Crystallization and Dielectric Properties of SrO–BaO–Nb2O5–SiO2 Tungsten-Bronze Glass-Ceramics

The crystallization and dielectric properties of SrO–BaO–Nb₂O₅–SiO₂ glass-ceramics have been investigated. Glass-ceramics that contain strontium barium niobate (SBN) as a primary crystalline phase, which has a tungsten bronze structure, are produced. The formation of crystalline secondary phases also has been studied. The SBN phase shows evidence of both surface nucleation and bulk nucleation, and the crystals have an average composition of Sr_0.47Ba_0.53Nb₂O₆. The dendritic morphology of the SBN crystals has been examined. The SBN content and composite dielectric constant each has been studied as a function of heating temperature/time. The highest SBN content and dielectric constant obtained in the present study are 42 vol% and 180, respectively. The dielectric constant of the glass-ceramics is determined primarily by the SBN content and the residual glass phase. The dielectric constant of the randomly oriented SBN crystal in the glass-ceramics is calculated, using dielectric mixture rules, to be ∼400.     

Spectroscopic Properties of Er3+-Doped Na2O–La2O3–Al2O3–SiO2 Glasses

Er³⁺-doped sodium lanthanum aluminosilicate glasses with compositions of (90− x )(0.7SiO₂·0.3Al₂O₃)· x Na₂O·8.2La₂O₃· 0.6Er₂O₃·0.2Yb₂O₃·1Sb₂O₃ (in mol%) ( x = 12, 20, 24, 40, 60 mol%) were prepared and their spectroscopic properties were investigated. Judd–Ofelt analysis was used to calculate spectroscopic properties of all glasses. The Judd–Ofelt intensity parameter Ω _t ( t = 2, 4, 6) decreases with increasing Na₂O. Ω₂ decreases rapidly with increasing Na₂O while Ω₄ and Ω₆ decrease slowly. Both the fluorescent lifetime and the radiative transition rate increase with increasing Na₂O. Fluorescence spectra of the ⁴ I _13/2 to ⁴ I _15/2 transition have been measured and the change with Na₂O content is discussed. It is found that the full width at half-maximum decreases with increasing Na₂O.     

Microwave Dielectric Properties of 5Li2O–0.583Nb2O5–3.248TiO2 Ceramics with V2O5

The effects of V₂O₅ addition on the sintering behavior, microstructure, and the microwave dielectric properties of 5Li₂O–0.583Nb₂O₅–3.248TiO₂ (LNT) ceramics have been investigated. With addition of low-level doping of V₂O₅ (≤2 wt%), the sintering temperature of the LNT ceramics could be lowered down to around 920°C due to the liquid phase effect. A secondary phase was observed at the level of 2 wt% V₂O₅ addition. The addition of V₂O₅ does not induce much degradation in the microwave dielectric properties but lowers the τ_f value to near zero. Typically, the excellent microwave dielectric properties of ɛ_r=21.5, Q × f =32 938 GHz, and τ_f=6.1 ppm/°C could be obtained for the 1 wt% V₂O₅-doped sample sintered at 920°C, which is promising for application of the multilayer microwave devices using Ag as an internal electrode.     

Structure, Thermal Behavior, Chemical Durability, and Optical Properties of the Na2O–Al2O3–TiO2–Nb2O5–P2O5 Glass System

The FTIR, Raman, UV-Vis, ³¹P MAS-NMR, DTA, and refractive index measurements have been combined to investigate a series of glasses with the general formula 20Na₂O–5Al₂O₃− x TiO₂–(45− x )Nb₂O₅–30P₂O₅, 15≤ x ≤45. The glass structure, as well as thermal, optical, and chemical durability properties, were then described as functions of the f _Nb/ f _Ti ratio. An increase of the f _Nb/ f _Ti ratio correlates with a decrease in length of the average phosphate chains linked through Nb–O–P and Ti–O–P bonds, with an increase in the glass stability and with increase in the linear refractive indices at 632.8 nm from 1.79 to 1.89. Furthermore, niobium is more effective than titanium in improving chemical durability.     

Effect of Molybdenum on the Structure and on the Crystallization of SiO2–Na2O–CaO–B2O3 Glasses

Crystallization of the poorly durable Na₂MoO₄ phase able to incorporate radioactive cesium must be avoided in SiO₂–Al₂O₃–B₂O₃–Na₂O–CaO glasses developed for the immobilization of Mo-rich nuclear wastes. Increasing amounts of B₂O₃ and MoO₃ were added to a SiO₂–Na₂O–CaO glass, and crystallization tendency was studied. Na₂MoO₄ crystallization tendency decreased with the increase of B₂O₃ concentration whereas the tendency of CaMoO₄ to crystallize increased due to preferential charge compensation of BO₄⁻ entities by Na⁺ ions. ²⁹Si MAS NMR showed that molybdenum acts as a reticulating agent in glass structure. Trivalent actinides surrogate (Nd³⁺) were shown to enter into CaMoO₄ crystals formed in glasses.     

Structure of Na2O–CaO–P2O5–SiO2 Glass–Ceramics with Multimodal Porosity

We have investigated the evolution of the structure of nano–macro porous CaO–Na₂O–P₂O₅–SiO₂ bioactive glass–ceramics by Fourier transform infrared (FTIR) and Raman spectroscopies, and X-ray diffraction (XRD). A controlled devitrification, followed by a chemical leaching treatment is used to produce a multimodal distribution of nano/macro pores that are expected to improve cell attachment. Data show that the leaching process removes the sodium- and calcium-containing crystalline phases that are formed during the ceramming heat treatment. The primary Si–O peaks in the infrared spectra blue shift with leaching, indicating that the sample becomes SiO₂ rich. In parallel, the fraction of nonbridging oxygen decreases. These results suggest a restructuring of the glass network far below the glass transition temperature. The stresses from leaching, capillary forces, and subsequent restructuring develop and grow, eventually producing cracks in the sample.     

The Li2O–Nb2O5–TiO2 Composite Microwave Dielectric Ceramics with Adjustable Permittivities

A group of new y M-phase/(1− y ) Li_{2+ x} Ti_{1−4 x} Nb_{3 x} O₃ composite ceramics with adjustable permittivities for low-temperature co-fired ceramic applications was initially investigated in the study. The 0.5 M-phase/0.5 Li_{2+ x} Ti_{1−4 x} Nb_{3 x} O₃ ( x =0.01, 0.02, 0.04, 0.06, 0.081) composite ceramics were first investigated to find the appropriate "Li₂TiO₃ss" composition ( x value). The best dielectric properties of ɛ_r=40.1, Q × f values up to 9318 GHz, τ_f=25 ppm/°C, were obtained for the ceramics composites at x =0.02. Based on the good dielectric properties, the suitable "Li₂TiO₃ss" composition with x =0.02 was mixed with the Li_1.0Nb_0.6Ti_0.5O₃ powder as the ratio of y "M-phase"/(1− y ) "Li₂TiO₃ss" ( y =0.2, 0.4, 0.5, 0.6, 0.8). By adjusting the y values, the group of composite ceramics could exhibit largely are adjustable permittivities varying from ∼20 to ∼60, while Q × f and τ_f values relatively good. Nevertheless, in this study, because there are interactions between the M-phase and Li₂TiO₃ss during sintering process, their microwave dielectric properties could not be predicted precisely by the empirical model.     

Mixed-Alkali Effect on Rayleigh Scattering in K2O–Na2O–MgO–SiO2 Glasses

The Rayleigh scattering of the mixed-alkali glass system K₂O–Na₂O–MgO–SiO₂ (KNMS) was investigated, both experimentally and theoretically. The lowest Rayleigh scattering coefficient (38% of that for pure SiO₂ glass) was obtained when the glass composition was 22K₂O–8Na₂O–10MgO–60SiO₂ (in mol%). These values are equal to or less than the minimum values reported for the ternary sodium silicate glass Na₂O–MgO–SiO₂. The Rayleigh scattering caused by concentration fluctuation was believed to have been reduced greatly in this KNMS glass, because the mobility of the alkali-metal ions was reduced by the mixed-alkali effect.     

Influence of V2O5 Additions to 5Li2O–1Nb2O5–5TiO2 Ceramics on Sintering Temperature and Microwave Dielectric Properties

The effects of the addition of V₂O₅ on the sintering behavior, microstructure, and microwave dielectric properties of 5Li₂O–1Nb₂O₅–5TiO₂ (LNT) ceramics have been investigated. With low-level doping of V₂O₅ (≤3 wt%), the microstructure of the LNT ceramic changed from a special two-level intergrowth structure into a two-phase composite structure with separate grains. And the sintering temperature of the LNT ceramics could be lowered to around 900°C by adding a small amount of V₂O₅ without much degradation in microwave dielectric properties. Typically, better microwave dielectric properties of ɛ_r=41.7, Q × f =7820 GHz, and τ _f =45 ppm/°C could be obtained for the 1 wt% V₂O₅-doped ceramics sintered at 900°C.     

The Binary System Nb2O5— SiO2

The binary system Nb₂O₅— SiO₂ has been shown to include an extensive two-liquid region over the range 5 to 80% Nb₂O₅. The minimum temperature of the two-liquid area is 1695°C. A eutectic composition occurs at 95% Nb₂O₅ and 1448°C. and another at approximately 5% Nb₂O₅ and 1695°C. The experimental results were obtained by the cone-fusion method.     

Dielectric Relaxations in Bi2O3–Nb2O5–NiO Cubic Pyrochlores

Dielectric properties of pyrochlores compositions from Bi₂O₃–Nb₂O₅–NiO system were analyzed. The dielectric properties are dominated with a low-temperature relaxation that is typical for Bi-pyrochlores. A vast pyrochlore homogeneity range that exists in this system allowed to correlate characteristics of the observed relaxations with a compositional variations within the A₂O'- and B₂O₆ pyrochlore sublattice. It was possible to make a distinction between different influences of the two sublattices, which can be satisfactorily described by the existing relaxation model for Bi_3/2ZnNb_3/2O₇. A new relaxor-like room temperature relaxation was found for Bi_1.6Ni_0.57Nb_1.43O_6.55.     

Optimization of the Thermodynamic Properties and Phase Diagrams of the Na2O–SiO2 and K2O–SiO2 Systems

Available thermodynamic and phase diagram data have been evaluated for all phases in the Na₂O-SiO₂ and K₂O-SiO₂ systems at 1 bar pressure from 298 K to above the liq-uidus temperatures. All reliable thermodynamic and phase diagram data have been simultaneously optimized in order to obtain one set of model equations for the Gibbs energies of all phases as functions of temperature and composition. The thermodynamic properties and phase diagrams calculated from these parameters are self-consistent. The modified quasi-chemical model was used to represent the Gibbs energies of the molten slag phases.     

Energetics of La2O3–HfO2–SiO2 Glasses

A series of La₂O₃–HfO₂–SiO₂ glasses, approximately along the join 0.73SiO₂–0.27( x HfO₂–(1− x )La₂O₃), 0< x <0.3), was prepared using containerless processing techniques (aerodynamic levitation combined with laser heating in oxygen). The enthalpy of formation and enthalpy of vitrification at 25°C were obtained from drop solution calorimetry of these glasses and appropriate crystalline compounds in a molten lead borate (2PbO–B₂O₃) solvent at 702°C. The enthalpy of formation from crystalline oxides was exothermic and became less exothermic with increasing HfO₂ content. Heat contents were measured by transposed temperature drop calorimetry and depended linearly on the HfO₂ content. Differential scanning calorimetry showed that both the onset glass transition and the onset crystallization temperature of these glasses increased with increasing HfO₂ content. Upon slow cooling in air, the glasses crystallized to a mixture of baddeleyite, cristobalite, lanthanum disilicate, and hafnon.     

Effect of Sb2O3 on Thermal Properties of Glasses in Bi2O3–B2O3–SiO2 System

Glasses with compositions 50Bi₂O₃– x Sb₂O₃–10B₂O₃–(40– x ) SiO₂ ( x =0, 1, 3, 5, 8, 10) have been prepared by conventional melt quench technique. Substitution of Sb₂O₃ for SiO₂ exerted an obvious effect on properties of glasses, especially, increased glass transition temperature ( T _g) and crystalline temperature ( T _c) greatly. Results of infrared transmission spectra attributed the effect to the formation of new bridging bonds of Sb–O–B and Sb–O–Si in glass network.     

Investigation on the Microstructure and Dielectric Properties of BaTiO3–Nb2O5–Fe2O3 Materials Doped with La2O3

The influence of La₂O₃ doped on the microstructure and dielectric properties, including the phase structure, temperature dependence of permittivity, and the hysteresis loop of BaTiO₃–Nb₂O₅–Fe₂O₃ (BTNF) materials has been investigated in X-ray diffraction, SEM, and LCR analyzer, respectively. Experiments revealed that incorporation of proper content of La₂O₃ basically soluted in the lattice of BaTiO₃ and can control the grain-growth, reduce the dielectric loss of the BTNF materials. The development of microstructure promoted by the additives can result in the improvement of the dielectric constant. When the doping concentration of La₂O₃ was 3.846 wt%, the relative dielectric constant of the sample sintered at 1280°C only for 2 h could reach 4308, and improve the dielectric-temperature characteristics markedly. As a result, a novel Y5P can be achieved in the BTNF ceramics, which is very promising for practical use in Y5P multilayer ceramic capacitors.     

Phase Equilibria in the System Na2O – Nb2O5

Phase equilibria data, obtained both by differential thermal analysis and by quenching, are presented for the system Na₂O-Nb₂O₅. Five compounds corresponding to the formulas 3Na₂O.1Nb₂0₆, lNa₂O. 1Nb₂O₅, lNa₂O 4Nb₂O₆, lNa_zO.7Nb₂O₅, and lNa₂O. 10Nb₂O₆ have been found. The compound 3Na_z0.lNb₂O₅ melts congruently at 992°C. The compounds 1Na₂O. 4Nb₂O₆, lNa₂O.7Nb₂O, and 1Na₂O. 1Onb₂O₅ melt incongruently at 1265°, 1275°, and 1290°C., respectively. The well-known perovskite structure phase NaNbO₃ was found to melt congruently at 1412°C. The transition temperatures in NaNbO₅ were checked by thermal analysis and only the major structural changes at 368° and 640°C. could be detected. A new disordered form of NaNbO₃ could be preserved to room temperature by very rapid quenching.     

Deposition and Characterization of Li2O–SiO2–P2O5 Thin Films

Amorphous lithium electrolyte thin films, xLi₂O·ySiO₂·zP₂O₅, were deposited by rf magnetron sputtering of pure and mixed-phase lithium silicate, lithium phosphate, SiO₂, Li₂O, and Li₂CO₃ targets, and their compositions were determined using proton-induced y -ray emission spectroscopy, energy-dispersive X-ray analysis, Rutherford backscattering spectrometry, and atomic-emission spectroscopy. The deposition conditions were chosen to assure thermalization of the sputtered flux, which proved to be necessary in order to obtain a homogeneous distribution of Si and P in the films. Optical absorption and ac impedance measurements showed that glass-in-glass phase separation occurred in a large SiO₂-rich domain of the composition diagram. In contrast to bulk glasses, all of the Li₂O–SiO₂ films were phase-separated, including those with lithia contents larger than lithium disilicate. High-performance liquid chromatography measurements revealed that, analogous to bulk glasses, the addition of SiO₂ to Li₂O-P₂O₅ compositions reduced the number of phosphate anion dimers, trimers, and higher anion polymers in the films through the formation of -Si-O-P-bonds. However, in contrast to bulk glasses, the distribution of phosphate anion polymers followed closely the Flory distribution, with the fraction of anion polymers decreasing monotonically with increasing chain length.     

The System SiO2–P2O2

Phase relations in the binary system between SiO₂-P₂O₅ and SiO₂ were investigated by the quenching method using sealed platinum tubes to prevent the loss of P₂O₅. The compound Si0₂-P₂O₅ exists in two forms, the low-temperature β form inverting sluggishly but reversibly to the high-temperature β form at 1030°C. The β form melts congruently at 1290°C. The compound 2SiO₂-P₂O₅ melts incongruently at 1120°C to a silica-rich liquid and SiO_a-P₂O₅. In the region between 5 and 25 mole % PO₂, reactions were so sluggish that no data could be obtained by quenching.     

Formation and Transformation of Solid Solutions in the System Nb2O5–Ta2O5

In the system Nb₂O₅–Ta₂O₅, a continuous series of δ-Nb₂O₅ (δ-Ta₂O₅) solid solutions with a hexagonal cell is formed while heating amorphous materials prepared by the simultaneous hydrolysis of niobium and tantalum alkoxides. The lattice parameters a and c change linearly with increasing Ta₂O₅ content; the former value increases from 0.3604 to 0.3620 nm, and the latter value decreases from 0.3923 to 0.3883 nm. They transform to γ-Nb₂O₅ (β-Ta₂O₅) solid solutions with an orthorhombic cell at higher temperatures. The changes in lattice parameters a and c as functions of composition are the same as those of hexagonal solid solutions, whereas parameter b is relatively constant.