共查询到20条相似文献,搜索用时 125 毫秒
1.
2.
宽带压控衰减器在现代通信系统中的应用越来越广泛,首先介绍Hittite公司的HMC346型压控衰减器,它具有大动态衰减范围、衰减随控制电压线性变化、优异的输入和输出驻波等特点;然后给出基于HMC346的X波段宽带压控衰减器设计,最后讨论保证设计性能必须考虑的电磁兼容性. 相似文献
3.
本文简要介绍钽酸锂晶体及器件的一些特性,对用该材料制作的21.4MHz宽带滤波器的设计、制作和测试结果作了较详细的介绍,滤波器的带宽达225kHz,矩形系数(BW_(?0dB)/BW_(3dB)为2.66,带外衰减在50dB以上。该材料在做宽带滤波器和压控振荡器方面具有优越性。 相似文献
4.
《固体电子学研究与进展》2013,(6)
提出了一种全新的超宽阻带带阻滤波器结构。该结构由一段加载开路传输线的反向耦合传输线和一对开路传输线并联构成。理论分析表明,通过适当设置电路参数,该滤波器可以产生多个传输零点,构成一个具有高选择性高抑制性的宽带带阻滤波器。通过改变滤波器中的电路参数,特别是其中传输线的特征阻抗,可以灵活地调整滤波器的阻带带宽、阻带衰减和通带性能。基于这一理论,设计了一种宽带带阻滤波器。测试结果表明,该滤波器不仅可以提供109.40%的20dB相对阻带带宽和过渡尖锐的阻带,更可以提供高达105.73%的25dB相对阻带带宽。 相似文献
5.
6.
本文基于三组折叠型谐振结构设计出一款紧凑宽带带阻滤波器。首先,对折叠型谐振结构的特性进行分析,结果表明,该结构具有传输零点,且该传输零点具有可调节性。之后, 通过分析折叠型谐振结构之间的间隔影响,得到较为合适的间距。在此基础上,通过增加另一组折叠型谐振结构的形式,设计得到了宽带带阻滤波器。仿真结果表明,该滤波器的10-dB工作带宽为1.98GHz。通过仿真优化,得到一款采用三组折叠型谐振结构的宽带带阻滤波器。将该滤波器进行加工并测试,结果表明,滤波器的工作带宽为2.41 GHz。此外,为了进一步说明该结构的滤波特性,我们对其等效电路进行了分析。由于采用了折叠型结构,所以这款滤波器具有小型化的特性。 相似文献
7.
《微纳电子技术》2019,(11)
将一种电压阈值型压控双极性忆阻器模型与CMOS反相器进行混合设计,实现了"与"、"或"、"与非"、"或非"基本逻辑门。通过构建"异或"逻辑门新结构,提出一种基于混合忆阻器-CMOS逻辑的全加器电路优化设计方案。最后,分析忆阻器参数β,V_t,R_(on)和R_(off)对电路运算速度和输出信号衰减幅度的影响,研究了该优化设计的电路功能和特性,经验证模拟仿真结果与理论分析结果具有较好的一致性。研究结果表明:全加器优化设计结构更简单,版图面积更小,所需忆阻器数量减少22.2%,CMOS反相器数量减少50%;增大参数β值可提高运算速度,增大忆阻值比率R_(off)/R_(on)可减小逻辑输出信号衰减度。 相似文献
8.
基于单端接地耦合线结合微带传输线加载开路枝节,提出了一款宽带带阻滤波器。该滤波器由输入输出端的单端接地耦合线并联微带传输线上加载三个开路枝节组成。采用奇偶模理论分析、传输线模型和结构模型仿真优化,对滤波器的特性开展了研究。实物加工测试结果与仿真结果的一致性好,验证了所设计的宽带带阻滤波器。该滤波器的阻带中心频率为2 GHz, 3 dB衰减带宽为98%(1.19~3.15 GHz),20 dB衰减带宽为84.5%(1.24~2.93 GHz),阻带带内抑制大于35 dB,结构紧凑,可与航电系统设备板级电路集成,用于电磁干扰防护。 相似文献
9.
10.
11.
A kind of dual-band-stop filter with an unsymmetrical T-shape defected ground structure (DGS) is proposed. The filter has two band gap centers at 4.9 GHz and 7.35 GHz, respectively, where the two centre frequencies are just the second and third harmonics 2.45 GHz. The filters with high band-stop performance and wideband spurious suppression can be achieved by cascading miniaturized unsymmetrical T-shape DGS. The attenuation of three-cascaded T-shape DGS filter is 30.77 dB at 4.9 GHz and 17.96 dB at 7.35 GHz respectively. The above experimental results are in good agreement with the simulation results, especially for the third harmonic. 相似文献
12.
Hao Xin Higgins A. Hacker J. Moonil Kim Rosker M. 《Microwave and Wireless Components Letters, IEEE》2003,13(3):108-110
An electromagnetic crystal (EMXT) with a bandgap around 35 GHz is used as the top and/or bottom walls of a rectangular waveguide. Because of its bandgap, such an EMXT waveguide is a very effective band-stop filter with the rejection band centered at 35 GHz. More than 70 dB of isolation for the rejection band and less than 2 dB of insertion loss for the pass band are measured. Finite element simulation of the EMXT band-stop filter agrees very well with measurements. Using tunable EMXT walls, a band-stop filter with adjustable center frequency and bandwidth can also be realized. 相似文献
13.
提出了一种工作在太赫兹频段, 基于半导体材料锑化铟的超材料带阻滤波器.由于锑化铟材料介电常数的特性, 该滤波器的谐振频率能够进行温度调节.同时, 通过有限积分法和等效LMC电路模型分析了滤波器的几何参数对其谐振频率的影响, 这两种方法得到的结果具有良好的一致性.在温度的取值范围是220~350 K时, 滤波器的谐振频率能够从0.91 THz动态调节到1.28 THz, 并且其阻带谐振频率的透射系数能够有限地被抑制.该滤波器的传输特性在30°入射角范围内具有良好的稳定性.设计的可调超材料带阻滤波器将在太赫兹无线通信、传感等方面有潜在的应用前景. 相似文献
14.
15.
16.
17.
18.
当前移动通信市场对第三代移动通信(简称3G)大力开发与推广的同时对与其相关的通信电缆也提出了更高的要求。针对现有的通信电缆不能满足3G通信对电缆工作频段、衰减、驻波等要求的情况,提出了一款满足3G通信要求的多芯3G数字通信电缆。该3G数字通信电缆对原通信电缆的结构、材料、加工方式等进行了改进,使其很好地达到了3G通信对... 相似文献
19.
本文提出了一种新型的多功能电流模式二阶滤波器电路。该电路基于多端输出电流控制第二代电流传输器,仅需2个MOCCC-II和2个电容,无需元件匹配就能同时实现低通、带通、高通、带阻及全通滤波输出。电路中所有的无源元件均接地,且参数敏感度低。该滤波器可用于通信、电子测量与仪器仪表的信号处理。PSpice仿真结果与理论分析相吻合,验证了该方法的可行性。 相似文献
20.
Attenuation of Communication Signals on Residential and Commercial Intrabuilding Power-Distribution Circuits 总被引:14,自引:0,他引:14
《Electromagnetic Compatibility, IEEE Transactions on》1986,28(4):220-230
The use of electric-power-distribution circuits for intrabuilding communications is ol continued and growing interest. The purpose of this paper is to present intrabuilding signal attenuation measurements taken from five different buildings. The measurements cover the range 20-240 kHz and include transmissions across power phases. The measurements complement earlier measurements by others of power-line impedance and noise. Impedance, attenuation, and noise characterize any communication channel and are needed for design of communication signaling formats, error-control codes, and communication protocols. Except over short distances, attenuation normally exceeds 20 dB, and can be much higher. The attenuation which occurs when the transmitter and receiver use different power-line phases is not always larger than when both are on the same phase. Narrow-band frequency-selective fades can occur and change as network loading changes, and can also exhibit periodic time dependence. Loading, which is time varying, greatly affects signal attenuation between network nodes. The results clearly indicate that power-line signal attenuation is highly variable and unpredictable, is variable with communication signal frequency, and is not easily modeled mathematically. The implications of our results for intrabuilding communications on power-distribution circuits are discussed. 相似文献