共查询到20条相似文献，搜索用时 46 毫秒
1.
Wind tunnel experiments examined the coupled effects of relative humidity (RH) and surface and particle properties on aerodynamically induced resuspension. Hydrophilic glass spheres and hydrophobic polyethylene spheres ～20 μm in diameter, with nanoscale surface features, were resuspended from hydrophilic glass, hydrophobic chemical agent resistant coating (CARC), and gold surfaces. Roughness of the glass and gold surfaces was on the nanoscale, whereas CARC surfaces had microscale roughness. Different particle–surface combinations yielded van der Waals interactions that varied by a factor of 4, but these differences had a relatively minor effect on resuspension. Wind tunnel RH was varied between 7% and 78%. Overall, RH affected the resuspension of hydrophilic particles on hydrophilic surfaces most strongly and that of hydrophobic particles on hydrophobic surfaces the least. For each particle–surface combination there was a threshold RH value below which resuspension rates were essentially constant and in good agreement with a dimensionless model of particle resuspension. Copyright © 2016 American Association for Aerosol Research 相似文献
2.
Electrified jets are applied industrially in agriculture, automobiles, targeted drug delivery systems, spacecraft propulsion units, liquid metal sprayers, ion sources, emulsifiers, dust scavenging systems, and ink-jet printers. Electrified columnar jets experience instability caused by electrohydrodynamic interactions of the charged liquid surfaces with electric fields. Electrostatic and surface tension forces competing along the liquid surface create surface pressure differences. The temporal rise and fall of the surface pressure induce oscillations of jets and droplet. A linear theory was derived to yield a dispersion equation determining the most dominant wavelength of oscillation for a given charge level and electric field; this enabled the estimation of the diameter of an atomized droplet. In addition, the frequency of oscillation was derived for a cylindrical jet and spherical droplet. Parametric studies were performed for various charging levels and electric field strengths. © 2018 American Association for Aerosol Research 相似文献
3.
Surface cleaning using air jets is an appropriate method to remove particles from surfaces especially when cleaning by mechanical methods is not suitable. The detachment behavior of droplets using an air jet is not necessarily the same as solid particles and there is a lack of studies regarding this behavior. In this article, the detachment of droplets on a plastic substrate by air jet impingement was investigated experimentally. Droplets of two different size ranges were impinged by an air jet with different impinging angles. For micrometer-sized droplets, a smaller horizontal velocity was required to detach large droplets. Moreover, the horizontal velocity required to detach 50% number fraction of droplets decreased when the air jet impinging angle increased. Millimeter-sized droplets split into many portions. Most portions remained on the substrate and only a few were resuspended. The remaining portions were distributed in a fan shape, with larger droplets traveling further on the substrate. A linear lower bound of traveled distance was observed. Due to the splitting and the small fraction of resuspension, it should not be expected that air jet cleaning of droplets is the same as that for solid particles. Copyright © 2017 American Association for Aerosol Research 相似文献
4.
Adhesion between dust particles and indoor surfaces can lead to negative effects on human health by triggering allergic and asthmatic reactions. In this study, adhesion forces of indoor office dust and activated carbon (AC, as model soot) particles to four common indoor materials (Al, Cu, PVC, and glass) were measured by colloidal probe atomic force microscopy. Chemical analysis of office dust shows it is largely made up of oxygenated hydrophilic organic carbon material. Both metal surfaces experienced weaker dust and AC adhesion than PVC or glass by up to 2–12 times lower primarily due to the presence of attractive electrostatic forces in the latter two (non-conducting) surfaces. Dust and AC adhesion were also highly sensitive to surface roughness, with an inverse relationship between adhesion force and roughness due to the reduction in contact area between the particle and a rougher material surface. Capillary forces play only a minor or negligible role in dust and AC surface adhesion. Adhesion models utilizing a purely van der Waals approach such as the simple Hamaker model and modified Rumpf's model are insufficient to determine the actual particle-surface contact radii and requires the accounting of non-van der Waals forces to adhesion. Copyright 2014 American Association for Aerosol Research 相似文献
5.
Particles deposited on a free-fall charged droplet were experimentally studied. A droplet, charged under 40% Rayleigh limit, fell through the particle chamber to capture particles by electrostatic attractions. The velocity of the droplet was smaller than 2.1 m/s. The particle-laden droplet eventually spread on a glass slide, which was further analyzed using optical microscope. It was found that the equivalent number of particles captured by the charged droplet were larger than that of uncharged ones by one order of magnitude at least. Remarkably, particles on the charged droplet agglomerated into a large cluster, which indicates that the agglomerated cluster can be actively precipitated due to the gravity force if the droplet completely evaporates. The front side of the charged droplet was the predominant region to capture the particles. However, the actual area of capture was smaller than hemispheric surface. Copyright © 2017 American Association for Aerosol Research 相似文献
6.
Cleanable dust filter media are typically used in huge baghouse filter apparatuses. Thereby, the regeneration by back-pulsing from the clean gas side is done by either time-controlled or pressure-controlled operation, whereas the latter is more common. Hence, the need for a detailed knowledge of the clogging and filtration mechanisms during long time operation of a pressure-controlled filter aging arises. A mathematical model describing the pressure drop evolution during time-controlled filter aging has been developed. The core of the developed model is the concept of dust masses that distribute themselves on a specific particle deposition area inside and on the surface of the filter medium. By altering this particle deposition area, various clogging mechanisms, occurring during an aging procedure, are covered by the model. In this work, the model was adapted and coefficient parameters adjusted for pressure-controlled filter regeneration operation. A multitude of pressure-controlled test runs were performed in a specially designed filtration apparatus. From these tests, process-specific parameters were regressed and used to model the respective pressure drop curves. These model pressure drop curves show good accordance both quantitatively and qualitatively to experimental data and give a detail view on different clogging mechanisms. 相似文献
7.
Dust aerosol and ice crystals are two major types of nonspherical particles in the atmosphere which have significant roles in cloud-aerosol interactions and the radiative budget. The presence of dust and ice often coincide in the atmosphere because dust particles are efficient ice nuclei. The size and composition dependence of the scattering properties of dust and ice are needed to assess their individual contributions to the optical scattering of sunlight. Here we present a new measurement technique used to determine the single particle forward scattering, backscattering, and depolarization ratio (at a wavelength of 680 nm) for representative nonspherical atmospheric particles. The Texas A&M University Continuous Flow Diffusion Chamber (CFDC) was used as an ice crystal generator to produce ice crystals via both homogenous and heterogeneous nucleation mechanisms under well-controlled laboratory conditions. Optical scattering properties of mineral dusts and small ice crystals (0.6 μm to 50 μm optical diameter) were measured by the Droplet Measurement Technologies, Inc. (DMT) Cloud Aerosol Spectrometer with Polarization (CASPOL). Significant differences between the optical properties of single dusts and ice particles of the same size were observed. Differences between the optical signatures of homogeneously and heterogeneously nucleated ice crystals were not statistically significant. Our results suggest that atmospheric ice crystals can be identified and quantified independently from the dust particles on which they form based on analysis of their backscatter and depolarization signals. Copyright 2014 American Association for Aerosol Research 相似文献
8.
Accurate exposure assessments are needed to evaluate health hazards caused by airborne microorganisms and require air samplers that efficiently capture representative samples. This highlights the need for samplers with well-defined performance characteristics. While generic aerosol performance measurements are fundamental to evaluate/compare samplers, the added complexity caused by the diversity of microorganisms, especially in combination with cultivation-based analysis methods, may render such measurements inadequate to assess suitability for bioaerosols. Specific performance measurements that take into account the end-to-end sampling process, targeted bioaerosol and analysis method could help guide selection of air samplers. Nine different samplers (impactors/impingers/cyclones/ electrostatic precipitators/filtration samplers) were subjected to comparative performance testing in this work. Their end-to-end cultivation-based biological sampling efficiencies (BSEs) and PCR-/microscopy-based physical sampling efficiencies (PSEs) relative to a reference sampler (BioSampler) were determined for gram-negative and gram-positive vegetative bacteria, bacterial spores, and viruses. Significant differences were revealed among the samplers and shown to depend on the bioaerosol's stress–sensitivity and particle size. Samplers employing dry collection had lower BSEs for stress-sensitive bioaerosols than wet collection methods, while nonfilter-based samplers showed reduced PSEs for 1 μm compared to 4 μm bioaerosols. Several samplers were shown to underestimate bioaerosol concentration levels relative to the BioSampler due to having lower sampling efficiencies, although they generally obtained samples that were more concentrated due to having higher concentration factors. Our work may help increase user awareness about important performance criteria for bioaerosol sampling, which could contribute to methodological harmonization/standardization and result in more reliable exposure assessments for airborne pathogens and other bioaerosols of interest. Copyright 2014 American Association for Aerosol Research 相似文献
10.
Particle resuspension could affect human exposure to particulate matter (PM) and serves as a potential route for infection transmission in indoor environments. A new resuspension model incorporating the effects of turbulent bursts, depletion of resuspendable particles, adhesion force distribution, and environmental relative humidity (RH) is proposed. In the proposed model, Monte Carlo simulation is used to model the occurrence of turbulent bursts and the depletion of resuspendable particles on surfaces. The adhesion force distribution and RH effects were included by employing the recently proposed adhesion force distribution model. Model validation is conducted by comparing model predictions against reported experimental data found in the literature. The effects of RH and particle size on resuspension are investigated using the proposed model. The threshold free stream velocity increases by two and three times when the RH increases from 36% to 61% and 67%, respectively. The threshold friction velocity decreases by five times when the particle size increases from 30.1 μm to 111 μm. The proposed model provides a physically reasonable framework for describing particle resuspension under turbulent flow. The capability of predicting the effect of RH greatly enhances the practical application of current resuspension models. Copyright 2014 American Association for Aerosol Research 相似文献
11.
The triboelectric charging of fungal spores was experimentally characterized during rebound and resuspension. A fungal spore source strength tester (FSSST) was used as a primary aerosol generator for spores of three fungal species and two powders (silicon carbide and silver). The critical velocity of rebound was determined using a variable nozzle area impactor (VNAI), and the charging state of particles after resuspension and rebound was measured using the FSSST, different impactor setups, electrometers, and optical particle counters. In the impactor setups and the FSSST, five different surface materials relevant for indoor environments were used (steel, glass, polystyrene, paper, and polytetrafluoroethylene). The critical velocity of rebound was determined to be 0.57 m/s for fungal spores, which is relatively low compared to silicon carbide and previous results for micron-sized aerosol particles. Based on the rebound impactor measurements, we were able to define the crucial parameters of charge transfer for different particle–surface material pairs. A contact charge parameter, which describes the triboelectric charging during rebound, was found to have a negative correlation with the charging state of the particles after the resuspension from an impactor. This connects the triboelectric charging during rebound and resuspension to each other. Based on the contact charge parameter values, quantified triboelectric series could be formed. The results of this work show that fungal spores can be charged both positively and negatively during rebound and resuspension depending on the fungal species and surface material. Copyright © 2016 American Association for Aerosol Research 相似文献
12.
It is currently admitted that for each filtration process using pleated filters, at least three steps can be distinguished: depth and surface filtration, which are common to flat filters, and surface reduction. This step is caused by inefficient filling of the pleat due to the filter geometry. For combustion aerosol, it has been proved that this third step strongly depends on the filtration velocity resulting in an increase of the resistance when air flow decreases. This observation leads one to think that Brownian diffusion, higher for low velocities, could influence the clogging dynamic of a pleated filter. In this article, a protocol derived from the dust cake preparation method published by Schmidt is developed. The aim of this study is to measure the aerosol penetration inside a filter media as well as in a pleat using a scanning electronic microscope and energy dispersive X-ray spectroscopy elementary detection. This method has also been extended to the study of pleated filters to measure the particle distribution inside the pleat. Filters were loaded with nanoparticles in order to evaluate the specificity of the diffusional regime on the clogging of pleated HEPA filters. For pleated filters, two filtration velocities were investigated: 2.5 and 0.2 cm/s. Copyright 2014 American Association for Aerosol Research 相似文献
13.
The dust loading has a significant influence on the transient performance of air filters. This study developed two models based on the Lagrangian and Eulerian methods to simulate the unsteady filtration process in the pleated filter. The flow field through the filter was calculated by solving the Navier-Stokes equation with the DES-SA turbulence model. The filter media and the cake layer were modeled as the porous zone. The Lagrangian method tracked the particle trajectories to model the particle motion, but the Eulerian model treated the particle as continuous phase. Two cell models were proposed to simulate the transient particle deposition and the cake layer growth on the filter medium surface for the Lagrangian and Eulerian methods, respectively. The simulated results were validated by the available experimental data. Both of the methods could provide relative accurate results with acceptable error. But the computing speed of Eulerian model was faster than the Lagrangian method. Otherwise, the new developed Eulerian model was used to investigate the effect of dust loading on the optimal design of pleated filter. © 2016 American Association for Aerosol Research 相似文献
14.
Many well-established models can be applied to calculate the filtration efficiencies. In these models the filtration velocity and challenging particle size are assumed to be known accurately. However, in realistic filtration tests, the filtration velocity has profiles dependent on the filter holder geometry and experimental conditions; the challenging particles have size distributions dependent on the instruments and operation conditions. These factors can potentially affect the measured filtration efficiency and lead to discrepancies with the models. This study aims to develop an integrative model to predict the filtration efficiencies in realistic tests by incorporating the effects of the filtration velocity profile and challenging particle size distribution classified by a differential mobility analyzer (DMA) into the existing filtration models. Face velocity profile is modeled with fluid mechanics simulations; the initial generated particle size distribution, the particle charging status and the DMA transfer function are modeled to obtain the challenging particle size distribution. These results are then fed into the filtration models. Simulated results are compared with experimental ones to verify the model accuracy. This model can be used to reduce filtration test artifacts and to improve the experimental procedure. The results reveal that the face velocity upstream the filter exhibits high degree of homogeneity not affecting the filtration efficiency if the filter pressure drop is not very low. The generated particle size distribution and the DMA selection size window could influence the challenging particle size distribution and therefore the measured filtration efficiency. Copyright © 2017 American Association for Aerosol Research 相似文献
15.
The characteristics of fugitive dust emitted from vehicles traveling on unpaved dirt roads were measured using a suite of instruments including a real-time fugitive dust sampler. The fugitive dust sampler is formed from a combination of a large particle inlet and an optical particle spectrometer that reports particle sizes from 6 to 75 µm. The large particle inlet permits the sampling of particles up to 75 µm with only a moderate dependence of sampling efficiency on wind-speed. Measurements made with the sampler showed that particles as large as ～50 µm were suspended from vehicular movement on the dirt roads, with the mode of the fugitive dust particle number size distribution ～2 µm, while the mass distribution mode was ～7 µm. A comparison of the fugitive dust sampler measurements with those made using standard PM instruments showed that the conventional instruments have a wind-direction bias that can result in under-sampling of large particles. The current measurements suggest that particles suspended from dirt roadways are of importance for local air quality within the near-road environment. Copyright © 2017 American Association for Aerosol Research 相似文献
16.
Occupational exposure to nanomaterial aerosols poses potential health risks to workers at nanotechnology workplaces. Understanding the mechanical stability of airborne nanoparticle agglomerates under varied mechanical forces and environmental conditions is important for estimating their emission potential and the released particle size distributions, which in consequence alters their transport and human uptake probability. In this study, two aerosolization and deagglomeration systems were used to investigate the potential for deagglomeration of nanopowder aerosols with different surface hydrophilicity under a range of shear forces and relative humidity conditions. Critical orifices were employed to subject airborne agglomerates to the shear forces induced by a pressure drop. Increasing applied pressure drop was found to be associated with decreased mean particle size and increased particle number concentrations. Rising humidity decreased the deagglomeration tendency as expressed by larger modal particle sizes and lower number concentrations compared to dry conditions. Hydrophilic aerosols exhibited higher sensitivities to changes in humidity than hydrophobic particles. However, the test systems themselves also differed in generated particle number concentrations and size distributions, which in turn altered the responses of created aerosols to humidity changes. The results of the present study clearly demonstrate that (a) humidity control is essential for dustiness and deagglomeration testing, (b) that (industrial) deagglomeration, for example, for preparation of aerosol suspensions, can be manipulated by subjecting airborne particles to external energies, and (c) that the humidity of workplace air may be relevant when assessing occupational exposure to nanomaterial aerosols. Copyright © 2016 American Association for Aerosol Research 相似文献
17.
A new sampling approach has been developed to enable affordable, time-resolved monitoring of particulate chemical composition, and more generally to provide concentrated samples of airborne particles. Using a newly developed, moderated water-based condensational growth technology, individual particle samples are deposited in a 1-mm diameter dry “spot.” The moderated condensation technology enables this collection with minimal temperature rise, providing robust collection for volatile constituents. Measured collection efficiencies are above 95% for particles in the size range from 0.010 μm to 2.5 μm. A set of 20 or more time-resolved samples, plus blanks, may be collected onto a multiwell collection plate. For chemical analysis the plate is returned to the laboratory, and placed directly into a modified autosampler, without extraction or preparation. The autosampler handles the addition of eluent, extraction, and sample injection without user manipulation. This article presents the design and laboratory evaluation of a 1.5 L/min sampling rate version of this system. Copyright 2014 American Association for Aerosol Research 相似文献
18.
The estimation of air velocity distributions and particle trajectories is inevitable to analyse the mechanism of classification, but the direct measurement of il is extremely difficult. The authors, here report three dimensional air velocity distributions within the inside drum of model Sturtevant-type air classifier measured by a spherical five-holed Pitot-lube, and also two dimensional particle ejecting velocities on a model distributor determined by photography. Using those results, the cut size calculated from particle trajectories in the classifier is compared with the experimental results and theoretical values. 相似文献
19.
This article presents analytical and experimental results for the velocity distribution and transport of expiratory particles from an artificial cough. The stream-wise penetration distance and velocity field of the cough jet were determined through a combination of dimensionless analysis and experimental techniques. The experiments were conducted in a well-controlled environmental chamber with simplified thermal manikins to simulate human coughs and buoyant thermal plumes, and involved flow visualization, velocity measurements employing high and low velocity hot-wire anemometers, and particle size and concentration measurement. The study analyzed three particle sizes—0.77, 2.5, and 7 μm—to examine the impact of particle size on particle transport in the cough jet region and in the vicinity of a receiver occupant positioned in close proximity to the coughing source. The results indicate that the cough jet has a lower axial velocity but higher span-wise expansion rate than a steady jet with an identical discharge velocity. The particles of three sizes have a similar trajectory when considering the transport in the cough jet region. However, particle concentration distributions of the three size particles show that size is an important factor for particle transport in the vicinity of the receiver occupant where airflow velocity decays to the room background air velocity. Furthermore, the results suggest that a cough jet is able to overcome the buoyant human thermal plume and travel further ahead in the region behind the receiver occupant. Copyright 2014 American Association for Aerosol Research 相似文献
20.
The purpose of this study was to compare the performance efficiency of melt-blown and currently used glass fiber filter media under the same environmental conditions. To evaluate filter efficiency, filter class was determined according to ISO and European standards (EN 1822-1:2009) using an automated filter tester (0.3 μm size), taking into account particle filtration, fractional efficiency for negative pressure devices, and consumption of electrical power. The average fractional efficiency, quality factor (QF), fractional efficiency by dust loading amount, pressure by dust loading amount, and QF by dust loading amount were higher in the case of melt-blown media than in the case of glass fiber filters. The fractional efficiency of hydrocharged melt-blown filters was higher than that of uncharged media. Based on performance efficiency, melt-blown filters are more effective high efficiency particulate air filters than glass fiber media. Copyright © 2018 American Association for Aerosol Research 相似文献
|
