Highly Conductive PEDOT:PSS Electrode with Optimized Solvent and Thermal Post‐Treatment for ITO‐Free Organic Solar Cells

Highly conductive poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) films as stand‐alone electrodes for organic solar cells have been optimized using a solvent post‐treatment method. The treated PEDOT:PSS films show enhanced conductivities up to 1418 S cm^?1, accompanied by structural and chemical changes. The effect of the solvent treatment on PEDOT:PSS has been investigated in detail and is shown to cause a reduction of insulating PSS in the conductive polymer layer. Using these optimized electrodes, ITO‐free, small molecule organic solar cells with a zinc phthalocyanine (ZnPc):fullerene C₆₀ bulk heterojunction have been produced on glass and PET substrates. The system was further improved by pre‐heating the PEDOT:PSS electrodes, which enhanced the power conversion efficiency to the values obtained for solar cells on ITO electrodes. The results show that optimized PEDOT:PSS with solvent and thermal post‐treatment can be a very promising electrode material for highly efficient flexible ITO‐free organic solar cells.     

Photovoltaic Devices: Highly Conductive PEDOT:PSS Electrode with Optimized Solvent and Thermal Post‐Treatment for ITO‐Free Organic Solar Cells (Adv. Funct. Mater. 6/2011)

Highly conductive poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) films as stand‐alone electrodes for organic solar cells have been optimized using a solvent post‐treatment method. The treated PEDOT:PSS films show enhanced conductivities up to 1418 S cm^?1, accompanied by structural and chemical changes. The effect of the solvent treatment on PEDOT:PSS has been investigated in detail and is shown to cause a reduction of insulating PSS in the conductive polymer layer. Using these optimized electrodes, ITO‐free, small molecule organic solar cells with a zinc phthalocyanine (ZnPc):fullerene C₆₀ bulk heterojunction have been produced on glass and PET substrates. The system was further improved by pre‐heating the PEDOT:PSS electrodes, which enhanced the power conversion efficiency to the values obtained for solar cells on ITO electrodes. The results show that optimized PEDOT:PSS with solvent and thermal post‐treatment can be a very promising electrode material for highly efficient flexible ITO‐free organic solar cells.     

High efficiency bulk heterojunction organic solar cell by using high conductivity modified PEDOT: PSS as a buffer layer

In this paper,bulk heterojunction solar cells with poly-(3-hexylthiophene)(P3HT):[6,6]-phenyl-C61-butyric-acid-methylester(PCBM) as an active layer and modified poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate)(PEDOT:PSS) as a buffer layer are fabricated.The buffer layer is modified by adding 1% to 5% dimethyl sulfoxide(DMSO) into PEDOT:PSS solution before spin-coating.The conductivity of modified PEDOT:PSS and the performance of solar cells with modified PEDOT:PSS are measured.The highest conductivity of modified PEDOT:PSS with 4% DMSO can achieve 89.693 S/cm.The performance of organic solar cell with PEDOT:PSS modified by 4% DMSO is the best.The 4% DMSOmodified-PEDOT:PSS cell has a power conversion efficiency of 3.34%,V oc of 5.7 V,J sc of 14.56 mA/cm 2 and filling factor(FF) of 40.34%.     

Interface Modification to Improve Hole‐Injection Properties in Organic Electronic Devices

The performance of organic electronic devices is often limited by injection. In this paper, improvement of hole injection in organic electronic devices by conditioning of the interface between the hole‐conducting layer (buffer layer) and the active organic semiconductor layer is demonstrated. The conditioning is performed by spin‐coating poly(9,9‐dioctyl‐fluorene‐co‐N‐ (4‐butylphenyl)‐diphenylamine) (TFB) on top of the poly(3,4‐ethylene dioxythiophene): poly(styrene sulfonate) (PEDOT:PSS) buffer layer, followed by an organic solvent wash, which results in a TFB residue on the surface of the PEDOT:PSS. Changes in the hole‐injection energy barriers, bulk charge‐transport properties, and current–voltage characteristics observed in a representative PFO‐based (PFO: poly(9,9‐dioctylfluorene)) diode suggest that conditioning of PEDOT:PSS surface with TFB creates a stepped electronic profile that dramatically improves the hole‐injection properties of organic electronic devices.     

High-efficiency inverted polymer solar cells via dual effects of introducing the high boiling point solvent and the high conductive PEDOT:PSS layer

Polymer solar cells (PSCs) are of great interest in the past decade owing to their potentially low-cost in the manufacturing by the solution-based roll to roll method. In this paper, a novel inverted device structure was introduced by inserting a high conductive PEDOT:PSS (hcPEDOT:PSS) layer between the Au nanoparticles (NPs)-embedded hole transport layer (PEDOT:PSS) and the top electrode layer. Power conversion efficiency (PCE) initially reached up to 4.51%, illustrating ∼10% higher compared with the device similarly enhanced by Au NPs plasmonics where only one PEDOT:PSS layer with the embedded Au NPs was used in single bulk heterojunction inverted PSCs based on the poly(3-hexylthiophene):[6,6]-phenyl C61-butyric acid methylester (P3HT:PCBM). The PCE was further improved from 4.51% to 5.01% by adding the high-boiling point solvent of 1,8-diiodooctane (DD) into the active layer, presenting ∼20% enhancement in PCE through dual effects of introducing the high boiling point solvent and the high conductive PEDOT:PSS layer. Morphologies of the active layers were characterised by SEM and AFM separately in the paper.     

Influence of the surface treatment of PEDOT:PSS layer with high boiling point solvent on the performance of inverted planar perovskite solar cells

Since perovskite precursor solution is typically prepared from high boiling point solvents, understanding the effect of high boiling point solvent treatment of the PEDOT:PSS layer on the performance of perovskite solar cells is important for device processing optimization. In this paper, influence of the surface treatment of the PEDOT:PSS layer with high boiling point solvent, including N,N-dimethylformamide (DMF), dimethyl sulfoxide (DMSO), and ethylene glycol (EG), on the device performance of the perovskite solar cells was investigated. Increased conductivity was measured for the PEDOT:PSS film after solvent treatments, which was ascribed to the partial removal of PSS component from the PEDOT:PSS layer, as evidenced by the UV–vis absorption spectroscopy and XPS spectroscopy. In comparison with the reference cell, poorer device performance was obtained for the perovskite solar cells directly deposited on the solvent washed PEDOT:PSS film, which was ascribed to the increased pin hole density of the perovskite films. However, insertion of a thin PSSNa layer between the PEDOT:PSS layer and the perovskite layer greatly improved device performance, demonstrating that PSS-rich surface is favorite for the crystal growth of the perovskite film. Increased external quantum efficiency over 600–750 nm was measured for the cells based on solvent treated PEDOT:PSS layer, leading to a short circuit current and the consequent performance enhancement.     

Explaining the effects of processing on the electrical properties of PEDOT:PSS

By simultaneously measuring the Seebeck coefficient and the conductivity in differently processed PEDOT:PSS films, fundamental understanding is gained on how commonly used processing methods improve the conductivity of PEDOT:PSS. Use of a high boiling solvent (HBS) enhances the conductivity by 3 orders of magnitude, as is well-known. Simultaneously, the Seebeck coefficient S remains largely unaffected, which is shown to imply that the conductivity is improved by enhanced connectivity between PEDOT-rich filaments within the film, rather than by improved conductivity of the separate PEDOT filaments. Post-treatment of PEDOT:PSS films by washing with H₂SO₄ leads to a similarly enhanced conductivity and a significant reduction in the layer thickness. This reduction strikingly corresponds to the initial PSS ratio in the PEDOT:PSS films, which suggests removal and replacement of PSS in PEDOT:PSS by HSO₄⁻ or SO₄²⁻ after washing. Like for the HBS treatment, this improves the connectivity between PEDOT filaments. Depending on whether the H₂SO₄ treatment is or is not preceded by an HBS treatment also the intra-filament transport is affected. We show that by characterization of S and σ it is possible to obtain more fundamental understanding of the effects of processing on the (thermo)electrical characteristics of PEDOT:PSS.     

ITO-free organic solar cells using highly conductive phenol-treated PEDOT:PSS anodes

Phenol as one of the most polar solvent was used to enhance the conductivity of poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) films. The conductivity of PEDOT:PSS films improved to 1193 S/cm after treatment with phenol vapor and 1054 S/cm after treatment with phenol drop. The treated films also showed high transmittance in the visible region which is one of the crucial factors for optoelectronic devices such as organic solar cells and light emitting diodes. The mechanism of conductivity enhancement of treated thin PEDOT:PSS films was investigated by atomic force microscopy (AFM) and UV/Vis spectrophotometer. The AFM images showed that the ratio of PEDOT to PSS at top most of the surface was increased for treated film. Rearrangement of PEDOT segment throughout the film and hence conformational changes are the reasons for enhancement of conductivity. The modified PEDOT:PSS films were used as electrode for ITO-free organic solar cells (OSCs). These ITO-free OSCs showed almost equal operation to those for ITO electrodes.     

The Curious Out‐of‐Plane Conductivity of PEDOT:PSS

For its application as transparent conductor in light‐emitting diodes and photovoltaic cells, both the in‐plane and out‐of‐plane conductivity of PEDOT:PSS are important. However, studies into the conductivity of PEDOT:PSS rarely address the out‐of‐plane conductivity and those that do, report widely varying results. Here a systematic study of the out‐of‐plane charge transport in thin films of PEDOT:PSS with varying PSS content is presented. To this end, the PEDOT:PSS is enclosed in small interconnects between metallic contacts. An unexpected, but strong dependence of the conductivity on interconnect diameter is observed for PEDOT:PSS formulations without high boiling solvent. The change in conductivity correlates with a diameter dependent change in PEDOT:PSS layer thickness. It is suggested that the order of magnitude variation in out‐of‐plane conductivity with only a 3‐4‐fold layer thickness variation can quantitatively be explained on basis of a percolating cluster model.     

Boosting Performance of Non‐Fullerene Organic Solar Cells by 2D g‐C3N4 Doped PEDOT:PSS

The power‐conversion efficiency (PCE) of single‐junction organic solar cells (OSCs) has exceeded 16% thanks to the development of non‐fullerene acceptor materials and morphological optimization of active layer. In addition, interfacial engineering always plays a crucial role in further improving the performance of OSCs based on a well‐established active‐layer system. Doping of graphitic carbon nitride (g‐C₃N₄) into poly(3,4‐ethylene‐dioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) as a hole transport layer (HTL) for PM6:Y6‐based OSCs is reported, boosting the PCE to almost 16.4%. After being added into the PEDOT:PSS, the g‐C₃N₄ as a Bronsted base can be protonated, weakening the shield effect of insulating PSS on conductive PEDOT, which enables exposures of more PEDOT chains on the surface of PEDOT:PSS core‐shell structure, and thus increasing the conductivity. Therefore, at the interface between g‐C₃N₄ doped HTL and PM6:Y6 layer, the charge transport is improved and the charge recombination is suppressed, leading to the increases of fill factor and short‐circuit current density of devices. This work demonstrates that doping g‐C₃N₄ into PEDOT:PSS is an efficient strategy to increase the conductivity of HTL, resulting in higher OSC performance.     

High efficiency arrays of polymer solar cells fabricated by spray‐coating in air

We present bulk heterojunction organic solar cells fabricated by spray‐casting both the PEDOT:PSS hole‐transport layer (HTL) and active PBDTTT‐EFT:PC₇₁BM layers in air. Devices were fabricated in a (6 × 6) array across a large‐area substrate (25 cm²) with each pixel having an active area of 6.45 mm². We show that the film uniformity and operational homogeneity of the devices are excellent. The champion device with spray cast active layer on spin cast PEDOT:PSS had an power conversion efficiency (PCE) of 8.75%, and the best device with spray cast active layer and PEDOT:PSS had a PCE of 8.06%. The impacts of air and light exposure of the active layer on device performance are investigated and found to be detrimental. Copyright © 2015 John Wiley & Sons, Ltd.     

Metal salt modified PEDOT:PSS as anode buffer layer and its effect on power conversion efficiency of organic solar cells

The effects of metal chlorides such as LiCl, NaCl, CdCl₂ and CuCl₂ on optical transmittance, electrical conductivity as well as morphology of PEDOT:PSS films have been investigated. Transmittance spectra of spun PEDOT:PSS layers were improved by more than 6% to a maximum of 94% in LiCl doped PEDOT:PSS film. The surface of the PEDOT:PSS films has exhibited higher roughness associated with an increase in the electrical conductivity after doping with metal salts. The improvement in the physical properties of PEDOT:PSS as the hole transport layer proved to be key factors towards enhancing the P3HT:PCBM bulk heterojunction (BHJ) solar cells. These improvements include significantly improved power conversion efficiency with values as high as 6.82% associated with high fill factor (61%) and larger short circuit current density (∼18 mA cm⁻²).     

Aging process of PEDOT:PSS dispersion and robust recovery of aged PEDOT:PSS as a hole transport layer for organic solar cells

Conducting p-type polymer of poly(3,4-ethylene dioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) has been widely used for organic optoelectronics, particularly as a hole transport layer for organic solar cells. While the aged PEDOT:PSS dispersion impacts device performance, the aging of PEDOT:PSS dispersion have not been well investigated. Moreover, the recovery process of aged (two-year-old) PEDOT:PSS dispersion has not been demonstrated yet. Herein, it is found that aqueous PEDOT:PSS dispersion undergoes extensive phase separation during the aging process, resulting in both nanoscale and macroscale hydrophobic PEDOT-rich agglomerates. When the aged PEDOT:PSS thin film is integrated into P3HT:PCBM organic solar cells, the PEDOT-rich agglomerates trap the photogenerated holes at the PEDOT:PSS/P3HT interface, resulting in poor extraction efficiency in organic solar cells. To recover a hole transport functionality from aged PEDOT:PSS, three different solvents such as isopropyl alcohol (C₃H₇OH), ethanol (C₂H₅OH) and methanol (CH₃OH) are investigated. Among them, it is found that isopropyl alcohol (IPA) yielded very uniform PEDOT:PSS thin film layer. This is because hydrophobic functional groups of IPA solvent facilitated the preferential solvation of phase separated hydrophobic PEDOT-rich agglomerates. However, when non-optimal concentration of IPA solvents was added into the aged PEDOT:PSS dispersion, the size of PEDOT-rich agglomerates was adversely enlarged. When organic solar cells were fabricated using more than a two-year-old PEDOT:PSS that was treated with IPA solvent, the resulting device performance of organic solar cells was fully recovered and became comparable or better than that of organic solar cells fabricated with fresh PEDOT:PSS.     

Effect of high voltage electric field on structure and property of PEDOT:PSS film

Low electrical conductivity of PEDOT:PSS film is to some extent a limit for its wide application. To solve this problem, the high voltage electric field was used to improve the film’s electrical conductivity and its effects on the film’s structure and properties were investigated. The PEDOT:PSS film was prepared on quartz substrate with spin coating. Visible light transmittance of the prepared film was tested with UV–Visible spectroscopy and chemical structure was measured with Fourier transform Raman spectroscopy (FIRM). The surface morphology was characterized with AFM, and electrical conductivity was measured with Hall effects measurement. The results showed that with the increase of the electric field, the electrical conductivity of PEDOT:PSS film was boosted rapidly at first, and then improved slowly when the electric field was above 200 kV/m. The film’s electrical conductivity improved more than 17 times in total from 0.51 × 10^–3 up to 8.92 × 10^–3 S/m. However, the film’s visible light transmittance decreased only a little with the increase of the electric field, not more than 3%. In addition, despite little change in the chemical structure of the PEDOT:PSS film, its surface roughness increased significantly with the increase of the electric field intensity.     

Directional dependence of electron blocking in PEDOT:PSS

The directional dependence of electron blocking by poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) is investigated in organic photovoltaic devices. In a conventional OPV architecture we find that a doped interlayer forms between poly(3-hexylthiophene) (P3HT) and the PSS-rich top layer of spin-coated PEDOT:PSS films. In an inverted OPV architecture, we find no mixing between PEDOT:PSS and P3HT, which is due to the lower concentration of PSS in bulk PEDOT:PSS than is found in the PSS-rich top layer. Through electrical measurements of conventional and inverted photovoltaic devices we show that the interlayer is necessary for PEDOT:PSS to be electron blocking. This result implies that PEDOT:PSS is not intrinsically electron blocking and that its directional anisotropy must be considered when comparing the advantages and disadvantages of conventional and inverted architecture photovoltaic devices.     

A highly conductive PEDOT:PSS film with the dipping treatment by hydroiodic acid as anode for organic light emitting diode

A highly conductive, transparent and uniform poly (3,4-ethylenedioxythiophene):poly (styrenesulfonate) (PEDOT:PSS) film has been developed by dipping treatment with hydriodic acid (HI) solution. The HI-treated PEDOT:PSS film can reach a sheet resistance of 68 Ω per square and a transmittance of 87% at 550 nm. The conductivity enhancement for the HI-treated film is ascribed to the permeation of proton and iodine anion of HI into PEDOT:PSS film, resulting in the separation of PSS and PEDOT chains. The phase separation of PSS and PEDOT can provide more conductive pathways for carriers to improve conductivity of the film. Using the optimized HI-treated PEDOT:PSS film as anode, we have fabricated indium tin oxide (ITO)-free organic light emitting diode (OLED), which shows better performance than the device with ITO as anode. This proves that such PEDOT:PSS film with the dipping treatment by HI solution is a promising alternative to ITO for low cost, transparent and flexible OLED application.     

Effects of tetramethylene sulfone solvent additives on conductivity of PEDOT:PSS film and performance of polymer photovoltaic cells

A solvent additive in PEDOT:PSS solution is one of many methods to improve the conductivity of the poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) films. We explore a new type of the solvent additive, namely tetramethylene sulfone (TMS), for the fabrication of the PEDOT:PSS conductive layer in the ITO/PEDOT:PSS/P3HT:PCBM/TiO_x/Al polymer photovoltaic cells, in comparison to a more common dimethyl sulfoxide (DMSO) solvent additive. At optimal conditions, the TMS additive at 10 wt.% has been found to enhance the conductivity of pristine PEDOT:PSS films from 0.04 S/cm up to approximately 189 S/cm, compared with the highest conductivity for the case of the DMSO additive at 15 wt.% of 117 S/cm. Possible mechanisms of this conductivity enhancement, relating to the polymer conformation and the film morphology, have been investigated by Raman spectroscopy, X-ray diffraction, atomic force microscopy, and transmission electron microscopy. The performance of the polymer photovoltaic cells fabricated with the solvent additives PEDOT:PSS films follows a similar trend to the conductivity of the films as a function of the additive concentration. The additives mainly lead to greater short circuit current density (J_sc) of the photovoltaic cells. The highest power conversion efficiency (PCE) of 2.24% of the device has been obtained with the 10 wt.% TMS additive of, compared to the PCE of 1.48% for the standard device without solvent additive.     

In‐Situ Switching from Barrier‐Limited to Ohmic Anodes for Efficient Organic Optoelectronics

Injection and extraction of charges through ohmic contacts are required for efficient operation of semiconductor devices. Treatment using polar non‐solvents switches polar anode surfaces, including PEDOT:PSS and ITO, from barrier‐limited hole injection and extraction to ohmic behaviour. This is caused by an in‐situ modification of the anode surface that is buried under a layer of organic semiconductor. The exposure to methanol removes polar hydroxyl groups from the buried anode interface, and permanently increases the work function by 0.2–0.3 eV. In the case of ITO/PEDOT:PSS/PBDTTT‐CT:PC71BM/Al photovoltaic devices, the higher work function promotes charge transfer, leading to p‐doping of the organic semiconductor at the interface. This results in a two‐fold increase in hole extraction rates which raises both the fill factor and the open‐circuit voltage, leading to high power conversion efficiency of 7.4%. In ITO/PEDOT:PSS/F8BT/Al polymer light‐emitting diodes, where the organic semiconductor's HOMO level lies deeper than the anode Fermi level, the increased work function enhances hole injection efficiency and luminance intensity by 3 orders of magnitude. In particular, hole injection rates from PEDOT:PSS anodes are equivalent to those achievable using MoO₃. These findings exemplify the importance of work function control as a tool for improved electrode design, and open new routes to device interfacial optimization using facile solvent processing techniques. Such simple, persistent, treatments pave the way towards low cost manufacturing of efficient organic optoelectronic devices.     

Poly(3,4-ethylenedioxythiophene):polystyrene sulfonate films with low conductivity and low acidity through a treatment of their solutions with probe ultrasonication and their application as hole transport layer in polymer solar cells and perovskite solar cells

Poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS) has been widely used as the hole transport material in optoelectronic devices. To avoid the cross talk among different crossbars, PEDOT:PSS with low conductivity is required. It thus has a high loading of the non-conductive PSSH. The PSSH-to-PEDOT weight ratio is 6 for Clevios P VP Al 4083 that is the most popular polymer as the hole transport layer. However, the acidic PSSH brings severe problems to the device stability and performance. Here, PEDOT:PSS solutions with low acidity can be prepared through a facile treatment of PEDOT:PSS solution by probe ultrasonication. Two grades of PEDOT:PSS, Clevios PH1000 and Clevios P, with a PSSH-to-PEDOT weight ratio of 2.5 were treated by probe ultrasonication. The ultrasonication can lower the viscosity and the colloidal sizes of PEDOT:PSS solutions and conductivity of PEDOT:PSS films. The pH value of probe-ultrasonicated Clevios P was 2.12, higher than that (1.77) of pristine Clevios P VP Al 4083. The ultrasonication-treated PEDOT:PSS solutions were used as hole transport layer in polymer solar cells and perovskite solar cells. The photovoltaic performances of these solar cells are comparable to that of control devices employing Clevios P VP Al 4083 PEDOT:PSS as the hole transport layer.