wt% at 130 °C, 400 psi and WHSV = 3. The C₉-aldehyde hydrogenation performance of the Ni–MgO/kieselguhr catalyst was similar to that of a Cu/ZnO/Al₂O₃ catalyst, but superior to that of Cu–Ni–Cr–Na/Al₂O₃ and Ni–Mo/Al₂O₃ catalysts. In a long-term catalysis test, the Ni–MgO/kieselguhr catalyst showed higher stability than the Cu/ZnO/Al₂O₃ catalyst.     

<Emphasis Type="Italic">In situ</Emphasis> microobservation of the cathode in molten carbonate fuel cells

In molten carbonate fuel cells (MCFC), the wettability of the electrode and the electrolyte distribution are very important factors influencing the active reaction area. We have observed the molten carbonate behaviour directly on the cathode (porous NiO) and the electrolyte plate (LiAlO₂) under various gas conditions and at controlled potentials using an environmental scanning electron microscope (ESEM) equipped with a hot stage. We estimated the liquid electrolyte distribution in the cathode and measured the contact angles on NiO and LiAlO₂ in the electrolyte. Moreover, the electrolyte movement in the reaction CO₂ + O₂ + 2e^– = CO₃ ^2– was observed on the surface of the porous NiO in a CO₂/O₂ atmosphere. The reaction CO₃ ^2– + 2e^– = CO + 2 O^2– of the gas generation was observed in a H₂O atmosphere. The active reaction points on the electrode are the areas where the electrolyte film is thin.