Structural and optical properties of Er-doped Y2Ti2O7 thin films by sol-gel method

Er³⁺-doped Y₂Ti₂O₇ and Er₂Ti₂O₇ thin films were fabricated by sol-gel spin-coating method. A well-defined pyrochlore phase Er_xY_2-xTi₂O₇ was observed while the annealing temperature exceeded 800 °C. The average transmittance of the Er_xY_2-xTi₂O₇ thin films annealed at 400 to 900 °C reduces from ∼ 87 to ∼ 77%. The refractive indices and optical band gaps of Er_xY_2-xTi₂O₇ (x = 0-2) annealed at 800 °C/1 h vary from 2.20 to 2.09 and 4.11 to 4.07 eV, respectively. The ∼ 1.53 μm photoluminescence spectrum of Er³⁺ (5 mol%)-doped Y₂Ti₂O₇ thin films annealed at 700 °C/1 h exhibits the maximum intensity and full-width at half maximum (∼ 60 nm).     

Effect of substrate temperatures on the optical properties of evaporated Sc2O3 thin films

Scandium oxide (Sc₂O₃) films were deposited by electron beam evaporation with substrate temperatures varying from 50 to 350 °C. X-ray diffraction, scanning electron microscopy, spectrometer, and optical profilograph were employed to investigate the structural and optical properties of the films. The refractive index and extinction coefficient were calculated from the transmittance and reflectance spectra, and then the energy band gaps were deduced and discussed. Laser induced damage threshold of the films were also characterized. Optical and structural properties of Sc₂O₃ films were found to be sensitive to substrate temperature.     

Influence of Nb dopant on the structural and optical properties of nanocrystalline TiO2 thin films

In this study, preparation of Nb-doped (0-20 mol% Nb) TiO₂ dip-coated thin films on glazed porcelain substrates via sol-gel process has been investigated. The effects of Nb on the structural, optical, and photo-catalytic properties of applied thin films have been studied by X-ray diffraction, Raman spectroscopy, and scanning electron microscopy. Surface topography and surface chemical state of thin films was examined by atomic force microscope and X-ray photoelectron spectroscopy. XRD and Raman study showed that the Nb doping inhibited the grain growth. The photo-catalytic activity of the film was tested on degradation of methylene blue. Best photo-catalytic activity of Nb-doped TiO₂ thin films were measured in the TiO₂-1 mol% Nb sample. The average optical transmittance of about 47% in the visible range and the band gap of films became wider with increasing Nb doping concentration. The Nb⁵⁺ dopant presented substitutional Ti⁴⁺ into TiO₂ lattice.     

The effect of heat treatment on physical properties of nanograined (WO3)1-x-(Fe2O3)x thin films

Thin films of (WO₃)_1-x-(Fe₂O₃)_x composition were deposited by thermal evaporation on glass substrates and then all samples were annealed at 200-500 °C in air. Optical properties such as transmittance, reflectance, optical bangap energy, and the optical constants of the “as deposited” and the annealed films were studied using ultraviolet-visible spectrophotometry. It was shown that the annealing process changes the film optical properties which were related to Fe₂O₃ concentration. Moreover, using X-ray photoelectron spectroscopy, we have indicated that WO₃ is stoichiometric, while iron oxide was in both FeO and Fe₂O₃ compositions so that the FeO composition converted to Fe₂O₃ after the annealing process. Using atomic force microscopy, it was observed that surface of the “as deposited” films were smooth with a nanometric grain size. The film surface remained unchanged after annealing up to 300 °C. Surface roughness and the grain size of the films with x = 0, 0.05, and 0.75 highly increased at higher annealing temperatures (400 and 500 °C), but were nearly unchanged for medium x-values (0.3 and 0.4).     

Structural and optical properties of rock-salt Cd1 − xZnxO thin films prepared by thermal decomposition of electrodeposited Cd1 − xZnxO2

Cd_1 − xZn_xO nanocrystalline thin films with rock-salt structure were obtained through thermal decomposition of Cd_1 − xZn_xO₂ (x = 0, 0.37, 0.57, 1) thin films which were electrodeposited from aqueous solution at room temperature. X-ray diffraction results showed that the Zn ions were incorporated into rock salt-structure of CdO and the crystal lattice parameters decreased with the increase of Zn contents. The bandgaps of the Cd_1 − xZn_xO thin films were obtained from optical transmission and were 2.40, 2.51, 2.63 and 3.25 eV, respectively.     

Structural and optical studies of nanocrystalline V2O5 thin films

We report the structural and optical properties of nanocrystalline thin films of vanadium oxide prepared via evaporation technique on amorphous glass substrates. The crystallinity of the films was studied using X-ray diffraction and surface morphology of the films was studied using scanning electron microscopy and atomic force microscopy. Deposition temperature was found to have a great impact on the optical and structural properties of these films. The films deposited at room temperature show homogeneous, uniform and smooth texture but were amorphous in nature. These films remain amorphous even after postannealing at 300 °C. On the other hand the films deposited at substrate temperature T_S > 200 °C were well textured and c-axis oriented with good crystalline properties. Moreover colour of the films changes from pale yellow to light brown to black corresponding to deposition at room temperature, 300 °C and 500 °C respectively. The investigation revealed that nanocrystalline V₂O₅ films with preferred 001 orientation and with crystalline size of 17.67 nm can be grown with a layered structure onto amorphous glass substrates at temperature as low as 300 °C. The photograph of V₂O₅ films deposited at room temperature taken by scanning electron microscopy shows regular dot like features of nm size.     

Structural characterization and novel optical properties of defect chalcopyrite ZnGa2Te4 thin films

Stoichiometric thin film samples of the ternary ZnGa₂Te₄ defect chalcopyrite compound were prepared and characterized by X-ray diffraction technique. The elemental chemical composition of the prepared bulk material as well as of the as-deposited film was determined by energy-dispersive X-ray spectrometry. ZnGa₂Te₄ thin films were deposited, by conventional thermal evaporation technique onto highly cleaned glass substrates. The X-ray and electron diffraction studies revealed that the as-deposited and the annealed ZnGa₂Te₄ films at annealing temperature t_a ≤ 548 K are amorphous, while those annealed at t_a ≥ 573 K (for 1 h), are polycrystalline. The optical properties of the as-deposited films have been investigated for the first time at normal incidence in the spectral range from 500 to 2500 nm. The refractive index dispersion in the transmission and low absorption region is adequately described by the Wemple–DiDomenico single oscillator model, whereby, the values of the oscillator parameters have been calculated. The analysis of the optical absorption coefficient revealed an in-direct optical transition with energy of 1.33 eV for the as-deposited sample. This work suggested that ZnGa₂Te₄ is a good candidate in solar cell devices as an absorbing layer.     

Structure, morphology and optical properties of nanocrystalline yttrium oxide (Y2O3) thin films

Yttrium oxide (Y₂O₃) thin films were grown onto Si(1 0 0) substrates using reactive magnetron sputter-deposition at temperatures ranging from room temperature (RT) to 500 °C. The effect of growth temperature (T_s) on the growth behavior, microstructure and optical properties of Y₂O₃ films was investigated. The structural studies employing reflection high-energy electron diffraction RHEED indicate that the films grown at room temperature (RT) are amorphous while the films grown at T_s = 300-500 °C are nanocrystalline and crystallize in cubic structure. Grain-size (L) increases from ∼15 to 40 nm with increasing T_s. Spectroscopic ellipsometry measurements indicate that the size-effects and ultra-microstructure were significant on the optical constants and their dispersion profiles of Y₂O₃ films. A significant enhancement in the index of refraction (n) (from 2.03 to 2.25) is observed in well-defined Y₂O₃ nanocrystalline films compared to that of amorphous Y₂O₃. The observed changes in the optical constants were explained on the basis of increased packing density and crystallinity of the films with increasing T_s. The spectrophotometry analysis indicates the direct nature of the band gap (E_g) in Y₂O₃ films. E_g values vary in the range of 5.91-6.15 eV for Y₂O₃ films grown in the range of RT-500 °C, where the lower E_g values for films grown at lower temperature is attributed to incomplete oxidation and formation of chemical defects. A direct, linear relationship between microstructure and optical parameters found for Y₂O₃ films suggest that tuning optical properties for desired applications can be achieved by controlling the size and structure at the nanoscale dimensions.     

Structural and optical properties of nanocrystalline CdS thin films prepared using microwave-assisted chemical bath deposition

Cadmium sulfide (CdS) nanocrystalline thin films were prepared using the microwave-assisted chemical bath deposition method onto glass substrates at 80 °C. Aqueous solutions of either cadmium chloride or cadmium acetate and thiourea were used as sources of Cd²⁺ and S²⁻ ions, respectively. Two sets of samples with different concentrations were prepared. A microwave oven was used as a heating source to synthesize the nanocrystalline CdS thin films. The prepared thin films had a good adhesion with no pinholes. These films were examined for their structural and surface morphologies by X-ray diffraction (XRD), scanning electron microscopy, and atomic force microscopy. The optical properties were investigated using UV-vis spectrophotometer, photoluminescence, and Raman spectroscopy. Particle size values obtained from XRD were compared with these calculated using effective mass models. The values of optical band gaps according to optical transmission measurements decreased as the ion source molar concentration increased.     

Structural and optical properties of heteroepitaxial beta Ga2O3 films grown on MgO (100) substrates

Gallium oxide (Ga₂O₃) films were deposited on MgO (100) substrates by metalorganic vapor phase epitaxy. Structure analyses showed that the films deposited at 550-700 °C were epitaxial β-Ga₂O₃ films with an out of plane relationship of β-Ga₂O₃(100)||MgO(100). The film deposited at 650 °C showed the best crystallinity and the microstructure of the film was investigated by high resolution transmission electron microscopy. A theoretical model of the growth mechanism was proposed and the in-plane epitaxial relationship was given to be β-Ga₂O₃[001]||MgO<011>. A four-domain structure inside the epitaxial film was clarified. The β-Ga₂O₃ film deposited at 650 °C showed an absolute average transmittance of 95.9% in the ultraviolet and visible range, which had an optical band gap of 4.87 eV.     

Composition dependence of structural and optical properties of Ba(Zrx,Ti1-x)O3 thin films grown on MgO substrates by pulsed laser deposition

Ba(Zr_x,Ti_1-x)O₃ (BZT) films with Zr concentration ranging from 0 to 40% were grown on MgO single crystal substrates by pulsed laser deposition, and their optical properties in the visible range were systematically characterized. A linear increase in the out-of-plane lattice constant of BZT unit cell with increasing Zr content was detected by X-ray diffraction. The surface morphology was observed by atomic force microscopy and the grain size was shown to increase with Zr concentration. Prism coupling and UV-visible transmission spectroscopy techniques were used to analyze the optical properties of the films. Refractive index between 2.15 and 2.3 was observed at 633 and 1547 nm respectively, which decreased with rising Zr content. The BZT films also possessed large optical band gap energy up to 3.92 eV, which increased with rising Zr content. Quadratic electro-optic effect was observed with electro-optic coefficients between 0.11 and 0.81 × 10^− 18 m²/V², which decreased with Zr concentration. Optical loss was estimated from scattering and absorption, and the absorption coefficient dropped with increasing Zr content at near band gap. The obtained results provide information for the design of BZT thin film-based optical devices.     

Characterization of Al2O3/ZrO2 nano multilayer thin films prepared by pulsed laser deposition

Microstructural characterization of pulsed laser deposited Al₂O₃/ZrO₂ multilayers on Si (1 0 0) substrates at an optimized oxygen partial pressure of 3 × 10⁻² mbar and at room temperature (298 K) has been carried out. A nanolaminate structure consisting of alternate layers of ZrO₂ and Al₂O₃ with 40 bi-layers was fabricated at different zirconia layer thicknesses (20, 15 and 10 nm). The objective of the work is to study the effect of ZrO₂ layer thickness on the stabilization of tetragonal ZrO₂ phase for a constant Al₂O₃ layer thickness of 5 nm. The Al₂O₃/ZrO₂ multilayer films were characterized using high temperature X-ray diffraction (HTXRD) in the temperature range 298–1473 K. The studies showed that the thickness of the zirconia layer has a profound influence on the crystallization temperature for the formation of tetragonal zirconia phase. The tetragonal phase content increased with the decrease of ZrO₂ layer thickness. The cross-sectional transmission electron microscope (XTEM) investigations were carried out on a multilayer thin films deposited at room temperature. The XTEM studies showed the formation of uniform thickness layers with higher fraction of monoclinic and small fraction of tetragonal phases of zirconia and amorphous alumina.     

VO2 thin films deposited on silicon substrates from V2O5 target: Limits in optical switching properties and modeling

Thermochromic VO₂ thin films presenting a phase change at T_c = 68 °C and having variable thickness were deposited on silicon substrates (Si-001) by radio-frequency sputtering. These thin films were obtained from optimized reduction of low cost V₂O₅ targets. Depending on deposition conditions, a non-thermochromic metastable VO₂ phase might also be obtained. The thermochromic thin films were characterized by X-ray diffraction, atomic force microscopy, ellipsometry techniques, Fourier transform infrared spectrometry and optical emissivity analyses. In the wavelength range 0.3 to 25 μm, the optical transmittance of the thermochromic films exhibited a large variation between 25 and 100 °C due to the phase transition at T_c: the contrast in transmittance (difference between the transmittance values to 25 °C and 100 °C) first increased with film thickness, then reached a maximum value. A model taking into account the optical properties of both types of VO₂ film fully justified such a maximum value. The n and k optical indexes were calculated from transmittance and reflectance spectra. A significant contrast in emissivity due to the phase transition was also observed between 25 and 100 °C.     

Determination of optical constants and thicknesses of In2O3:Sn films from transmittance data

Indium tin oxide (ITO) thin films were deposited on quartz substrates by direct current magnetron sputtering and annealed in N₂ and air. The normal incidence transmittance of the films was measured by a spectrophotometer. The electrical parameters such as carrier concentration, mobility and resistivity were investigated by van der Pauw method. An optical model has been proposed to simulate the optical constants and thicknesses of the films from transmittance data, which combines the Forouhi-Bloomer model and modified Drude model. The relaxation energy in the Drude term is taken as energy-dependent for a better fitting in the visible spectral range. The simulated transmittance is in good agreement with the measured spectrum in the whole measurement wavelength range. The electrical parameters obtained from the optical simulation are well consistent with those measured electrically by van der Pauw method. The experimental results also indicate that the different post-deposition annealing treatments yield the distinct optical and electrical properties of ITO films.     

Structural and dielectric properties of LuFe2O4 thin films grown by pulsed-laser deposition

Epitaxial LuFe₂O₄ thin films are deposited on sapphire substrate by pulsed-laser deposition. Different growth conditions are tackled and it is found that substrate temperature is the most critical condition for the film growth; while below 750 °C the film crystallization is poor. The Lu:Fe ratio is also found to be important in forming the LuFe₂O₄ phase in the films; while higher content of Fe oxide than that of stoichiometric LuFe₂O₄ in the target is favorable for the formation of the LuFe₂O₄ phase. However, impurity phases such as Fe₃O₄ and Fe₂O₃ are induced in the film with a Fe oxide enriched target. A large dielectric tunability under electric field is revealed in the film; while the dielectric tunability decreases as the frequency increases, and eventually the dielectric tunability disappears above 500 MHz.     

Structural and optical properties of pulsed laser deposited V2O5 thin films

Pulsed laser deposited nanocrystalline V₂O₅ thin films were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), high-resolution transmission electron microscopy (HRTEM) and optical spectroscopy. The films were deposited on amorphous glass substrates, keeping the O₂ partial pressure at 13.33 Pa and the substrate temperature at 220 °C. The characteristics of the films were changed by varying the laser fluence and repetition rate. XRD revealed that films are nanocrystalline with an orthorhombic structure. XPS shows the sub-stoichiometry of the films, that generally relies on the fact that during the formation process of V₂O₅ films, lower valence oxides are also created. From the HRTEM images, we observed the size evolution and distribution characteristics of the clusters in the function of the laser fluence. From the spectral transmittance we determined the absorption edge using the Tauc plot. Calculation of the Bohr radius for V₂O₅ is also reported.     

Preparation of LiMn2O4 thin films by aqueous solution deposition

Cathode material LiMn₂O₄ thin films were prepared by aqueous solution deposition using lithium acetate and manganese acetate as starting materials. The structures, morphologies, and the first discharge specific capacity of the thin films were investigated as a function of annealing temperature and time. The cycling properties of the thin films were also examined. The results show that LiMn₂O₄ thin films prepared by this method are homogenous and crack-free. The thin film annealed at 750°C for 30 min has good rechargeability. The capacity loss per cycle is about 0.05% after being cycled 100 times.     

Structural, optical and electrical properties of reactively sputtered Ag2Cu2O3 films

Ag₂Cu₂O₃ thin films were deposited on glass substrates by RF magnetron sputtering of an equiatomic silver-copper target (Ag_0.5Cu_0.5) in reactive Ar-O₂ mixtures. The reactive sputtering was done at varying power, oxygen flow rate and deposition temperature to study the influence of these parameters on the deposition of Ag₂Cu₂O₃ films. The film structure was determined by X-ray diffraction, while the optical properties were examined by spectrophotometry (UV-vis-NIR) and photoluminescence. Furthermore, the film thickness and resistivity were measured by tactile profilometry and 4-point probe, respectively. Additional mobility, resistivity and charge carrier density Hall effect measurements were done on a few selected samples. The best films in terms of stoichiometry and crystallography were achieved with a sputtering power of 100 W, oxygen and argon flow rates of 20 sccm (giving a deposition pressure of 1.21 Pa) and a deposition temperature of 250 °C. The optical transmittance and photoluminescence spectra of films deposited with these parameters indicate several band gaps, most prominently, a direct one of around 2.2 eV. Electrical characterization reveals charge carrier concentrations and mobilities in the range of 10²¹-10²² cm^− 3 and 0.01-0.1 cm²/Vs, respectively.     

Effect of thermal annealing time on optical and structural properties of TeO2 thin films

TeO₂ thin films were deposited on quartz substrates by rf reactive sputtering technique from a Te metal target. The obtained samples were annealed in an argon atmosphere at 450 °C for different annealing times up to 90 min. X-ray diffraction studies revealed that the as-grown samples were amorphous and there was no appreciable change in structure for a short annealing time. Thin films became polycrystalline with the tetragonal (α-phase) structure of tellurium dioxide crystal with the increase of the thermal annealing time. The refractive index and optical energy gap of the films were calculated by modelling transmittance spectra. The optical energy gap decreased continuously from 3.83 eV to 3.71 eV with increasing thermal annealing time.     

Synthesis by an ionic liquid-assisted method and optical properties of nanoflower Y2O3

Flower-like Y₂O₃ nano-/microstructured phosphors without metal activators have successfully been fabricated by an ionic liquid (IL)-assisted method involving temperature (600 °C) annealing. In this paper, the effect of IL concentration on the morphology of the product has been investigated. The IL plays a crucial role in the formation of various morphologies of Y₂O₃. The structural and morphological features of the obtained samples have been characterized by means of X-ray powder diffraction (XRD) analysis, photoluminescence spectra (PL), Fourier-transform infrared (FT-IR) spectra and X-ray photoelectron spectra (XPS). The photoluminescence spectra of the products exhibit an intense bluish-white emission (ranging from 405 to 430 nm and centered at 418 nm). The luminescent mechanisms have been ascribed to the carbon impurities in the Y₂O₃ host. The effect of the ILs cation and the counter anions on the Y₂O₃ morphology of these nanostructures was studied experimentally. It was observed that Y₂O₃ morphology and PL of these nanostructures were strongly influenced by the type of cation and anion. As the length of the subsidiary chain of cation section of IL (imidaziole ione) reduces, the thickness of the nano-sheets increases. It is expected that the present method may easily be extended to similar nano-/microstructures of other oxide materials. Such investigations are currently underway.