Structural analyses of RuO<Subscript>2</Subscript>–TiO<Subscript>2</Subscript>/Ti and IrO<Subscript>2</Subscript>–RuO<Subscript>2</Subscript>–TiO<Subscript>2</Subscript>/Ti anodes used in industrial chlor-alkali membrane processes

The morphology and composition of RuO₂–TiO₂/Ti and IrO₂–RuO₂–TiO₂/Ti anodes, which have been used for the production of chlorine for more than 10 years, were analyzed by various methods; such as high-resolution scanning electron microscopy, high-resolution Auger electron spectroscopy, electron probe X-ray emission microanalysis and X-ray diffraction analysis. Drastic changes in the surface morphology, including partial exfoliation of a small amount of the oxide layer and a reduction in the content of ruthenium species through dissolution, were observed for the RuO₂–TiO₂/Ti anode. For the IrO₂–RuO₂–TiO₂/Ti anode, on the other hand, there were moderate changes in the surface morphology and moderate dissolution of iridium and ruthenium species.     

Effect of Zr/Si molar ratio and sulfation on structural and catalytic properties of ZrO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript> mixed oxides

ZrO₂–SiO₂ mixed xerogel and aerogel samples with varied molar ratios were prepared by sol–gel method followed by oven drying and supercritical drying using n-propanol as a solvent, respectively. Sulfation was carried out to further enhance the acidic properties of the mixed oxides. Effect of drying, Zr/Si molar ratio and sulfation have been studied and correlated with the structural, textural and catalytic properties of ZrO₂–SiO₂ mixed oxides. Both xerogel and aerogel mixed oxides have different structural and textural features, however, the total number of acid sites per unit surface area (0.0021–0.0029 mmol NH₃ m⁻²) and thus the catalytic activity for cyclohexanol conversion (31–41%) was found in the similar range. Sulfated mixed oxide aerogel and xerogel samples showed significant enhancement of cyclohexanol conversion (91–99%).     

Vitreous region and properties of glasses of the Ga<Subscript>2</Subscript>S<Subscript>3</Subscript>–GeS<Subscript>2</Subscript>–PbF<Subscript>2</Subscript> system

Vitrification in the Ga₂S₃–GeS₂–PbF₂ system is considered. The physicochemical properties of glasses, such as density, microhardness, electroconductivity, refraction index, and transmission percentage of specimens in visible and IR ranges of spectrum are studied; differential thermal analysis is carried out; and Raman and electron paramagnetic resonance spectra are investigated.     

Physical–chemical properties and conductivity of Na<Subscript>2</Subscript>O–SnO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript> glass systems

The effect of tin(IV) oxide on the conductivity and chemical stability of sodium–silicate glass has been studied for five different glass compositions. Dilatometry and DSC were used to investigate the thermal behavior of the glass. The research into transport characteristics of the glass has shown that its conductivity is in the range of 2 × 10^–8–5 × 10^–7 S/cm at 25°C and 10^–3 S/cm at 300°C.     

Synthesis and physicochemical properties of a solid oxide nanocomposite based on a ZrO<Subscript>2</Subscript>–Y<Subscript>2</Subscript>O<Subscript>3</Subscript>–Gd<Subscript>2</Subscript>O<Subscript>3</Subscript>–MgO system

A highly dispersive powder with a (ZrO₂)_0.92(Y₂O₃)_0.03(Gd₂O₃)_0.03(MgO)_0.02 composition and specific surface area of 150 m²/g has been synthesized via a method of coprecipitation of hydroxides with the subsequent cryochemical treatment of the gel. Nanoceramics based on the cubic modification of zirconium dioxide with the grain size of ~40–45 nm have been obtained. The temperature dependence of the specific electrical conductance of the nanoceramics within a temperature range of 350–870°C in air has been studied, and the ratio of the ionic and electronic parts of the conductance has been determined. Recommendations for the use of the obtained oxide nanocomposite as an electrolyte for a high-temperature fuel cell have been given.     

Effect of the thermal treatment on the phase composition of the surface of coatings based on Si–B–ZrB<Subscript>2</Subscript> and modified with ZrO<Subscript>2</Subscript> fibers

Coatings on graphite that are stable to oxidation and based on the silicon–boron–zirconium boride composite containing from 5 to 50% of fibrous zirconium dioxide as a modifying dopant have been produced by the suspension–annealing method. A nonporous layer is formed at the zirconium dioxide content ranging from 5 to 15%, while a porous layer is formed at its 50% content. A glass-forming melt, as well as zirconium dioxide and silicate, is formed during thermal treatment as a result of the chemical reactions with the oxygen in air. The zirconium silicate content increases, along with the modifier’s concentration and temperature.     

Effect of iron oxide (Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>) on the structural,optical, electrical,and dielectric properties of SrO–V<Subscript>2</Subscript>O<Subscript>5</Subscript> glasses

The oxide glass system of the composition (10 – x)SrO–xFe₂O₃–90V₂O₅, (x = 0, 2, 4, 6 and 8 mol %) were prepared by a standard melt quenching technique. The amorphous nature of the prepared glass was confirmed using X-ray diffraction technique. The infrared spectra of these glasses were recorded over a continuous spectral range (850–1500 cm^–1). The density of prepared sample was obtained by the Archimedes principle. The physical parameters of the glasses were also determined with respect to the composition. Density increases from 3.10 to 3.20 g/cm³, whereas the molar volume decreases with the increase in Fe₂O₃ concentration. In order to study optical properties, absorption spectra were measured at room temperature. Indirect optical energy band gap, optical dielectric constant, refractive index were calculated from optical energy band gap. The refractive index decreases gradually with the increase in Fe₂O₃ content due to increase of bridging oxygen’s. For temperatures from 300 to 500 K, the dc conductivity increased with the increasing Fe₂O₃ content. The dielectric properties like dielectric constant, dielectric loss factor and dielectric loss tangent investigated at the room temperature in the frequency range of 10 kHz to 1 MHz decreases with frequency. The dielectric behavior shows strong frequency as well as composition dependence.     

Effects of the geometry and operating temperature on the stability of Ti/IrO<Subscript>2</Subscript>–SnO<Subscript>2</Subscript>–Sb<Subscript>2</Subscript>O<Subscript>5</Subscript> electrodes for O<Subscript>2</Subscript> evolution

Ternary IrO₂–Sb₂O₅–SnO₂ anode has shown its superiorities over IrO₂ and many other electrocatalysts for O₂ evolution, in terms of electrochemical stability, activity and cost. The performance of IrO₂–Sb₂O₅–SnO₂ anodes is affected by its electrochemical properties and operating conditions. In this paper, the electrochemical stability and activity of the Ti/IrO₂–Sb₂O₅–SnO₂ anodes prepared with three different geometries were investigated under different operating conditions. It was found that anodes with large mean curvature have high electrochemical stability. Although increasing temperature results in a decrease in the stability of Ti/IrO₂–Sb₂O₅–SnO₂, the anode with a mean curvature of 200 m⁻¹ still shows acceptable service life even at 70 °C. This tolerance of high temperature was attributed to the thermal expansion difference between the substrate and the coating layer, the redox window for Ir(V)/Ir(IV) conversion, and the redox reversibility of Sb and Sn species in the coating layer.     

Effect of Field Strength and Electronegativity of CaO and MgO on Structural and Optical Properties of SiO<Subscript>2</Subscript>–K<Subscript>2</Subscript>O-CaO-MgO Glasses

The glass composition 55 SiO₂-10 K₂O-(35-x) CaO-(x) MgO (0 ≤ x ≤ 30) is prepared by the melt quenched technique. The as prepared samples are characterized by X-ray diffraction, Fourier Transform-Infrared Spectroscopy (FT-IR) and UV-Visible reflectance spectroscopy. The MgO containing glasses show better polymerization (cross-linking) and have a compact glass network as compared to CaO containing glass. Interestingly, some weak bonds are observed around 1393, 1461 and 1530 cm^-1 in FT-IR spectra related to Ca/Mg-O-H. The optical band gap of the series varies from 3.42 eV to 3.72 eV, indicating wide-band gap materials that could be used in non-linear optical applications.     

Study on flame structures and emissions of CO and NO in Various CH<Subscript>4</Subscript>/O<Subscript>2</Subscript>/N<Subscript>2</Subscript>–O<Subscript>2</Subscript>/N<Subscript>2</Subscript> counterflow premixed flames

An oxygen-diluted partially premixed/oxygen-enriched supplemental combustion (ODPP/OESC) counterflow flame is studied in this paper. Flame images are obtained through experiments and numerical simulations with the GRI-Mech 3.0 chemistry. The oxygen dilution effects are revealed by comparing the flame structures and emissions with those of a premixed flame and partially premixed flame (PPF) at the same equivalence ratio (?_Σ = 0.95 and ? _f = 1.4). The results show that both PPF and ODPP/OESC flames have distinct double flame structures; however, the location of the premixed combustion zone and the distance between premixed/nonpremixed combustion zone are significantly different for these two cases. For the ODPP/OESC flame, the temperature in the premixed combustion zone is lower and the premixed zone itself is located farther downstream from the fuel nozzle, which leads to reduction of NO and CO emissions, as compared to those of the PPF. Therefore, by adjusting the distribution of the oxygen concentration in the premixed and nonpremixed combustion zones, the ODPP/OESC can effectively balance the chemical reaction rate in the entire combustion zone and, consequently, reduce emissions.     

Influence of Calcination Temperature on Activity and Selectivity of Ni–CeO<Subscript>2</Subscript> and Ni–Ce<Subscript>0.8</Subscript>Zr<Subscript>0.2</Subscript>O<Subscript>2</Subscript> Catalysts for CO<Subscript>2</Subscript> Methanation

Herein, we studied the influence of calcination temperature (500–800 °C) of Ni/CeO₂ and Ni/Ce_0.8Zr_0.2O₂ catalysts on the specific surface area, pore volume, crystalline size, lattice parameter, chemical bonding and oxidation states, nickel dispersion and CH₄/CO production rate in CO₂ methanation. In general, the catalytic performance revealed that Zr doping catalysts could increase the CH₄ production rate. Combined with the production rate and the characterizations results, we found that the combination of nickel dispersion, peak area of CO₂–TPD and O_II/(O_II + O_I)) play the critical role in increasing the CH₄ production rate. It is well to be mentioned that the CO production rate is strongly influenced by the nickel dispersion. Furthermore, the in-situ DRIFTS confirmed that the CO originates from the decomposition of H-assisted formate species.     

Formation and stability of glasses with ultra-optical properties in TiO<Subscript>2</Subscript>–Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>–PbO system

To obtain ultra-optical property in glasses, as the basis for photonic applications, the glass forming region of TiO₂–Bi₂O₃–PbO system was investigated and determined by melting series of compositions in the system. The glass-forming boundary region was defined. The best compositions for glass formation were found to be around the eutectic and peritectic regions in the corresponding phase diagram. Generally, stability increased with the addition of TiO₂, acting as a conditional glass former, to a maximum of 15TiO₂ mol %. Replacing PbO with Bi₂O₃ in the glass worsened the stability, due to the increase of heavy cation Bi^3– in the glass structure. Finally, the refractive index and dispersion of some stable glasses were measured, which were as high as 2.435 and 10.2, respectively.     

Optimization of Ti/SnO<Subscript>2</Subscript>–Sb<Subscript>2</Subscript>O<Subscript>5</Subscript> anode preparation for electrochemical oxidation of organic contaminants in water and wastewater

The preparation of antimony-doped tin oxide anodes on a titanium substrate (Ti/SnO₂–Sb₂O₅ anodes) by dipping in a solution of tin chloride and antimony chloride and annealing at high temperatures was optimized for the potential applications of drinking water disinfection, wastewater effluent disinfection, and industrial waste stream treatment. The effectiveness of Ti/SnO₂–Sb₂O₅ anodes prepared under different conditions was evaluated by using hexanol as a probe molecule to measure the extent of oxidative reactions, and anode performance was monitored by cyclic voltammetry. A large factorial matrix consisting of tin chloride concentration × antimony chloride concentration × annealing temperature was first evaluated, and the optimum conditions were found to be 20% tin chloride and 1% antimony chloride in the dip solution and an annealing temperature of 500°C. Further investigation showed that the rate of withdrawal from the dip solution, the number of coatings of the dip solution, and the addition of oxygen during annealing did not significantly affect anode performance. Under optimum preparation conditions, Ti/SnO₂–Sb₂O₅ anodes showed no loss of performance over 1,280 cycles of cyclic voltammetry, suggesting that their performance can be sustained over long periods of use. The result of this research is a simple preparation method for effective and long-lived Ti/SnO₂–Sb₂O₅ anodes; this method could be easily adopted by a utility for pilot- or full-scale disinfection of water and wastewater and the treatment of industrial waste streams.     

Synthesis and properties of binary spinels in a NiO–CuO–Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>–Cr<Subscript>2</Subscript>O<Subscript>3</Subscript> system

The conditions for the formation of a spinel structure from a NiO–CuO–Fe₂O₃–Cr₂O₃ oxide mixture using several technological approaches have been examined. Addition of KCl is accompanied with the formation of two spinel-like phases, whereas in the absence of KCl just one solid solution of nickel–copper ferrite–chromite with the structure of a cubic spinel is formed. At the temperature of thermal treatment of 900°C, the presence of an admixture phase of the delafossite (CuCrO₂) type was established. The conditions for the fabrication of samples containing two spinel phases (cubic and tetragonal) characterized with the most developed surface and manifesting = increased catalytic activity in the reaction of the decomposition of an organic substance by hydrogen peroxide have been formulated. The studied features of spinel synthesis can be of interest for developing materials with an active surface promising for application as adsorbents of catalysts and sensors.     

Synthesis of the study of solid solutions based on the ZrO<Subscript>2</Subscript>–HfO<Subscript>2</Subscript>–Y<Subscript>2</Subscript>O<Subscript>3</Subscript>(CeO<Subscript>2</Subscript>) system

The results of the studies of the conditions of the liquid-phase synthesis of highly dispersed xerogels with a low degree of agglomeration and precursor nanopowders (~10–12 nm) based on zirconium dioxide in the ZrO₂–HfO₂–Y₂O₃(CeO₂) system are presented. The thermal decomposition of xerogels and formation of crystalline solid solutions with the structure of fluorite are investigated. The optimal conditions for the solidification of nanodispersed powders for fabricating compact ceramics based on solid solutions of ZrO₂ and the physical–chemical properties of these ceramics are studied.     

Effect of the relative volume of the conducting phase on the electroconductivity of glasses in the Na<Subscript>2</Subscript>O–B<Subscript>2</Subscript>O<Subscript>3</Subscript>–SiO<Subscript>2</Subscript> system

The effect of the relative volume of the conducting phase on the electroconductivity of phase-separated glasses in the ternary system Na₂O–B₂O₃–SiO₂, whose compositions are on the same glass transition isotherm at 550°C, is investigated. It is demonstrated that the electroconductivity of phase-separated sodium borosilicate glasses does not depend on the relative volume of the conducting phase (within the limits from 0.3 to 0.9) under the condition that its composition invariable.