The Bi2O3–Nb2O5–NiO Phase Diagram

The Bi₂O₃–Nb₂O₅–NiO phase diagram at 1100°C was determined by means of solid-state synthesis, X-ray diffraction, and scanning electron microscopy. A ternary eutectic with a melting point below 1100°C was found to exist in the field between NiO, Bi₂O₃, and the end-member of the δBi₂O₃–Nb₂O₅ solid solution. The existence of the previously reported Bi₃Ni₂NbO₉ phase was disproved. A pyrochlore homogeneity range around Bi_1.5Ni_0.67Nb_1.33O_6.25 was determined together with all the phase relations in this phase diagram.     

Electrical Properties of Sr0.7Ba0.3TiO3 Ceramics Doped with Nb2O5, 3Li2O · 2SiO2, and Bi2O3

The electrical properties of Sr_0.5Ba_0.3TiO₃ in the presence of Nb₂O₅ as a donor, 3Li₂O · 2SiO₂ as a sintering agent, and Bi₂O₃ as a dopant have been studied. When the compositions of the ceramics were 1 mol Sr_0.7Ba_0.3TiO₃+ 0.5 mol% Nb₂O₅+ 2 mol% 3Li₂O · 2SiO₂+ 0.2 mol% Bi₂O₃, the ceramics were sintered at 1100°C and exhibited the following characteristics: apparent dielectric constant ɛ, 25000; loss factor tan δ, 2%; insulating resistivity ρ_j, 10¹⁰Ω· cm; variation of dielectric constant with temperature Δɛ/ɛ (−25° to +85°C), +10%, −14%. ɛ and tan δ show only small changes with frequency. The study shows this ceramic can be used in multilayer technology.     

Nanopowder Preparation and Dielectric Properties of a Bi2O3–Nb2O5 Binary System Prepared by the High-Energy Ball-Milling Method

The high-energy ball-milling (HEM) method was used to synthesize the compositions of BiNbO₄, Bi₅Nb₃O₁₅, and Bi₃NbO₇ in a Bi₂O₃–Nb₂O₅ binary system. Reagent Bi₂O₃ and Nb₂O₅ were chosen as the starting materials. The X-ray diffraction patterns of the three compositions milled for different times were studied. Only the cubic Bi₃NbO₇ phase, Nb₂O₅, and amorphous matters were observed in powders after being milled for 10 h. After heating at proper temperatures the amorphous matters disappeared and the proleptic phases of BiNbO₄ and Bi₅Nb₃O₁₅ could be obtained. The Scherrer formula was used to calculate the crystal size and the results of nanopowders are between 10 and 20 nm. The scanning electron microscopy photos of Bi₃NbO₇ powders showed drastic aggregation, and the particle size was about 100 nm. The dielectric properties of ceramics sintered from the nanopowders prepared by HEM at 100–1 MHz and the microwave region were measured. Bi₃NbO₇ ceramics showed a good microwave permittivity ɛ_r of about 80 and a Q × f of about 300 at 5 GHz. The triclinic phase of BiNbO₄ ceramics reached its best properties with ɛ_r=24 and Q × f =14 000 GHz at about 8 GHz.     

Effect of Bi2O3 Addition on the Sintering Temperature and Microwave Dielectric Properties of Zn2SiO4 Ceramics

Bi₂O₃ was added to a nominal composition of Zn_1.8SiO_3.8 (ZS) ceramics to decrease their sintering temperature. When the Bi₂O₃ content was <8.0 mol%, a porous microstructure with Bi₄(SiO₄)₃ and SiO₂ second phases was developed in the specimen sintered at 885°C. However, when the Bi₂O₃ content exceeded 8.0 mol%, a liquid phase, which formed during sintering at temperatures below 900°C, assisted the densification of the ZS ceramics. Good microwave dielectric properties of Q × f =12,600 GHz, ɛ_r=7.6, and τ_f=−22 ppm/°C were obtained from the specimen with 8.0 mol% Bi₂O₃ sintered at 885°C for 2 h.     

Subsolidus Phase Equilibria in the System Bi2O3-TiO2-Nb2O5

The subsolidus phase equilibria in the system Bi₂O₃-TiO₂-Nb₂O₅ at 1100°C were determined by solid-state reaction techniques and X-ray powder diffraction methods. The system was found to contain 4 ternary compounds, i.e. Bi₃TiNbO₉, Bi₇Ti₄NbO₂₁, a cubic pyrochlore solid solution having a compositional range of 3Bi₂O₃· x TiO₂ (7– x )Nb₂O₅ where x ranges from 2.3 to 6.75, and an unidentified phase, 4Bi₂O₃·11TiO₂·5Nb₂O₅.     

Effect of Nb2O5/ZnO Addition on Microwave Properties of (Zr0.8Sn0.2)TiO4 Ceramics

The effects of Nb₂O₅ and ZnO addition on the dielectric properties, especially the quality factor, of (Zr_0.8Sn_0.2)TiO₄ (ZST) ceramics were investigated in terms of the sintered density acquired by the zinc. For ZST ceramics with 2 mol% added ZnO, the relative density of the samples decreased with >0.5 mol% addition of Nb₂O₅. On the other hand, for samples with 6 mol% added ZnO, the relative density remained >97%, even when the amount of Nb₂O₅ was increased to 2.0 mol%. When >0.5 mol% Nb₂O₅ was added, both the quality factor and the dielectric constant exhibited similar trends with sintered density. The ZST ceramics with 6 mol% added ZnO, especially, still manifested a quality factor >40 000 and a dielectric constant of 37, even when the amount of Nb₂O₅ was increased, values that are not explainable by the previously suggested electronic defect model.     

Sintering Behavior and Dielectric Properties of Bi3NbO7 Ceramics Prepared by Mixed Oxides and High-Energy Ball-Milling Methods

The sintering behavior and dielectric properties of Bi₃NbO₇ ceramics prepared by the high-energy ball milling (HEM) method and conventional mixed oxides method with V₂O₅ addition were investigated. All the samples were sintered between 840° and 960°C. For the ceramics prepared by the mixed oxides method, the pure tetragonal Bi₃NbO₇ phase formed without any cubic phase. With changing sintering temperature, the dielectric constant ɛ_r lies between 79 and 92, while the Q × f values are between 300 and 640 GHz. The samples sintered at 870°C have the best microwave dielectric properties with ɛ_r=79, Q × f =640 GHz, and the temperature coefficients of resonant frequency τ_f between 0 and −20 ppm/°C. For the ceramics prepared by the HEM, a pure cubic phase was obtained. The ɛ_r changes between 78 and 80 and Q × f were between 200 and 290 GHz.     

Microwave Dielectric Properties of Low Firing Temperature Bi2W2O9 Ceramics

Phase stability, sinterability, and microwave dielectric properties of Bi₂W₂O₉ ceramics and their cofireability with Ag, Cu, and Au electrodes have been investigated. Single-phase Bi₂W₂O₉ powder was synthesized by solid-state reaction in air at 800°C for 3 days. X-ray powder diffraction data show Bi₂W₂O₉ to have an orthorhombic crystal structure described by the noncentrosymmetric space group Pna 2₁, with lattice parameters a =5.4401(8), b =5.4191(8), c =23.713(4) Å. Ceramics fired at temperatures up to 865°C remain single-phase but above this temperature ferroelectric Bi₂WO₆ appears as a secondary phase. The measured relative permittivity of Bi₂W₂O₉ ceramics increases continuously from 28.6 to 40.7 for compacts fired between 860° and 885°C. The bulk relative permittivity of Bi₂W₂O₉ corrected for porosity was calculated as 41.3. Bi₂W₂O₉ ceramics fired up to 875°C exhibit moderate quality factors, Q × f _r, ∼7500–7700 GHz and negative temperature coefficient of resonant frequency, ∼−54 to −63 ppm/°C. Chemical compatibility experiments show Bi₂W₂O₉ ceramics to react with both Ag and Cu electrodes, but to form good contacts with Au electrodes.     

Phase Relations and Dielectric Properties in the Bi2O3–ZnO–Ta2O5 System

Dielectric properties and phase formation of Bi-based pyrochlore ceramics were evaluated for the Bi₂O₃–ZnO–Ta₂O₅ system. The compositional range r Bi₂(Zn_1/3Ta_2/3)₂O₇· (1− r )(Bi_3/2Zn_1/2)(Zn_1/2Ta_3/2)O₇ (0 ≤ r ≤ 1) in Bi₂O₃–ZnO–Ta₂O₅ was investigated to determine the relative solubility of BZT cubic (α-BZT, r = 0) and the pseudo-orthorhombic (β-BZT, r = 1) end members. It was found that extrinsic factors, such as kinetically limited phase formation and bismuth loss, contribute to apparent phase boundaries in addition to thermodynamic stability of each phase. Considering this, the locations of true phase boundaries were r < 0.30 and r ≥ 0.74 for α and β phases, respectively. Dielectric constants between 58 and 80 and low dielectric loss (tan δ < 0.003) were measured for the complete compositional range. The temperature coefficient of capacitance was controlled by composition, which was found to be <30 ppm/°C at the edge of β-phase solid solution. In addition to the excellent dielectric properties these materials can be sintered at low temperatures, which make Bi-based pyrochlores promising candidates for high-frequency electronic applications.     

Phase Relations in the System Bi2O3-WO3

Phase relations in the system Bi₂O₃-WO₃ were studied from 500° to 1100°C. Four intermediate phases, 7Bi₂O₃· WO₃, 7Bi₂O₃· 2WO₃, Bi₂O₃· WO₃, and Bi₂O₃· 2WO₃, were found. The 7B₂O · WO₃ phase is tetragonal with a ₀= 5.52 Å and c ₀= 17.39 Å and transforms to the fcc structure at 784°C; 7Bi₂O₃· 2WO₃ has the fcc structure and forms an extensive range of solid solutions in the system. Both Bi₂O₃· WO₃ and Bi₂O₃· 2WO₃ are orthorhombic with (in Å) a ₀= 5.45, b ₀=5.46, c ₀= 16.42 and a ₀= 5.42, b ₀= 5.41, c ₀= 23.7, respectively. Two eutectic points and one peritectic exist in the system at, respectively, 905°± 3°C and 64 mol% WO₃, 907°± 3°C and 70 mol% WO₃, and 965°± 5°C and 10 mol% WO₃.     

Microwave Dielectric Properties of 5Li2O–0.583Nb2O5–3.248TiO2 Ceramics with V2O5

The effects of V₂O₅ addition on the sintering behavior, microstructure, and the microwave dielectric properties of 5Li₂O–0.583Nb₂O₅–3.248TiO₂ (LNT) ceramics have been investigated. With addition of low-level doping of V₂O₅ (≤2 wt%), the sintering temperature of the LNT ceramics could be lowered down to around 920°C due to the liquid phase effect. A secondary phase was observed at the level of 2 wt% V₂O₅ addition. The addition of V₂O₅ does not induce much degradation in the microwave dielectric properties but lowers the τ_f value to near zero. Typically, the excellent microwave dielectric properties of ɛ_r=21.5, Q × f =32 938 GHz, and τ_f=6.1 ppm/°C could be obtained for the 1 wt% V₂O₅-doped sample sintered at 920°C, which is promising for application of the multilayer microwave devices using Ag as an internal electrode.     

Effects of Excess Bi2O3 on the Ferroelectric Behavior of Nd-Doped Bi4Ti3O12 Thin Films

Effects of excess Bi₂O₃ content on formation of (Bi_3.15Nd_0.85)Ti₃O₁₂ (BNT) films deposited by RF sputtering were investigated. The microstructures and electrical properties of BNT thin films are strongly dependent on the excess Bi₂O₃ content and post-sputtering annealing temperature, as examined by XRD, SEM, and P – E hysteresis loops. A small amount of excess bismuth improves the crystallinity and therefore polarization of BNT films, while too much excess bismuth leads to a reduction in polarization and an increase in coercive field. P – E loops of well-established squareness were observed for the BNT films derived from a moderate amount of Bi₂O₃ excess (5 mol%), where a remanent polarization 2P _r of 25.2 μC/cm² and 2E _c of 161.5 kV/cm were shown. A similar change in dielectric constant with increasing excess Bi₂O₃ content was also observed, with the highest dielectric constant of 304.1 being measured for the BNT film derived from 5 mol% excess Bi₂O₃.     

Dielectric Relaxations in Bi2O3–Nb2O5–NiO Cubic Pyrochlores

Dielectric properties of pyrochlores compositions from Bi₂O₃–Nb₂O₅–NiO system were analyzed. The dielectric properties are dominated with a low-temperature relaxation that is typical for Bi-pyrochlores. A vast pyrochlore homogeneity range that exists in this system allowed to correlate characteristics of the observed relaxations with a compositional variations within the A₂O'- and B₂O₆ pyrochlore sublattice. It was possible to make a distinction between different influences of the two sublattices, which can be satisfactorily described by the existing relaxation model for Bi_3/2ZnNb_3/2O₇. A new relaxor-like room temperature relaxation was found for Bi_1.6Ni_0.57Nb_1.43O_6.55.     

Microwave Dielectric Properties of CaTiO3-CaAl1/2Nb1/2O3 Ceramics Doped with Li3NbO4

The microwave dielectric properties of CaTi_{1− x} (Al_1/2Nb_1/2) _x O₃ solid solutions (0.3 ≤ x ≤ 0.7) have been investigated. The sintered samples had perovskite structures similar to CaTiO₃. The substitution of Ti⁴⁺ by Al³⁺/Nb⁵⁺ improved the quality factor Q of the sintered specimens. A small addition of Li₃NbO₄ (about 1 wt%) was found to be very effective for lowering sintering temperature of ceramics from 1450–1500° to 1300°C. The composition with x = 0.5 sintered at 1300°C for 5 h revealed excellent dielectric properties, namely, a dielectric constant (ɛ_r) of 48, a Q × f value of 32 100 GHz, and a temperature coefficient of the resonant frequency (τ_f) of −2 ppm/K. Li₃NbO₄ as a sintering additive had no harmful influence on τ_f of ceramics.     

Tailoring the Microwave Dielectric Properties of MgNb2O6 and Mg4Nb2O9 Ceramics

The columbites MgNb₂O₆, MgTa₂O₆, and corundum-type Mg₄Nb₂O₉ ceramics were prepared by the conventional solid-state ceramic route. The structure and microstructure of the sintered samples were investigated by X-ray diffraction and scanning electron microscopic techniques. The microwave dielectric properties of the samples were measured by the resonance method in the frequency range 4–6 GHz. The dielectric properties have been tailored by forming a solid solution between MgNb₂O₆ and MgTa₂O₆ and by the substitution of TiO₂ for Nb₂O₅ in both MgNb₂O₆ and Mg₄Nb₂O₉ ceramics. The Mg(Nb_0.7Ta_1.3)O₆ has ɛ_r=29, Q _u× f =67 800 GHz, and τ_f=0.8 ppm/°C and the MgO–(0.4)Nb₂O₅–(1.5)TiO₂ composition has ɛ_r=34.5, Q _u× f =81 300 GHz, and τ_f=−2 ppm/°C.     

Phase Formation and Dielectric Characterization of the Bi2O3–TeO2 System Prepared in an Oxygen Atmosphere

Solid-state synthesis of compositions from the Bi₂O₃–TeO₂ system show that, under an oxygen atmosphere, Te⁴⁺ oxidizes to Te⁶⁺ and yields four room-temperature stable compounds: Bi₂Te₂O₈, Bi₂TeO₆, Bi₆Te₂O₁₅, and new a compound with the nominal composition 7Bi₂O₃·2TeO₂. Dense ceramics can be prepared from all these compounds by sintering between 650° and 800°C under an oxygen atmosphere. The permittivity of these compounds varies from ∼30 to ∼54, the Q × f value from 1.100 to 41.000 GHz (∼5 GHz), and the temperature coefficient of resonant frequency from −43 to −144 ppm/K. Bi₆Te₂O₁₅ and 7Bi₂O₃·2TeO₂ do not react with silver, and, therefore, they have the potential to be used for applications in low-temperature cofired ceramic (LTCC) technology.     

Temperature/Composition Phase Diagram of the System Bi2O3-PbO

The Bi₂O₃-PbO phase diagram was determined using differential thermal analysis and both room- and high-temperature X-ray powder diffraction. The phase diagram contains a single eutectic at 73 mol% PbO and 635°C. A body-centered cubic solid solution exists above ∼600°C within a composition range of 30 to 65 mol% PbO. The compounds α-Bi₂O₃, σ5-Bi₂O₃, and γ-PbO (litharge) have wide solubility ranges. Four compounds, 6Bi₂O₃·PbO, 3Bi₂O₃·2PbO, 4Bi₂O₃,5PbO, and Bi₂O₃·3PbO, are formed in this system and the previously unreported X-ray diffraction patterns of the latter three compounds are reported. Diffraction patterns for some of these mixed oxides have been observed in ZnO-based varistors grown using Bi₂O₃ and PbO as sintering aids.     

Synthesis of BaCu(B2O5) Ceramics and their Effect on the Sintering Temperature and Microwave Dielectric Properties of Ba(Zn1/3Nb2/3)O3 Ceramics

BaCu(B₂O₅) ceramics were synthesized and their microwave dielectric properties were investigated. BaCu(B₂O₅) phase was formed at 700°C and melted above 850°C. The BaCu(B₂O₅) ceramic sintered at 810°C had a dielectric constant (ɛ_r) of 7.4, a quality factor ( Q × f ) of 50 000 GHz and a temperature coefficient of resonance frequency (τ_f) of −32 ppm/°C. As the BaCu(B₂O₅) ceramic had a low melting temperature and good microwave dielectric properties, it can be used as a low-temperature sintering aid for microwave dielectric materials for low temperature co-fired ceramic application. When BaCu(B₂O₅) was added to the Ba(Zn_1/3Nb_2/3)O₃ (BZN) ceramic, BZN ceramics were well sintered even at 850°C. BaCu(B₂O₅) existed as a liquid phase during the sintering and assisted the densification of the BZN ceramic. Good microwave dielectric properties of Q × f =16 000 GHz, ɛ_r=35, and τ_f=22.1 ppm/°C were obtained for the BZN+6.0 mol% BaCu(B₂O₅) ceramic sintered at 875°C for 2 h.     

Structural and Dielectric Properties of Ag(Nb0.8Ta0.2)1−xSbxO3 (x≤0.08) Ceramics

Sb₂O₅ were selected to substitute (Nb_0.8Ta_0.2)₂O₅ and the effects of Sb substitution on the dielectric properties of Ag(Nb_0.8Ta_0.2)O₃ ceramics were studied. The perovskite Ag(Nb_0.8Ta_0.2)_{1− x} Sb _x O₃ ceramics showed no obvious change with x value being no more than 0.08, and the pseudoperovskite unit cell parameters a = c , b and monoclinic angle β decrease with Sb concentration increasing. The dielectric properties of Ag(Nb_0.8Ta_0.2)_{1− x} Sb _x O₃ ceramics were found to be affected greatly by the substitution of Sb for Nb/Ta. The ɛ value of Ag(Nb_0.8Ta_0.2)_{1− x} Sb _x O₃ ceramics sintered at their densified temperature increased from 480 to 825 with x from 0 to 0.08, the tan δ value decreased sharply from 0.0065 to 0.0023 (at 1 MHz) with x increasing from 0 to 0.04, and then kept a stable lower tan δ value ∼0.0024 with x to 0.08. The temperature coefficient of capacitance values continuously decreased from a positive value of 1450 ppm/°C for x =0 to a negative value of −38.52 ppm/°C for x =0.08.     

Microwave Dielectric Properties and Chemical Resistance of Low-Temperature-Sintered CaZrB2O6 Ceramics

Dolomite-type borate ceramics consisting of CaZrB₂O₆ were synthesized via a conventional solid-state reaction route; low-temperature sintering was explored using Bi₂O₃–CuO additives of 1–7 wt% for low-temperature co-fired ceramics applications. For several sintering temperatures, the microwave dielectric properties and chemical resistance of the ceramics were investigated. The CaZrB₂O₆ ceramics with 3 wt% Bi₂O₃–CuO addition could be sintered below 925°C, and the microwave dielectric properties of the low-temperature samples were ɛ_r=10.55, Q × f =87,350 GHz, and τ_f=+2 ppm/°C. The chemical resistance test result showed that both CaZrB₂O₆- and Bi₂O₃–CuO-added CaZrB₂O₆ ceramics were durable in basic solution but were degraded in acid solution.