CO2 hydrogenation over Pd-modified methanol synthesis catalysts

The effect of palladium incorporation on the performance of Cu–ZnO(Al₂O₃) during the hydrogenation of carbon dioxide has been assessed. Temperature-programmed reduction profiles and X-ray photoelectron spectra of copper revealed that Pd enhances copper oxide reduction. Carbon dioxide conversion and methanol yield were found to increase on Pd-loaded catalysts. The importance of the palladium incorporated to the base Cu–ZnO(Al₂O₃) catalyst in determining the catalytic activity is discussed in terms of the relative ease with which hydrogen is dissociated on the Pd particles and then spilt over the Cu–ZnO phase of the base catalyst.     

Tri-reforming of CH4 using CO2 for production of synthesis gas to dimethyl ether

In general, there are three processes for production of synthesis gas; steam reforming, CO₂ reforming and partial oxidation of methane or natural gas. In the present work, we refer to tri-reforming of methane to synthesize syngas with desirable H₂/CO ratios by simultaneous oxy-CO₂-steam reforming of methane. In this study, we report the results obtained on tri-reforming of methane over the Ni/ZrO₂ based catalyst in order to restrain the carbon deposition and to evaluate the catalytic performance. Results of tri-reforming of CH₄ by three catalysts (Ni/Ce–ZrO₂, Ni/ZrO₂ and Haldor Topsoe R67-7H) are showed that the coke on the reactor wall and the surface of catalyst were reduced dramatically. It was found that the weak acidic site, basic site and redox ability of Ce–ZrO₂ play an important role in tri-reforming of methane conversion. Carbon deposition depends not only on the nature of support, but also on the oxidant as like steam or oxygen. Therefore, the process optimization by reactant ratios is important to manufacture the synthesis gas from natural gas and carbon dioxide.     

Catalytic performance for CO2 conversion to methanol of gallium-promoted copper-based catalysts: influence of metallic precursors

This study reports new gallium-promoted copper-based catalysts prepared by co-impregnation of methoxide–acetylacetonate (acac) precursors from methanolic solutions onto silica and zinc oxide supports. Catalyst performance in the CO₂ hydrogenation to methanol was investigated at 2 MPa and temperatures between 523 and 543 K. A high activity and selectivity for ZnO-supported catalysts was found, which also showed a high stability in terms of both activity and selectivity. The maximum value for the activity was 378 g MeOH/kg cat h at 543 K, with a selectivity of 88% towards methanol production. The high performance of these materials in the CO₂ hydrogenation is related to the presence of Ga₂O₃ promoter and highly dispersed Cu⁺ species on the surface, determined by XPS and Auger on used catalysts.     

The efficiency of methanol conversion to CO2 on thin films of Pt and PtRu fuel cell catalysts

Yields were determined for the CO₂ produced upon the electrochemical oxidation of 1.0 M methanol in 0.1 M HClO₄ at the following four fuel cell catalyst systems: Pt black, Pt at 10 wt.% metal loading on Vulcan XC-72R carbon (C/Pt, 10%), PtRu black at 50 at.% Pt, 50 at.% Ru (PtRu (50:50) black), and PtRu at 30 wt.% Pt, 15 wt.% Ru loading on Vulcan XC-72R carbon (C/PtRu, 30 wt.% Pt, 15 wt.% Ru). Samples were electrolyzed in a small volume (50 μl) arrangement for a period of 180 s keeping the reactant depletion in the cell below 1%. The dissolved CO₂ produced was determined ex situ by infrared spectroscopy in a micro-volume transmission flow cell. For the PtRu materials, the efficiencies for CO₂ formation were near 100% at reaction potentials in the range between 0.4 V (versus the reversible hydrogen electrode (RHE), V_RHE ) and 0.9 V_RHE. At the Pt catalysts, the yields of CO₂ approached 80% between 0.8 and 1.1 V_RHE and declined rapidly below 0.8 V_RHE.     

Hydrocarbon synthesis from CO2 over Fe–Cu catalysts

Hydrocarbons and carbon monoxide were produced from carbon dioxide and hydrogen at 400°C over copper-promoted iron catalysts containing sodium. The major surface phases of the catalysts were FeO and/or FeCO₃ although iron carbide is believed as an active phase of the hydrocarbon synthesis from carbon monoxide. Copper was present as metal on the surface and the surface density was considerably high even if the content of copper was less than 1 wt%. The surface density of sodium was not negligible in the catalysts containing sodium less than 0.1 wt% and the sodium ion can affect the surface basicity of the catalysts. The olefin content in the products is believed to relate to the surface basicity.     

Hydrocarbon synthesis through CO2 hydrogenation over CuZnOZrO2/zeolite hybrid catalysts

Direct syntheses of hydrocarbons from CO₂ hydrogenation were investigated over hybrid catalysts consisting of methanol synthesis catalyst (CuZnOZrO₂) and zeolites (MFI and SAPO). The yield of hydrocarbons was strongly depending upon the amount of zeolite's acid sites as measured by NH₃ TPD, while the product distributions were hardly affected by the change of acidity. The main product was ethane in the case of MFI hybrid catalyst and C₃ or C₄ hydrocarbon in the case of SAPO hybrid catalyst. This difference in product distribution was attributed to different mechanism of hydrocarbon formation. Investigation based on the ethene co-reaction suggested that the consecutive mechanism operated for HZSM-5 and the carbon pool mechanism for SAPO.     

Direct synthesis of organic carbonates from the reaction of CO2 with methanol and ethanol over CeO2 catalysts

The catalytic properties of CeO₂ catalysts in direct synthesis of dimethyl carbonate (DMC) from CH₃OH and CO₂ were investigated. The formation rate of DMC over the catalysts calcined at 873 K and above was almost proportional to the surface area of catalysts. However, CeO₂ calcined at 673 K showed lower activity than expected from the surface area. From the results of catalyst characterization, CeO₂ calcined at 673 K contained considerable amount of amorphous phase. In contrast, the ratio of amorphous phase decreased on the catalysts calcined at 873 K and above. This suggests that stable crystallite surface is active for the reaction.

In the CH₃OH + C₂H₅OH + CO₂ reaction at low temperature, ethyl methyl carbonate (EMC) was formed, and selectivity of EMC formation was comparable to that of DMC. The formation route is discussed by the comparison with transesterification reaction.     

CO2 reforming of CH4 over nanocrystalline zirconia-supported nickel catalysts

Mesoporous nanocrystalline zirconia with high-surface area and pure tetragonal crystalline phase has been prepared by the surfactant-assisted route, using Pluronic P123 block copolymer surfactant. The synthesized zirconia showed a surface area of 174 m² g⁻¹ after calcination at 700 °C for 4 h. The prepared zirconia was employed as a support for nickel catalysts in dry reforming reaction. It was found that these catalysts possessed a mesoporous structure and even high-surface area. The activity results indicated that the nickel catalyst showed stable activity for syngas production with a decrease of about 4% in methane conversion after 50 h of reaction. Addition of promoters (CeO₂, La₂O₃ and K₂O) to the catalyst improved both the activity and stability of the nickel catalyst, without any decrease in methane conversion after 50 h of reaction.     

Development of high performance Raney Cu-based catalysts for methanol synthesis from CO2 and H2

Catalytic hydrogenation of CO₂ into methanol has been investigated over Raney Cu-based catalysts. The Raney catalysts leached in NaOH/ZnO solutions showed high activities and selectivities for methanol synthesis. The deposition of Zn on the surface of Cu particles increased the surface area and the specific activity of Raney Cu–M. Raney Cu–Zr developed was significantly more active than a commercial catalyst.     

Active sites in Cu/ZnO/ZrO2 catalysts for methanol synthesis from CO/H2

Among various Cu/ZnO/ZrO₂ catalysts with the Cu/Zn ratio of 3/7, the one with 15 wt.% of ZrO₂ obtains the best activity for methanol synthesis by hydrogenation of CO. The TPR, TPO and XPS analyses reveal that a new copper oxide phase is formed in the calcined Cu/ZnO/ZrO₂ catalysts by the dissolution of zirconium ions in copper oxide. In addition, the Cu/ZnO/ZrO₂ catalyst with 15 wt.% of ZrO₂ turns out to contain the largest amount of the new copper oxide phase. When the Cu/ZnO/ZrO₂ catalysts is reduced, the Cu²⁺ species present in the ZrO₂ lattice is transformed to Cu⁺ species. This leads to the speculation that the addition of ZrO₂ to Cu/ZnO catalysts gives rise to the formation of Cu⁺ species, which is related to the methanol synthesis activity of Cu/ZnO/ZrO₂ catalyst in addition to Cu metal particles. Consequently, the ratio of Cu⁺/Cu⁰ is an important factor for the specific activity of Cu/ZnO/ZrO₂ catalyst for methanol synthesis.     

Effects of modification of silica gel and ADH on enzyme activity for enzymatic conversion of CO2 to methanol

CO₂ can be converted to MeOH through an enzymatic approach in three steps: (1) converting CO₂ to HCOOH by formate dehydrogenase (FateDH), (2) converting HCOOH to HCHO by formaldehyde dehydrogenase (FaldDH) and (3) converting HCHO to MeOH by alcohol dehydrogenase (ADH). Polyethylene glycol (PEG) was used to adjust the pore size of immobilization carrier silica gel and SC-PEG was used to improve the catalytic property of ADH. The catalytic properties of pegylated ADH were investigated using the conversion of HCHO to MeOH as model reaction. The results show that PEG modification of the silica matrix and/or the ADH significantly increases the enzymatic activities.     

Direct synthesis of acetic acid from CH4 and CO2 by a step-wise route over Pd/SiO2 and Rh/SiO2 catalysts

The theoretical and experimental feasibility of direct conversion of CH₄ and CO₂ to acetic acid by an isothermal step-wise route over Pd/SiO₂ and Rh/SiO₂ catalysts was investigated. The methyl radical formation from CH₄ dissociation and CO₂ inserting into the intermediate are regarded as two limiting steps. Preliminary experimental results have shown that the following step-wise route can circumvent the thermodynamic limitation of this direct synthesis at low temperatures. Pd catalysts are more active than Rh catalysts at 170 °C and 200 °C, while formic acid is only produced on Pd catalysts. The optimum contact time of CH₄ and CO₂ with catalysts is 1 min under the experimental conditions. And there is no apparent deactivation resulting from carbon deposition for catalysts during the successive reaction cycles.     

Catalytic decomposition of methane and methane/CO2 mixtures to produce synthesis gas and nanostructured carbonaceous material

Methane and CO₂ are the main components of biogas; therefore its direct conversion into a higher added value gas as syn-gas (mixture of CO and H₂) is a very interesting alternative for the valorisation of such renewable resource. In this work, firstly a thermodynamic analysis of the decomposition of CH₄:CO₂ mixtures at different temperatures and CH₄:CO₂ ratios simulating the biogas composition, has been carried out. Secondly, the decomposition of a mixture with a molar ratio of 1:1 has been studied in a fixed-bed reactor by using a Ni/Al₂O₃ based catalyst, at the temperature range in which according to the thermodynamic study, carbon formation is favoured. Results obtained have been compared to those of methane decomposition carried out under the same experimental conditions. Co-feeding of CO₂ and CH₄ avoids catalyst deactivation substantially, allowing to obtain a syn-gas with H₂:CO ratio close to 1. Moreover, the carbon obtained from mixtures of CH₄ and CO₂ is deposited as fishbone carbon nanofibres at 600 °C and ribbon carbon nanofibers at 700 °C, both being materials with high added value which can be used in multiple applications.     

Potential of zeolite supported rhodium catalysts for the CO2 reforming of CH4

Zeolite Y supported rhodium catalysts were prepared by ion-exchange starting from an aqueous solution of [Rh[(NH₃)₅Cl]Cl₂·6H₂0]. Previous work in this laboratory had shown that this procedure results in a Rh dispersion of near 100%. The catalysts were tested for their activity in the CO₂ reforming of CH₄. They were found to combine extraordinary stability with high activity and selectivity. At 923 K, 90 mol-% of the CH₄ was converted giving a H₂/CO ratio near unity. A weight loading of 0.5 to 0.93% Rh gives the highest turnover frequencies. Thermodynamic equilibrium is reached near 873 K. With a given Rh loading, the zeolite supports are superior to amorphous supports and NaY is superior to the HY. No deactivation was observed in tests of 30 h time on stream at atmospheric pressure or after repeated thermal cycles. No coke deposition was detected by temperature programmed oxidation of used catalysts. Temperature programmed reduction indicates the presence of three discernible Rh species.     

Catalytic conversion of methane and CO2 to synthesis gas over a La2O3-modified SiO2 supported Ni catalyst in fluidized-bed reactor

In this contribution, a commercial spherical SiO₂ was modified with different amounts of La₂O₃, and used as the support of Ni catalysts for autothermal reforming of methane in a fluidized-bed reactor. Nitrogen adsorption, XRD and H₂-TPR analysis indicated that La₂O₃-modified SiO₂ had higher surface area, strengthened interaction between Ni and support, and improved dispersion of Ni. CO₂-TPD found that La₂O₃ increased the alkalescence of SiO₂ and improved the activation of CO₂. Coking reaction (via both temperature-programmed surface reaction of CH₄ (CH₄-TPSR) and pulse decomposition of CH₄) disclosed that La₂O₃ reduced the dehydrogenation ability of Ni. CO₂-TPO, O₂-TPO (followed after CH₄-TPSR) confirmed that only part amount of carbon species derived from methane decomposition could be removed by CO₂, and O₂ in feed played a crucial role for the gasification of the inactive surface carbons. Ni/xLa₂O₃-SiO₂ (x = 10, 15, 30) possessed high activity and excellent stability for autothermal reforming of methane in a fluidized-bed reactor.     

Hydrogenation of carbon dioxide to methanol over palladium-promoted Cu/ZnO/A12O3 catalysts

The effect of Pd on a Cu/ZnO/A1₂O₃ catalyst for methanol synthesis from CO₂/H₂ has been investigated. Activities of impregnated catalysts and physical mixtures were studied in an internal recycle reactor under 5 MPa, 250°C and a range of conversions. In all cases, the promotion of methanol production was greater at higher flow rates (lower conversions). The promotion achieved by use of Pd/A1₂O₃+ Cu/ZnO/Al₂O₃ physical mixtures was found to increase with Pd content. Greater promotion was observed over the Pd impregnated Cu/ZnO/Al₂O₃ catalysts, although this was insensitive to the particular Pd loadings used. The results are consistent with the proposal that hydrogen spillover is responsible for the observed promotion. The effectiveness of Pd as a promoter for the reduction of CuO in the catalysts was studied by TPR and was found to be related to the level of promotion in methanol production.     

Partial oxidation of methane to synthesis gas over Co/Ca/Al2O3 catalysts

A series of calcium-modified alumina-supported cobalt catalysts were prepared with a two-step impregnation method, and the effect of calcium on the catalytic performances of the catalysts for the partial oxidation of methane to syngas (CO and H₂) was investigated at 750 °C. Also, the catalysts were characterized by XRD, TEM, TPR and (in situ) Raman. At 6 wt.% of cobalt loading, the unmodified alumina-supported cobalt catalyst showed a very low activity and a rapid deactivation, while the calcium-modified catalyst presented a good performance for this process with the CH₄ conversion of 88%, CO selectivity of 94% and undetectable carbon deposition during a long-time running. Characterization results showed that the calcium modification can effectively increase the dispersion and reducibility of Co₃O₄, decrease the Co metal particle size, and suppress the reoxidation of cobalt as well as the phase transformation to form CoAl₂O₄ spinel phases under the reaction conditions. These could be related to the excellent catalytic performances of Co/Ca/Al₂O₃ catalysts.     

Partial oxidation of methane to CO and H2 over nickel and/or cobalt containing ZrO2, ThO2, UO2, TiO2 and SiO2 catalysts

The influence of different metal oxide supports (i.e. ZrO₂, ThO₂, UO₂, TiO₂ and SiO₂) on the performance of Ni- and/or Co-containing catalysts [Ni and/or Co/MO₂ mole ratio (where M=Zr, Th, U, Ti or Si)=1.0] in the oxidative methane-to-syngas conversion at very low contact time (GHSV=5.2×10⁵ cm³ g⁻¹ h⁻¹ at STP) was investigated. The nickel-containing ZrO₂, ThO₂ and UO₂ catalysts (with or without pre-reduction by hydrogen at 500°C) showed good performance in the process; the order of their performance is NiO–ThO₂>NiO–UO₂>NiO–ZrO₂. The NiO–TiO₂ showed appreciable catalytic activity only after its reduction at 800°C. However, this catalyst and the NiO–SiO₂ catalyst showed poor performance in the process. These two catalysts are also deactivated very fast, mostly because of sintering of Ni and/or formation of catalytically inactive binary metal oxide phases by solid–solid reaction at the high catalyst calcination and/or catalytic reaction temperature. Although the Ni-containing ThO₂, UO₂ and ZrO₂ catalysts showed good performance, carbon deposition on them during the process is fast. However, because of the addition of cobalt to these catalysts (with Co/Ni=1.0), the rate of carbon deposition on them in the process is drastically reduced. This Co addition however resulted in a significant decrease in both the conversion and selectivity; the decrease in the selectivity was small.     

Effect of methanol addition on water–CO2–diethanolamine system: Influence on CO2 solubility and on liquid phase speciation

The aim of this study is the characterisation of VLE and chemical equilibria for the system CO₂/diethanolamine (DEA)/H₂O/methanol. The effect of MeOH composition has been studied using four compositions (from 0 to 30 wt% of methanol with a fixed composition (30 wt%) of DEA), the measurement being made at T = 298.15 K and at various CO₂ loadings (from 0.2 to 0.8). An original experimental device was used. This device combines a FT-IR spectroscopy analysis of the liquid phase with a VLE measurement cell.The data base obtained, including the new solubility data and the liquid phase composition, allows the modelling of the system CO₂/DEA/H₂O/methanol using an electrolyte equation of state [Fürst, W., Renon, H., 1993, Representation of excess properties of electrolyte solutions using a new equation of state, AIChE J, 39(2): 335–343] representing the equilibrium properties of the system and the liquid phase speciation.     

Separation of CO2 from flue gas using electrochemical cells

Past research with high temperature molten carbonate electrochemical cells has shown that carbon dioxide can be separated from flue gas streams produced by pulverized coal combustion for power generation. However, the presence of trace contaminants, i.e., sulfur dioxide and nitric oxides, will impact the electrolyte within the cell. If a lower temperature cell could be devised that would utilize the benefits of commercially-available, upstream desulfurization and denitrification in the power plant, then this CO₂ separation technique can approach more viability in the carbon sequestration area. Recent work has led to the assembly and successful operation of a low temperature electrochemical cell. In the proof-of-concept testing with this cell, an anion exchange membrane was sandwiched between gas-diffusion electrodes consisting of nickel-based anode electrocatalysts on carbon paper. When a potential was applied across the cell and a mixture of oxygen and carbon dioxide was flowed over the wetted electrolyte on the cathode side, a stream of CO₂ to O₂ was produced on the anode side, suggesting that carbonate/bicarbonate ions are the CO₂ carrier in the membrane. Since a mixture of CO₂ and O₂ is produced, the possibility exists to use this stream in oxy-firing of additional fuel.From this research, a novel concept for efficiently producing a carbon dioxide rich effluent from combustion of a fossil fuel was proposed. Carbon dioxide and oxygen are captured from the flue gas of a fossil-fuel combustor by one or more electrochemical cells or cell stacks. The separated stream is then transferred to an oxy-fired combustor which uses the gas stream for ancillary combustion, ultimately resulting in an effluent rich in carbon dioxide. A portion of the resulting flow produced by the oxy-fired combustor may be continuously recycled back into the oxy-fired combustor for temperature control and an optimal carbon dioxide rich effluent.