MnO nanorods on graphene as an anode material for high capacity lithium ion batteries

The MnO/graphene hybrid nanocomposites were prepared by an in situ reduction method. The MnO₂ nanorods were attached on the graphene oxides (GOs) to form the MnO₂/GO nanocomposites, which were reduced to the MnO/graphene hybrid under argon atmosphere. As the anode material for the lithium ion batteries, the MnO/graphene electrodes delivered a high initial charge capacity up to 747 mAh g^?1 and a stable capacity of 705.8 mAh g^?1 after 100 cycles, which is much superior to pure MnO with initial charge capacity of 456 mAh g^?1 and the stable capacity of 95.6 mAh g^?1 after 100 cycles. The scanning electron microscope images of the MnO/graphene hybrid nanocomposites after cycling demonstrated that the graphene could prevent the MnO from aggregating during the charge/discharge process.     

3D composites of ZnSnO<Subscript>3</Subscript> nanoplates/reduced graphene oxide aerogels as an advanced lithium-ion battery anode

Zinc-based bimetal oxides have received considerable attention as anode for lithium-ion batteries (LIBs). A one-pot self-assembly hydrothermal method is developed for the fabrication of 3D hierarchical structure aerogels from zinc stannate (ZnSnO₃) and reduced graphene oxide (rGO). 3D interconnected porous structure with ZnSnO₃ hexagon nanoplates uniformly dispersed on graphene sheets has been constructed successfully, in which the crystalline hexagon nanoplates ZnSnO₃ are firstly used to prepare ZnSnO₃-based anode materials for LIBs. The as-prepared ZnSnO₃ nanoplates/reduced graphene oxide aerogels (ZnSnO₃–rGAs) electrode demonstrates an excellent reversible capacity (780 mAh g^?1) after 200 cycles at a certain current density (100 mA g^?1) and still delivers a specific capacity of 460 mAh g^?1 even at 1000 mA g^?1. The superior performance of lithium storage is attributed to the 3D porous hierarchical structure and the synergistic effects of uniform hexagon nanoplates ZnSnO₃ and rGO sheets.     

SnO2 Quantum Dots: Rational Design to Achieve Highly Reversible Conversion Reaction and Stable Capacities for Lithium and Sodium Storage

SnO₂ has been considered as a promising anode material for lithium‐ion batteries (LIBs) and sodium ion batteries (SIBs), but challenging as well for the low‐reversible conversion reaction and coulombic efficiency. To address these issues, herein, SnO₂ quantum dots (≈5 nm) embedded in porous N‐doped carbon matrix (SnO₂/NC) are developed via a hydrothermal step combined with a self‐polymerization process at room temperature. The ultrasmall size in quantum dots can greatly shorten the ion diffusion distance and lower the internal strain, improving the conversion reaction efficiency and coulombic efficiency. The rich mesopores/micropores and highly conductive N‐doped carbon matrix can further enhance the overall conductivity and buffer effect of the composite. As a result, the optimized SnO₂/NC‐2 composite for LIBs exhibits a high coulombic efficiency of 72.9%, a high discharge capacity of 1255.2 mAh g^?1 at 0.1 A g^?1 after 100 cycles and a long life‐span with a capacity of 753 mAh g^?1 after 1500 cycles at 1 A g^?1. The SnO₂/NC‐2 composite also displays excellent performance for SIBs, delivering a superior discharge capacity of 212.6 mAh g^?1 at 1 A g^?1 after 3000 cycles. These excellent results can be of visible significance for the size effect of the uniform quantum dots.     

In situ synthesis of SnO2/graphene nanocomposite and their application as anode material for lithium ion battery

SnO₂/graphene nanocomposite was prepared via an in situ chemical synthesis method. The nanocomposite was characterized by X-ray diffraction, filed emission scanning electron microscope and transmission electron microscope, which revealed that tiny SnO₂ nanoparticles could be homogeneously distributed on the graphene matrix. The electrochemical performance of the SnO₂/graphene nanocomposite as anode material was measured by galvanostatic charge/discharge cycling. The SnO₂/graphene nanocomposite showed a reversible capacity of 665 mAh/g after 50 cycles and an excellent cycling performance for lithium ion battery, which was ascribed to the three-dimensional architecture of SnO₂/graphene nanocomposite. These results suggest that SnO₂/graphene nanocomposite would be a promising anode material for lithium ion battery.     

Ordered mesoporous carbon-supported CoFe<Subscript>2</Subscript>O<Subscript>4</Subscript> composite with enhanced lithium storage properties

A high and stable reversible specific capacity (1277.7 mAh g^?1) was successfully achieved by the CoFe₂O₄/ordered mesoporous carbon nanohybrids (CFO/CMK-3) composite anode at the current density of 0.1 A g^?1 after 100 cycles. CFO/CMK-3 electrode also exhibited a stable capacity up to 733.2 and 482.6 mAh g^?1 at the current densities of 0.5 and 1 A g^?1 after 500 cycles, respectively. The CFO particles were found to be uniformly distributed inside the pore channels of CMK-3. Structure characterization before and after 100 tests revealed that the specific CMK-3 mesoporous structure and CFO crystallites remained unchanged. The stability of the anode composite stability and the rapid redox capability of CFO gave rise to superior lithium storage capacity and excellent cycling stability. CFO/CMK-3 showed a great promise to serve as anode for high-performance lithium-ion battery.     

Hierarchical SnO2 hollow nanotubes as anodes for high performance lithium-ion battery

Nanostructured transition metal oxides are promising anode materials for lithium-ion batteries. Nevertheless, the problem of high volume expansion rate limits its further application. In this paper, we present a 3D hierarchical SnO₂ hollow nanotubes material by calcining C@SnS₂ materials in the air. This structure combines the advantages of both the hollow nanotubes and the outer staggered nanosheets structure, in which the hollow nanotube can provide more lithium ion transport channels, the space between the tubes can buffer the volume change, and the staggering nanosheets structure can effectively improve the relative specific surface area of the material and improve the storage capacity. As a result, the SnO₂ hollow nanotubes anode exhibits the highly reversible capacity of 1079 mAh g^?1 at a current density of 100 mA g^?1, while the reversible specific capacity of 770 mAh g^?1 was obtained after 100 cycles. The research results obtained in this work provide a feasible strategy for synthetic nanoscale transition metal oxide as high-performance lithium anode material.

     

One-step preparation of graphene nanosheets via ball milling of graphite and the application in lithium-ion batteries

An improved method for mass production of good-quality graphene nanosheets (GNs) via ball milling pristine graphite with dry ice is presented. We also report the enhanced performance of these GNs as working electrode in lithium-ion batteries (LIBs). In this improved method, the decrease of necessary ball milling time from 48 to 24 h and the increase of Brunauer–Emmett–Teller surface area from 389.4 to 490 m²/g might be resulted from the proper mixing of stainless steel balls with different diameters and the optimization of agitation speed. The as-prepared GNs are investigated in detail using a number of techniques, such as scanning electron microscope, atomic force microscope, high-resolution transmission electron microscopy, selected area electron diffraction, X-ray diffractometer, and Fourier transform infrared spectroscopic. To demonstrate the potential applications of these GNs, the performances of the LIBs with pure Fe₃O₄ electrode and Fe₃O₄/graphene (Fe₃O₄/G) composite electrode were carefully evaluated. Compared to Fe₃O₄-LIBs, Fe₃O₄/G-LIBs exhibited prominently enhanced performance and a reversible specific capacity of 900 mAh g^?1 after 5 cycles at 100 and 490 mAh g^?1 after 5 cycles at 800 mA g^?1. The improved cyclic stability and enhanced rate capability were also obtained.     

Impact of CTAB on morphology and electrochemical performance of MoS<Subscript>2</Subscript> nanoflowers with improved lithium storage properties

The search for high capacity, low-cost electrode materials for lithium-ion batteries is a significant challenge in energy research. Among the numerous potential candidates, layered compounds such as MoS₂ (Molybdenum Disulfide) have attracted increasing attention. A facile hydrothermal reduction process using hexadecyltrimethy ammonium bromide (CTAB) as surfactant was developed for the synthesis of lithium-ion battery anode material MoS₂ nanoflowers. The impact of CTAB on morphology and electrochemical performance of MoS₂ has been investigated. With the increase of CTAB content, MoS₂ ultrathin nanosheets with high specific surface area and more active sites have been successfully synthesized. Electrochemical measurements demonstrated that MoS₂ nanoflowers synthesized with 1% content of CTAB have better electrochemical performance than others as anode materials for Li-ion batteries, which yield a high discharge capacity of 1245 mAh g^?1 at a current density of 50 mA g^?1 and a stable capacity retention of 740 mAh g^?1 until 100 electrochemical cycles.     

SnO2-reduced graphene oxide nanoribbons as anodes for lithium ion batteries with enhanced cycling stability

A nanocomposite material of SnO2-reduced graphene oxide nanoribbons has been developed. In this composite, the reduced graphene oxide nanoribbons are uniformly coated by nanosized SnO2 that formed a thin layer of SnO2 on the surface. When used as anodes in lithium ion batteries, the composite shows outstanding electrochemical performance with the high reversible discharge capacity of 1,027 mAh/g at 0.1 A/g after 165 cycles and 640 mAh/g at 3.0 A/g after 160 cycles with current rates varying from 0.1 to 3.0 A/g and no capacity decay after 600 cycles compared to the second cycle at a current density of 1.0 A/g. The high reversible capacity, good rate performance and excellent cycling stability of the composite are due to the synergistic combination of electrically conductive reduced graphene oxide nanoribbons and SnO2, The method developed here is practical for the large-scale development of anode materials for lithium ion batteries.     

An activated microporous carbon prepared from phenol-melamine-formaldehyde resin for lithium ion battery anode

Microporous carbon anode materials were prepared from phenol-melamine-formaldehyde resin by ZnCl₂ and KOH activation. The physicochemical properties of the obtained carbon materials were characterized by scanning electron microscope, X-ray diffraction, Brunauer–Emmett–Teller, and elemental analysis. The electrochemical properties of the microporous carbon as anode materials in lithium ion secondary batteries were evaluated. At a current density of 100 mA g^?1, the carbon without activation shows a first discharge capacity of 515 mAh g^?1. After activation, the capacity improved obviously. The first discharge capacity of the carbon prepared by ZnCl₂ and KOH activation was 1010 and 2085 mAh g^?1, respectively. The reversible capacity of the carbon prepared by KOH activation was still as high as 717 mAh g^?1 after 20 cycles, which was much better than that activated by ZnCl₂. These results demonstrated that it may be a promising candidate as an anode material for lithium ion secondary batteries.     

Preparation of yolk–shell Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>@N-doped carbon nanocomposite particles as anode in lithium ion batteries

The yolk–shell-structured Fe₃O₄ nanocomposite particles (Fe₃O₄@Void@C–N NPs) with Fe₃O₄ as the yolk and N-doped carbon as the shell were prepared by using melamine formaldehyde resin as the N and C sources. When used as anode material for lithium ion battery, the yolk–shell structure could not only afford adequate void to accommodate the large volume change during charge/discharge process but also improve structural stability and electrical conductivity. The anode material demonstrated superior long-term and high-rate performance because of the novel structure and the N-doped carbon shell with mesopore. Thus, Fe₃O₄@Void@C–N NPs exhibited a high reversible capacity of 1530 mAh g^?1 after 300 cycles at a current density of 500 mA g^?1, which were approximately 1.5 and 6 times higher than Fe₃O₄@C–N NPs and pure Fe₃O₄ particles, respectively. Even at the higher current density of 2000 mA g^?1, the reversible capacity remained at 651 mAh g^?1 after 500 cycles.     

Large‐Scale Fabrication of Core–Shell Structured C/SnO2 Hollow Spheres as Anode Materials with Improved Lithium Storage Performance

Due to the high theoretical capacity as high as 1494 mAh g^?1, SnO₂ is considered as a potential anode material for high‐capacity lithium–ion batteries (LIBs). Therefore, the simple but effective method focused on fabrication of SnO₂ is imperative. To meet this, a facile and efficient strategy to fabricate core–shell structured C/SnO₂ hollow spheres by a solvothermal method is reported. Herein, the solid and hollow structure as well as the carbon content can be controlled. Very importantly, high‐yield C/SnO₂ spheres can be produced by this method, which suggest potential business applications in LIBs field. Owing to the dual buffer effect of the carbon layer and hollow structures, the core–shell structured C/SnO₂ hollow spheres deliver a high reversible discharge capacity of 1007 mAh g^?1 at a current density of 100 mA g^?1 after 300 cycles and a superior discharge capacity of 915 mAh g^?1 at 500 mA g^?1 after 500 cycles. Even at a high current density of 1 and 2 A g^?1, the core–shell structured C/SnO₂ hollow spheres electrode still exhibits excellent discharge capacity in the long life cycles. Consideration of the superior performance and high yield, the core–shell structured C/SnO₂ hollow spheres are of great interest for the next‐generation LIBs.     

Graphene oxide-decorated Fe<Subscript>2</Subscript>(MoO<Subscript>4</Subscript>)<Subscript>3</Subscript> microflowers as a promising anode for lithium and sodium storage

Mixed transition metal oxides (MTMOs) have received intensive attention as promising anode materials for lithium-ion batteries (LIBs) and sodium-ion batteries (SIBs). In this work, we demonstrate a facile one-step water-bath method for the preparation of graphene oxide (GO) decorated Fe₂(MoO₄)₃ (FMO) microflower composite (FMO/GO), in which the FMO is constructed by numerous nanosheets. The resulting FMO/GO exhibits excellent electrochemical performances in both LIBs and SIBs. As the anode material for LIBs, the FMO/GO delivers a high capacity of 1,220 mAh·g^–1 at 200 mA·g^–1 after 50 cycles and a capacity of 685 mAh·g^–1 at a high current density of 10 A·g^–1. As the anode material for SIBs, the FMO/GO shows an initial discharge capacity of 571 mAh·g^–1 at 100 mA·g^–1, maintaining a discharge capacity of 307 mAh·g^–1 after 100 cycles. The promising performance is attributed to the good electrical transport from the intimate contact between FMO and graphene oxide. This work indicates that the FMO/GO composite is a promising anode for high-performance lithium and sodium storage.

Open image in new window

     

3D Graphene Networks Encapsulated with Ultrathin SnS Nanosheets@Hollow Mesoporous Carbon Spheres Nanocomposite with Pseudocapacitance‐Enhanced Lithium and Sodium Storage Kinetics

The lithium and sodium storage performances of SnS anode often undergo rapid capacity decay and poor rate capability owing to its huge volume fluctuation and structural instability upon the repeated charge/discharge processes. Herein, a novel and versatile method is described for in situ synthesis of ultrathin SnS nanosheets inside and outside hollow mesoporous carbon spheres crosslinked reduced graphene oxide networks. Thus, 3D honeycomb‐like network architecture is formed. Systematic electrochemical studies manifest that this nanocomposite as anode material for lithium‐ion batteries delivers a high charge capacity of 1027 mAh g^?1 at 0.2 A g^?1 after 100 cycles. Meanwhile, the as‐developed nanocomposite still retains a charge capacity of 524 mAh g^?1 at 0.1 A g^?1 after 100 cycles for sodium‐ion batteries. In addition, the electrochemical kinetics analysis verifies the basic principles of enhanced rate capacity. The appealing electrochemical performance for both lithium‐ion batteries and sodium‐ion batteries can be mainly related to the porous 3D interconnected architecture, in which the nanoscale SnS nanosheets not only offer decreased ion diffusion pathways and fast Li⁺/Na⁺ transport kinetics, but also the 3D interconnected conductive networks constructed from the hollow mesoporous carbon spheres and reduced graphene oxide enhance the conductivity and ensure the structural integrity.     

Carbon nanotubes anchored with SnO2 nanosheets as anode for enhanced Li-ion storage

The carbon nanotubes (CNTs) anchored with SnO₂ nanosheets were prepared using a hydrothermal method. The as-prepared products were characterized by X-ray diffraction, fourier transform infrared spectroscopy, thermogravimetric analyses, field emission scanning electron microscope and transmission electron microscope. The electrochemical performances of SnO₂ nanosheets/CNTs composite were measured by galvanostatic charge/discharge cycling, cyclic voltammetry and electrochemical impedance spectroscopy. The results show that the SnO₂ nanosheets/CNTs composite maintains high lithium storage capacity and good cycling stability. The designed structure plays key role in improving electrochemical performance. The CNTs anchored with SnO₂ nanosheets will be an ideal candidate of anode material for lithium ion batteries.     

用于锂离子电池的高性能SiOx/C/石墨烯复合负极材料

以SiO、丁苯橡胶(SBR)及石墨烯为原料,通过高温歧化、机械球磨、喷雾干燥和高温热解制备电化学性能优异的锂离子电池SiO_x/C/石墨烯复合负极材料。采用X射线衍射仪(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、X射线能谱仪(EDS)和恒流充放电测试仪对复合材料的物相、颗粒形貌及电化学性能等进行表征。结果表明,热解后的SiO_x/C/石墨烯复合负极材料的首次放电容量为1 807mAh/g,100次循环后,可逆容量高达1 349mAh/g,库伦效率为99.1%,循环稳定性远高于SiO_x/C和SiO_x/C/graphene前驱体,具有良好的倍率性能。     

Fe2VO4 Hierarchical Porous Microparticles Prepared via a Facile Surface Solvation Treatment for High‐Performance Lithium and Sodium Storage

Preventing the aggregation of nanosized electrode materials is a key point to fully utilize the advantage of the high capacity. In this work, a facile and low‐cost surface solvation treatment is developed to synthesize Fe₂VO₄ hierarchical porous microparticles, which efficiently prevents the aggregation of the Fe₂VO₄ primary nanoparticles. The reaction between alcohol molecules and surface hydroxy groups is confirmed by density functional theory calculations and Fourier transform infrared spectroscopy. The electrochemical mechanism of Fe₂VO₄ as lithium‐ion battery anode is characterized by in situ X‐ray diffraction for the first time. This electrode material is capable of delivering a high reversible discharge capacity of 799 mA h g^?1 at 0.5 A g^?1 with a high initial coulombic efficiency of 79%, and the capacity retention is 78% after 500 cycles. Moreover, a remarkable reversible discharge capacity of 679 mA h g^?1 is achieved at 5 A g^?1. Furthermore, when tested as sodium‐ion battery anode, a high reversible capacity of 382 mA h g^?1 can be delivered at the current density of 1 A g^?1, which still retains at 229 mA h g^?1 after 1000 cycles. The superior electrochemical performance makes it a potential anode material for high‐rate and long‐life lithium/sodium‐ion batteries.     

Structure and electrochemical performance of ZnO/CNT composite as anode material for lithium-ion batteries

Metal oxides are well-known potential alternatives to graphite as anode materials of lithium-ion batteries, and they can deliver much higher reversible capacities than graphite even at high current densities. In this study, hexagonal disk-shaped ZnO are synthesized by a facile solution reaction of ZnCl₂ and its composite is prepared in the presence of carbon nanotubes (CNTs). The as prepared ZnO/CNT composite has been characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, fourier transform-infrared spectroscopy and Rutherford backscattering spectroscopy. Electrochemical characterization by cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic discharge/charge tests demonstrate that the conversion reactions in ZnO and ZnO/CNT electrodes enable reversible capacity of 478 and 602 mAh g^?1, respectively for up to 50 cycles. Our investigation highlights the importance of anchoring of small ZnO particles on CNTs for maximum utilization of electrochemically active ZnO and CNTs for energy storage application in lithium-ion batteries.     

Novel 2D Layered Molybdenum Ditelluride Encapsulated in Few‐Layer Graphene as High‐Performance Anode for Lithium‐Ion Batteries

Molybdenum ditelluride nanosheets encapsulated in few‐layer graphene (MoTe₂/FLG) are synthesized by a simple heating method using Te and Mo powder and subsequent ball milling with graphite. The as‐prepared MoTe₂/FLG nanocomposites as anode materials for lithium‐ion batteries exhibit excellent electrochemical performance with a highly reversible capacity of 596.5 mAh g^?1 at 100 mA g^?1, a high rate capability (334.5 mAh g^?1 at 2 A g^?1), and superior cycling stability (capacity retention of 99.5% over 400 cycles at 0.5 A g^?1). Ex situ X‐ray diffraction and transmission electron microscopy are used to explore the lithium storage mechanism of MoTe₂. Moreover, the electrochemical performance of a MoTe₂/FLG//0.35Li₂MnO₃·0.65LiMn_0.5Ni_0.5O₂ full cell is investigated, which displays a reversible capacity of 499 mAh g^?1 (based on the MoTe₂/FLG mass) at 100 mA g^?1 and a capacity retention of 78% over 50 cycles, suggesting the promising application of MoTe₂/FLG for lithium‐ion storage. First‐principles calculations exhibit that the lowest diffusion barrier (0.18 eV) for lithium ions along pathway III in the MoTe₂ layered structure is beneficial for improving the Li intercalation/deintercalation property.     

Preparation of MoS2‐Coated Three‐Dimensional Graphene Networks for High‐Performance Anode Material in Lithium‐Ion Batteries

A novel composite, MoS₂‐coated three‐dimensional graphene network (3DGN), referred to as MoS₂/3DGN, is synthesized by a facile CVD method. The 3DGN, composed of interconnected graphene sheets, not only serves as template for the deposition of MoS₂, but also provides good electrical contact between the current collector and deposited MoS₂. As a proof of concept, the MoS₂/3DGN composite, used as an anode material for lithium‐ion batteries, shows excellent electrochemical performance, which exhibits reversible capacities of 877 and 665 mAh g^?1 during the 50^th cycle at current densities of 100 and 500 mA g^?1, respectively, indicating its good cycling performance. Furthermore, the MoS₂/3DGN composite also shows excellent high‐current‐density performance, e.g., depicts a 10^th‐cycle capacity of 466 mAh g^?1 at a high current density of 4 A g^?1.