GHP与除湿相结合的复合空调系统

介绍了一种燃气发动机热泵（GHP）与除湿转轮的复合空调系统，夏季将回收的发动机余热用于除湿转轮再生、承担湿负荷；冬季通过排热回收减小空调系统的采暖负荷。对比了复合空调系统、单独使用GHP、电动空调系统的能耗情况。     

固体转轮除湿与冷凝除湿的适用性研究

针对不同工况,对固体除湿转轮进行吸湿与再生的性能实验;根据实验结果,采用空气源热泵作为冷热源,通过理论计算得出不同条件下固体转轮除湿与冷凝除湿两种方式的性能。结果表明,相同工况除湿量相同时,转轮除湿相对于冷凝除湿功耗大、效率低;随着室内空气湿度的增大,2种除湿系统能耗都减小,效率增大,冷凝除湿效率改善更明显;室外空气湿度增大,对冷凝除湿性能影响较小,转轮除湿功耗变大,效率降低;室外空气温度升高,冷凝除湿功耗增大,转轮除湿功耗减小,但两者的效率均增大。     

利用冷凝热再生的复合除湿空调除湿潜力分析

简要描述了利用冷凝热再生的复合除湿空调系统形式及其节能性特点;在热力学第一定律和热力学第二定律的基础上,分别以冷凝器和除湿转轮为控制体,建立了复合除湿空调的系统热力学模型,并给出模型求解框图,从而可以求得复合除湿空调系统的除湿量;最后,计算了在不同转轮效率和室内单位面积显热负荷下的系统单位面积除湿量,并讨论了新风量大小对结果的影响;结果表明,在现有转轮效率和常见单位面积负荷指标下,转轮的除湿量小于新风湿负荷（1次/h）,而降低新风量后（0.5次/h）,当转轮效率较高和室内显热负荷较大时,转轮能够承担新风湿负荷。     

Performance analysis on a hybrid air-conditioning system of a green building

This paper presents the performance analysis on a hybrid air-conditioning system according to the hybrid building energy system of the green building demonstration project in Shanghai, in which a 150 m² solar collector is used to power two 10 kW adsorption chillers, a vapor compression heat pump is used to cool air in the evaporating end while the condensing heating at about 80 °C is fully used to regenerate a liquid desiccant dehumidification system. In the hybrid system, the sensible cooling to the air is treated mainly by solar adsorption cooling and vapor compression cooling, whereas the latent heat is treated by the liquid desiccant dehumidification system with regeneration from the condensing heat of the heat pump. The results show that the performance of this system is 44.5% higher than conventional vapor compression system at a latent load of 30% and this improving can be achieved by 73.8% at a 42% latent load. The optimal ratio of adsorption refrigerating power to total cooling load for this kind of hybrid systems is also studied in this paper.     

A combined system of chilled ceiling,displacement ventilation and desiccant dehumidification

Different types of heating, ventilation, and air-conditioning (HVAC) systems consume different amounts of energy yet they deliver similar levels of acceptable indoor air quality (IAQ) and thermal comfort. It is desirable to provide buildings with an optimal HVAC system to create the best IAQ and thermal comfort with minimum energy consumption. In this paper, a combined system of chilled ceiling, displacement ventilation and desiccant dehumidification is designed and applied for space conditioning in a hot and humid climate. IAQ, thermal comfort, and energy saving potential of the combined system are estimated using a mathematical model of the system described in this paper. To confirm the feasibility of the combined system in a hot and humid climate, like China, and to evaluate the system performance, the mathematical model simulates an office building in Beijing and estimates IAQ, thermal comfort and energy consumption. We conclude that in comparison with a conventional all-air system the combined system saves 8.2% of total primary energy consumption in addition to achieving better IAQ and thermal comfort. Chilled ceiling, displacement ventilation and desiccant dehumidification respond consistently to cooling source demand and complement each other on indoor comfort and air quality. It is feasible to combine the three technologies for space conditioning of office building in a hot and humid climate.     

Experimental study on dehumidifier and regenerator of liquid desiccant cooling air conditioning system

A new type of air conditioning system, the liquid desiccant evaporation cooling air conditioning system (LDCS) is introduced in this paper. Desiccant evaporation cooling technology is environmental friendly and can be used to condition the indoor environment of buildings. Unlike conventional air conditioning systems, the system can be driven by low-grade heat sources such as solar energy and industrial waste heat with temperatures between 60 and 80 °C. In this paper, a LDCS, as well as a packed tower for the regenerator and dehumidifier is described. The effects of heating source temperature, air temperature and humidity, desiccant solution temperature and desiccant solution concentration on the rates of dehumidification and regeneration are discussed. Based on the experimental results, mass transfer coefficients of the regeneration process were experimentally obtained. The results showed that the mean mass transfer coefficient of the packing regenerator was 4 g/(m² s). In the experiments of dehumidification, it was found that there was maximal tower efficiency with the suitable inlet humidity of the indoor air. The effective curves of heating temperature on the outlet parameters of the regenerator were obtained. The relationships of regeneration mass transfer coefficient as a function of heating temperature and desiccant concentration are introduced.     

转轮除湿与单元式空调机相结合的空气处理系统

本文介绍了转轮除湿与直接膨胀式单元机组相结合的复合空调系统的2种紧凑型组成形式:前置预冷与后置冷却,并在几种不同室外工况下,针对应用于独立新风系统,对比分析了这2种典型组成方案的性能特点。结果表明,这2种除湿方式在4种典型工况下的制冷能耗相差不明显,在10%以内;但后置冷却除湿在高温高湿工况下难以实现较大的单位除湿量,且再生空气温度高;而前置预冷除湿系统采用较小的除湿转轮尺寸,结构更紧凑,可明显降低初投资,且再生空气温度较低。因此,前置预冷除湿系统在较小流量空气处理应用方面更具优势,更具商品化发展潜力。     

Experiences with a gas driven,desiccant assisted air conditioning system with geothermal energy for an office building

Thermal driven desiccant assisted air conditioning systems make use of waste heat to dehumidify humid outside air in a desiccant wheel. Within the scope of a research project, an investigation of a desiccant assisted air conditioning system was carried out, and a demonstration plant was built in an office building in Hamburg, Germany. The HVAC system consists of a small CHP-plant, a desiccant assisted ventilation system and an earth energy system (borehole heat exchangers) for cooling instead of an electric driven compression chiller. The radiant floor heating system of the building is used for cooling. In this paper, measurement results and investigations of performance, energy demand and operating costs will be presented. It was found that considerable primary energy savings can be achieved (70%) using desiccant air conditioning with borehole heat exchangers. But even if electric chiller is used, savings of 30% in primary energy can be accomplished. Starting costs for the demonstration plant were not higher than for a conventional system, but running costs could be reduced drastically.     

转轮除湿与冷却除湿相结合的复合式除湿工艺空调系统

介绍一个转轮除湿与冷却除湿相结合的复合式除湿工艺空调系统，分析比较氯化钙、乙二醇冷冻水载冷剂在同一温度之间及同一载冷剂在不同温度下的换热系数差异，分析该工艺空调系统不能正常运行的原因，并提出改进措施。     

上海地区使用风冷热泵冷热水机组的经济性分析

作者利用上海地区ＢＩＮ气象参数计算出风冷热泵机组的供热季节性能系数，分别比较了办公楼、旅馆和商场的能耗，指出在上海地区的中小规模建筑中应用风冷热泵冷热水机组有较高的能效比，且不需要冬季辅助加热，并提出多机组联供的方案，可以进一步降低能耗和初投资。     

Performance analysis of liquid desiccant based air-conditioning system under variable fresh air ratios

In conventional air-conditioning system, fresh air volume is always restricted to save energy, which sacrifices indoor air quality (IAQ) to some extent. However, removing the latent load of air by liquid desiccant rather than by cooling is an alternative way of reducing energy consumption. Therefore, IAQ can be improved by increasing the volume of fresh air introduced into an air-conditioning system. In this paper, a liquid desiccant based air-conditioning system is studied, with the system performance under various fresh air ratios analyzed using simulation tests. In addition, the proposed system and a conventional system are compared. In the proposed system, with the increase in fresh air ratio, the heating load for solution regeneration rises, the dehumidification efficiency increases and the regeneration efficiency drops. The coefficient of performance (COP) of the liquid desiccant based system decreases sharply when the fresh air ratio exceeds 60%. The results also show that the proposed system can save power notably. The maximum power saving ratio is 58.9% when the fresh air ratio is 20%; however, the ratio drops when the fresh air ratio increases. These findings will be beneficial in the selection of fresh air ventilation strategies for liquid desiccant based air-conditioning systems.     

转轮除湿复合式空调系统

介绍了转轮除湿与常规冷却及蒸发冷却相结合的两类复合式空调系统。指出了在要求低湿或湿负荷较大的场合,采用前者既可避免制冷机的蒸发温度过低影响制冷效率,又可避免凝结水排放不当造成渗漏等问题,利于节能;采用后者,节能效果更显著,而且既无ＣＦＣ问题,又能缓解夏季电力供应紧张的压力。     

Advancement of solar desiccant cooling system for building use in subtropical Hong Kong

The solar desiccant cooling system (SDCS) had a saving potential of the year-round primary energy consumption as compared to the conventional air-conditioning system for full fresh air application in the subtropical Hong Kong. In order to further enhance its energy efficiency, advancement of the basic SDCS was carried out through a strategy of hybrid design. Six hybrid system alternatives of SDCS were therefore proposed, three for full fresh air design while another three for return air design for the building zone. Year-round performance evaluation of each solar hybrid desiccant cooling system was conducted for typical office application under different climatic and loading conditions. All the six hybrid system alternatives were found technically feasible, with up to 35.2% saving of year-round primary energy consumption against the conventional air-conditioning systems. Among the hybrid alternatives, recommendations were made on the SDCS hybridized with vapour compression refrigeration for full fresh air design; and the SDCS hybridized with vapour absorption refrigeration for return air design, since they had the saving potentials of both primary energy and initial cost. These two hybrid system alternatives used evacuated tubes, a more economical type of solar collectors compared to the PV or PVT panels.     

Performance of combined displacement ventilation and cooled ceiling liquid desiccant membrane system in Beirut climate

The performance of the chilled ceiling (CC) displacement ventilation (DV) systems is constrained by latent load removal capacity and cost of supply air dehumidification to prevent condensation on the ceiling. In this study, a liquid desiccant dehumidification membrane cycle (LDMC) is mathematically modelled to replace the CC and remove directly latent and sensible load from indoor space through the membrane. The desiccant system is coupled with the DV system. An optimized operational strategy is adopted while allowing ceiling temperature to drop to lower values than conventional CC/DV. The optimized LDMC-C/DV system was implemented in an office space in Beirut climate. It was found that decreasing the membrane liquid desiccant temperature resulted in a significant decrease in the total cooling energy of the system, while increasing the solar heating energy of the desiccant regeneration. At optimal set points, a decrease of 49% in energy consumption was observed compared to the conventional CC/DV system.     

Simulation of hybrid ground-coupled heat pump with domestic hot water heating systems using HVACSIM+

A hybrid ground-coupled heat pump (HGCHP) with domestic hot water (DHW) supply system has been proposed in this paper for space cooling/heating and DHW supply for residential buildings in hot-climate areas. A simulation model for this hybrid system is established within the HVACSIM+ environment. A sample system, applied for a small residential apartment located in Hong Kong, is hourly simulated in a typical meteorological year. The conventional GCHP system and an electric heater for DHW supply are also modeled and simulated on an hourly basis within the HVACSIM+ for comparison purpose. The results obtained from this case study show that the HGCHP system can effectively alleviate the imbalanced loads of the ground heat exchanger (GHE) and can offer almost 95% DHW demand. The energy saving for DHW heating is about 70% compared with an electric heater. This proposed scheme, i.e. the HGCHP with DHW supply, is suitable to residential buildings in hot-climate areas, such as in Hong Kong.     

某高压电机装配车间环境控制的实测分析与研究

通过对某高压电机装配车间进行实测,研究了空调风量对恒温恒湿车间工作区空气温湿度均匀性的影响;并与对空调冷负荷的分析相结合,进一步明确影响室内空气湿度最重要的因素是新风,影响室内空气温度最重要的因素是厂房内的工艺设备的散热量;根据高压电机生产车间的低湿环境要求,综合考虑技术性和经济性,对空调湿负荷的处理方式进行了优化研究,提出冷却除湿+转轮除湿复合除湿系统是能够达到此要求的最优化方法.     

我国建筑耗能状况及有效的节能途径

简要分析了我国建筑能源消耗状况,从用能特点出发,对建筑物和建筑用能途径进行了新的分类,给出各类的现状、问题和节能潜力。在此基础上列出为实现建筑节能所需要的主要技术与产品研究领域和政策研究与保障机制。文中列出的关键技术研究为：基于模拟分析的建筑节能优化设计;新型建筑围护结构材料与部品;通风装置与排风热回收装置;热泵技术;降低输配系统能源消耗的技术;集中空调的温度湿度独立控制技术;建筑自动化系统的节能优化控制;楼宇式燃气驱动的热电冷三联供技术;燃煤燃气联合供热和末端调峰技术;节能灯、节能灯具与控制。有关政策与保障机制的研究问题为：建筑能耗数据的统计系统;住宅能耗标识方法与保障机制;大型公共建筑能耗评估与用能配额制;各种建筑用能装置的能耗标识标准与方法。     

夏热冬冷地区办公建筑降低供暖空调能耗的技术路径

以上海地区某办公建筑为例,基于EnergyPlus能耗模拟,探讨了围护结构性能提升和暖通空调系统优化这2条节能技术路径对夏热冬冷地区办公建筑降低供暖空调全年能耗的有效性.结果 表明:围护结构性能提升的节能潜力较小,经济性较差;单纯提高围护结构保温隔热性能并不能保证降低建筑年耗冷量,应综合分析全年供热供冷能耗确定围护结构...     

夏季湿热地区置换通风和冷却顶板复合系统节能潜力研究

根据上海一办公楼置换通风和冷却顶板复合系统的设计及运行特点,应用EnergyPlus软件模拟了采用转轮除湿方式的复合系统的供冷季能耗,并分别模拟了采用冷却除湿方式的复合系统、带热回收装置的混合通风系统和置换通风系统的供冷季能耗以进行对比。结果表明,在湿热地区采用转轮除湿方式可比冷却除湿方式节约制冷机冷量,空调季总能源费用比混合通风系统节约30%左右。     

污水热泵在城市生活小区的应用

从就近利用小区污水冷热能的角度出发,对重庆市主城区某居住小区生活污水的温度和流量进行了测试分析,提出了小区污水热泵系统应用于建筑空调、供暖和卫生热水供应的综合节能系统模式;调研了小区生化池内污水温度分布,分析了小区污水逐时流量及逐月流量的变化,讨论了小区污水所能提供的冷量与建筑实际需要冷负荷的匹配关系,提出了生活小区污水热泵系统与常规冷热供应系统的复合式冷热供应方案。