Rose Bengal-Cu-TiO2的制备及可见光制氢活性研究

用光还原方法制备了负载Cu的光催化剂Cu-TiO2，并通过染料Rose bengal敏化，制备了具有可见光活性的Rose bengal-Cu-TiO2光催化剂，通过可见光下光解水制氢考察了催化剂的活性，并利用XRD、UV-Vis等手段对样品进行了表征。实验表明：载Cu增强了TiO2对可见光的吸收，Cu负载量对催化剂活性有一定的影响，Cu的最佳负载量为5％（质量分数）。Cu的负载也增加了TiO2对染料的吸附强度和吸附量，从而提高了TiO2对可见光的吸收和光催化活性。但载Cu的TiO2催化剂的活性和传统的载贵金属Pt的TiO2催化剂相比，其光催化活性较低，有待进一步提高．     

可见光响应Pt沉积La2O3/TiO2制备及其对甲苯的光热催化去除

以钛酸四丁酯和硝酸镧为原料,采用溶胶—凝胶法制备La2O3/TiO2,通过光沉积法在La2O3/TiO2表面负载纳米Pt粒子.采用XPS、FTIR、XRD、DRS、TEM和低温氮物理吸附对光催化剂的晶体结构、光谱特征和表面结构进行表征.考察了催化剂在可见光下对甲苯的去除性能和温度对催化剂去除甲苯的影响.结果表明,沉积的Pt以单质和吸附氧的形式存在,其中以吸附氧的形式为主.Pt的掺入没有引起TiO2相结构的变化,减小了晶粒尺寸并增大了催化剂的比表面积.纳米Pt均匀地分布在La2O3/TiO2上,尺寸分布比较均一,大约为5～10nm.Pt-La2O3/TiO2的表面羟基官能团伸缩振动明显增强,比TiO2和La2O3/TiO2具有更高的可见光催化活性.Pt-La2O3/TiO2对甲苯的降解率,随着温度的升高而增大,产生了与光催化作用平行的热催化作用.气相甲苯光热催化过程不是光催化与热催化的简单叠加,而是存在协同作用.     

镍、硫共掺杂纳米TiO2的制备及其可见光催化性能

为提高纳米TiO2的可见光催化活性,采用沉淀-浸渍法制备了一种新型Ni和S共掺杂TiO2纳米复合光催化剂.通过紫外-可见(UV-Vis-)漫反射、X-射线衍射(XRD)、透射电子显微镜(TEM)和X-荧光(EDX)等手段对其结晶形态、晶粒尺寸、元素掺杂量和吸光性能等进行了表征.结果显示,催化剂Ni/S/TiO2为锐钛矿晶相,平均粒径约为6～7nm,比表面积高达260.42m2/g,感光范围可拓展到可见光区,且与纯TiO2,S掺杂TiO2和Ni掺杂TiO2相比,光催化剂Ni/S/TiO2的颗粒粒径更小,比表面积更大,光吸收边红移程度更显著.以活性艳蓝198染料溶液为模拟废水,以氙光灯为光源,对光催化剂Ni/S/TiO2的催化活性进行了评价.结果表明,Ni/S/TiO2具有比纯TiO2、S掺杂TiO2和Ni掺杂TiO2更高的可见光催化活性,氙光灯照射120min,活性艳蓝198降解率可达到98.5%.     

3D Bi12TiO20/TiO2 hierarchical heterostructure: synthesis and enhanced visible-light photocatalytic activities

A three-dimensional (3D) multicomponent oxide, Bi(12)TiO(20)/TiO(2) hierarchical heterostructure was successfully synthesized via a one-step and template-free hydrothermal route. X-ray diffraction and X-ray photoelectron spectroscopy measurements confirm that the composition of the as-fabricated sample is Bi(12)TiO(20)/TiO(2) composite. Scanning and transmission electron microscopy observation reveals that the as-synthesized sample is microsized flower-like hierarchical networks consisted of Bi(12)TiO(20) nanorods decorated with the primary TiO(2) nanoparticles. Extension of the light absorption from the ultraviolet region to the visible-light region was confirmed by UV-vis absorption spectra. Due to the structure-property relationships, the 3D Bi(12)TiO(20)/TiO(2) heterostructure exhibited enhanced visible photocatalytic activity over that of Bi(12)TiO(20) and TiO(2) samples in the decomposition of Rhodamine B in water which is a typical model pollutant. The enhanced photocatalytic activity can be attributed to the extended absorption in the visible light region resulting from the 3D Bi(12)TiO(20)/TiO(2) heterostructures, and the effective separation of photogenerated carriers driven by the photoinduced potential difference generated at the Bi(12)TiO(20)/TiO(2) junction interface, demonstrating that the Bi(12)TiO(20)/TiO(2) heterostructure is a promising candidate as a visible light photocatalyst.     

Recyclable and high-sensitivity electrochemical biosensing platform composed of carbon-doped TiO2 nanotube arrays

Electrode fouling and passivation are the main reasons for attenuated signals as well as reduced sensitivity and selectivity over time in electrochemical analysis. We report here a refreshable electrode composed of carbon-doped TiO(2) nanotube arrays (C-doped TiO(2)-NTAs), which not only has excellent electrochemical activity for simultaneous determination of 5-hydroxytryptamine and ascorbic acid but also can be easily photocatalytically refreshed to maintain the high selectivity and sensitivity. The C-doped TiO(2)-NTAs are fabricated by rapid annealing of as-anodized TiO(2)-NTAs in argon. The residual ethylene glycol absorbed on the nanotube wall acts as the carbon source and no foreign carbon precursor is thus needed. The morphology, structure, and composition the C-doped TiO(2)-NTAs are determined, and the corresponding doping mechanism is investigated by thermal analysis and in situ mass spectroscopy. Because of the high photocatalytic activity of the C-doped TiO(2)-NTAs electrode, the electrode surface can be readily regenerated by ultraviolet or visible light irradiation. This photoassisted regenerating technique does not damage the electrode microstructure while rendering high reproducibility and stability.     

Efficient visible light driven photocatalytic removal of NO with aerosol flow synthesized B, N-codoped TiO2 hollow spheres

In this study, we demonstrate that aerosol assisted flow synthesized B, N-codoped TiO(2) photocatalyst possesses superior photocatalytic activity to pure and single element doped counterparts on the degradation of NO in a flow system under both simulated solar light and visible light irradiation. Characterization results revealed that B, N-codoped TiO(2) photocatalyst was composed of hollow microspheres. Boron and nitrogen were in the form of Ti-O-B and N-Ti-O structures, respectively. The introduction of B and N into the TiO(2) lattice could effectively tune the band gap of TiO(2) and extend its optical response to the visible-light region. The synergistic effect of B and N codoping on visible light driven photocatalytic activity enhancement of TiO(2) was discussed on the basis of experimental results.     

Synthesis and photo-degradation application of WO3/TiO2 hollow spheres

A WO(3)/TiO(2) composite, hollow-sphere photocatalyst with average diameter of 320 nm and shell thickness of 50 nm was successfully prepared using a template method. UV-vis diffuse reflectance spectra illustrated that the main absorption edges of the WO(3)/TiO(2) hollow spheres were red-shifted compared to the TiO(2) hollow spheres, indicating an extension of light absorption into the visible region of the composite photocatalyst. The WO(3) and TiO(2) phases were confirmed by X-ray diffraction analysis. BET isotherms revealed that the specific surface area and average pore diameter of the hollow spheres were 40.95 m(2)/g and 19 nm, respectively. Photocatalytic experiments indicate that 78% MB was degraded by WO(3)/TiO(2) hollow spheres under visible light within 80 min. Under the same conditions, only 24% MB can be photodegraded by TiO(2). The photocatalytic mineralization of MB, catalyzed by TiO(2) and WO(3)/TiO(2), proceeded at a significantly higher rate under UV irradiation than that under visible light, and more significant was the increase in the apparent rate constant with the WO(3)/TiO(2) composite semiconductor material which was 3.2- and 3.5-fold higher than with the TiO(2) material under both UV and visible light irradiation. The increased photocatalytic activity of the coupled nanocomposites was attributed to photoelectron/hole separation efficiency and the extension of the wavelength range of photoexcitation.     

Synthesis and characterization of visible light driven mesoporous nano-photocatalyst MoO3/TiO2

A novel mesoporous-structured photocatalyst MoO3/TiO2 was synthesized through a modified sol-gel method by using P123 as the template, and the resulting nano-photocatalysts were characterized by X-ray diffraction (XRD), N2 adsorption measurements, transmission electron microscope (TEM), UV-vis spectroscopy, XPS and Raman techniques. Low-angle XRD and TEM images show the lack of long-range order in the as-prepared MoO3/TiO2, but the Mo species are homogenously dispersed on the anatase matrix. According to the results of N2 ads-desorption, the calcined products possess the high surface area and the pore size distribution centered between 4-7 nm. The calcined meso-MoO3/TiO2 materials exhibit the high photocatalytic activity for the degradation of MB (methylene blue) under visible light radiation.     

可见光响应型Pt/GaP纳米粉体的光催化性质

利用水合肼液相还原法在纳米磷化镓(GaP)粉体表面沉积贵金属铂(Pt), 制备低Pt担载量Pt(0.80 wt%)/GaP和高Pt担载量Pt(4.2 wt%)/GaP纳米粉体样品. 在可见光照射条件下, 分别以GaP和Pt/GaP纳米粉体作为光催化剂, 对结晶紫水溶液进行光催化降解. 实验结果表明, GaP和Pt/GaP两种纳米粉体皆具有可见光响应光催化性能; Pt担载量对Pt/GaP纳米粉体的光催化性能有着较大的影响, 低Pt担载量Pt(0.80 wt%)/GaP纳米粉体的结晶紫光催化脱色率高于GaP纳米粉体, 而高Pt担载量Pt(4.2 wt%)/GaP粉体的结晶紫光催化脱色率则低于GaP纳米粉体.     

Cyclic performance and photo-induced crystalline growth of nanostructured AgI/TiO2 visible light photocatalyst

Nanostructured AgI/TiO2 visible light photocatalyst was prepared with AgNO3, KI, and Ti(OBu)4 as precursors. The photocatalyst was used repeatedly to degrade methylene blue and methyl orange in water with visible light irradiation. Though a high photocatalytic efficiency was observed for the photocatalyst in the first cycle, the photocatalytic efficiency was found to decrease dramatically in subsequent cycles. X-ray diffraction and SEM analyses revealed an obvious crystalline growth of AgI in AgI/TiO2 nanocomposite after photocatalysis or visible light irradiation. It was proposed that photo-induced crystalline growth had occurred to AgI in the course of photocatalysis and resulted in dramatic decrease in the photocatalytic efficiency of the photocatalyst. Photo-induced crystalline growth may be a limiting factor for the lifetime of photocatalysts and should be examined as an important aspect of photostability when new photocatalysts are developed.     

Oxidation of triclosan by ferrate: reaction kinetics, products identification and toxicity evaluation

The Crystal Violet (CV) dye represented one of the major triphenylmethane dyes used in textile-processing and some other industrial processes. Various metals doped titanium dioxide (TiO(2)) photocatalysts have been studied intensively for the photodegradation of dye in wastewater treatment. In order to understand the mechanistic detail of the metal dosage on the activities enhancement of the TiO(2) based photocatalyst, this study investigated the CV photodegradation reactions under UV light irradiation using a Pt modified TiO(2) photocatalyst. The results showed that Pt-TiO(2) with 5.8% (W/W) Pt dosage yielded optimum photocatalytic activity. Also the effect of pH value on the CV degradation was well assessed for their product distributions. The degradation products and intermediates were separated and characterized by HPLC-ESI-MS and GC-MS techniques. The results indicated that both the N-de-methylation reaction and the oxidative cleavage reaction of conjugated chromophore structure occurred, but with significantly different intermediates distribution implying that Pt doped TiO(2) facilitate different degradation pathways compared to the P25-TiO(2) system.     

A visible light response TiO2 photocatalyst realized by cationic S-doping and its application for phenol degradation

S-doped TiO2 photocatalyst with high visible light activity was prepared by acid catalyzed hydrolysis method using thiourea (TU) as sulfur source. The catalyst was characterized by DRS, XPS, XRD, FTIR, SEM and N2 adsorption. It was found that cation S6+ was homogeneously incorporated into the bulk phase of TiO2 and substitutes for some of the lattice titanium (Ti4+). Doped S can form a new band above the valence band and narrow the band-gap of the photocatalyst, giving rise to a second absorption edge in the visible light region. The activity of the catalyst was examined by photodegradation of phenol in aqueous solution under both artificial visible light and solar light irradiation. The activity of catalyst was found to be dependent on the doping amount of S and the maximum activity was observed when the catalyst was obtained by calcinated at 600 degrees C with the mass ratio of TU/TiO2=1. Too much of new-generated band-gap structures due to higher S-doping could act as recombination centers for electron-hole pairs. Catalyst with optimum S-doping exhibited the highest activity under both artificial light and solar irradiation for phenol degradation. In addition, doped S also beneficial for the better dispersion, large S(BET) and phase transformation retardation of TiO2.     

Pt/Fe_2O_3/TiO_2的制备、表征及其光催化活性研究

报道了担载不同贵金属或过渡金属氧化物的TiO2 催化剂对空气中微量甲醛的光催化氧化的研究结果。实验发现 ,TiO2 上担载Fe2 O3 或Pt时对甲醛均有较高的光催化氧化活性。同时担载双组分的光催化剂Pt Fe2 O3 TiO2 ,由于 2种组分的协同作用 ,具有更高的光催化活性。研究了催化剂制备因素、催化剂的结构及表面特性对催化活性的影响     

复合半导体光催化材料ZnFe2O4-TiO2/SiO2结构与光响应性能研究

采用溶胶．凝胶法制备了负载型复合半导体光催化材料ZnFe2O4-TiO2／SiO2，并通过DTA-TG、XRD、XPS、Raman、TPR及UV-Vis DRS等实验技术对复合材料的晶体结构、表面组成及光响应性能进行了表征和评价．结果表明：ZnFe2O4晶相以高分散状态存在于光催化材料的表面；ZnFe2O4与TiO2复合可使部分Fe^3＋进入体相TiO2的晶格中，促进其由锐钛矿向金红石的相转变，同时表面剩余的少量Zn计聚集形成ZnO物相；TiO2的相变由体相开始，随着ZnFe2O4含量的增加逐渐向表面扩展；SiO2的加入使活性组分更加分散，TiO2平均粒径〈10nm；ZnFe2O4的加入明显拓宽了TiO2的吸光域，并增强了对可见光的吸收．     

纳米α-Fe2O3/TiO2光催化剂的制备及其光催化性能研究

以硝酸铁为铁源,NaOH为沉淀剂合成单分散性良好的纳米α-Fe2O3粒子,然后与纳米TiO2胶体复合制备了纳米α-Fe2O3/TiO2光催化剂。利用动态光散射粒径分析仪、扫描电子显微镜、紫外-可见分光光度计、X射线衍射仪对光催化剂的物相、形貌进行了表征。在室温条件下,以甲醛作为有机污染物,在可见光照射下探讨了纳米α-Fe2O3粒径、α-Fe2O3摩尔分数等对甲醛光催化降解的影响。结果表明,在一定范围内,随着粒径的减小,纳米α-Fe2O3光催化活性增强,在120min内粒径40nm的纳米α-Fe2O3对甲醛的降解效果最好,降解率约为93.05%。与纯TiO2相比,纳米α-Fe2O3/TiO2光催化剂的可见光催化活性明显增强,纳米α-Fe2O3最佳含量为0.20%(摩尔分数)。纳米α-Fe2O3含量过大,纳米α-Fe2O3/TiO2光催化剂的催化活性将降低。     

磁性纳米TiO2／NiFe2O4光催化复合材料的制备及表征

采用均匀沉淀法在磁性NiFe2O4表面包覆TiO2,制备了一种新型纳米TiO2／NiFe2O4光催化复合材料。通过改变Ti和Ni物质量之比确定了复合材料最佳钛镍比,用X射线衍射、透射电镜、UV—vis漫反射、BET、TG—DSC、磁力学测试等手段对复合材料进行了表征,以甲基橙的水溶液为模拟污染物,评价样品的光催化性能：该复合材料在光照2h后,甲基橙的脱色率可达98．5％,是一种在可见光范围内有响应、便于回收、可重复使用的高效光催化剂。     

硫掺杂TiO2/Ti光电极制备及其可见光光电催化性能

为了提高TiO2/Ti光电极在可见光下的光电催化活性,采用阳极氧化法制备了一种新型的硫掺杂TiO2/Ti光电极.采用扫描电子显微镜、X射线衍射、X射线荧光光谱等技术对光电极进行了表面形貌、结晶形态、晶粒尺寸、硫的掺杂量和价态以及吸光性能表征.研究表明:硫掺杂TiO2/Ti光电极的最佳制备条件为:成膜电压160V、电流密度100mA/cm2、Na2SO3质量浓度750mg/L;所制备的光电极具有良好的光电催化氧化降解邻苯二甲酸二甲酯活性,并能有效地矿化其中间产物;与TiO2/Ti电极相比,硫的掺杂可以显著提高其在可见光下的光电催化性能.     

S、RE共掺杂TiO2的制备及其可见光分解水制氢性能

采用溶胶-凝胶法制备了系列稀土(La、Eu、Nd、Tb、Er)和硫共掺杂TiO2光催化剂RE/S/TiO2。通过紫外-可见(UV-Vis)漫反射、X射线衍射(XRD)对催化剂进行了表征。以EDTA为电子给体,考察了光催化剂在可见光照射下的制氢活性。研究结果表明,S/TiO2具有可见光活性,稀土掺杂进一步提高了S/TiO2可见光活性,其活性顺序依次为Eu/S/TiO2>La/S/TiO2>Nd/S/TiO2>Tb/S/TiO2>Er/S/TiO2。与纯TiO2和S/TiO2光催化剂相比,稀土掺杂使催化剂的粒径减小,晶格畸变应力增大,从而提高了催化剂可见光制氢活性。     

非金属掺杂TiO2催化剂的制备及可见光诱导活性

通过金属及非金属离子掺杂改性、离子注入以及染料光敏化等方法可以将只能紫外光激发的TiO2光催化反应红移到可见光区域进行,近年来国内外在非金属掺杂TiO2可见光催化剂研究取得了积极进展。本文主要对N掺杂和C掺杂TiO2的制备方法进行了介绍,同时对其掺杂的非金属存在形态及掺杂机理作了理论分析。     

TiO2光催化活性向可见光区拓展的研究进展

TiO2光催化剂可用于光分解有机污染物,组装太阳能电池,光分解水制氢气或氧气等领域。本文对可见光响应的TiO2光催化剂国内外研究进行了综述,概述了采用敏化,掺杂等方法可使二氧化钛光催化活性从紫外光区拓展到可见光区,并对未来的研究方向进行了展望。