Synthesis and characterization of polysulfone–poly(alkylene oxide) block copolymers containing poly(dimethylsiloxane)

Block copolymers of polysulfone–poly(alkylene oxide)–poly(dimethylsiloxane) have been prepared by the addition of preformed α,ω-bis(hydrogensilyl)poly(dimethylsiloxane) oligomers to allyl end-capped poly(alkylene oxide)–polysulfone. The hydrosilylation reaction, catalyzed by platinum, was employed for incorporation of the siloxane chain into the copolymers in a 1 : 1 or 1 : 2 molar ratio of Si–H-terminated polydimethylsiloxane to allyl end-capped polysulfone. The products were characterized by IR, ¹H-NMR, and gel permeation chromatography. The thermal stability was determined by thermogravimetric analysis. Differential scanning calorimetry was used to investigate microphase separation in the block copolymers. © 1996 John Wiley & Sons, Inc.     

Conformations of polysulfone‐block‐polydimethylsiloxane chains in solution and in the solid state

Polysulfone block copolymers containing polydimethylsiloxane segments were obtained in solution by the condensation reaction of chloro‐terminated polysulfone oligomers and α,ω‐dihydrogensilyl‐polydimethylsiloxane. The conformations of the copolymer chains were investigated both in solution and in the solid state. Viscometric and UV absorption measurements were carried out in dilute dichloroethane solutions over a wide region of concentrations, in the temperature range 20–75 °C. The results point to a conformational transition phenomenon, located at around 55 °C, which is attributed to the transition from a segregated to a pseudo‐Gaussian conformation through a compressed‐segregated conformation. Copyright © 2004 Society of Chemical Industry     

Synthesis and properties of polystyrene‐b‐poly(ethylene oxide)‐b‐polystyrene triblock copolymers

A series of well‐defined and property‐controlled polystyrene (PS)‐b‐poly(ethylene oxide) (PEO)‐b‐polystyrene (PS) triblock copolymers were synthesized by atom‐transfer radical polymerization, using 2‐bromo‐propionate‐end‐group PEO 2000 as macroinitiatators. The structure of triblock copolymers was confirmed by ¹H‐NMR and GPC. The relationship between some properties and molecular weight of copolymers was studied. It was found that glass‐transition temperature (T_g) of copolymers gradually rose and crystallinity of copolymers regularly dropped when molecular weight of copolymers increased. The copolymers showed to be amphiphilic. Stable emulsions could form in water layer of copolymer–toluene–water system and the emulsifying abilities of copolymers slightly decreased when molecular weight of copolymers increased. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 727–730, 2006     

Phase behavior of temperature‐ and pH‐sensitive poly(acrylic acid‐g‐N‐isopropylacrylamide) in dilute aqueous solution

Several different composition temperature‐ and pH‐sensitive poly(acrylic acid‐g‐N‐isopropylacrylamide) (P(AA‐g‐NIPAM)) graft copolymers were synthesized by free‐radical copolymerization utilizing macromonomer technique. The phase behavior and conformation change of P(AA‐g‐NIPAM) in aqueous solutions were investigated by UV–vis transmittance measurements, fluorescence probe, and fluorescence quenching techniques. The results demonstrate that the P(AA‐g‐NIPAM) copolymers have temperature‐ and pH‐sensitivities, and these different composition graft copolymers have different lower critical solution temperature (LCST) and critical phase transition pH values. The LCST of graft copolymer decreases with increasing PNIPAM content, and the critical phase transition pH value increases with increasing Poly(N‐isopropylacrylamide) (PNIPAM) content. At room temperature (20°C), different composition of P(AA‐g‐NIPAM) graft copolymers in dilute aqueous solutions (0.001 wt %) have a loose conformation, and there is no hydrophobic microdomain formation within researching pH range (pH 3 ～ 10). In addition, for the P(AA‐g‐NIPAM) aqueous solutions, transition from coil to globular is an incomplete reversible process in heating and cooling cycles. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis and characterization of PBMA‐b‐PDMS‐b‐PBMA copolymers by atom transfer radical polymerization

Poly(butyl methylacrylate)–b–poly(dimethylsiloxane)–b–poly(butyl methylacrylate) (PBMA–b–PDMS–b–PBMA) triblock copolymers were synthesized by atom transfer radical polymerization (ATRP). The reaction of α,ω‐dichloride PDMS with 2′‐hydroxyethyl‐2‐bromo‐2‐methylpropanoate gave suitable macroinitiators for the ATRP of BMA. The latter procedure was carried out at 110°C in a phenyl ether solution with CuCl and 4,4′‐di (5‐nonyl)‐2,2′‐bipyridine (dNbpy) as the catalyzing system. The polymerization was controllable, with the increase of the monomer conversion, there was a nearly linear increase of molecular weight and a decrease of polydispersity in the process of the polymerization, and the rate of the polymerization was first‐order with respect to monomer conversion. The block copolymers were characterized with IR and ¹H‐NMR and differential scanning calorimetry. The effects of macroinitiator concentration, catalyst concentration, and temperature on the polymerization were also investigated. Thermodynamic data and activation parameters for the ATRP were reported. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 532–538, 2004     

Redox initiation system of ceric salt and α,ω‐dihydroxy poly(dimethylsiloxane)s for vinyl polymerization

The redox system of ceric salt and α,ω‐dihydroxy poly(dimethylsiloxane) is used to polymerize vinyl monomers such as acrylonitrile and styrene to produce block copolymers. The concentration and type of α,ω‐dihydroxy poly(dimethylsiloxane) affects the yield and the molecular weight of the copolymers. The copolymers have about 20°C lower glass‐transition temperatures and much higher contact angle values than of the corresponding homopolymer of vinyl monomers, although the weight percent of α,ω‐dihydroxy poly(dimethylsiloxane) of the copolymers is in the range of 1–2%. © 2006 Wiley Periodicals Inc. J Appl Polym Sci 102: 2112–2116, 2006     

Synthesis and thermotropic liquid‐crystalline behaviour of novel main‐chain poly(ether ether ketone ketone)s containing a lateral tert‐butyl group

The synthesis of novel poly(ether ether ketone ketone)s containing a lateral group via the random copolymerization of 4,4′‐biphenol, tert‐butylhydroquinone and 1,4‐bis(p‐fluorobenzoyl)benzene is described. The copolymers were characterized by differential scanning calorimetry (DSC), wide‐angle X‐ray diffraction (WAXD) and polarized optical microscopy (POM) observation. The results showed that the thermotropic liquid‐crystalline properties were achieved in the copolymers containing 30 mol% and 50 mol% tert‐butylhydroquinone, which have relatively lower melting temperatures due to the copolymerization effect. Both the crystalline–liquid‐crystalline transition (T_m) and the liquid‐crystalline–isotropic phase transition (T_i) were observable in the DSC thermograms, while the biphenol‐based poly(aryl ether ketone) has only one melting transition. The hydroquinone‐based polymer was shown to be amorphous. Thermogravimetric analysis (TGA) results showed that these copolymers are all high‐temperature resistant with higher glass transition temperature between 147 and 149 °C, and higher decomposition temperature T_d in the range 480–520 °C. © 2000 Society of Chemical Industry     

Synthesis and properties of hydrophilic segmented block copolymers based on poly(ethylene oxide)‐ran‐poly(propylene oxide)

The present article discusses the synthesis and various properties of segmented block copolymers with random copolymer segments of poly(ethylene oxide) and poly(propylene oxide) (PEO‐r‐PPO) together with monodisperse amide segments. The PEO‐r‐PPO contained 25 wt % PPO units and the segment presented a molecular weight of 2500 g/mol. The synthesized copolymers were analyzed by differential scanning calorimetry, Fourier transform infra‐red spectroscopy, atomic force microscopy and dynamic mechanical thermal analysis. In addition, the hydrophilicity and the contact angles (CAs) were studied. The PEO‐r‐PPO segments displayed a single low glass transition temperature, as well as a low PEO crystallinity and melting temperature, which gave enhanced low‐temperature properties of the copolymer. The water absorption values remained high. In comparison to mixtures of PEO/PPO segments, the random dispersion of PPO units in the PEO segments was more effective in reducing the PEO crystallinity and melting temperature, without affecting the hydrophilicity. Increasing the polyether segment length with terephthalic groups from 2500 to 10,000 g/mol increased the hydrophilicity and the room temperature elasticity. Furthermore, the CAs were found to be low 22–39° and changed with the crosslink density. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci 117:1394–1404, 2010     

Synthesis and characterization of a poly(ether–ester) copolymer from poly(2,6 dimethyl‐1,4‐phenylene oxide) and poly(ethylene terephthalate)

A series of poly(ether–ester) copolymers were synthesized from poly(2,6 dimethyl‐1,4‐phenylene oxide) (PPO) and poly(ethylene terephthalate) (PET). The synthesis was carried out by two‐step solution polymerization process. PET oligomers were synthesized via glycolysis and subsequently used in the copolymerization reaction. FTIR spectroscopy analysis shows the coexistence of spectral contributions of PPO and PET on the spectra of their ether–ester copolymers. The composition of the poly(ether–ester)s was calculated via ¹H NMR spectroscopy. A single glass transition temperature was detected for all synthesized poly(ether–ester)s. T_g behavior as a function of poly(ether–ester) composition is well represented by the Gordon‐Taylor equation. The molar masses of the copolymers synthesized were calculated by viscosimetry. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Confined crystallization morphology of poly(ϵ‐caprolactone) block within poly(ϵ‐caprolactone)–poly(l‐lactide) copolymers

The confined crystallization of poly(?‐caprolactone) (PCL) block in poly(?‐caprolactone)–poly(l ‐lactide) (PCL‐PLLA) copolymers was investigated using differential scanning calorimetry, polarized optical microscopy, scanning electronic microscopy and atomic force microscopy. To study the effect of crystallization and molecular chain motion state of PLLA blocks in PCL‐PLLA copolymers on PCL crystallization morphology, high‐temperature annealing (180 °C) and low‐temperature annealing (80 °C) were applied to treat the samples. It was found that the crystallization morphology of PCL block in PCL‐PLLA copolymers is not only related to the ratio of block components, but also related to the thermal history. After annealing PCL‐PLLA copolymers at 180 °C, the molten PCL blocks are rejected from the front of PLLA crystal growth into the amorphous regions, which will lead to PCL and PLLA blocks exhibiting obvious fractionated crystallization and forming various morphologies depending on the length of PLLA segment. On the contrary, PCL blocks more easily form banded spherulites after PCL‐PLLA copolymers are annealed at 80 °C because the preexisting PLLA crystal template and the dangling amorphous PLLA chains on PCL segments more easily cause unequal stresses at opposite fold surfaces of PCL lamellae during the growth process. Also, it was found that the growth rate of banded spherulites is less than that of classical spherulites and the growth rate of banded spherulites decreases with decreasing band spacing. © 2019 Society of Chemical Industry     

Synthesis and thermotropic liquid‐crystalline behavior of novel main‐chain poly(aryl ether ketones)

Novel aromatic poly(ether ketones) containing bulky lateral groups were synthesized via nucleophilic substitution reactions of 4,4′‐biphenol and (4‐chloro‐3‐trifluoromethyl)phenylhydroquinone (CF‐PH) with 1,4‐bis(p‐fluorobenzoyl)benzene. The copolymers were characterized by differential scanning calorimetry (DSC), wide‐angle X‐ray diffraction, and polarized light microscopy observation. Thermotropic liquid‐crystalline behavior was observed in the copolymers containing 40, 50, 60, and 70 mol % CF‐PH. The crystalline–liquid‐crystalline transition [melting temperature (T_m)] and the liquid‐crystalline–isotropic phase transition appeared in the DSC thermograms, whereas the biphenol‐based homopolymer had only a melting transition. The novel poly(aryl ether ketones) had glass‐transition temperatures that ranged from 143 to 151°C and lower T_m's that ranged from 279 to 291°C, due to the copolymerization. The polymers showed high thermal stability, and some exhibited a large range in mesophase stability. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1347–1350, 2003     

Synthesis of block copolymers with thermodynamically compatible chain segments: di‐ and triblock copolymers of polystyrene and poly(2,6‐dimethyl‐1,4‐phenylene oxide)

Mono‐ and bifunctional poly(phenylene oxide) (PPO) macroinitiators for atom transfer radical polymerization (ATRP) were prepared by esterification of mono‐ and bishydroxy telechelic PPO with 2‐bromoisobutyryl bromide. The macroinitiators were used for ATRP of styrene to give block copolymers with PPO and polystyrene (PS) segments, namely PPO‐block‐PS and PS‐block‐PPO‐block‐PS. Various ligands were studied in combination with CuBr as ATRP catalysts. Kinetic investigations revealed controlled polymerization processes for certain ligands and temperature ranges. Thermal analysis of the block copolymers by means of DSC revealed only one glass transition temperature as a result of the compatibility of the PS and PPO chain segments and the formation of a single phase; this glass transition temperature can be adjusted over a wide temperature range (ca 100–199 °C), depending on the composition of the block copolymer. Copyright © 2005 Society of Chemical Industry     

Compatibility of ABA poly(styrene–b–isoprene)/poly(2,6-dimethylphenylene oxide) blends

A variety of blends of ABA poly(styrene–b–isoprene) copolymers with poly(2,6-dimethylphenylene oxide) were prepared. Their compatibility was examined by measuring both the apparent modulus of rigidity and the loss tangent. Several blends showed a unique glass transition temperature between those of the individual components, which indicated compatibility. It was found that only those copolymers which phase separate are compatible with poly(2,6-dimethylphenylene oxide).     

Synthesis and characterization of Pst‐b‐PDMS‐b‐PSt copolymers by atom transfer radical polymerization

Polystyrene‐b‐poly(dimethylsiloxane)‐b‐polystyrene (Pst‐b‐PDMS‐b‐PSt) triblock copolymers were synthesized by atom transfer radical polymerization (ATRP). Commercially available difunctional PDMS containing vinylsilyl terminal species was reacted with hydrogen bromide, resulting in the PDMS macroinitiators for the ATRP of styrene (St). The latter procedure was carried out at 130°C in a phenyl ether solution with CuCl and 4, 4′‐di (5‐nonyl)‐2,2′‐bipyridine (dNbpy) as the catalyzing system. By using this technique, triblock copolymers consisting of a PDMS center block and polystyrene terminal blocks were synthesized. The polymerization was controllable; ATRP of St from those macroinitiators showed linear increases in M_n with conversion. The block copolymers were characterized with IR and ¹H‐NMR. The effects of molecular weight of macroinitiators, macroinitiator concentration, catalyst concentration, and temperature on the polymerization were also investigated. Thermodynamic data and activation parameters for the ATRP are reported. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3764–3770, 2004     

Poly(α-methylstyrene)–poly(dimethylsiloxane) block copolymers

Block copolymers were synthesized by the condensation of dihydroxyl-terminated poly-(α-methylstyrene) oligomers and bisdimethylamino-terminated poly(dimethylsiloxane) oligomers. Manipulation of block molecular weight produced copolymers ranging in composition from 21% to 73% poly(dimethylsiloxane). Compression moldablity was found to be good. Physical properties were dependent upon siloxane content, varying from high modulus, low elongation to low modulus, high elongation materials. High siloxane-content compositions exhibited elastomeric properties due to the two-phase morphology of these systems. Glass transition temperatures were observed as low as ?120°C for the poly(dimethylsiloxane) block and as high as + 140°C for the poly(α-methylstyrene) block. Even higher poly(α-methylstyrene) transition temperatures may be possible by using higher molecular weight oligomers.     

Synthesis and characterization of poly(ε‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(ε‐caprolactone) triblock copolymers with dibutylmagnesium as catalyst

Two series of poly(ε‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(ε‐caprolactone) triblock copolymers were prepared by the ring opening polymerization of ε‐caprolactone in the presence of poly(ethylene glycol) and dibutylmagnesium in 1,4‐dioxane solution at 70°C. The triblock structure and molecular weight of the copolymers were analyzed and confirmed by ¹H NMR, ¹³C NMR, FTIR, and gel permeation chromatography. The crystallization and thermal properties of the copolymers were investigated by wide‐angle X‐ray diffraction (WAXD) and differential scanning calorimetry (DSC). The results illustrated that the crystallization and melting behaviors of the copolymers were depended on the copolymer composition and the relative length of each block in copolymers. Crystallization exothermal peaks (T_c) and melting endothermic peaks (T_m) of PEG block were significantly influenced by the relative length of PCL blocks, due to the hindrance of the lateral PCL blocks. With increasing of the length of PCL blocks, the diffraction and the melting peak of PEG block disappeared gradually in the WAXD patterns and DSC curves, respectively. In contrast, the crystallization of PCL blocks was not suppressed by the middle PEG block. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Thermooxidative degradation behavior of poly(silphenylene–siloxane)s

Copolymers of poly(silphenylene–siloxane) with dimethylsiloxane and diphenylsiloxane with various end groups were synthesized through an Si? H/Si? OR polycondensation process. The thermooxidative degradation behaviors of the copolymers were investigated by thermogravimetric analysis and IR spectrometry techniques. All of the polymers were characterized by a two‐step mass loss. The first one, which peaked at 510–545°C in differential thermogravimetric curves, was mostly caused by the main‐chain depolymerization, whereas the second one, which reached its maximum around 650°C, was caused by side‐group oxidation and Si? C bond scission. The main‐chain depolymerization occurred over a temperature range of some 470–580°C, whereas Si? C bond scission and side‐group oxidation occurred over a temperature range of about 585°C to above 720°C. The incorporation of phenyl groups in the end groups greatly retarded the temperature for the degradation onset of the main chain to 120°C higher. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Reduction and cyclization to form poly(benzimidazole amide imide) copolymers

Poly(amide imide) copolymers were synthesized with different molar ratios of 4,4‐diphenylmethane diisocyanate, two types of aromatic dianhydrides (pyromellitic dianhydride (PMDA) and 3,3′,4,4′‐sulfonyl diphthalic anhydride (DSDA)), and a diacid, which was derived from 3,3′‐dinitrobenzidine and isophthaloyl chloride in a previous work. In this study, the copolymers were further reacted with a reducing agent, and the nitro groups in the copolymers were hydrogenated into amine groups. Then, the amine‐group‐containing poly(amide imide) copolymers were cyclized at 180°C to form the poly(benzimidazole imide amide) copolymers in poly(phosphoric acid), which acted as a cyclizing agent. The resultant copolymers were soluble in sulfuric acid and poly(phosphoric acid) at room temperature and in sulfolane or N‐methyl‐2‐pyrrolidone under heating to 100°C with 5% lithium chloride. According to wide‐angle X‐ray diffraction, all the copolymers were amorphous. According to thermal analysis, the glass‐transition temperature ranged from 270 to 322°C, and the 10% weight‐loss temperature ranged from 460 to 541°C in nitrogen and from 441 to 529°C in air. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 378–386, 2004     

Synthesis and characterization of poly[(butylene succinate)‐co‐(butylene terephthalate)]‐b‐poly(tetramethylene glycol) segmented block copolymer

Polyester‐polyether segmented block copolymers of poly[(butylene succinate)‐co‐poly(butylene terephthalate)] (PBS–PBT) and poly(tetramethylene glycol) (PTMG) (M_n = 2000) with various compositions were synthesized. PBT content in the PBS was adjusted to ca. 5 mol %. Their thermal and mechanical properties were investigated. In the case of copolymer, the melting point of the PBS–PBT control was 107.8°C, and the melting point of the copolymer containing 70 wt % of PTMG was 70.1°C. Crystallinity of soft segment was 5 ∼ 17%, and that of hard segment was 42 ∼ 59%. The breaking stress of the PBS–PTMG control was 47 MPa but it decreased with increasing PTMG content. In the case of copolymer containing 70 wt % of PTMG, breaking stress was 36 MPa. Contrary to the decreasing breaking stress, breaking strain increased from 300% for PBS–PBT control to 900% for a copolymer containing 70 wt % of PTMG. The shape recovery ratios of the copolymer containing 70 wt % PTMG were almost twice of those of copolymers containing 40 wt % PTMG. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 79: 2067–2075, 2001     

Preparation and characterization of poly(styrene‐b‐butadiene‐b‐styrene)/montmorillonite nanocomposites

With some polymerizable small molecules grafting onto the montmorillonite surface, we disposed the clay through in‐situ emulsion polymerization, and the structure of the modified montmorillonites were studied through Fourier transform infrared spectroscopy (FTIR) and X‐ray diffraction (XRD). The nanocomposites of poly(styrene‐b‐butadiene‐b‐styrene) (SBS)/montmorillonite with excellent mechanical properties were prepared by mixing SBS and the modified montmorillonite on the double rollers at 150°C. The exfoliation of the layered silicates was confirmed by XRD analysis and transmission electron microscopy (TEM) observation. After mechanical kneading of the molten nanocomposites, the exfoliation structure of the silicates is still stable for polystyrene macromolecules grafting onto the silicates. Upon the addition of the modified montmorillonite, the tensile strength, elongation at break and tear strength of the nanocomposites increased from 22.6 MPa to 31.1 MPa, from 608% to 948%, from 45.32 N/mm to 55.27 N/mm, respectively. The low‐temperature point of glass‐transition temperature (T_g) of the products was about −77°C, almost constant, but the high‐temperature point increased from 97°C to 106°C. In addition, the nanocomposites of SBS and modified montmorillonites showed good resistance to thermal oxidation and aging. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers