Stress Corrosion Cracking Behavior of Multipass TIG-Welded AA2219 Aluminum Alloy in 3.5?wt?pct NaCl Solution

The stress corrosion cracking (SCC) behavior of the AA2219 aluminum alloy in the single-pass (SP) and multipass (MP) welded conditions was examined and compared with that of the base metal (BM) in 3.5?wt?pct NaCl solution using a slow-strain-rate technique (SSRT). The reduction in ductility was used as a parameter to evaluate the SCC susceptibility of both the BM and welded joints. The results showed that the ductility ratio (?? _NaCl/(?? _air) was 0.97 and 0.96, respectively, for the BM and MP welded joint, and the same was marginally reduced to 0.9 for the SP welded joint. The fractographic examination of the failed samples revealed a typical ductile cracking morphology for all the base and welded joints, indicating the good environmental cracking resistance of this alloy under all welded conditions. To understand the decrease in the ductility of the SP welded joint, preexposure SSRT followed by microstructural observations were made, which showed that the decrease in ductility ratio of the SP welded joint was caused by the electrochemical pitting that assisted the nucleation of cracks in the form of corrosion induced mechanical cracking rather than true SCC failure of the alloy. The microstructural examination and polarization tests demonstrated a clear grain boundary (GB) sensitization of the PMZ, resulting in severe galvanic corrosion of the SP weld joint, which initiated the necessary conditions for the localized corrosion and cracking along the PMZ. The absence of PMZ and a refined fusion zone (FZ) structure because of the lesser heat input and postweld heating effect improved the galvanic corrosion resistance of the MP welded joint greatly, and thus, failure occurred along the FZ.     

Electrochemical Corrosion and Impedance Studies of Porous Ti–xNb–Ag Alloy in Physiological Solution

Porous titanium (Ti) and its alloys are promising materials for orthopedic applications due to their low elastic modulus, high strength, excellent corrosion resistance, and biocompatibility. In this study, the porous Ti–xNb–5Ag (x = 25, 30 and 35 wt%) alloys were synthesized using the powder metallurgy approach. The effects of Nb content on the porosity, mechanical properties, and electrochemical corrosion behavior of the alloys were investigated. XRD analysis revealed that the porous alloys mainly consist of α-Ti, β-Ti, intermetallic compound (Ti₄Nb), and oxides of TiO₂ and NbO phases. Porous alloys possess the porosity ranging from 57 to 65%, due to the addition of NH₄HCO₃ (45 wt%). Increase in Nb content lead to a reduction in the elastic modulus and compression strengths of the sintered porous Ti–xNb–5Ag alloys. All three developed porous Ti–xNb–5Ag alloys show the optimum combination of elastic modulus and compression strength, which is suitable for orthopedic applications. These porous alloys exhibit excellent electrochemical corrosion resistance in the simulated body fluids, and the samples having low porosity exhibit higher corrosion resistance than high-porosity samples.

     

Effect of Electrodeposition Current and Pulse Parameter on Surface Mechanical and Electrochemical Behavior of Ni–W Alloy Coatings

Metallurgical and Materials Transactions A - Ni–W alloy coatings have various applications because they are capable of replacing hard chromium coatings due to their corrosion, oxidation,...     

Corrosion Behavior of Alloy 625 in PbSO4-Pb3O4-PbCl2-ZnO-10?Wt?Pct CdO Molten Salt Medium

Corrosion behavior and degradation mechanisms of alloy 625 under a 47.288 PbSO₄-12.776 Pb₃O₄-6.844PbCl₂-23.108ZnO-10CdO (wt pct) molten salt mixture under air atmosphere were studied at 873?K, 973?K, and 1073?K (600?°C, 700?°C, and 800?°C). Electrochemical impedance spectroscopy (EIS), open circuit potential (OCP) measurements, and potentiodynamic polarization techniques were used to evaluate the degradation mechanisms and characterize the corrosion behavior of the alloy. Morphology, chemical composition, and phase structure of the corrosion products and surface layers of the corroded specimens were studied by scanning electron microscopy/energy-dispersive X-ray (SEM/EDX) and X-ray map analyses. Results confirmed that during the exposure of alloy 625 to the molten salt, chromium was mainly dissolved through an active oxidation process as CrO₃, Cr₂O₃, and CrNbO₄, while nickel dissolved only as NiO in the system. Formation of a porous and nonprotective oxide layer with low resistance is responsible for the weak protective properties of the barrier layer at high temperatures of 973?K and 1073?K (700?°C and 800?°C). There were two kinds of attack for INCONEL 625, including general surface corrosion and pitting. Pitting corrosion occurred due to the breakdown of the initial oxide layer by molten salt dissolution of the oxide or oxide cracking.     

Effects of Route on Microstructural Evolution and Mechanical Properties of Cu-8 Wt Pct Ag Alloy Processed by Equal Channel Angular Pressing

Equal channel angular pressing (ECAP) is applied to investigate the microstructural evolution and mechanical properties of Cu-8 wt pct Ag alloy subjected to one to four passes via four different routes (A, B_A, B_C, and C). It is demonstrated that better mechanical properties, a higher fraction of high-angle boundaries, and a smaller grain size can be obtained most rapidly with route A, whereas the specimen processed by route B_C contains relatively inhomogeneous microstructure and has poor mechanical properties. The ultimate tensile stress (UTS) of the Cu-Ag alloy processed by route B_C saturates after four passes; in contrast, the UTS of the Cu-Ag alloy processed by route A increases continuously in relation to the number of ECAP passes. Based on the experimental results, the strengthening mechanisms of the Cu-8 wt pct Ag alloy processed by different routes as well as the efficiency of different routes in refining the binary alloy are discussed.     

Electrolytic Deposition and Diffusion of Lithium onto Magnesium-9 Wt Pct Yttrium Bulk Alloy in Low-Temperature Molten Salt of Lithium Chloride and Potassium Chloride

The electrolytic deposition and diffusion of lithium onto bulk magnesium-9 wt pct yttrium alloy cathode in molten salt of 47 wt pct lithium chloride and 53 wt pct potassium chloride at 693 K were investigated. Results show that magnesium-yttrium-lithium ternary alloys are formed on the surface of the cathodes, and a penetration depth of 642 μm is acquired after 2 hours of electrolysis at the cathodic current density of 0.06 A·cm⁻². The diffusion of lithium results in a great amount of precipitates in the lithium containing layer. These precipitates are the compound of Mg₄₁Y₅, which arrange along the grain boundaries and hinder the diffusion of lithium, and solid solution of yttrium in magnesium. The grain boundaries and the twins of the magnesium-9 wt pct yttrium substrate also have negative effects on the diffusion of lithium.     

Development of Silica Glass Coatings on 316L SS and Evaluation of its Corrosion Resistance Behavior in Ringer’s Solution

Sol-gel derived silica glasses have many promising features, including low-temperature preparation as well as chemical and physical stability. Two silica glasses with Si₁₀₀ and Si₈₀ composition were prepared to understand the factors contributing to the rate of bioactivity. The effects of pH, solution aging temperature, and molar ratio of H₂O/tetraethyl orthosilicate (TEOS) were studied, and the obtained powder sample was characterized by Fourier transform infrared spectroscopy, X-ray diffraction studies, and scanning electron microscopy. The synthesized silica glasses were deposited on 316L SS by the spin coating method at the optimized speed of 2000?revolutions per minute. The corrosion resistance behavior of the coatings was determined by (1) open-circuit potential vs time of exposure, (2) electrochemical impedance spectroscopy, and (3) cyclic polarization in Ringer??s solution. A higher breakdown potential (E _b) and repassivation potential (E _p) value with lower current density was obtained from cyclic polarization. Similar results were observed from impedance analysis with higher charge transfer resistance (R _ct) and lower double layer capacitance (C _dl) indicating the corrosion resistance behavior of the coatings compared with the uncoated 316L stainless steel. From the results, it was observed that both Si₁₀₀ and Si₈₀ glass coatings had a positive effect on the corrosion resistance behavior. An adhesive strength of 46?MPa and 45?MPa was obtained for the Si₁₀₀ and Si₈₀ coatings, respectively. An accelerated leach out study was carried out by impressing the potential at their breakdown potential to determine the effect of glass coating for long-term contact between the implant and a normal biological medium.     

Influence of Filler Wire Diameter on Mechanical and Corrosion Properties of AA5083-H111 Al–Mg Alloy Sheets Welded Using an AC Square Wave GTAW Process

In this work, the influence of filler wire diameter on AA5083-H111 weldments was studied. For that, square butt joints were made using an AC square wave gas tungsten arc welding process with the addition of filler wires of diameter 1.2 and 2.4 mm separately. The experimental results revealed that changing the filler wire diameter influenced the bead geometry and a complete penetration was achieved in both welds. The weldment processed with smaller diameter filler wire consisted of a wider heat affected zone with recrystallized grains and a fusion zone with coarser grain structure, thus reducing the mechanical properties and corrosion resistance. However, the use of larger diameter filler wire assisted in faster torch speed, resulting in lower heat input and thus finer equiaxed grains were produced in fusion zone. Also, finer grains along with the dispersion of finer Al₆(Fe,Mn) particles supported in obtaining the superior tensile and corrosion properties.     

Effect of Strain Rate on the Microstructure and Mechanical Properties of AA2B06-O Aluminum Alloy of the Al–Cu–Mg System

Russian Journal of Non-Ferrous Metals - The mechanical properties in the tension and microstructure of aviation aluminum alloy AA2B06-O (the Al–Cu–Mg system) at low (10–3–1...     

Evolution of Texture,Strain, and Grain Boundary Constitution in Copper–Chromium Coatings and its Effect on Coating Corrosion Behavior

Metallurgical and Materials Transactions A - Microstructural alterations in electrodeposited Cu–Cr coatings (1.5, 3.6, and 6.5 wt pct Cr) and their impact on the coating corrosion behavior...     

Refining Effect of a New Al3Ti1B1RE Master Alloy on Al Sheets Used for Can Manufacture and Behavior of Rare Earths in Master Alloy

The refining effect of Al3Ti1B1RE master alloy on Al sheets used for pressure can manufacture and the behav-ior of mixed rare earths (RE) in master alloy were investigated with XRD, OM, SEM and EDAX. It is found that the re-fining effect of the refiner on the material has superiority over foreign or domestic Al5Ti1B refiner, and the refiner still re-tains its refining ability for 6 h after adding it to molten Al, thus improving the strength and plasticity of the material re-markably. The excellent refining effect and stability of AlTiBRE refiner result from that RE can lower the surface energy of molten Al and improve the wetting characteristics of molten Al on refinement nuclei such as TiAl3, TiB2, etc., thus giving full play to the effect of heterogeneous nucleation and impeding the congregating tendency of TiB2 phase in molten Al. At the same time, RE gathering in front of solid/liquid interface are also easy to cause composition supercooling in molten Al, thus impeding the growth of α-Al grains and promoting α-Al nucleation on refinement nuclei. In addition, RE also play certain role in purification and grain refinement, or modification, especially their effect of purification can improve the metallurgical quality of AlTiBRE master alloy.     

The Effect of Small Additions of Fe and Heavy Deformation on the Precipitation in an Al–1.1Mg–0.5Cu–0.3Si At. Pct Alloy

Metallurgical and Materials Transactions A - The effect of 0.03 and 0.08 at. pct Fe additions on the formation of secondary phases in an Al–1.1Mg–0.5Cu–0.3Si at. pct alloy was...