共查询到20条相似文献,搜索用时 203 毫秒
1.
2.
采用传统氧化物陶瓷工艺制备锰锌铁氧体,研究了主配方的氧化铁含量、烧结工艺等因素对材料微观结构和磁导率的影响。结果表明,主配方氧化铁含量在52.2 mol%时,可以获得较好的磁导率温度特性;烧结温度1380℃,保温8~12 h,有助于提高起始磁导率;晶粒直径25μm左右和致密的微观结构,可提高材料的起始磁导率。通过优化配方和制备工艺,开发出了宽温、高磁导率锰锌铁氧体材料RH15K,性能如下:起始磁导率μi:15000±30%(25℃,10 k Hz),μi5000(-40℃,10 k Hz),居里温度TC105℃。 相似文献
3.
采用传统陶瓷工艺制备了NiCuZn铁氧体材料,研究了添加Bi2O3、玻璃对NiCuZn铁氧体材料的磁导率及其温度稳定性和居里温度的影响。研究表明,单独添加Bi2O3时,随着Bi2O3添加量的增加,磁导率先升后降,磁导率的温度系数αμ呈负值且绝对值增大,居里温度TC几乎不变;复合添加等量Bi2O3和玻璃时,磁导率下降,随温度的变化不明显,居里温度TC随添加量增大而先升后降,但添加后的TC均高于不添加的。适量添加Bi2O3、玻璃可以改善材料的温度稳定性。 相似文献
4.
采用传统氧化物陶瓷工艺制备MnZn铁氧体材料。为获得高性能的MnZn软磁铁氧体材料,研究工艺条件及CaO、Nb2O5、Co2O3、TiO2等掺杂对MnZn软磁铁氧体材料增量磁导率的影响。结果表明,适量的CaO掺杂可使铁氧体晶粒尺寸细化,改善铁氧体晶粒的均匀性;适量的Co2O3添加可以改善材料增量磁导率的温度特性;添加适量Nb2O5与TiO2有利于提高起始磁导率、电阻率,降低磁损耗,从而改善材料的直流叠加特性。通过优化掺杂工艺,制备出了高磁导率、宽温、高直流叠加MnZn软磁铁氧体材料。 相似文献
5.
6.
7.
本文扼要地叙述了锰锌铁氧体的烧结机理,针对锰锌铁氧体容易被氧化和还原的特点,介绍了防止锰锌铁氧体氧化和还原的几种方法。根据使用保护气体的原则,采用水蒸汽作保护气体,设计了蒸汽发生装置,制得了起始磁导率μ_(?)≥2000,饱和磁通密度B_(?)≥0.46T,比总损耗P_(?)≤10mW/g,振幅磁导率μ_(?)≥3500,居里温度T_c≥240℃的UY12磁芯。大批生产工艺稳定,是一项颇有经济效益及值得推广的工艺。 相似文献
8.
9.
10.
采用了固相反应法制备了Ni0.24Cu0.21Zn0.55Fe2O4铁氧体材料,研究了制备工艺(预烧温度、烧结温度、升温速度、保温时间)及助熔剂Bi2O3对材料显微结构和电磁性能的影响.结果表明,预烧温度、烧结温度、升温速度、保温时间和助熔剂Bi2O3对NiCuZn铁氧体材料的晶粒尺寸、晶粒分布均匀度、品质因数、起始磁导率和介电常数等影响显著.通过制备工艺参数的优化,确定出适当的工艺条件:预烧温度875℃,烧结温度900℃,升温速度2℃/min,保温时间2h.利用上述工艺制得的材料,不仅具有良好的电磁性能,而且实现了低温烧结. 相似文献
11.
主要介绍了上海宝钢磁业发展有限公司批量生产的高频、高居里温度、超高磁导率锰锌软磁铁氧体材料BRL15K的工艺技术及材料特性。 相似文献
12.
用传统的陶瓷工艺合成Ni0.15Cu0.2+0.02xZn0.65-0.02xFe2O4(x=-2,0,2,4)铁氧体。发现Cu取代Zn对样品的微观结构、居里温度、磁性能和介电性能都有很大的影响。磁导率随x的增大先增大后减小,在x=2时取得最大值。但品质因数始终随x的增大而增大。与此同时,居里温度随x的增大而增高。随着x的增大,介电常数增大;而介电损耗先减小后增大,当x=2时取得最小值。实验结果表明,在x=2时,能制备出高性能的NiCuZn铁氧体材料。 相似文献
13.
14.
15.
介绍了一种高磁导率(μi=2300)、高Bs、高居里温度NiCuZn铁氧体TN230B材料的制备方法及生产过程.研究表明,引入适量的CuO可大大改善材料的电磁性能;通过对原材料的选择,严格控制主配方和制备工艺可获得优良的材料性能. 相似文献
16.
Co-Zn ferrite nano-powder was synthesized using the Microwave- Hydrothermal (M-H) method. The powder was characterized using X-ray diffraction (XRD), Transmission Electron Microscopy (TEM), and Fourier Transform Infrared spectroscopy (FT-IR). The densification of nanoferrites was done using two methods: a) conventional and b) microwave sintering. Electrical and magnetic properties of the sintered samples were measured at room temperature. Electrical properties such as dielectric constant (?'), dissipation factor (D), initial permeability (μi) and quality factor (Q) were measured over a wide frequency range (10 kHz to 1 MHz). The Curie temperature has been determined from the permeability versus temperature plots. It was found that the enhanced electrical and magnetic properties were observed for microwave sintered samples. 相似文献
17.
18.
《IEEJ Transactions on Electrical and Electronic Engineering》2017,12(Z2):S3-S9
In magnetic hyperthermia, the temperature and localization of a ferromagnetic implant in a tumor region is vital in determining the effectiveness of therapeutic heating. We have developed a noninvasive wireless temperature measurement method by utilizing the magnetic permeability property of a ferromagnetic implant with low Curie temperature (FILCT) that varies with the temperature. In clinical settings, when the FILCT is injected into a tumor region, the position of the FILCT is expected to deviate from the central axis of the heating coil (drive coil). When it deviates, the magnetic flux density applied to the FILCT decreases, thus causing difficulty in detecting the temperature of FILCT via a pickup coil and heating of the FILCT at a constant treatment temperature. Therefore, to adjust the magnetic field supply and detection (MFSD) unit to be directly above the FILCT, we propose a position adjustment method by referring to three voltages induced in three pickup coils symmetrically installed inside the drive coil. By using the average value of the three voltages, we also propose a method to estimate the distance between the MFSD unit and the FILCT, which is required for wireless thermometry and determination of the optimal energy applied. The proposed methods are experimentally examined by a verification system. 相似文献
19.
20.
给出一种铁基软磁合金薄带高频磁导率的测量方法,详细介绍了该方法的测量原理,并利用Agilent E4991A射频阻抗/材料分析仪研究了退火温度对20μm厚铁基软磁合金薄带高频磁导率的影响。结果表明,随退火温度的提高,磁导率实部单调提高,磁导率虚部则是先升高后降低。尤其是在550℃下退火,在1MHz和10MHz下样品磁导率实部分别为2210和330;比较了不同温度退火样品的磁导率的测量结果,得知550℃是一个比较理想的退火温度。研究结果对以铁基非晶、纳米晶软磁合金薄带为磁心的高频微电感、微变压器等磁性器件的设计具有重要的指导意义。 相似文献