Measurement of the <Superscript>137</Superscript>Cs concentration by its own β-radiation using liquid scintillation spectrometry

The possibility of measuring the ¹³⁷Cs concentration in seawater by its own β-radiation using liquid scintillation spectrometry after preliminary sorption on cellulose fiber impregnated with copper(II) ferrocyanide was studied. This measurement procedure allows the ¹³⁷Cs detection efficiency to be increased to 50% and the sample volume to be decreased from 1000 (as in γ-ray spectrometry) to 50 L and less.     

Radionuclide Diagnostics of the Sorption Using the <Superscript>224</Superscript>Ra Subfamily and α-Ray Spectrometry

A method was suggested for radionuclide diagnostics of the sorption using the ²²⁴Ra subfamily and α-ray spectrometry. The method allows the diffusion in transport pores to be distinguished from the diffusion in a regular crystalline body. The possibilities of the method were illustrated by the example of a system consisting of a thin layer of manganese hydroxide deposited on three different kinds of support (cellulose triacetate, polyethylene, polyimide 66 in the form of flat discs 24 mm in diameter) and an aqueous ²²⁴Ra solution. A joint study of the kinetics of the Ra sorption and characteristics of α-ray spectra of samples of ²²⁴Ra sorbed onto thin-layer manganese hydroxide and of its daughter radionuclides (energy resolution and emanating ability of α-ray sources) allows the steps of external diffusion in a laminar liquid flow on the surface of sorbent granules, diffusion in transport pores, and diffusion in a regular crystalline body to be clearly distinguished in time.     

Estimating the effect of C<Stack><Subscript>2</Subscript><Superscript>−</Superscript></Stack> and C<Stack><Subscript>3</Subscript><Superscript>+</Superscript></Stack> radicals and neutral clusters on the fullerene formation

The mass spectrum of the products of arc discharge in helium between graphite electrodes has been studied for various values of the gas flow rate. As the gas flow rate increases, the intensity of C₆₀^±, C₇₀^±, C₈₄^± and C₉₀^± fullerene peaks increases and that of the C₂⁻ and C₃⁺ cluster radicals decreases, but the total decay in radicals amounts to only 21% of the total growth of fullerenes. From this it follows that a contribution to the formation of fullerenes from the neutral clusters (which are taken into account for the first time) significantly exceeds the contribution due to small radical species.     

Stability of the LaCl<Stack><Subscript>4</Subscript><Superscript>−</Superscript></Stack> and LuCl<Stack><Subscript>4</Subscript><Superscript>−</Superscript></Stack> Ions Studied by Mass Spectrometry

The enthalpy stability of the LaCl ₄ ^? and LuCl ₄ ^? ions is assessed using high-temperature mass spectrometry. The enthalpy of Cl^? detachment is determined to be Δ_rH⁰(298.15 K) = 332 ± 10 kJ/mol for LaCl ₄ ^? and 359 ± 10 kJ/mol for LuCl ₄ ^? .     

Use of a nanostructured material for separation of <Superscript>238</Superscript>U and <Superscript>237</Superscript>U produced by the photonuclear reaction <Superscript>238</Superscript>U(γ, <Emphasis Type="Italic">n</Emphasis>)<Superscript>237</Superscript>U

²³⁷U was produced by the reaction ²³⁸U(γ, n) on an electron accelerator, MT-25 microtron, at the Flerov Laboratory of Nuclear Reactions. For the separation of ²³⁷U and [²³⁸U, the recoil nuclei were collected by a nanostructured material, hydrated manganese dioxide (of the cryptomelane type), in the solid-solid system. From fission products, ²³⁷U was separated by ion exchange. The specific activity of the resulting ²³⁷U was 4.5 × 10⁹ Bq (mg ²³⁸U)^-1, with the content of radioactive impurities of ≤10^-6 Bq Bq^-1. The chemical yield of ²³⁷U was 80%.     

Formation-decomposition equilibrium of the NpO<Stack><Subscript>2</Subscript><Superscript>+</Superscript></Stack>·UO<Stack><Subscript>2</Subscript><Superscript>2+</Superscript></Stack> complex in chloride melts

The absorption spectra of the NpO ₂ ⁺ (5f ²) ion were examined in the region of the 3H ₅ ← ³ H ₄ magnetic dipole transition (1530–1760 nm) for series of melts with the UO ₂ ²⁺ concentration varied in the opposite directions: (1) NaCl-2CsCl eutectic melt with growing additions of the Cs₂UO₂Cl₄ complex salt and (2) Cs₂UO₂Cl₄ melt with growing additions of the NaCl-2CsCl mixture. Measurements of the integrated intensities of the bands belonging to the NpO ₂ ⁺ ·UO ₂ ²⁺ complex and unbound NpO ₂ ⁺ throughout the UO ₂ ²⁺ concentration range examined (up to 4.4 M in neat Cs₂UO₂Cl₄ melt) and processing of the data obtained in terms of the mass action law showed that the formation-decomposition reaction of the cation-cation complex can be described adequately only using the equation of reaction in the form NpO₂Cl ₄ ^3? + UO₂Cl ₄ ^2? ? {Cl₄ONpO?UO₂Cl₃}^4? = Cl^? (with the equilibrium constant of 1.3±0.1). Thus, the formation of the cationcation complex should be treated as replacement of chloride ion in the equatorial plane of uranyl(VI) by neptunyl(V), rather than as simple addition of UO ₂ ²⁺ to NpO ₂ ⁺ . The reverse reaction, decomposition of the cation-cation complex, consists essentially in replacement of neptunyl(V) by chloride ion.     

High-temperature tensile-hold crack-growth behavior of HASTELLOY<Superscript>®</Superscript> X alloy compared to HAYNES<Superscript>®</Superscript> 188 and HAYNES<Superscript>®</Superscript> 230<Superscript>®</Superscript> alloys

The creep–fatigue crack-growth tests of HASTELLOY^® X alloy were carried out at the temperatures of 649°C, 816°C, and 927°C in laboratory air. The experiments were conducted under a constant stress-intensity-factor-range (ΔK) control mode with a R-ratio of 0.05. In the constant ΔK tests, a ΔK of 27.5 MPa\(\sqrt{\mathrm{m}}\) and a triangular waveform with a frequency of 0.333 Hz were used. Various tensile hold times at the maximum load were imposed to study fatigue and creep–fatigue interactions. Crack lengths were measured by a direct current potential drop method. In this paper, effects of hold time and temperature on the crack-growth rates are discussed. Furthermore, the crack-growth rates of the HASTELLOY^® X alloy are compared to those of the HAYNES^® 188 and HAYNES^® 230^® superalloys.     

Comparison of an experimental bone cement with surgical Simplex<Superscript>®</Superscript> P,Spineplex<Superscript>®</Superscript> and Cortoss<Superscript>®</Superscript>

Conventional polymethylmethacrylate (PMMA) cements and more recently Bisphenol-a-glycidyl dimethacrylate (BIS-GMA) composite cements are employed in procedures such as vertebroplasty. Unfortunately, such materials have inherent drawbacks including, a high curing exotherm, the incorporation of toxic components in their formulations, and critically, exhibit a modulus mismatch between cement and bone. The literature suggests that aluminium free, zinc based glass polyalkenoate cements (Zn-GPC) may be suitable alternative materials for consideration in such applications as vertebroplasty. This paper, examines one formulation of Zn-GPC and compares its strengths, modulus, and biocompatibility with three commercially available bone cements, Spineplex, Simplex P and Cortoss. The setting times indicate that the current formulation of Zn-GPC sets in a time unsuitable for clinical deployment. However during setting, the peak exotherm was recorded to be 33 degrees C, the lowest of all cements examined, and well below the threshold level for tissue necrosis to occur. The data obtained from mechanical testing shows the Zn-GPC has strengths of 63 MPa in compression and 30 MPa in biaxial flexure. Importantly these strengths remain stable with maturation; similar long term stability was exhibited by both Spineplex and Simplex P. Conversely, the strengths of Cortoss were observed to rapidly diminish with time, a cause for clinical concern. In addition to strengths, the modulus of each material was determined. Only the Zn-GPC exhibited a modulus similar to vertebral trabecular bone, with all commercial materials exhibiting excessively high moduli. Such data indicates that the use of Zn-GPC may reduce adjacent fractures. The final investigation used the well established simulated body fluid (SBF) method to examine the ability of each material to bond with bone. The results indicate that the Zn-GPC is capable of producing a bone like apatite layer at its surface within 24 h which increased in coverage and density up to 7 days. Conversely, Spineplex, and Simplex P exhibit no apatite layer formation, while Cortoss exhibits only minimal formation of an apatite layer after 7 days incubation in SBF. This paper shows that Zn-GPC, with optimised setting times, are suitable candidate materials for further development as bone cements.     

Distribution of <Superscript>210</Superscript>Ро in lichen thalli

Distribution of ²¹⁰Po in thalli of soil and wood (epiphytic) lichens was studied. Four fractions containing the corresponding ²¹⁰Ро forms were obtained by sequential extraction: (1) intercellular, (2) extracellular, (3) intracellular, and (4) insoluble thallus residue. The ²¹⁰Ро uptake by lichens is mainly passive, as the total content of the radionuclide in fractions 1, 2, and 4 reaches 88–97%. From 3 to 12% of ²¹⁰Ро is taken up actively (fraction 3), and for soil lichens this parameter is approximately 2.75 times higher than for epiphytic lichens. Presumably, ²¹⁰Ро is supplied into soil and epiphytic lichens in the form of different chemical compounds and is therefore characterized by different bioavailability.     

Spectroscopic properties of Nd<Superscript>3+</Superscript>, Yb<Superscript>3+</Superscript>-doped and Nd<Superscript>3+</Superscript>–Yb<Superscript>3+</Superscript>-codoped high silica glass

The Nd³⁺, Yb³⁺-doped and Nd³⁺–Yb³⁺-codoped high silica glasses (HSGs) were fabricated by sintering porous glasses impregnated with Nd³⁺ and Yb³⁺ ions solutions. The Judd–Ofelt theory was used to study the spectroscopic properties of Nd³⁺-doped HSGs. Large parameter Ω₂ of Nd³⁺-doped HSGs suggests a lower centrosymmetric coordination environment around the Nd³⁺ in HSG. The spontaneous emission probability and emission cross-section (σ_em) of Yb³⁺-doped HSGs are obtained. A broad emission band from 950 to 1,100 nm was detected when the Nd³⁺–Yb³⁺-codoped HSG was excited by 808 nm LD. The energy transfer process from Nd³⁺ to Yb³⁺ in HSG was described in this paper.     

Role of Mg<Superscript>2+</Superscript>, Sr<Superscript>2+</Superscript>, and F<Superscript>–</Superscript> ions in octacalcium phosphate crystallization

We have synthesized octacalcium phosphate (OCP) in the presence of inorganic additives (magnesium, strontium, and fluoride ions) and studied the composition, morphology, thermal stability, and dynamic dissolution of the samples thus obtained. It has been shown that, in addition to OCP, magnesium and strontium ions favor the formation of brushite and hydroxyapatite (HA), whereas fluoride ions favor the formation of HA and fluorohydroxyapatite (FHA). We have proposed a process for the preparation of powder materials whose resorption kinetics in corrosive liquid media are corrected by adding dopants capable of activating the dissolution process.     

Characterization of <Superscript>4</Superscript>I<Subscript>9/2</Subscript> ↔ <Superscript>4</Superscript>F<Subscript>3/2</Subscript> optical transitions in trivalent Nd<Superscript>3+</Superscript> ions in GaLaS glass

The positions of Stark levels have been determined, using a step-by-step procedure, in the ⁴I_9/2 and ⁴F_3/2 manifolds of Nd³⁺ ions from absorption and photoluminescence measurements in the 12–293 K temperature range. This data has been used to calculate the emission cross-section for which the maximum value turns out to be ～2.3 × 10^?20 cm². The radiative recombination time, calculated using Judd–Ofelt analysis, of the ⁴F_3/2 manifold is in close vicinity to the experimentally determined times that were measured by the conventional decay of PL after interruption of excitation and by QFRS. Moreover, the peak time defined by QFRS is independent of temperature. Therefore, the dominant relaxation mechanism from the ⁴F_3/2 excited manifold of Nd³⁺ ions in GaLaS glass is believed to be by radiative emission.     

Mechanochemical synthesis of γ-LiAlO<Subscript>2</Subscript> studied by <Superscript>6</Superscript>Li and <Superscript>27</Superscript>Al NMR and synchrotron X-Ray diffraction

The structural transformations accompanying the mechanochemical synthesis of fine-particle γ-LiAlO₂ have been studied by ⁶Li and ²⁷Al NMR and in situ X-ray diffraction. Mechanical activation of a mixture of aluminum hydroxide and lithium carbonate in an AGO-2 planetary mill results not only in size reduction, intermixing, and partial amorphization of the starting materials but also in the mechanochemical synthesis of a carbonate form of aluminum lithium hydroxide. Subsequent heat treatment of the mechanically activated mixture leads to the release of water and carbon dioxide molecules and the formation of an X-ray amorphous phase containing aluminum in octahedral and tetrahedral oxygen coordination. The X-ray amorphous material converts to gamma lithium aluminate through an intermediate phase.     

Effects of pH and concentration on ability of Cl<Superscript>−</Superscript> and NO<Stack><Subscript>3</Subscript><Superscript>−</Superscript></Stack> to intercalate into a hydrotalcite-like compound during its synthesis

In this study, we confirmed that the characteristics of anion intercalation into the interlayer of a hydrotalcite-like compound (HT) during synthesis are similar to those of the anion-exchange reaction of HTs as well as the reconstruction reaction of HTs from Mg-Al oxide. We demonstrated that (i) Cl⁻, which has a higher charge density than NO₃⁻, more easily reacted with Mg and Al species to form HT structure, resulting in greater intercalation of Cl⁻ into the HT interlayer; and (ii) for HTs with lower Mg: Al molar ratios, OH⁻, which has a higher charge density than Cl⁻ and NO₃⁻, was more likely to interact with Mg and Al species to form HT structure, blocking the intercalation of Cl⁻ and NO₃⁻. Furthermore, we showed that high concentrations of Cl⁻ and NO₃⁻ in solution regulated their intercalation into the HT interlayer. The high activity of Cl⁻ and NO₃⁻ in solution would facilitate the anions’ reactions with Mg and Al species to form HTs, resulting in a high degree of anion intercalation into the interlayer of HTs.     

<Superscript>172</Superscript>Hf → <Superscript>172</Superscript>Lu Radionuclide Generator Based on a Reverse-Tandem Separation Scheme

The distribution coefficients of Hf(IV) and Lu(III) between Dowex 50W×8 cation exchanger or Dowex 1×8 anion exchanger and mixed HCl–H₂C₂O₄ solutions and between Dowex 50W×8 cation exchanger or Dowex 1×8 anion exchanger and citric acid solutions were determined. A number of modifications of the ¹⁷²Hf → ¹⁷²Lu generator, based on reverse separation schemes, were examined. Systems consisting of an anion-exchange resin and a solution of appropriate organic acid were taken as a chemical basis of the generator. Irreversible sorption of ¹⁷²Lu in generator columns was studied. The optimum operation mode of the ¹⁷²Hf → ¹⁷²Lu generator based on the reverse-tandem scheme with periodic transfer of the parent radionuclide into the liquid phase was determined.     

Piezo-spectroscopic behavior of the emission bands of α-alumina in the 13900–14250 cm<Superscript>− 1</Superscript> spectral range

The emission spectrum of -alumina in the spectral range between 13900 and 14250 cm^–1 is characterized by several bands which are much weaker than the two intense and sharp R1 and R2 bands appearing at 14400 and 14430 cm^–1, respectively; these latter are known as Ruby lines and they are the emission bands used in the Ruby laser. Furthermore these bands shift in frequency with stress (Piezo-Spectroscopic effect). In this paper, for the first time, the stress-dependent peak frequency of the weaker bands in the 13900–14250 cm^–1 range is calibrated, and the results are presented as Piezo-Spectroscopic coefficients. The calibration is performed by reporting the frequency shift of each investigated band as function of varying stresses. The stresses, residual in nature, are obtained by fabricating composite materials where -alumina is mixed in various amounts with (i) Ceria-Stabilized Tetragonal Zirconia Polycrystals (Ce-TZP) and (ii) silicon carbide, SiC. The composite materials are prepared at high temperature (1500°–1800°C); due to the difference in thermal expansion, upon cooling to room temperature -alumina develops compressive and tensile stresses, when mixed with Ce-TZP and SiC, respectively. The stress values necessary for the calibration are obtained from the frequency shift of the R2 band, using its well-established Piezo-Spectroscopic coefficient (7.6 cm^–1/GPa). Then the newly obtained Piezo-Spectroscopic coefficients of the bands in the 13900–14250 cm^–1 range are tested to retrieve the stresses in two sets of composites; finally the stress values are compared with those obtained in the same samples from the frequency shift of the R2 band. The comparison shows a very good agreement, thus providing evidence that the bands in the 13900–14250 cm^–1 range can be used to monitor stresses in -alumina-based materials.     

Influence of pH of Nitric Acid Solution on the Kinetics of the <Superscript>99</Superscript>Мо Sorption onto Titanium Hydroxide

The kinetics of the ⁹⁹Мо sorption onto T-5 sorbent at different pH values of the nitric acid solution was studied. The previously suggested limiting steps of the ⁹⁹Мо sorption onto Т-5 sorbent were confirmed. The effective rate constant of the molybdenum sorption onto titanium hydroxide (fast step) as a function of pH passes through a maximum at pH from 4.5 to 5.5, which does not correspond to the maximum of the pH dependence of the distribution coefficient but correlates with the maximal content of one of the sorbable species, НМоО₄^–, in the solution. Thus, the rate of Mo sorption onto titanium hydroxide as a function of pH passes through a maximum at a minimal negative charge of the sorbate near pH of the isoelectric point of the sorbent. The kinetic studies confirm the scheme of the sorption of molybdenum hydroxo complexes onto titanium hydroxide, suggested previously on the basis of the logk_d–рН and log ε–log[m] sorption isotherms. According to this scheme, simultaneous redistribution and sorption of sorbable molybdenum species, МоО₂ОН⁺, Н₂МоО₄, and НМоО₄^–, are possible.     

Synthesis of Yb<Superscript>3+</Superscript>, Ho<Superscript>3+</Superscript> and Tm<Superscript>3+</Superscript> co-doped β-NaYF<Subscript>4</Subscript> nanoparticles by sol–gel method and the multi-color upconversion luminescence properties

Well-crystalline β-NaYF₄:Yb³⁺, Ho³⁺, Tm³⁺ nanoparticles were synthesized by sol–gel method using isopropyl alcohol [(CH₃)₂CHOH] as a complexing agent. The samples were characterized by X-ray diffraction, scanning electron microscopic analysis and fluorescence spectrum analysis methods. Under the excitation of 980 nm laser diode (LD), the samples displayed bright upconversion luminescence (UCL), which was generated from the energy level transition of Ho³⁺ and Tm³⁺ ions. With the increase of Tm³⁺, Ho³⁺ and Yb³⁺-doping concentration, the UCL intensity of blue, green and red light emission of the samples varied. Calculation of the CIE color coordinate of the β-NaYF₄:Yb³⁺, Ho³⁺, Tm³⁺ nanoparticles revealed that with the adjustment of Tm³⁺, Ho³⁺ and Yb³⁺ doping concentration and the excitation power of 980 nm LD, the multi-color UCL can be realized. Approximately single red light output with the CIE color coordinate of x?=?0.545, y?=?0.306 and white light output with the CIE color coordinate of x?=?0.325, y?=?0.320 can be obtained in the synthesized β-NaYF₄: Yb³⁺, Ho³⁺, Tm³⁺ nanoparticles.     

Synthesis,electronic state,and particle size stabilization of nanoparticulate [Co(OH)<Subscript>2</Subscript>(H<Subscript>3</Subscript>O)<Stack><Subscript>δ</Subscript><Superscript>+</Superscript></Stack>]<Superscript>δ+</Superscript>

We have synthesized nanoparticulate cobalt(II) hydroxide containing Co²⁺ in tetrahedral oxygen coordination (Co _Td ²⁺ ), atypical of such systems: nano- [Co(OH)₂(H₃O) _δ ⁺ ]^δ+. The (Co _Td ²⁺ ) coordination in the hydroxide is inferred from its electronic diffuse reflectance spectrum, which shows a multiplet of strong absorption bands at 14500, 15000, and 16000 cm^?1 (⁴ A ₂(F)-⁴ T ₁(P) transition). Nanoparticulate cobalt(II) hydroxide forms in a weakly acidic medium under essentially nonequilibrium conditions due to supersaturation (by three to four orders of magnitude) with the starting reagents (CoCl₂ and LiOH) at the instant of the formation of the poorly soluble phase Co(OH)₂. Presumably, colloidal particles of nanoparticulate cobalt(II) hydroxide in a weakly acidic aqueous medium have a positive surface charge, compensated by a counter-ion (Cl^?) layer: nano-[Co(OH)₂(H₃O) _δ ⁺ ]^δ+ · δCl^?. The XRD patterns of pastes (gels) containing this hydroxide show three broad-ened lines with d = 5.31 (2θ = 16.7°), 2.77 (2θ = 32.3°), and 2.32 Å (2θ = 38.8°). According to small-angle X-ray scattering data, nano-[Co(OH)₂(H₃O) _δ ⁺ ]^δ+ has a narrow particle size distribution (1.0–2.0 nm). Synthesis and storage conditions are identified which ensure stabilization of the electronic state and particle size of nano-[Co(OH)₂(H₃O) _δ ⁺ ]^δ+ for a long time.     

New state primary special standard of unit of electrical voltage (volt) in the frequency range 3·10<Superscript>7</Superscript>–2·10<Superscript>9</Superscript> Hz

The design structure is considered and the basic metrological characteristics of a new state primary special standard is presented.