A 2.5-V 10-b 120-MSample/s CMOS pipelined ADC based on merged-capacitor switching

This work describes a 10-b multibit-per-stage pipelined CMOS analog-to-digital converter (ADC) incorporating the merged-capacitor switching (MCS) technique. The proposed MCS technique improves the signal processing speed and resolution of the ADC by reducing the required number of unit capacitors by half in comparison to a conventional ADC. The ADC resolution based on the proposed MCS technique can be extended further by employing a commutated feedback-capacitor switching (CFCS) technique. The prototype ADC achieves better than 53-dB signal-to-noise-and-distortion ratio (SNDR) at 120 MSample/s and 54-dB SNDR and 68-dB spurious-free dynamic range (SFDR) for input frequencies up to Nyquist at 100 MSample/s. The measured differential and integral nonlinearities of the prototype are within /spl plusmn/0.40 LSB and /spl plusmn/0.48 LSB, respectively. The ADC fabricated in a 0.25-/spl mu/m CMOS occupies 3.6 mm/sup 2/ of active die area and consumes 208 mW under a 2.5-V power supply.     

A 1.5 V 12-bit 16 MSPS CMOS Pipelined ADC with 68 dB Dynamic Range

A 1.5 V, 12-bit, 16 MSPS analog-to-digital converter was implemented in 0.25 μm 1P5 M standard CMOS process with MIM capacitors. The converter achieves a peak SNDR of 66.5 dB with 5.12 MSPS and that of 63.0 dB with 16.384 MSPS. The dynamic range is 68 dB under both sampling rates. The maximum INL of ±0.8 LSB and DNL of ±0.5 LSB were measured under 5.12 MSPS, while those of 16.384 MSPS decreased to ±3.1 and ±1.0 LSB, respectively. An embedded bandgap reference circuit that provides the conversion voltage range is also presented with 1.5 V supply voltage. The total power consumption of this converter was 138 mW under 16.384 MSPS or 97 mW under 5.12 MSPS. The total area of this chip is 2.8 × 2.5 mm. This chip was implemented without calibration or trimming approaches.     

A 1.2-V 19.2-mW 10-bit 30-MS/s pipelined ADC in 0.13-icm CMOS

A 10-bit 30-MS/s pipelined analog-to-digital converter (ADC) is presented.For the sake of lower power and area,the pipelined stages are scaled in current and area,and op amps are shared between the successive stages.The ADC is realized in the 0.13-tt,m 1-poly 8-copper mixed signal CMOS process operating at 1.2-V supply voltage.Design approaches are discussed to overcome the challenges associated with this choice of process and supply voltage,such as limited dynamic range,poor analog characteristic devices,the limited linearity of analog switches and the embedded sub-1-V bandgap voltage reference.Measured results show that the ADC achieves 55.1-dB signal-to-noise and distortion ratio,67.5-dB spurious free dynamic range and 19.2-mW power under conditions of 30 MSPS and 10.7-MHz input signal.The FoM is 0.33 pJ/step.The peak integral and differential nonlinearities are 1.13 LSB and 0.77 LSB,respectively.The ADC core area is 0.94 mm2.     

An 8-bit 20-MS/s ZCBC Time-Domain Analog-to-Digital Data Converter

An 8-bit 20-MS/s time-domain analog-to-digital data converter (ADC) using the zero-crossing-based circuit technique is presented. Compared with the conventional ADCs, signal processing is executed in both the voltage and time domains. Since no high-gain operational amplifier is needed, this time-domain ADC works well in a low supply voltage. The proposed ADC has been fabricated in a 0.18-mum CMOS process. Its power dissipation is 4.64 mW from a supply voltage of 1.8 V. This active area occupies 1.2 times 0.7 mm². The measured signal-to-noise-distortion ratio achieves 44.2 dB at an input frequency of 10 MHz. The integral nonlinearity is less than plusmn1.07 LSB, and the differential nonlinearity is less than plusmn0.72 LSB. This time-domain ADC achieves the effective bits of 7.1 for a Nyquist input frequency at 20 MS/s.     

A 600-MS/s 5-bit pipeline A/D converter using digital reference calibration

The design of a 600-MS/s 5-bit analog-to-digital (A/D) converter for serial-link receivers has been investigated. The A/D converter uses a closed-loop pipeline architecture. The input capacitance is only 170 fF, making it suitable for interleaving. To maintain low power consumption and increase the sampling rate beyond the amplifier settling limit, the paper proposes a calibration technique that digitally adjusts the reference voltage of each pipeline stage. Differential input swing is 400 mV/sub p-p/ at 1.8-V supply. Measured performance includes 25.6 dB and 19 dB of SNDR for 0.3-GHz and 2.4-GHz input frequencies at 600 MS/s for the calibrated A/D converter. The suggested calibration method improves SNDR by 4.4 dB at 600 MS/s with /spl plusmn/0.35 LSB of DNL and /spl plusmn/0.15 LSB of INL. The 180 /spl times/ 1500 /spl mu/m/sup 2/ chip is fabricated in a 0.18-/spl mu/m standard CMOS technology and consumes 70 mW of power at 600 MS/s.     

An 11b 70-MHz 1.2-mm/sup 2/ 49-mW 0.18-/spl mu/m CMOS ADC with on-chip current/voltage references

This work proposes an 11b 70-MHz CMOS pipelined analog-digital converter (ADC) as one of core circuit blocks for very high speed digital subscriber line system applications. The proposed ADC for the internal use has the strictly limited number of externally connected I/O pins while the ADC employs on-chip CMOS current/voltage references and a merged-capacitor switching technique to improve ADC performances. The ADC implemented in a 0.18-/spl mu/m 1P4M CMOS technology shows the maximum signal-to-noise distortion ratio (SNDR) of 60 dB at 70 MSample/s. The ADC maintains the SNDR of 58 dB and the spurious-free dynamic resistance of 68 dB for input frequencies up to the Nyquist rate at 60 MSample/s. The measured differential and integral nonlinearities of the ADC are within /spl plusmn/0.63 and /spl plusmn/1.21 LSB, respectively. The active chip area is 1.2 mm/sup 2/ and the ADC consumes 49 mW at 70 MSample/s at 1.8 V.     

An 8-bit 2-Gsample/s folding-interpolating analog-to-digital converter in SiGe technology

This paper deals with the design and implementation of an 8-bit 2-Gsample/s folding-interpolating analog-to-digital converter (ADC) using a SiGe technology with a unity gain cutoff frequency f/sub T/ of 47 GHz. The high-speed high-resolution ADC has applications in direct IF sampling receivers for wideband communication systems. The converter occupies an area of 3.5 mm/spl times/3.5 mm including pads and exhibits an effective resolution bandwidth of 700 MHz at a sampling rate of 2 Gsample/s. The maximum DNL and INL are 0.5 and 1 LSB, respectively. The ADC dissipates 3.5W (including output buffers) from a 3.3-V power supply.     

55-mW 200-MSPS 10-bit pipeline ADCs for wireless receivers

A new power reduction technique for analog-to-digital converters (ADCs) is proposed in this paper. The power reduction technique is a kind of amplifier sharing technique and it is suitable for ADCs in a wireless receiver. A test chip, which contains two ADCs, is fabricated in 90-nm 1-poly 7-metal CMOS technology. The 10-bit ADC dissipates 55 mW from 1.2-V supply, when the ADC operates at 200 mega-samples per second (MSPS). The 10-bit, 200-MSPS ADCs achieve maximum differential nonlinearity (DNL) of 0.66 least significant bit (LSB), maximum integral nonlinearity (INL) of 1.00 LSB, a spurious-free dynamic range (SFDR) of 66.5 dB and a peak signal-to-noise plus distortion ratio (SNDR) of 54.4 dB that corresponds to 8.7 effective number of bits (ENOB). The active area is 1.8 mm /spl times/ 1.4 mm.     

A 3.3-V 12-b 50-MS/s A/D converter in 0.6-μm CMOS with over80-dB SFDR

A 12-b analog-to-digital converter (ADC) is optimized for spurious-free dynamic range (SFDR) performance at low supply voltage and suitable for use in modern wireless base stations. The 6-7-b two-stage pipeline ADC uses a bootstrap circuit to linearize the sampling switch of an on-chip sample-and-hold (S/H) and achieves over 80-dB SFDR for signal frequencies up to 75 MHz at 50 MSample/s (MSPS) without trimming, calibration, or dithering. INL is 1.3 LSB, differential nonlinearity (DNL) is 0.8 LSB. The 6-b and 7-b flash sub-ADCs are implemented efficiently using offset averaging and analog folding. In 0.6-μm CMOS, the 16-mm² ADC dissipates 850 mW     

A 14-bit digitally self-calibrated pipelined ADC with adaptive bias optimization for arbitrary speeds up to 40 MS/s

This paper presents a 14-bit digitally self-calibrated pipelined analog-to-digital converter (ADC) featuring adaptive bias optimization. Adaptive bias optimization controls the bias currents of the amplifiers in the ADC to the minimum amount required, depending on the sampling speed, environment temperature, and power-supply voltage, as well as the variations in chip fabrication. It utilizes information from the digital calibration process and does not require additional analog circuits. The prototype ADC occupies an area of 0.5/spl times/2.3 mm/sup 2/ in a 0.18-/spl mu/m dual-gate CMOS technology; with a power supply of 2.8 V, it consumes 19.2, 33.7, 50.5, and 72.8 mW when operating at 10, 20, 30, and 40 MS/s, respectively. The peak differential nonlinearity (DNL) is less than 0.5 least significant bit (LSB) for all the sampling speeds with temperature variation up to 80/spl deg/C. When operated at 20 MS/s with 1-MHz input, the ADC achieves 72.1-dB SNR and 71.1-dB SNDR.     

A 6-GSamples/s multi-level decision feedback equalizer embedded in a 4-bit time-interleaved pipeline A/D converter

A 4-bit 6-GS/s pipeline A/D converter with 10-way time-interleaving is demonstrated in a 0.18-/spl mu/m CMOS technology. The A/D converter is designed for a serial-link receiver and features an embedded adjustable single-tap DFE for channel equalization. The ISI subtraction of the DFE is performed at the output of each pipeline stage; hence the effective feedback delay requirement is relaxed by 6/spl times/. Code-overlapping of the 1.5-bit pipeline stage along with digital error correction is used to absorb and remove the remainder of the ISI. The measured A/D converter performance at 6-GSamples/s shows 22.5 dB of low-frequency input SNDR for the calibrated A/D converter with /spl plusmn/0.25 LSB and /spl plusmn/0.4 LSB of INL and DNL, respectively. The input capacitance is 170 fF for each A/D converter. The DFE tap coefficient is adjustable from 0 to 0.25 with 6-bits of programmable weight. With a DFE coefficient of 0.2, the measured DFE performance shows 2.5 dB of amplitude boosting for a 3-GHz input sinusoid. The 1.8/spl times/1.6 mm/sup 2/ chip consumes 780 mW of power from a 1.8-V power supply.     

A 100-MS/s 8-b CMOS subranging ADC with sustained parametricperformance from 3.8 V down to 2.2 V

A 100-MS/s 8-b CMOS analog-to-digital converter (ADC) designed for very low supply voltage and power dissipation is presented. This single-ended-input ADC is based on the unified two-step subranging architecture, which processes the coarse and fine decisions in identical signal paths to maximize their matching. However, to minimize power and area, the coarse-to-fine overlap correction has been aggressively reduced to only one LSB. The ADC incorporates five established design techniques to maximize performance: bottom-plate sampling, distributed sampling, autozeroing, interpolation, and interleaving. Very low voltage operation required for a general purpose ADC was obtained with four additional and new circuit techniques. These are a dual-gain first-stage amplifier, differential T-gate boosting, a supply independent delay generator, and a digital delay-locked-loop controlled output driver. For a clock rate of 100 MS/s, 7.0 (7.3) effective bits for a 50 MHz (10 MHz) input are maintained from 3.8 V down to 2.2 V. At 2.2 V, this 100-MS/s converter dissipates 75 mW plus 9 mW for the reference ladder. For a typical supply of 2.7 V, it consumes just 1 mW per MS/s over the 10-160-MS/s clock frequency range. Differential nonlinearity below 0.5 LSB is maintained from 2.7 V down to 2.2 V, and it degrades only slightly to 0.8 LSB at 3.8-V supply. The converter is implemented in a 0.35-μm CMOS process, with double-poly capacitors and no low-threshold devices     

A 0.9-V 12-mW 5-MSPS algorithmic ADC with 77-dB SFDR

An ultra-low-voltage CMOS two-stage algorithm ADC featuring high SFDR and efficient background calibration is presented. The adopted low-voltage circuit technique achieves high-accuracy high-speed clocking without the use of clock boosting or bootstrapping. A resistor-based input sampling branch demonstrates high linearity and inherent low-voltage operation. The proposed background calibration accounts for capacitor mismatches and finite opamp gain error in the MDAC stages via a novel digital correlation scheme involving a two-channel ADC architecture. The prototype ADC, fabricated in a 0.18 /spl mu/m CMOS process, achieves 77-dB SFDR at 0.9 V and 5MSPS (30 MHz clocking) after calibration. The measured SNR, SNDR, DNL, and INL at 80 kHz input are 50 dB, 50 dB, 0.6 LSB, and 1.4 LSB, respectively. The total power consumption is 12 mW, and the active die area is 1.4 mm/sup 2/.     

A 1.5-V 12-bit power-efficient continuous-time third-order /spl Sigma//spl Delta/ modulator

This paper presents the design strategy, implementation, and experimental results of a power-efficient third-order low-pass /spl Sigma//spl Delta/ analog-to-digital converter (ADC) using a continuous-time (CT) loop filter. The loop filter has been implemented by using active RC integrators. Several power optimizations, design requirements, and performance limitations relating to circuit nonidealities in the CT modulator are presented. The influence of the low supply voltage on the various building blocks such as the amplifier as well as on the overall /spl Sigma//spl Delta/ modulator is discussed. The ADC was implemented in a 3.3-V 0.5-/spl mu/m CMOS technology with standard threshold voltages. Measurements of the low-power 1.5-V CT /spl Sigma//spl Delta/ ADC show a dynamic range and peak signal-to-noise-plus-distortion ratio of 80 and 70 dB, respectively, in a bandwidth of 25 kHz. The measured power consumption is only 135 /spl mu/W from a single 1.5-V power supply.     

9位100 MSPS流水线结构A/D转换器的设计

提出一种采用三级流水线型结构的9位100 MSPS折叠式A/D转换器,具体分析了其内部结构。电路使用0.6 μm Bipolar工艺实现, 由5 V/3.3 V双电源供电, 经优化设计后, 实现了9位精度,100 MSPS的转换速度,功耗为650 mW,差分输入范围2.2 V。给出了在Cadence Spectre的仿真结果,讨论了流水线A/D转换器设计的关键问题。     

Low-power CMOS fully-folding ADC with a mixed-averaging distributed T/H circuit

This paper describes an 8-bit 125 Mhzlow-powerCMOS fully-foldinganalog-to-digital converter(ADC).A novel mixed-averaging distributed T/H circuit is proposed to improve the accuracy. Folding circuits are not only used in the fine converter but also in the coarse one and in the bit synchronization block to reduce the number of comparators for low power. This ADC is implemented in 0.5μm CMOS technology and occupies a die area of 2 × 1.5 mm~2. The measured differential nonlinearity and integral nonlinearity are 0.6 LSB/-0.8 LSB and 0.9 LSB/-1.2 LSB, respectively. The ADC exhibits 44.3 dB of signal-to-noise plus distortion ratio and 53.5 dB of spurious-free dynamic range for 1 MHz input sine-wave. The power dissipation is 138 mW at a sampling rate of 125 MHz at a 5 V supply.     

一个59mW 10位40MHz流水线A/D转换器

设计了一个工作在3.0V的10位40MHz流水线A/D转换器,采用了时分复用运算放大器,低功耗的增益自举telescopic运放,低功耗动态比较器,器件尺寸逐级减小优化功耗.在40MHz的采样时钟,0.5MHz的输入信号的情况下测试,可获得8.1位有效精度,最大积分非线性为2.2LSB,最大微分非线性为0.85LSB,电路用0.25μm CMOS工艺实现,面积为1.24mm2,功耗仅为59mW,其中同时包括为A/D转换器提供基准电压和电流的一个带隙基准源和缓冲电路.     

A 12-bit 10-MS/s SAR ADC with a weighted sampling time technique applied to C-DAC

This paper presents a low power 12-bit 10-MS/s successive approximation register (SAR) analog-to-digital convert (ADC) for bio-signal signal processing in wearable sensor systems. A weighted sampling time technique applied to a capacitor digital to analog converter (C-DAC) is employed to reduce the power consumption of the conventional SAR ADC with minimum performance sacrifice. The proposed technique helped reduce its energy consumed by MSB, MSB-1, MSB-6, and MSB-7 capacitors by more than 40% compared with that of the conventional C-DAC. Another technique, a voltage scaling method is also employed to lower the power supply voltage from 1.2 to 0.6 V for all the digital logics except the output registers, such that it results in a power reduction of 70%. The proposed ADC is implemented with the standard CMOS 65 nm 1-poly 6-metal n-well process. The ADC achieves DNL/INL of?±?1.2LSB/?±?1.5LSB, ENOB of 10.3-b, power consumption of 31.2 μW, and Walden FoM of 2.7fJ/step.

     

A 0.5-V 1-/spl mu/W successive approximation ADC

A successive approximation analog-to-digital converter (ADC) is presented operating at ultralow supply voltages. The circuit is realized in a 0.18-/spl mu/m standard CMOS technology. Neither low-V/sub T/ devices nor voltage boosting techniques are used. All voltage levels are between supply voltage V/sub DD/ and ground V/sub SS/. A passive sample-and-hold stage and a capacitor-based digital-to-analog converter are used to avoid application of operational amplifiers, since opamp operation requires higher values for the lowest possible supply voltage. The ADC has signal-to-noise-and-distortion ratios of 51.2 and 43.3 dB for supply voltages of 1 and 0.5 V, at sampling rates of 150 and 4.1 kS/s and power consumptions of 30 and 0.85 /spl mu/W, respectively. Proper operation is achieved down to a supply voltage of 0.4 V.     

An 8-bit 100-MS/s pipelined ADC without dedicated sample-and-hold amplifier

An 8-b 100-MS/s pipelined analog-to-digital converter(ADC) is presented.Without the dedicated sample-and -hold amplifier(SHA),it achieves figure-of-merit and area 21%and 12%less than the conventional ADC with the dedicated SHA,respectively.The closed-loop bandwidth of op amps in multiplying DAC is modeled,providing guidelines for power optimization.The theory is well supported by transistor level simulations.A 0.18-μm 1P6M CMOS process was used to integrate the ADCs,and the measured results show that the...