The dual localized surface plasmonic effects of gold nanodots and gold nanoparticles enhance the performance of bulk heterojunction polymer solar cells

In this study, we investigated the effects of plasmonic resonances induced by gold nanodots (Au NDs), thermally deposited on the active layer, and octahedral gold nanoparticles (Au NPs), incorporated within the hole transport layer, on the performance of bulk heterojunction polymer solar cells (PSCs) based on poly(3-hexyl thiophene) (P3HT) and [6,6]-phenyl-C₆₁butyric acid methyl ester (PC₆₁BM). Thermal deposition of 5.3-nm Au NDs between the active layer and the cathode in a P3HT:PC₆₁BM device resulted in the power conversion efficiency (PCE) of 4.6%—that is 15% greater than that (4.0%) for the P3HT:PC₆₁BM device without Au NDs. The Au NDs provided near-field enhancement through excitation of the localized surface plasmon resonance (LSPR), thereby enhancing the degree of light absorption.     

Solution processed bulk heterojunction polymer solar cells with low band gap DPP-CN small molecule sensitizer

The improvement of near infrared wavelength sensitivity in the bulk heterojunction organic polymer solar cell based on poly (3-hexylthiophene) (P3HT) and PC₇₀BM, by the addition of soluble DPP-CN small molecule is reported. By incorporating DPP-CN, the photosensitivity in the longer wavelength region was improved and the power conversion efficiency (PCE) has been reached to 4.37% as compared to 3.23% for the device based on P3HT:PC₇₀BM blend. The increase in the PCE is attributed to the increase in light harvesting property of the blend and efficient dissociation of excitons into free charge carriers due to the increased number of D–A sites. The PCE has been further enhanced to 4.70%, when mixed solvent cast P3HT:DPP-CN:PC₇₀BM blend is used as photoactive layer. The optical absorption spectra of the blend showed that the blend film cast from mixed solvent broadened the absorption wavelength range. This occurred as result of a large red shift of P3HT absorption peak and same time a widening and small red shift of DPP-CN absorption peak in the blend film. The improved light harvesting property of thermally annealed film is considered to the factor responsible for the improvement in the PCE.     

Improving performance of polymer solar cells based on PSBTBT/PC71BM via controlled solvent vapor annealing

Controlled solvent vapor annealing (C-SVA) is a powerful tool to control the morphology for high performance polymer solar cells (PSCs). In this work, the PSCs employed a blend of poly[(4,4′-bis(2-ethylhexyl)dithieno[3,2-b:2′,3′-d]silole)-2,6-diyl-alt-(2,1,3-benzothiadiazole)-4,7-diyl] (PSBTBT) and [6,6]-phenyl-C71-butyric acid methyl ester (PC₇₁BM) is used to show this case. The solar cells upon C-SVA give Power Conversion Efficiency (PCE) of 5.40%, in contrast to 4.14% for the pristine and 4.70% for the thermally annealed devices. The increased PSBTBT concentration on the bottom surface of the C-SVA treated film favors charge carriers transportation to the anode, which contributes to the increased hole mobility of the photoactive layer and thus the device performance.     

Synthesis of a Modified PC70BM and Its Application as an Electron Acceptor with Poly(3‐hexylthiophene) as an Electron Donor for Efficient Bulk Heterojunction Solar Cells

A simple and effective modification of phenyl‐C₇₀‐butyric acid methyl ester (PC₇₀BM) is carried out in a single step after which the material is used as electron acceptor for bulk heterojunction polymer solar cells (PSCs). The modified PC₇₀BM, namely CN‐PC₇₀BM, showed broader and stronger absorption in the visible region (350–550 nm) of the solar spectrum than PC₇₀BM because of the presence of a cyanovinylene 4‐nitrophenyl segment. The lowest unoccupied molecular energy level (LUMO) of CN‐PC₇₀BM is higher than that of PC₇₀BM by 0.15 eV. The PSC based on the blend (cast from tetrahydrofuran (THF) solution) consists of P3HT as the electron donor and CN‐PC₇₀BM as the electron acceptor and shows a power conversion efficiency (PCE) of 4.88%, which is higher than that of devices based on PC₇₀BM as the electron acceptor (3.23%). The higher PCE of the solar cell based on P3HT:CN‐PC₇₀BM is related to the increase in both the short circuit current (J_sc) and the open circuit voltage (V_oc). The increase in J_sc is related to the stronger light absorption of CN‐PC₇₀BM in the visible region of the solar spectrum as compared to that of PC₇₀BM. In other words, more excitons are generated in the bulk heterojunction (BHJ) active layer. On the other hand, the higher difference between the LUMO of CN‐PC₇₀BM and the HOMO of P3HT causes an enhancement in the V_oc. The addition of 2% (v/v) 1‐chloronapthalene (CN) to the THF solvent during film deposition results in an overall improvement of the PCE up to 5.83%. This improvement in PCE can be attributed to the enhanced crystallinity of the blend (particularly of P3HT) and more balanced charge transport in the device.     

A plasmonically enhanced polymer solar cell with gold–silica core–shell nanorods

We report the use of chemically synthesized gold (Au)–silica core–shell nanorods with the length of 92.5 ± 8.0 nm and diameter of 34.3 ± 4.0 nm for the efficiency enhancement of bulk heterojunction (BHJ) polymer solar cells. Silica coated Au nanorods were randomly blended into the BHJ layers of these solar cells. This architecture inhibits the carrier recombination at the metal/polymer interface and effectively exploits light absorption at the surface plasmon resonance wavelengths of the Au–silica nanorods. To match the two plasmon resonant peaks of the Au–silica nanorods, we employed a low bandgap polymer, poly[2,6-(4,4-bis-(2-ethylhexyl)-4H-cyclopenta[2,1-b;3,4-b′] dithiophene)-alt-4,7-(2,1,3-benzothiadiazole)] (PCPDTBT) to construct a solar cell. The absorption spectrum of PCPDTBT:[6,6]-phenyl-C₇₁-butyric acid methyl ester (PC₇₀BM) is relatively wide and matches the two plasmon resonance peaks of Au–silica nanorods, which leads to greater plasmonic effects. We also constructed the poly(3-hexylthiophene):[6,6]-phenyl-C₆₁-butyric acid methyl ester (P3HT:PC₆₀BM) cells for comparison. The absorption spectrum of P3HT:PC₆₀BM only overlaps one of the plasmon resonance peak of Au–silica nanorods. The efficiency of the P3HT:PC₆₀BM device incorporating optimized Au–silica nanorods is enhanced by 12.9% from 3.17% to 3.58%, which is due to the enhanced light absorption. Compared with the P3HT:PC₆₀BM device with Au–silica nanorods, the PCPDTBT:PC₇₀BM device with 1 wt% Au–silica nanorods concentration has a higher efficiency of 4.4% with an increase of 26%.     

Broad-band plasmonic Cu-Au bimetallic nanoparticles for organic bulk heterojunction solar cells

In this work, a facile preparation of Cu-Au bimetallic nanoparticles (NPs) with core-shell nanostructures is reported. Importantly, as-prepared Cu-Au NPs are highly stable, solution-processable and exhibit a broad localized surface plasmon resonance (LSPR) band at long wavelengths of 550–850 nm. Highly efficient plasmonic organic solar cells (OSCs) were fabricated by embedding Cu-Au NPs in an anodic poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) layer. The average power conversion efficiency (PCE) was enhanced from 3.21% to 3.63% for poly(3-hexylthiophene) (P3HT):phenyl-C₆₁-butyric acid methyl ester (PC₆₁BM) based devices, from 6.51% to 7.13% for poly[(ethylhexyl-thiophenyl)-benzodithiophene -(ethylhexyl)-thienothiophene](PTB7-th):PC₆₁BM based devices and from 7.53% to 8.48% for PTB7-th:PC₇₁BM based devices, corresponding to 9.5–13.4% PCE improvement. Such an improvement is very comparable to that (12.5%) obtained in those with plasmonic Au NPs but achieved at lower cost. This study thus demonstrates a novel and cost-effective approach to enhance the photovoltaic performance of OSCs, in combination with the broad-band plasmonic Cu-Au bimetallic nanostructures.     

Self‐Doping Fullerene Electrolyte‐Based Electron Transport Layer for All‐Room‐Temperature‐Processed High‐Performance Flexible Polymer Solar Cells

To achieve high‐performance large‐area flexible polymer solar cells (PSCs), one of the challenges is to develop new interface materials that possess a thermal‐annealing‐free process and thickness‐insensitive photovoltaic properties. Here, an n‐type self‐doping fullerene electrolyte, named PCBB‐3N‐3I, is developed as electron transporting layer (ETL) for the application in PSCs. PCBB‐3N‐3I ETL can be processed at room temperature, and shows excellent orthogonal solvent processability, substantially improved conductivity, and appropriate energy levels. PCBB‐3N‐3I ETL also functions as light‐harvesting acceptor in a bilayer solar cell, contributing to the overall device performance. As a result, the PCBB‐3N‐3I ETL‐based inverted PSCs with a PTB7‐Th:PC₇₁BM photoactive layer demonstrate an enhanced power conversion efficiency (PCE) of 10.62% for rigid and 10.04% for flexible devices. Moreover, the device avoids a thermal annealing process and the photovoltaic properties are insensitive to the thickness of PCBB‐3N‐3I ETL, yielding a PCE of 9.32% for the device with thick PCBB‐3N‐3I ETL (61 nm). To the best of one's knowledge, the above performance yields the highest efficiencies for the flexible PSCs and thick ETL‐based PSCs reported so far. Importantly, the flexible PSCs with PCBB‐3N‐3I ETL also show robust bending durability that could pave the way for the future development of high‐performance flexible solar cells.     

Efficient ternary blend polymer solar cells with a bipolar diketopyrrolopyrrole small molecule as cascade material

We present a ternary strategy to enhance the power conversion efficiency (PCE) of bulk heterojunction polymer solar cells (PSCs) with a bipolar small molecule as cascade material. A bipolar diketopyrrolopyrrole small molecule (F(DPP)₂B₂), as the second electron acceptor, was incorporated into poly(3-hexylthiophene) (P3HT): [6,6]-phenyl-C₆₁-butyric-acidmethyl-ester (PC₆₁BM) blend to fabricate ternary blend PSCs. The introduction of the bipolar compound F(DPP)₂B₂ can not only broaden the light absorption of the active layer because of its absorption in near infrared region but also play a bridging role between P3HT and PC₆₁BM due to the cascaded energy level structure, thus improving the charge separation and transportation. The optimized ternary PSC with 5 wt% F(DPP)₂B₂ content delivered a high PCE of 3.92% with a short-circuit current density (J_sc) of 9.63 mA cm⁻², an open-circuit voltage (V_oc) of 0.62 V and a fill factor (FF) of 64.90%, showing an 23% improvement of PCE as compared to the binary systems based on P3HT:PC₆₁BM (3.18%) or P3HT:F(DPP)₂B₂ (3.17%). The results indicate that the ternary PSCs with a bipolar compound have the potential to surpass high-performance binary PSCs after carefully device optimization.     

Incorporating Graphitic Carbon Nitride (g‐C3N4) Quantum Dots into Bulk‐Heterojunction Polymer Solar Cells Leads to Efficiency Enhancement

Graphitic carbon nitride (g‐C₃N₄) has been commonly used as photocatalyst with promising applications in visible‐light photocatalytic water‐splitting. Rare studies are reported in applying g‐C₃N₄ in polymer solar cells. Here g‐C₃N₄ is applied in bulk heterojunction (BHJ) polymer solar cells (PSCs) for the first time by doping solution‐processable g‐C₃N₄ quantum dots (C₃N₄ QDs) in the active layer, leading to a dramatic efficiency enhancement. Upon C₃N₄ QDs doping, power conversion efficiencies (PCEs) of the inverted BHJ‐PSC devices based on different active layers including poly(3‐hexylthiophene‐2,5‐diyl):[6,6]‐phenyl‐C61‐butyric acid methyl ester (P3HT:PC₆₁BM), poly(4,8‐bis‐alkyloxybenzo(l,2‐b:4,5‐b′)dithiophene‐2,6‐diylalt‐(alkyl thieno(3,4‐b)thiophene‐2‐carboxylate)‐2,6‐diyl):[6,6]‐phenyl C₇₁‐butyric acid methyl ester (PBDTTT‐C:PC₇₁BM), and poly[4,8‐bis(5‐(2‐ethylhexyl)thiophen‐2‐yl)benzo[1,2‐b:4,5‐b′]dithiophene‐co‐3‐fluorothieno [3,4‐b]thiophene‐2‐carboxylate] (PTB7‐Th):PC₇₁BM reach 4.23%, 6.36%, and 9.18%, which are enhanced by ≈17.5%, 11.6%, and 11.8%, respectively, compared to that of the reference (undoped) devices. The PCE enhancement of the C₃N₄ QDs doped BHJ‐PSC device is found to be primarily attributed to the increase of short‐circuit current (J_sc), and this is confirmed by external quantum efficiency (EQE) measurements. The effects of C₃N₄ QDs on the surface morphology, optical absorption and photoluminescence (PL) properties of the active layer film as well as the charge transport property of the device are investigated, revealing that the efficiency enhancement of the BHJ‐PSC devices upon C₃N₄ QDs doping is due to the conjunct effects including the improved interfacial contact between the active layer and the hole transport layer due to the increase of the roughness of the active layer film, the facilitated photoinduced electron transfer from the conducting polymer donor to fullerene acceptor, the improved conductivity of the active layer, and the improved charge (hole and electron) transport.     

Fluorine functionalized asymmetric indo [2,3-b]quinoxaline framework based D-A copolymer for fullerene polymer solar cells

Innovating molecular structure of copolymer donor materials is still one of the prominent approach to obtain high-performance polymer solar cells (PSCs). In this paper, two novel wide bandgap (WBG) copolymers, namely PBDTTS-IQ and PBDTTS-DFIQ, based on asymmetric planar aromatic core indo [( Li et al., 2012; Wang et al., 2020) 2,32,3-b]quinoxaline (IQ) as acceptor unit through tuning side chains with fluorine (F) atom engineering and exemplary alkylthio-thienyl substituted benzodithiophene (BDTTS) donor group, are synthesized and finally employed as the photovoltaic donor materials for fullerene polymer solar cells (PSCs). After blending with PC₇₁BM acceptor, the PBDTTS-DFIQ:PC₇₁BM blend film presented better efficient exciton dissociation and charge extraction, more balanced electron/hole mobility (μ_h/μ_e), and nice morphology in comparison with PBDTTS-IQ:PC₇₁BM blend film. Encouragingly, the PBDTTS-DFIQ:PC₇₁BM based PSCs exhibits a higher power conversion efficiency (PCE) of 7.4% than that of the device based on the PBDTTS-IQ:PC₇₁BM blend with a PCE of 4.96%, which thanks to an enhancement of open-circuit voltage (V_oc) of 0.84 V, short current density (J_sc) of 13.26 mA cm⁻² and fill factor (FF) of 66.00% simultaneously. These results demonstrate that this asymmetric IQ framework is a wonderful acceptor moiety to build light-harvesting copolymers for highly efficient PSCs.     

High‐Yield Synthesis and Electrochemical and Photovoltaic Properties of Indene‐C70 Bisadduct

[6, 6]‐Phenyl‐C₆₁‐butyric acid methyl ester (PC₆₀BM) is the widely used acceptor material in polymer solar cells (PSCs). Nevertheless, the low LUMO energy level and weak absorption in visible region are its two weak points. For enhancing the solar light harvest, the soluble C₇₀ derivative PC₇₀BM has been used as acceptor instead of PC₆₀BM in high efficiency PSCs in recent years. But, the LUMO level of PC₇₀BM is the same as that of PC₆₀BM, which is too low for the PSCs based on the polymer donors with higher HOMO level, such as poly (3‐hexylthiophene) (P3HT). Here, a new soluble C₇₀ derivative, indene‐C₇₀ bisadduct (IC₇₀BA), is synthesized with high yield of 58% by a one‐pot reaction of indene and C₇₀ at 180 °C for 72 h. The electrochemical properties and electronic energy levels of the fullerene derivatives are measured by cyclic voltammetry. The LUMO energy level of IC₇₀BA is 0.19 eV higher than that of PC₇₀BM. The PSC based on P3HT with IC₇₀BA as acceptor shows a higher V_oc of 0.84 V and higher power conversion efficiency (PCE) of 5.64%, while the PSC based on P3HT/PC₆₀BM and P3HT/PC₇₀BM displays V_oc of 0.59 V and 0.58 V, and PCE of 3.55% and 3.96%, respectively, under the illumination of AM1.5G, 100 mW cm^?2. The results indicate that IC₇₀BA is an excellent acceptor for the P3HT‐based PSCs and could be a promising new acceptor instead of PC₇₀BM for the high performance PSCs based on narrow bandgap conjugated polymer donor.     

Enhanced performance in inverted polymer solar cells employing microwave-annealed sol-gel ZnO as electron transport layers

In this work, we propose a facile microwave-assisted approach for annealing sol-gel derived ZnO films to serve as electron transport layers (ETLs) for inverted bulk heterojunction polymer solar cells. We have demonstrated an impressive enhancement in performance for devices based on a poly (3-hexylthiophene) (P3HT): (6,6)-phenyl-C₆₁-butyric acid methyl ester (PC₆₁BM) system employing the microwave-annealed ZnO (ZnO (MW)) ETLs in comparison to the cases using the conventional hotplate-annealed ZnO (ZnO (HP)) ones. The better electron transport in the device with the ZnO (MW) ETL is mainly ascribed to the preferable interfacial contact as evidenced by the morphology characteristics. Furthermore, the comprehensive analyses conducted from the light intensity dependent photocurrent and photovoltage measurements, the capacitance-voltage characteristics, and the alternating current impedance spectra suggest that the utilization of the ZnO (MW) ETLs can effectively suppress trap-assisted recombination as well as charge accumulation at the interface between P3HT: PC₆₁BM layers and ZnO layers, which is responsible for the enhanced device performance.     

Effect of blend layer thickness on the dielectric response of PCDTBT:PC71BM-based bulk heterojunction solar cells

Bulk heterojunction solar cells based on a blend of poly[N-9′-heptadecanyl-2,7-carbazole-alt-5,5-(4′,7′-di-2-thienyl-2′,1′,3′-benzothiadiazole)] (PCDTBT) and [6,6]-phenyl-C71-butyric acid methyl ester (PC₇₁BM), were studied. The organic photoactive layers were spin coated onto a poly(3,4-ethylenedioxythiophene)/poly(4-styrenesulfonate) (PEDOT-PSS) interfacial layer at speeds of 600 and 2000 rpm. The molecular structure of PCDTBT, PC₇₁BM, and the PCDTBT:PC₇₁BM blend was investigated using Fourier-transform IR (FTIR) spectroscopy, which confirmed the absence of interactions between the individual components of the composite. The dielectric properties of PCDTBT:PC₇₁BM-based solar cells were studied under illumination by means of impedance analysis. The dielectric constant, impedance, and ac conductance were analyzed as a function of frequency at different bias voltages close to the open circuit voltage (Voc). We found that the dielectric constant, dielectric loss, and conductance increased with increasing PCDTBT:PC₇₁BM thickness. Impedance spectroscopy analysis revealed decreases in charge recombination and the resistance of the whole device with increasing spin coating speed for the active layer. Moreover, an increase in recombination resistance for the solar cells was observed close to V_OC.     

Influence of molar mass ratio,annealing temperature and cathode buffer layer on power conversion efficiency of P3HT:PC71BM based organic bulk heterojunction solar cell

In bulk heterojunction (BHJ) solar cells, the molar mass ratio of donor-acceptor polymers, the annealing temperature (T_an) and the cathode buffer layer plays very consequential role in improving the power conversion efficiency (PCE) by tuning the film morphology and enhancing the charge carrier dynamics. A comprehensive understanding of each of these factors is essential in order to optimize the performance of organic solar cells (OSCs). Albeit there are several fundamental reports regarding these factors, an altogether meticulous correlation of these physical processes with experimental evidence of the photo active layer are required. In this work, we systematically analyzed the influence of different molar mass ratio, the annealing temperature (T_an) and the cathode buffer layer of rrP3HT:PC₇₁BM based BHJ solar cells and their corresponding photovoltaic performances were correlated carefully with their thin film growth structure and energy level diagram. The device having 1:0.8 molar mass ratio of rrP3HT:PC₇₁BM and T_an = 150 °C annealing temperature with Bathocuproine (BCP) as the cathode buffer layer having ITO/PEDOT:PSS/rrP3HT:PC₇₁BM (molar mass ratio = 1:0.8; (T_an = 150 °C)/BCP/Al) configuration showed the best device performance with PCE, ɳ = 4.79%, Jsc = 14.21 mA/cm², V_oc = 0.58 V and FF = 57.8%. This drastic variation in PCE of the device having BCP/Al as the cathode contact compared to the other device configurations is due to the coalesced effects of better hole-blocking capacity of BCP along with Al and better phase separation of the active blend layer at 150 °C annealing temperature. These results explicate the cumulate role of all these physical parameters and their combined contribution to the PCE amendment and overall device performance with rrP3HT:PC₇₁BM based organic BHJ solar cell.     

High performance thermal-treatment-free tandem polymer solar cells with high fill factors

It is an effective way to enhance device performance of polymer solar cells (PSCs) by using a tandem structure that combines two or more solar cells. For tandem PSCs, the buffer layer plays an important role in determining the device performance. The most commonly used buffer layers, such as PEDOT:PSS, TiO_x, and ZnO, need thermal treatments that are not beneficial for reducing the fabrication complexity and cost of tandem PSCs. It is necessary to develop tandem PSCs fabricated by a thermal-treatment-free process. In this paper, we report high performance thermal-treatment-free tandem PSCs by developing PFN as buffer layers for both subcells. A power conversion efficiency (PCE) of 10.50% and a high fill factor of 72.44% were achieved by stacking two identical PTB7:PC₇₁BM subcells. When adopting a rear PTB7-Th:PC₇₁BM subcell, the highest PCE of 10.79% was further obtained for the tandem devices. The thermal-treatment-free process is especially applicable to flexible devices, in which plastic substrates are usually used.     

Solvent-resistant ITO work function tuning by an acridine derivative enables high performance inverted polymer solar cells

In order to avoid an interpenetration of the buffer and the photoactive layers during preparation of polymer solar cells (PSCs), solvent-resistant buffer films were chemically modified on indium tin oxide (ITO) surface. The conjugated aromatics acridine orange base (AOB) was introduced into the films using 3-bromopropyltrimethoxysilane (BrTMS) as coupling agent. Upon ITO surface modification, the respective work functions show a significant decrease. The modified ITO substrates were implemented in inverted PSCs based on PBDTTT-C-T:PC₇₁BM. With the modification, the power conversion efficiency (PCE) was improved significantly from 4.10% (for the inverted PSC without this buffer layer) to 7.56%. The PCE enhancement is mainly caused by the increase of the open-circuit voltage (43%). These results indicate that the solvent-resistant film is able to facilitate electron collection and transportation, thus providing a novel route to high efficient PSCs by surface engineering.     

A universal roll‐to‐roll slot‐die coating approach towards high‐efficiency organic photovoltaics

This work develops a combinational use of solvent additive and in‐line drying oven on the flexible organic photovoltaics to improve large‐area roll‐to‐roll (R2R) slot‐die coating process. Herein, addition of 1,8‐diiodooctane (DIO) in the photoactive layer is conducted to yield a performance of 3.05% based on the blending of poly(3‐hexylthiophene) (P3HT) and [6,6]‐phenyl C₆₁‐butyric acid methyl ester (PC₆₁BM), and a very promising device performance of 7.32% based on the blending of poly[[4,8‐bis[(2‐ethylhexyl)oxy] benzo[1,2‐b:4,5‐b’] dithiophene‐2,6‐diyl] [3‐fluoro‐2‐[(2‐ethylhexyl)carbonyl]thieno[3,4‐b]thiophenediyl]] (PTB7) and [6,6]‐phenyl C₇₁‐butyric acid methyl ester (PC₇₁BM). Based on this R2R slot‐die coating approach for various polymers, we demonstrate the high‐performance result with respect to the up‐scaling from small high‐PCE cell to large‐area module. This present study provides a route for fabricating a low‐cost, large‐area, and environmental‐friendly flexible organic photovoltaics.     

A low-cost and low-temperature processable zinc oxide-polyethylenimine (ZnO:PEI) nano-composite as cathode buffer layer for organic and perovskite solar cells

Nanocomposite buffer layer based on metal oxide and polymer is merging as a novel buffer layer for organic solar cells, which combines the high charge carrier mobility of metal oxide and good film formation properties of polymer. In this work, a nanocomposite of zinc oxide and a commercialized available polyethylenimine (PEI) was developed and used as the cathode buffer layer (CBL) for the inverted organic solar cells and p-i-n heterojunction perovskite solar cells. The cooperation of PEI in nano ZnO offers a good film forming ability of the composite material, which is an advantage in device fabrication. In addition, power conversion efficiency (PCE) of the ZnO:PEI CBL based device was also improved when compared to that of ZnO-only and PEI-only devices. The highest PCE of P3HT:PC₆₁BM and PTB7-Th:PC₆₁BM devices reached to 3.57% and 8.16%, respectively. More importantly, there is no obvious device performance loss with the increase of the layer thickness of ZnO:PEI CBL to 60 nm in organic solar cells, which is in contrast to the PEI based devices, whose device performance decreases dramatically when the PEI layer thickness is higher than 6 nm. Such a nano composite material is also applicable in inverted heterojunction perovskite solar cells. A PCE of 11.76% was achieved for the perovskite solar cell with a thick ZnO:PEI CBL (150 nm) CBL, which is around 1.71% higher than that of the reference cell without CBL, or with ZnO CBL. In addition, stability of the organic and perovskite solar cells having ZnO:PEI CBL was also found to be improved in comparison with that of PEI based device.     

Layer by layer characterisation of the degradation process in PCDTBT:PC71BM based normal architecture polymer solar cells

This work demonstrates the stability and degradation of OSCs based on poly[N-9′-heptadecanyl-2,7-carbazole-alt-5,5-(4′,7′-di-2-thienyl-2′,1′,3′ benzothiadiazole)] (PCDTBT): (6,6)-Phenyl C₇₁ butyric acid methyl ester (PC₇₁BM) photoactive blend layers as a function of ageing time in air. Analysis of the stability and degradation process for the OSCs was conducted under ambient air by using current-voltage (I-V) measurements and x-ray photoelectron spectroscopy (XPS). The interface between photoactive layer and HTL (PEDOT:PSS) was also investigated. Device stability was investigated by calculating decay in power conversion efficiency (PCE) as a function of ageing time in the air. The PCE of devices decrease from 5.17 to 3.61% in one week of fabrication, which is attributed to indium and oxygen migration into the PEDOT:PSS and PCDTBT:PC₇₁BM layer. Further, after aging for 1000 h, XPS spectra confirm the significant diffusion of oxygen into the HTL and photoactive layer which increased from 3.0 and 23.3% to 20.4 and 35.7% in photoactive layer and HTL, respectively. Similarly, the indium content reached to 17.9% on PEDOT:PSS surface and 0.4% on PCDTBT:PC₇₁BM surface in 1000 h. Core-level spectra of active layer indicate the oxidation of carbon atoms in the fullerene cage, oxidation of nitrogen present in the polymer matrix and formation of In₂O₃ due to indium diffusion. We also observed a steady fall in the optical absorption of the active layer during ageing in ambient air and it reduced to 76.5% of initial value in 1000 h. On the basis of these experimental results, we discussed key parameters that account for the degradation process and stability of OSCs in order to improve the device performance.     

Efficient Polymer Solar Cells Based on Poly(3‐hexylthiophene):Indene‐C70 Bisadduct with a MoO3 Buffer Layer

Polymer solar cells (PSCs) with poly(3‐hexylthiophene) (P3HT) as a donor, an indene‐C₇₀ bisadduct (IC₇₀BA) as an acceptor, a layer of indium tin oxide modified by MoO₃ as a positive electrode, and Ca/Al as a negative electrode are presented. The photovoltaic performance of the PSCs was optimized by controlling spin‐coating time (solvent annealing time) and thermal annealing, and the effect of the spin‐coating times on absorption spectra, X‐ray diffraction patterns, and transmission electron microscopy images of P3HT/IC₇₀BA blend films were systematically investigated. Optimized PSCs were obtained from P3HT/IC₇₀BA (1:1, w/w), which exhibited a high power conversion efficiency of 6.68%. The excellent performance of the PSCs is attributed to the higher crystallinity of P3HT and better a donor–acceptor interpenetrating network of the active layer prepared under the optimized conditions. In addition, PSCs with a poly(3,4‐ethylenedioxy‐thiophene):poly(styrenesulfonate) (PEDOT:PSS) buffer layer under the same optimized conditions showed a PCE of 6.20%. The results indicate that the MoO₃ buffer layer in the PSCs based on P3HT/IC₇₀BA is superior to that of the PEDOT:PSS buffer layer, not only showing a higher device stability but also resulting in a better photovoltaic performance of the PSCs.