Validation of AMSR-E soil moisture using L-band airborne radiometer data from National Airborne Field Experiment 2006

AMSR-E has been extensively evaluated under a wide range of ground and climate conditions using in situ and aircraft data, where the latter were primarily used for assessing the T_B calibration accuracy. However, none of the previous work evaluates AMSR-E performance under the conditions of flood irrigation or other forms of standing water. Also, it should be mentioned that global soil moisture retrievals from AMSR-E typically utilize X-band data. Here, C-band based AMSR-E soil moisture estimates are evaluated using 1 km resolution retrievals derived from L-band aircraft data collected during the National Airborne Field Experiment (NAFE'06) field campaign in November 2006. NAFE'06 was conducted in the Murrumbidgee catchment area in southeastern Australia, which offers diverse ground conditions, including extensive areas with dryland, irrigation, and rice fields. The data allowed us to examine the impact of irrigation and standing water on the accuracy of satellite-derived soil moisture estimates from AMSR-E using passive microwave remote sensing. It was expected that in fields with standing water, the satellite estimates would have a lower accuracy as compared to soil moisture values over the rest of the domain. Results showed sensitivity of the AMSR-E to changes in soil moisture caused by both precipitation and irrigation, as well as good spatial (average R = 0.92 and RMSD = 0.049 m³/m³) and temporal (R = 0.94 and RMSD = 0.04 m³/m³) agreement between the satellite and aircraft soil moisture retrievals; however, under the NAFE'06 ground conditions, the satellite retrievals consistently overestimated the soil moisture conditions compared to the aircraft.     

Aircraft based soil moisture retrievals under mixed vegetation and topographic conditions

An unresolved issue in global soil moisture retrieval using passive microwave sensors is the spatial integration of heterogeneous landscape features to the nominal 50 km footprint observed by most low frequency satellite systems. One of the objectives of the Soil Moisture Experiments 2004 (SMEX04) was to address some aspects of this problem, specifically variability introduced by vegetation, topography and convective precipitation. Other goals included supporting the development of soil moisture data sets that would contribute to understanding the role of the land surface in the concurrent North American Monsoon System. SMEX04 was conducted over two regions: Arizona — semi-arid climate with sparse vegetation and moderate topography, and Sonora (Mexico) — moderate vegetation with strong topographic gradients. The Polarimetric Scanning Radiometer (PSR/CX) was flown on a Naval Research Lab P-3B aircraft as part of SMEX04 (10 dates of coverage over Arizona and 11 over Sonora). Radio Frequency Interference (RFI) was observed in both PSR and satellite-based (AMSR-E) observations at 6.92 GHz over Arizona, but no detectable RFI was observed over the Sonora domain. The PSR estimated soil moisture was in agreement with the ground-based estimates of soil moisture over both domains. The estimated error over the Sonora domain (SEE = 0.021 cm³/cm³) was higher than over the Arizona domain (SEE = 0.014 cm³/cm³). These results show the possibility of estimating soil moisture in areas of moderate and heterogeneous vegetation and high topographic variability.     

Multi-sensor model-data fusion for estimation of hydrologic and energy flux parameters

Model-data fusion offers considerable promise in remote sensing for improved state and parameter estimation particularly when applied to multi-sensor image products. This paper demonstrates the application of a ‘multiple constraints’ model-data fusion (MCMDF) scheme to integrating AMSR-E soil moisture content (SMC) and MODIS land surface temperature (LST) data products with a coupled biophysical model of surface moisture and energy budgets for savannas of northern Australia. The focus in this paper is on the methods, difficulties and error sources encountered in developing an MCMDF scheme and enhancements for future schemes. An important aspect of the MCMDF approach emphasized here is the identification of inconsistencies between model and data, and among data sets.The MCMDF scheme was able to identify that an inconsistency existed between AMSR-E SMC and LST data when combined with the coupled SEB-MRT model. For the example presented, an optimal fit to both remote sensing data sets together resulted in an 84% increase in predicted SMC and 0.06% increase for LST relative to the fit to each data set separately. That is the model predicted on average cooler LST's (∼ 1.7 K) and wetter SMC values (∼ 0.04 g cm^− 3) than the satellite image products. In this instance we found that the AMSR-E SMC data on their own were poor constraints on the model. Incorporating LST data via the MCMDF scheme ameliorated deficiencies in the SMC data and resulted in enhanced characterization of the land surface soil moisture and energy balance based on comparison with the MODIS evapotranspiration (ET) product of Mu et al. [Mu, Q., Heinsch, F.A, Zhao, M. and Running, S.W. (in press), Development of a global evapotranspiration algorithm based on MODIS and global meteorology data, Remote Sensing of Environment.]. Canopy conductance, g_C, and latent heat flux, λE, from the MODIS ET product were in good agreement with RMSEs for g_C = 0.5 mm s^− 1 and for λE = 18 W m^− 2, respectively. Differences were attributable to a greater canopy-to-air vapor pressure gradient in the MCMDF approach obtained from a more realistic partitioning of soil surface and canopy temperatures.     

Soil moisture retrieval using thermal inertia, determined with visible and thermal spaceborne data, validated for European forests

Variations in soil moisture strongly affect surface energy balances, regional runoff, land erosion and vegetation productivity (potential crop yield). Hence, the detection of soil moisture content (SMC) is very valuable in the social, economic, humanitarian (food security) and environmental segments of society. A method to estimate SMC from optical and thermal spectral information of METEOSAT imagery based on thermal inertia (TI) is presented. Minimum and maximum TI values from time series are combined in the Soil Moisture Saturation Index (SMSI). To convert surface to soil profile values, a Markov type filter is used, based on a simple two layer water balance equation (the surface layer and the reservoir below) and an autocorrelation function. Ten-daily SMC values are compared with up-scaled (using AVHRR/NDVI) observations on 10 EUROFLUX sites in Europe for the 1997 growing season (March-October). Moreover, the thermal inertia approach is compared for 1997, with ERS Scatterometer data for eight EUROFLUX sites. METEOSAT pixels are up-scaled to accommodate the ERS Scatterometer spatial resolution. The regression coefficients (slope, intercept and R²) of the thermal inertia approach versus the up-scaled soil moisture observations from EUROFLUX sites vary between 0.811-1.148, − 0.0029-0.66 and 0.544-0.877, respectively, with a RRMSE range of 3.9% to 35.7%. The regression coefficients of the comparison of ERS Scatterometer derived Soil Water Index (SWI) versus the up-scaled Soil Moisture Saturation Index for the pooled case (binning the eight EUROFLUX sites) are 0.587, 0.105 and 0.441, respectively, with a RRMSE of 38%. A simple error propagation model applied for the thermal inertia approach reveals that the absolute and relative errors of the obtained soil moisture content is at least 0.010 m³ m^− 3 or 2.0% with a SMC of 0.203 m³ m^− 3. Recommendations are made to test and implement the TI methodology using NOAA/AVHRR imagery.     

Comparing the utility of microwave and thermal remote-sensing constraints in two-source energy balance modeling over an agricultural landscape

A two-source (soil + vegetation) energy balance model using microwave-derived near-surface soil moisture as a key boundary condition (TSM_SM) and another scheme using thermal-infrared (radiometric) surface temperature (TSM_TH) were applied to remote sensing data collected over a corn and soybean production region in central Iowa during the Soil Moisture Atmosphere Coupling Experiment (SMACEX)/Soil Moisture Experiment of 2002 (SMEX02). The TSM_SM was run using fields of near-surface soil moisture from microwave imagery collected by aircraft on six days during the experiment, yielding a root mean square difference (RMSD) between model estimates and tower measurements of net radiation (Rn) and soil heat flux (G) of approximately 20 W m^− 2, and 45 W m^− 2 for sensible (H) and latent heating (LE). Similar results for H and LE were obtained at landscape/regional scales when comparing model output with transect-average aircraft flux measurements. Flux predictions from the TSM_SM and TSM_TH models were compared for two days when both airborne microwave-derived soil moisture and radiometric surface temperature (T_R) data from Landsat were available. These two days represented contrasting conditions of moderate crop cover/dry soil surface and dense crop cover/moist soil surface. Surface temperature diagnosed by the TSM_SM was also compared directly to the remotely sensed T_R fields as an additional means of model validation. The TSM_SM performed well under moderate crop cover/dry soil surface conditions, but yielded larger discrepancies with observed heat fluxes and T_R under the high crop cover/moist soil surface conditions. Flux predictions from the thermal-based two-source model typically showed biases of opposite sign, suggesting that an average of the flux output from both modeling schemes may improve overall accuracy in flux predictions, in effect incorporating multiple remote-sensing constraints on canopy and soil fluxes.     

Evaluation of soil moisture from satellite observations over South America

A study was performed to evaluate the surface soil moisture derived from Advanced Microwave Scanning Radiometer for the Earth Observing System (AMSR-E) sensor observations over South America. Other soil moisture and rainfall datasets were also used for the analysis. The information for the soil data came from the Eta regional climate model, and for the rainfall data from the Tropical Rainfall Microwave Mission (TRMM) satellite. Statistical analysis was used to evaluate the quality of the soil moisture and rainfall products, with estimates of the correlation coefficient (R), χ² and Cramer's phi (?_c). The results show high correlations (R > 0.8) of the AMSR-E soil moisture products with the Eta model for different regions of South America. Comparison of soil moisture products with rainfall datasets showed that the AMSR-E C-band soil moisture product was highly correlated with the TRMM satellite rainfall datasets, with the highest values of χ² and ?. The results show that the AMSR-E C-band soil moisture products contain important information that can be used for various purposes, such as monitoring floods or droughts in arid areas or as input within the framework of an assimilation scheme of numerical weather prediction models.     

Quantifying the spatial distribution of soil mass wasting processes after the 2008 earthquake in Wenchuan, China: A case study of the Longmenshan area

The beautiful Longmenshan area is one of the main tourist attractions in Sichuan Province, China. The epicenter of a catastrophic earthquake measured at 8.0 Ms (China Seismological Bureau), occurred within this area at Wenchuan (31°01′16″N, 103°22′01″E) at 14:28 May 12, 2008 (Beijing time). The earthquake triggered numerous types of landslide transport and hazards, including soil and debris avalanches, rockfalls, slumps, debris flows, creation of barrier lakes and slope flattenings. This paper examines the landslide hazards in the Longmenshan area caused by the earthquake using remotely sensed images, mainly Beijing-1 Microsatellite data before and after the earthquake, compared to digital elevation maps and slope gradient maps, land use and vegetation cover maps. Areas of erosion and loss of vegetation were compared from pre- and post-earthquake data, from which were calculated changes in vegetated areas, bare slopes, and mass movement during the earthquake. These events occurred over altitudes from 1000 to 4000 m and on slope angles between 25 and 55°. The results show that the total area of erosion and land movement due to the earthquake increased by 86.3 km² (19.2% of the study area). Compared with pre-earthquake, the areas of very low intensity soil erosion and moderate intensity soil erosion were respectively reduced by 3.6 km², 24.3 km² and 30.9 km². On the other hand, the areas of severe and very severe intensity soil erosion were substantially increased by 45.8 km² and 99.2 km². In the post-earthquake stage, the bare areas (vegetation cover < 15%) have increased by 65.8 km². Without vegetation, the denuded earthquake damaged slopes and other high risk sites have become severe erosion problems. Thus, it is essential to continue long-term monitoring of mass wasting in the denuded areas and evaluate potential risk sites for future landslides and debris flows. We anticipate that these results will be helpful in decision making and policy planning for recovery and reconstruction in the earthquake-affected area.     

Effects of corn on C- and L-band radar backscatter: A correction method for soil moisture retrieval

This paper discusses the effects of vegetation on C- (4.75 GHz) and L- (1.6 GHz) band backscattering (σ^o) measured throughout a growth cycle at incidence angles of 15, 35 and 55°. The utilized σ^o data set was collected by a truck mounted scatterometer over a corn field and is supported by a comprehensive set of ground measurements, including soil moisture and vegetation biomass. Comparison of σ^o measurement against simulations by the Integral Equation Method (IEM) surface scattering model (Fung et al., 1992) shows that the σ^o measurements are dominated either by an attenuated soil return or by scattering from vegetation depending on the antenna configuration and growth stage. Further, the measured σ^o is found to be sensitive to soil moisture even at peak biomass and large incidence angles, which is attributed to scattering along the soil-vegetation pathway.For the simulation of C-band σ^o and the retrieval of soil moisture two methods have been applied, which are the semi-empirical water cloud model (Attema & Ulaby, 1978) and a novel method. This alternative method uses the empirical relationships between the vegetation water content (W) and the ratio of the bare soil and the measured σ^o to correct for vegetation. It is found that this alternative method is superior in reproducing the measured σ^o as well as retrieving soil moisture. The highest retrieval accuracies are obtained at a 35° incidence angle leading to RMSD's of 0.044 and 0.037 m³ m^− 3 for the HH and VV-polarization, respectively. In addition, the sensitivity of these soil moisture retrievals to W and surface roughness parameter uncertainties is investigated.     

Soil moisture mapping and AMSR-E validation using the PSR in SMEX02

Field experiments (SMEX02) were conducted to evaluate the effects of dense agricultural crop conditions on soil moisture retrieval using passive microwave remote sensing. Aircraft observations were collected using a new version of the Polarimetric Scanning Radiometer (PSR) that provided four C band and four X band frequencies. Observations were also available from the Aqua satellite Advanced Microwave Scanning Radiometer (AMSR-E) at these same frequencies. SMEX02 was conducted over a three-week period during the summer near Ames, Iowa. Corn and soybeans dominate the region. During the study period the corn was approaching its peak water content state and the soybeans were at the mid point of the growth cycle. Aircraft observations are compared to ground observations. Subsequently models are developed to describe the effects of corn and soybeans on soil moisture retrieval. Multiple altitude aircraft brightness temperatures were compared to AMSR-E observations to understand brightness temperature scaling and provide validation. The X-band observations from the two sensors were in reasonable agreement. The AMSR-E C-band observations were contaminated with anthropogenic RFI, which made comparison to the PSR invalid. Aircraft data along with ancillary data were used in a retrieval algorithm to map soil moisture. The PSR estimated soil moisture retrievals on a field-by-field comparison had a standard error of estimate (SEE) of 5.5%. The error reduced when high altitude soil moisture estimates were aggregated to 25 km resolution (same as AMSR-E EASE grid product resolution) (SEE ∼ 2.85%). These soil moisture products provide a validation of the AMSR retrievals. PSR/CX soil moisture images show spatial and temporal patterns consistent with meteorological and soil conditions. The dynamic range of the PSR/CX observations indicates that reasonable soil moisture estimates can be obtained from AMSR, even in areas of high vegetation biomass content (∼ 4-8 kg/m2).     

ASCAT soil wetness index validation through in situ and modeled soil moisture data in central Italy

Reliable measurements of soil moisture at global scale might greatly improve many practical issues in hydrology, meteorology, climatology or agriculture such as water management, quantitative precipitation forecasting, irrigation scheduling, etc. Remote sensing offers the unique capability to monitor soil moisture over large areas but, nowadays, the spatio-temporal resolution and accuracy required for some hydrological applications (e.g., flood forecasting in medium to large basins) have still to be met. The Advanced SCATterometer (ASCAT) onboard the Metop satellite (VV polarization, C-band at 5.255 GHz), based on a large extent on the heritage of the ERS scatterometer, provides a soil moisture product available at a coarse spatial resolution (25 km and 50 km) and at a nearly daily time step. This study evaluates the accuracy of the new 25 km ASCAT derived saturation degree product by using in situ observations and the outcomes of a soil water balance model for three sites located in an inland region of central Italy. The comparison is carried out for a 2-year period (2007-2008) and three products derived from ASCAT: the surface saturation degree, m_s, the exponentially filtered soil wetness index, SWI, and its linear transformation, SWI*, matching the range of variability of ground data. Overall, the performance of the three products is found to be quite good with correlation coefficients higher than 0.92 and 0.80 when the SWI is compared with in situ and simulated saturation degree, respectively. Considering SWI*, the root mean square error is less than 0.035 m³/m³ and 0.042 m³/m³ for in situ and simulated saturation degree, respectively. More notably, when the m_s product is compared with modeled data at 3 cm depth, this index is found able to accurately reproduce the temporal pattern of the simulated saturation degree in terms of both timing and entity of its variations also at fine temporal scale. The daily temporal resolution and the reliability obtained with the ASCAT derived saturation degree products represent the preliminary step for its effective use in operational rainfall-runoff modeling.     

The use of a microwave backscatter model for retrieving soil moisture over bare soil

Abstract

Most attempts at predicting soil moisture from C-band microwave backscattering coefficients for bare soil are made by fitting experimental calibration relations obtained for limited ranges of incidence angle and soil surface roughness. In this paper, a more general approach is discussed using an inversion procedure to extend the use of a single experimental calibration relation to a wider range of incidence angle and surface roughness. A correcting function is proposed to normalize the backscattering coefficients to the conditions (incidence angle and surface roughness) of the calibration relation. This correcting function was derived from simulated data using the physical optics or KirchhofTs scatter model using the scalar approximation. Before discussing the inversion procedure, the backscattering coefficients calculated by the model have been compared with experimental data measured in the C-band, HH polarization and three incidence angles (Θ= 15°, 23°, 50°) under a wide range of surface soil moisture conditions (0.02H_v  0.35cm³ cm^-3) and for a single quite smooth soil surface roughness (0–011 _s  OOI4/n)m. The model was found to be experimentally validated from 15° to 23° of incidence and for surface soil moistures higher than 0-I0cm³cm^-3. For the inversion procedure, it is assumed to have a wider range of validity (15°  Θ 35° ) for ihc incidence angle. A sensitivity analysis of the model to errors on roughness parameter and incidence angle was performed in order to assess the feasability and suitability of the described inversion procedure.     

Intercomparison of microwave remote-sensing soil moisture data sets based on distributed eco-hydrological model simulation and in situ measurements over the North China Plain

Intercomparisons of microwave-based soil moisture products from active ASCAT (Advanced Scatterometer) and passive AMSR-E (Advanced Microwave Scanning Radiometer for the Earth Observing System) is conducted based on surface soil moisture (SSM) simulations from the eco-hydrological model, Vegetation Interface Processes (VIP), after it is carefully validated with in situ measurements over the North China Plain. Correlations with VIP SSM simulation are generally satisfactory with average values of 0.71 for ASCAT and 0.47 for AMSR-E during 2007–2009. ASCAT and AMSR-E present unbiased errors of 0.044 and 0.053 m³ m^?3 on average, with respect to model simulation. The empirical orthogonal functions (EOF) analysis results illustrate that AMSR-E provides more consistent SSM spatial structure with VIP than ASCAT; while ASCAT is more capable of capturing SSM temporal dynamics. This is supported by the facts that ASCAT has more consistent expansion coefficients corresponding to primary EOF mode with VIP (R = 0.825, p < 0.1). However, comparison based on SSM anomaly demonstrates that AMSR-E and ASCAT have similar skill in capturing SSM short-term variability. Temporal analysis of SSM anomaly time series shows that AMSR-E provides best performance in autumn, while ASCAT provides lower anomaly bias during highly-vegetated summer with vegetation optical depth of 0.61. Moreover, ASCAT retrieval accuracy is less influenced by vegetation cover, as it is in relatively better agreement with VIP simulation in forest than in other land-use types and exhibits smaller interannual fluctuation than AMSR-E. Identification of the error characteristics of these two microwave soil moisture data sets will be helpful for correctly interpreting the data products and also facilitate optimal specification of the error matrix in data assimilation at a regional scale.     

Derivation of pan-Arctic soil decomposition rate constant,heterotrophic respiration and NEE using AMSR-E and MODIS data

An approach was developed for regional assessment and monitoring of land-atmosphere carbon dioxide (CO₂) exchange, soil heterotrophic respiration (R _h), and vegetation productivity of Arctic tundra using global satellite remote sensing at optical and microwave wavelengths. C- and X-band brightness temperatures were used from the Advanced Microwave Scanning Radiometer Earth Observing System (AMSR-E) to extract surface wetness and temperature, and MODerate Resolution Imaging Spectroradiometer (MODIS) data were used to derive land cover, Leaf Area Index (LAI), and Net Primary Production (NPP) information. Calibration and validation activities involve comparisons between satellite remote sensing and tundra CO₂ eddy flux towers, and hydroecological process model simulations. Analyses of spatial and temporal anomalies and environmental drivers of land-atmosphere net CO₂ exchange at weekly and annual time steps were conducted. Surface soil moisture and temperature, as detected from satellite remote-sensing observations, were found to be major drivers for spatial and temporal patterns of tundra net ecosystem CO₂ exchange and photosynthetic and respiration processes. Satellite microwave measurements are capable of capturing seasonal variations and regional patterns in tundra soil heterotrophic respiration and CO₂ exchange, while the ability to extract spatial patterns at the scale of surface heterogeneity is limited by the coarse spatial scale of the satellite remote-sensing footprint. The microwave-derived surface temperature and soil moisture were used to estimate net ecosystem carbon exchange (NEE) at the boreal-Arctic region. These were validated using flux tower sites data. Existing satellite-based measurements of vegetation structure (i.e. LAI) and productivity (i.e. Gross Primary Production (GPP) and NPP) from the Aqua/Terra MODIS with the AMSR-E-derived land-surface temperature and soil moisture were used and integrated. Spatially explicit estimates of NEE for the pan-Arctic region at daily, weekly and annual intervals were derived. Comparative analysis of satellite data-derived NEE with measurements from CO₂ eddy flux tower sites and the BIOME-BGC model were carried out and good agreement was found. The comparative analysis is statistically significant with high regression (i.e. R ²?=?0.965), especially in the R _h calculation and the overall NEE regression is 0.478. The results also indicate that the carbon cycle response to climate change is nonlinear and is strongly coupled to Arctic surface hydrology.     

Generation of high-resolution East Antarctic landfast sea-ice maps from cloud-free MODIS satellite composite imagery

A method to generate high spatio-temporal resolution maps of landfast sea ice from cloud-free MODIS composite imagery is presented. Visible (summertime) and thermal infrared (wintertime) cloud-free 20-day MODIS composite images are used as the basis for these maps, augmented by AMSR-E ASI sea-ice concentration composite images (when MODIS composite image quality is insufficient). The success of this technique is dependent upon efficient cloud removal during the compositing process. Example wintertime maximum (~ 374,000 km²) and summertime minimum (~ 112,000 km²) fast-ice maps for the entire East Antarctic coast are presented. The summertime minimum map provides the first high-resolution indication of multi-year fast-ice extent, which may be used to help assess changes in Antarctic sea-ice volume. The 2σ errors in fast-ice extent are estimated to be ± 2.98% when ≥ 90% of the fast-ice pixels in a 20-day period are classified using the MODIS composite, or ± 8.76 otherwise (when augmenting AMSR-E or the previous/next MODIS composite image is used to classify > 10% of the fast ice). Imperfect composite image quality, caused by persistent cloud, inaccurate cloud masking or a highly dynamic fast-ice edge, was the biggest impediment to automating the fast-ice detection procedure.     

Continental-scale net radiation and evapotranspiration estimated using MODIS satellite observations

Evapotranspiration (ET) is a major pathway for water loss from many ecosystems, and its seasonal variation affects soil moisture and net ecosystem CO₂ exchange. We developed an algorithm to estimate ET using a semi-empirical Priestley-Taylor (PT) approach, which can be applied at a range of spatial scales. We estimated regional net radiation (R_net) at monthly time scales using MODerate resolution Imaging Spectroradiometer (MODIS) albedo and land surface temperature. Good agreement was found between satellite-based estimates of monthly R_net and field-measured R_net, with a RMSE of less than 30 W m^− 2. An adjustable PT coefficient was parameterized as a function of leaf area index and soil moisture based on observations from 27 AmeriFlux eddy covariance sites. The biome specific optimization using tower-based observations performed well, with a RMSE of 17 W m^− 2 and a correlation of 0.90 for predicted monthly latent heat. We implemented the approach within the hydrology module of the CASA biogeochemical model, and used it to estimate ET at a 1 km spatial resolution for the conterminous United States (CONUS). The RMSE of modeled ET was reduced to 21.1 mm mon^− 1, compared to 27.1 mm mon^− 1 in the original CASA model. The monthly ET rates averaged over the Mississippi River basin were similar to those derived using GRACE satellite measurements and river discharge data. ET varied substantially over the CONUS, with annual mean values of 110 ± 76 mm yr^− 1 in deserts, 391 ± 176 mm yr^− 1 in savannas and grasslands, and 840 ± 234 mm yr^− 1 in broadleaf forests. The PT coefficient was the main driver for the spatial variation of ET in arid areas, whereas R_net controlled ET when mean annual precipitation was higher than approximately 400 mm yr^− 1.     

A comparison study on empirical microwave soil moisture downscaling methods based on the integration of microwave-optical/IR data on the Tibetan Plateau

Soil moisture plays a vital role in land surface energy and the water cycle. Microwave remote sensing is widely used because of the physically based relationship between the land surface emission observed and soil moisture. However, the application of retrieved soil moisture data is restricted by its coarse spatial resolution. To overcome this weakness, downscaling methods should be developed to disaggregate coarse resolution microwave soil moisture data to fine resolution. The traditional method is the microwave-optical/IR synergistic approach, in which land surface temperature, vegetation index, and surface albedo are key parameters. Five purely empirical methods based on the triangle feature are selected in this study. To evaluate their performance on downscaling microwave soil moisture, these methods are applied to the Zoige Plateau in China using the Advanced Microwave Scanning Radiometer on the Earth Observing System (AMSR-E) Land Parameter Retrieval Model (LPRM) soil moisture product and Moderate Resolution Imaging Spectroradiometer (MODIS) optical/IR products. The coarse-resolution AMSR-E LPRM soil moisture data are disaggregated into the high resolution of the MODIS product, and the surface soil moisture measurements of the Maqu soil moisture observation network located in the plateau are used to validate the downscaling results. Results show that (1) the relationship models used in these methods can generally capture the variation in soil moisture, with R² around 0.6, but have a relatively high uncertainty under conditions of high soil moisture; (2) the methods can provide high-resolution soil moisture distribution, but the downscaled soil moisture presents a low level correlation with field measurements at different spatial and temporal scales. This comparative study provides insight into the performance of popular purely empirical downscaling methods on enhancing the spatial resolution of soil moisture on the Tibetan Plateau. Although synergistic methods can improve the spatial resolution of AMSR-E soil moisture data, additional studies are needed to exclude the uncertainty from AMSR-E soil moisture estimation, the low sensitivity of the relationship model under high soil moisture, and the spatial representativeness difference between coarse pixels and point measurement.     

A soil moisture assimilation scheme based on the microwave Land Emissivity Model and the Community Land Model

Applications of microwave remote-sensing data in land data assimilation are a topic of current interest and importance due to their high temporal and spatial resolution and availability. However, there have been few studies on land surface sub-grid scale heterogeneity and calculating microwave wetland surface emissivity when directly assimilating gridded Advanced Microwave Scanning Radiometer-Earth Observing System (AMSR-E) satellite brightness temperature (BT) data to estimate soil moisture. How to assimilate gridded AMSR-E BT data for land surface model (LSM) grid cells including various land cover types, especially wetland, is worthy of careful study. The ensemble Kalman filter (EnKF) method is able to resolve the non-linearity and discontinuity in forecast and observation operators, and is widely used in land data assimilation. In this study, considering the influences of land surface sub-grid scale heterogeneity, a satellite data simulation scheme based on the National Center for Atmosphere Research (NCAR) Community Land Model version 2.0 (CLM2.0), microwave Land Emissivity Model (LandEM), Shuffled Complex Evolution (SCE-UA) algorithm and AMSR-E BT observation data is presented to simulate AMSR-E BT data and calibrate microwave wetland surface emissivity; then, a soil moisture data assimilation scheme is developed to directly assimilate the gridded AMSR-E BT data, which consists of the CLM2.0, LandEM and EnKF. The experimental results indicate that the calibrated microwave wetland surface emissivities possess excellent transportability, and that the assimilation scheme is practical and can significantly improve soil moisture estimation accuracy. This study provides a promising solution to improve soil moisture estimation accuracy through directly assimilating gridded AMSR-E BT data for various land cover types such as bare soil, vegetation, snow, lake and wetland.     

Comparison of MODIS, eddy covariance determined and physiologically modelled gross primary production (GPP) in a Douglas-fir forest stand

Quantification of the magnitude of net terrestrial carbon (C) uptake, and how it varies inter-annually, is an important question with future potential sequestration influenced by both increased atmospheric CO₂ and changing climate. However the assessment of differences in measured and modeled C accumulation is a challenging task due to the significant fine scale variation occurring in terrestrial productivity due to soil, climate and vegetation characteristics as well as difficulties in measuring carbon accumulation over large spatial areas. The Moderate Resolution Imaging Spectroradiometer (MODIS) offers a means of monitoring gross primary production (GPP), both spatially and temporally, routinely from space. However it is critical to compare and contrast the temporal dynamics of the C and water fluxes with those measured from ground-based networks, or estimated using physiological models. In this paper, using a number of approaches, our objective is to determine if any systematic biases exists in either the MODIS, or the modeled estimates of fluxes, relative to the measurements made over an evergreen, needleleaf temperate rainforest on Vancouver Island, Canada. Results indicate that 8-day GPP as predicted with a simple physiological model (3PGS), forced using local meteorology and canopy characteristics, matched measured fluxes very well (r² = 0.86, p < 0.001) with no significant difference between eddy covariance (EC) and modeled GPP (p < 0.001). In addition, modeled water supply closely matched measured relative available soil water content at the site. Using canopy characteristics from the MODIS fraction of photosynthetically active radiation (fPAR) algorithm, slightly reduced the correspondence of the predictions due to a large number of unsuccessful retrievals (83%) due to sun angle, snow and cloud. Predictions of GPP based on the MODIS GPP algorithm, forced using local meteorology and canopy characteristics, were also highly correlated with EC measurements (r² = 0.89, p < 0.001) however these estimates were biased under predicting GPP. Estimates of GPP based on the most recent MODIS reprocessing (collection 4.5) remained highly correlated (r² = 0.88, p < 0.001) yet were also the most biased with the estimates being 30% less than the EC-measured GPP. Most of the variance in GPP at the site was explained by the absorbed photosynthetically active radiation. We also compared the nighttime respiration as measured over 2 years at the site with the minimum 8-day MODIS land surface temperature and found a significant relationship (r² = 0.57), similar to other studies.     

A first assessment of the SMOS data in southwestern France using in situ and airborne soil moisture estimates: The CAROLS airborne campaign

The Soil Moisture and Ocean Salinity (SMOS) satellite mission, based on an aperture synthesis L-band radiometer was successfully launched in November 2009. In the context of a validation campaign for the SMOS mission, intensive airborne and in situ observations were performed in southwestern France for the SMOS CAL/VAL, from April to May 2009 and from April to July 2010. The CAROLS (Cooperative Airborne Radiometer for Ocean and Land Studies) bi-angular (34°-0°) and dual-polarized (V and H) L-band radiometer was designed, built and installed on board the French ATR-42 research aircraft. During springs of 2009 and 2010, soil moisture observations from the SMOSMANIA (Soil Moisture Observing System-Meteorological Automatic Network Integrated Application) network of Météo-France were complemented by airborne observations of the CAROLS L-band radiometer, following an Atlantic-Mediterranean transect in southwestern France. Additionally to the 12 stations of the SMOSMANIA soil moisture network, in situ measurements were collected in three specific sites within an area representative of a SMOS pixel. Microwave radiometer observations, acquired over southwestern France by the CAROLS instrument were analyzed in order to assess their sensitivity to surface soil moisture (w_g). A combination of microwave brightness temperature (T_b) at either two polarizations or two contrasting incidence angles was used to retrieve w_g through regressed empirical logarithmic equations with good results, depending on the chosen configuration. The regressions derived from the CAROLS measurements were applied to the SMOS T_b and their retrieval performance was evaluated. The retrievals of w_g showed significant correlation (p-value < 0.05) with surface measurements for most of the SMOSMANIA stations (8 of 12 stations) and with additional field measurements at two specific sites, also. Root mean square errors varied from 0.03 to 0.09 m³ m^− 3 (0.06 m³ m^− 3 on average).