Mechanical Properties and Thermal Shock Resistance of Al2O3-TiC-Co Composites

Ductile cobalt was introduced into Al₂O₃-TiC (AT) composites by using a chemical deposition method to improve toughness and resistance to thermal shock. The mixture of Co-coated Al₂O₃ and TiC powders was hot-pressed into an Al₂O₃-TiC-Co (ATC) composite. The flexure strength and fracture toughness of the ATC composites have been improved considerably, compared with AT and Al₂O₃. The fracture surface of ATC shows a large proportion of transgranular cracks with some intergranular type, unlike the intergranular fracture modes of AT and Al₂O₃. The thermal shock properties of the composites were evaluated by water quenching technique and compared with the traditional AT and Al₂O₃. The composites containing only 3.96 vol.% cobalt exhibited higher critical temperature difference and retained flexure strength. The SEM examination of the fracture surfaces of the ATC composites after single thermal cycle showed that voids increased in number and size, and most isolated voids coalesced with increasing temperature difference, which caused the density and strength to decrease. The ATC composite is less sensitive to repeated thermal shock than the AT composite.     

Sr对合成Al3Ti/ADC12复合材料微观组织与力学性能的影响

本文研究了不同含量的改性剂Sr对原位合成Al₃Ti/ADC12复合材料微观组织及力学性能的影响。通过光学显微镜以及扫描电镜观察复合材料的微观以及断口组织。实验结果表明：Sr的加入能有效减小α-Al以及Al₃Ti颗粒尺寸以及优化材料形态。Sr的最优加入量为0.25 wt%。在该加入量条件下,共晶硅由针状或短棒状变为颗粒状,α-A1粗枝晶得到较好的细化。实验结果也显示：Sr的加入有效提升了复合材料的机械性能。当加入0.25 wt% Sr时,抗拉强度以及延伸率相较于基体材料增加了36.9% 和 58%。断口形貌表明,在最优加入量条件下所制备的复合材料断口几乎看不到解理面和脆性平坦区,韧窝数量增多,形貌尺寸变得更小且深,同时分布也较为均匀。断口形貌的变化符合材料力学性能变化。     

ZrB2增韧Al2O3陶瓷制备工艺及其对复相陶瓷力学性能影响

Al₂O₃陶瓷因具有很高的强度和耐蚀性受到广泛关注。但由于相对较差的韧性限制了其广泛应用。Al₂O₃陶瓷增韧的方式很多,本文采用微米ZrB₂来增韧氧化铝陶瓷,探讨复相陶瓷烧结工艺,并研究工艺参数对复相陶瓷力学性能及韧性的影响。结果表明：采用单因素法得到两种陶瓷最佳工艺参数分别是纯α-Al₂O₃陶瓷烧结温度为1500℃,成型压力为450MPa,保温时间为8h,球料比为1/2,保压时间为10min;ZrB₂(wt,20%)+α-Al₂O₃ (wt,80%)复相陶瓷烧结温度为1450℃,成型压力为450MPa,保温时间为8h,球料比为1/2,保压时间为10min。其中成型压力、烧结温度和保温时间对复相陶瓷硬度及致密度影响最大。ZrB₂的加入,在降低陶瓷烧结温度的同时,可以将纯α-Al₂O₃陶瓷的断裂韧性由5.2±0.3MPa.m^_1/2提高到6.7±0.2MPa.m^_1/2。     

Mechanical and tribological performance of Al2O3-TiO2 coatings elaborated by flame and plasma spraying

Mechanical properties and wear rates of Al₂O₃-13 wt.% TiO₂ (AT-13) and Al₂O₃-43 wt.% TiO₂ (AT-43) coatings obtained by flame and atmospheric plasma spraying were studied. The feed stock was either ceramic cords or powders. Results show that the wear resistance of AT-13 coatings is higher than that of AT-43 and it seems that the effect of hardness on wear resistance is more important than that of toughness. Additionally, it was established that, according to conditions used to elaborate coatings and the sliding tribological test chosen, spray processes do not seem to have an important effect on the wear resistance of these coatings.     

Densification and mechanical properties of fine-grained Al2O3-ZrO2 composites consolidated by spark plasma sintering

Alumina matrix composites containing 5 and 10 wt% of ZrO₂ were sintered under 100 MPa pressure by spark plasma sintering process. Alumina powder with an average particle size of 600 nm and yttria-stabilized zirconia with 16 at% of Y₂O₃ and with a particle size of 40 nm were used as starting materials. The influence of ZrO₂ content and sintering temperature on microstructures and mechanical properties of the composites were investigated. All samples could be fully densified at a temperature lower than 1400 °C. The microstructure analysis indicated that the alumina grains had no significant growth (alumina size controlled in submicron level 0.66-0.79 μm), indicating that the zirconia particles provided a hindering effect on the grain growth of alumina. Vickers hardness and fracture toughness of composites increased with increasing ZrO₂ content, and the samples containing 10 wt% of ZrO₂ had the highest Vickers hardness of 18 GPa (5 kg load) and fracture toughness of 5.1 MPa m^1/2.     

La2O3含量对Al2O3/Cu基复合材料组织与性能的影响

以La₂O₃粉、Al粉、CuO粉为反应物原料、纯铜为基体,采用原位合成技术和近熔点铸造法制备颗粒增强Cu基复合材料,研究La₂O₃对Al-CuO体系制备的Cu基复合材料组织及性能的影响。结果表明：添加La₂O₃可获得纳米Al₂O₃颗粒,且弥散分布于Cu基体中,制备的材料组织更加细小、均匀,其材料的电导率及摩擦磨损性能明显提高。当添加0.6%wtLa₂O₃,复合材料的电导率达到90.2%IACS,磨损量达到最小,相比未添加La₂O₃,其导电率提高10.1%,磨损量减小36.6%。     

Strengthening and toughening forming of Al/Al2O3 composite in pseudo-semi-solid state

A new technology—thixo-die-forging of the composite in pseudo-semi-solid state was proposed based on the powder metallurgy technology combing with semi-solid metal process, and the cup shells with Al/Al₂O₃  composite was prepared successfully. The metallographic analysis and performance test show that the microstructure of parts is dense and mechanical properties are excellent with the volume fraction of Al is 37 %. The bend strength and fracture toughness of the composite are about 570-690 MPa and 8.5-16.8 MPa m^1/2, respectively. Comparing with reaction in situ and high temperature oxidation technologies the bending strength and fracture toughness are improved greatly. At the same time, it shows that the technology parameters have great influences on the properties. So it is feasible to prepare metal/ceramics composites by the proposed technology.     

BN/Al2O3 复合粉末及其聚合物基复合材料的制备与导热性能

采用固-液相共混法制备了多种BN/Al₂O₃复合粉末,通过冻融法和表面修饰法对BN进行了改性处理,改变表面修饰剂类型和摩尔比得到了前驱体和烧结态BN/Al₂O₃复合粉末,并利用机械混合法制备了聚合物基BN/Al₂O₃复合材料,并测试分析了其导热性能。结果表明,经冻融处理的BN分散性和界面相容性明显优于未经冻融处理的BN。多巴胺对BN的改性效果优于聚乙二醇。采用多巴胺作为表面修饰剂且BN与Al(NO₃)₃的摩尔比为1:1时,能够得到纳米Al₂O₃均匀包覆的微米BN粉末,即BN/Al₂O₃微纳复合粉末,其聚合物基复合材料的导热系数可达0.62 W·m^-1·K^-1,是纯聚合物导热系数的3倍,是采用纯微米BN粉末制备的聚合物基复合材料导热系数的1.5倍。在BN表面附着的Al₂O₃可以形成层状热传导通道,能够有效提高聚合物基BN/Al₂O₃复合材料的热导率。     

国外多孔基体氧化铝/氧化铝复合材料工程应用进展

氧化铝/氧化铝复合材料(Al2O3/Al2O3)是20世纪90年代兴起的一类连续陶瓷纤维增强陶瓷基复合材料,已经发展为与SiC/SiC、C/SiC等非氧化物陶瓷基复合材料并列的一类陶瓷基复合材料。与非氧化物陶瓷基复合材料相比,Al2O3/Al2O3具有长时抗氧化、高温耐腐蚀、低成本等独特优势,已经在航空发动机、地面燃气轮机等军民两用热结构材料领域展现出广阔的应用前景。本文从材料应用的角度出发,系统分析阐述了目前在Al2O3/Al2O3占主导地位的多孔基体Al2O3/Al2O3(P-Al2O3/Al2O3)的增韧机制、成型工艺和性能特点,重点归纳了国外近年来P-Al2O3/Al2O3的工程化应用进展及前景,最后指出了P-Al2O3/Al2O3存在的局限性并展望了未来发展方向,旨在为国内Al2O3/Al2O3体系发展提供借鉴和参考。     

Mechanochemical synthesis of Al2O3-TiB2 nanocomposite powder from Al-TiO2-H3BO3 mixture

Alumina-titanium diboride nanocomposite (Al₂O₃-TiB₂) was produced using mixtures of titanium dioxide, acid boric and pure aluminum as raw materials via mechanochemical process. The phase transformation and structural characterization during mechanochemical process were utilized by X-ray diffractometry (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), and thermogravimetric analyses (TG-DTA) techniques. A thermodynamic appraisal showed that the reaction between TiO₂, B₂O₃ and Al is highly exothermic and should be self-sustaining. XRD analyses exhibited that the Al₂O₃-TiB₂ nanocomposite was formed after 1.5 h milling time. The results indicate that increasing milling time up to 40 h had no significant effect other than refining the crystallite size.     

Al_2O_3/MoS_2复合涂层的制备及摩擦磨损性能

以大气等离子喷涂工艺制备的Al_2O_3陶瓷涂层为模板,利用陶瓷涂层中存在的孔隙和微裂纹,采用水热反应在其内部原位合成具有润滑特性的MoS_2,制备出Al_2O_3/MoS_2的复合涂层。结果表明,通过水热反应在陶瓷涂层原有的微观缺陷中成功合成了MoS_2,合成的MoS_2固体粉末呈类球形状,并且这球状的粉末是由纳米片层状的MoS_2搭建组成的。摩擦试验结果表明,与纯Al_2O_3涂层相比,复合涂层中由于MoS_2润滑膜的形成,其摩擦因数和磨损率都显著降低,且载荷越大,复合涂层的摩擦性能越好。     

水热法制备C3N4/CuGaO2 复合物及其气敏性能

采用简单水热法合成了一系列C₃N₄/CuGaO₂复合材料。采用XRD、SEM、TEM和XPS对制备的样品进行了表征。研究了一系列C₃N₄/CuGaO₂复合材料的气敏性能。结果表明,基于C₃N₄/CuGaO₂-0.3复合材料（C₃N₄与CuGaO₂的摩尔比为0.3:1）的气体传感器对甲苯的传感性能优于CuGaO₂传感器。相比较于CuGaO₂传感器的工作温度（140 ℃）,C₃N₄/CuGaO₂-0.3复合材料传感器的最佳工作温度仅为25 ℃,对100 μL/L甲苯气体的响应达到28,检出限低至0.01 μL/L。对100 μL/L甲苯气体的响应时间和恢复时间分别为114.2和27.4 s。此外,用于检测甲苯的C₃N₄/CuGaO₂-0.3复合材料传感器还具有优异的长期稳定性、良好的重复性和优异的抗湿性能。     

CVD deposition and characterization of coloured Al2O3/ZrO2 multilayers

Coloured Al₂O₃/ZrO₂ multilayers have been deposited onto WC-Co based inserts by a CVD process. Through physical as well as optical analysis of such multilayers, colour is believed to originate from interference. The coatings are obtained with good process reproducibility. It was found that the ZrO₂ process used in the multilayer, with ZrCl₄ as the only metal chloride precursor, results in a mixture of tetragonal and monoclinic ZrO₂ phases. However by adding a relatively small amount of AlCl₃ during such a process results in ZrO₂ layers being composed of predominantly tetragonal ZrO₂ phase. Corresponding multilayers seem to have a more fine grained and smoother morphology whereas multilayers containing monoclinic ZrO₂ phase seem to be less perfect with existence of larger grains of ZrO₂ which are believed to scatter light and alter the reflectance of such a multilayer. In addition to this, such multilayers were found to be free of or with greatly reduced amount of thermal cracks, normally present in pure CVD grown Al₂O₃ layers.It is believed that, in the studied Al₂O₃/ZrO₂ multilayers, the observed tetragonal ZrO₂ phase is the result of a size effect, where small enough ZrO₂ crystallites energetically favor the tetragonal phase. However as the ZrO₂ crystallite size distribution is shifted to larger sizes it is believed that a mixture of crystallites with both stable and metastable tetragonal phases as well as a stable monoclinic phase is obtained. The proposed metastable tetragonal ZrO₂ phase may in fact explain the absence of thermal cracks in such multilayers through a transformation toughening mechanism, well known in ZrO₂ based ceramics.     

Cu-Al合金薄板内氧化析出相Al_2O_3晶型及分布

Al含量为0.50%(质量分数)的Cu-Al合金薄板在900℃下内氧化25 h制备Cu-Al_2O_3薄板复合材料,并用富集萃取法提取Cu-Al_2O_3复合材料中的Al_2O_3相。利用TEM分析了Cu-Al_2O_3薄板中的Al_2O_3相的种类、分布、与Cu基体的界面关系,用X射线衍射和TEM研究了萃取粉末的组成。结果表明,Cu-Al薄板内氧化法所得的Cu-Al_2O_3复合材料的析出相主要为γ-Al_2O_3,有少量的α-Al_2O_3和θ-Al_2O_3相存在。析出相Al_2O_3颗粒弥散分布在Cu基体上,且析出相γ-Al_2O_3与Cu基体完全共格;Cu-Al_2O_3薄板复合材料从表层至深约0.5 mm处,Al_2O_3颗粒粒径逐渐减小,从14 nm减小到5 nm,颗粒间距逐渐增大,从10 nm增加到15 nm。     

In-situ TiB2 and Al2O3 formation by DC plasma spraying

In-situ plasma spraying (IPS) is a promising process to fabricate composite coatings with in-situ formed thermodynamically stable phases. In the present study, mechanically alloyed Al-12Si, B₂O₃ and TiO₂ powder was deposited onto an aluminum substrate using atmospheric plasma spraying (APS). It has been observed that, during the coating process, TiB₂ and Al₂O₃ are in-situ formed through the reaction between starting powders and finely dispersed in hypereutectic Al-Si matrix alloy. Also, obtained results demonstrate that in-situ reaction intensity strongly depends on spray conditions.     

Effect of Al2O3 reinforcement and precipitates on corrosion behaviour of 2618 and 6061 aluminium MMCs

ABSTRACT

The corrosion resistance features of two different Metal Matrix Composites based on 6061 and 2618 aluminium alloys reinforced by 20% Al₂O₃ particles by stir casting process, were studied in 3.5% NaCl and compared. The composites and their respective base alloys were characterised in terms of microstructure by optical and scanning electron microscopy and in terms of corrosion resistance by polarisation curves and electrochemical impedance. Results show how the presence of Al₂O₃ has different effects depending on matrix composition. In 6061 MMC, Al₂O₃ promotes the formation of Mg₂Si which has a cathodic behaviour altering the pitting susceptibility of the composite. In 2618 MMC, the high content of Cu induces a strong uniform attack. The subsequent increase in the Open Circuit Potential caused a pitting attack.     

Microstructure and mechanical properties of Al2O3-Cr2O3 composite coatings produced by atmospheric plasma spraying

Al₂O₃, Al₂O₃-Cr₂O₃ and Cr₂O₃ coatings were deposited by atmospheric plasma spraying. Phase composition of powders and as-sprayed coatings was determined by X-ray diffraction. Electron probe microanalyzer was employed to investigate the polished and fractured surface morphologies of the coatings. Mechanical properties including microhardness, fracture toughness and bending strength were evaluated. The results indicate that the addition of Cr₂O₃ is conducive to the stabilization of α-Al₂O₃. Compared with the pure Al₂O₃ and Cr₂O₃ coatings, Al₂O₃-Cr₂O₃ composite coatings show lower porosities and denser structures. Heterogeneous nucleation of α-Al₂O₃ occurs over the isostructural Cr₂O₃ lamellae and partial solid solution of Al₂O₃ and Cr₂O₃ might be occurring as well. Furthermore, grain refining and solid solution strengthening facilitate the mechanical property enhancement of Al₂O₃-Cr₂O₃ composite coatings.     

Deposition of Al2O3-TiO2 Nanostructured Powders by Atmospheric Plasma Spraying

Al₂O₃-13%TiO₂ coatings were deposited on stainless steel substrates from conventional and nanostructured powders using atmospheric plasma spraying (APS). A complete characterization of the feedstock confirmed its nanostructured nature. Coating microstructures and phase compositions were characterized using SEM, TEM, and XRD techniques. The microstructure comprised two clearly differentiated regions. One region, completely fused, consisted mainly of nanometer-sized grains of γ-Al₂O₃ with dissolved Ti⁺⁴. The other region, partly fused, retained the microstructure of the starting powder and was principally made up of submicrometer-sized grains of α-Al₂O₃, as confirmed by TEM. Coating microhardness as well as tribological behavior were determined. Vickers microhardness values of conventional coatings were in average slightly lower than the values for nanostructured coating. The wear resistance of conventional coatings was shown to be lower than that of nanostructured coatings as a consequence of Ti segregation. A correlation between the final properties, the coating microstructure, and the feedstock characteristics is given.     

Enhanced thermoelectric properties of n-type Bi2Te3-based nanocomposite fabricated by spark plasma sintering

Highly dense n-type Bi₂Te₃-based thermoelectric materials dispersed with x vol.% γ-Al₂O₃ nanoparticles (x = 0, 0.4, 1.0, 1.5) were fabricated by spark plasma sintering method. The effects of γ-Al₂O₃ addition on microstructure and the thermoelectric properties were studied. It was found that γ-Al₂O₃ nanoparticles locate both at grain boundaries and inside Bi₂Se_0.3Te_2.7 grains. The nanoparticles induce both potential barrier scattering effect and additional phonon scattering effect, which simultaneously enhance the Seebeck coefficient and reduce the lattice thermal conductivity of the nanocomposites in the measured temperature range of 300-500 K, respectively. The maximum dimensionless figure of merit (ZT_max) reaches up to 0.99 for the sample with x = 1.0 at 400 K, which is 35% improvement over the Bi₂Te₃-based matrix. More importantly, the average ZT value of the sample increases from 0.65 to 0.91 in the temperature range 300-500 K, making the nanocomposites much more applicable in cooling and power generation.     

Electroless ternary Ni-W-P alloys containing micron size Al2O3 particles

In the present investigation electroless ternary NiWP-Al₂O₃ composite coatings were prepared using an electroless nickel bath. Second phase alumina particles (1 µm) were used to codeposit in the NiWP matrix. Nanocrystalline ternary NiWP alloys and composite coatings were obtained using an alkaline citrate based bath which was operated at pH 9 and temperature at 88 ± 2 °C. Mild steel was used as a substrate material and deposition was carried out for about 4 h to get a coating thickness of 25 ± 3 µm. Metallographic cross-sections were prepared to find out the coating thickness and also the uniform distribution of the aluminum oxide particles in NiWP matrix. Surface analysis carried out on both the coatings using scanning electron microscope (SEM) showed that particle incorporation in ternary NiWP matrix has increased the nodularity of composite coatings compared to fine nodular NiWP deposits. Elemental analysis of energy dispersive X-ray (EDX) results showed that codeposited P and W elements in plain NiWP deposit were 13 and 1.2 wt.%, respectively. There was a decrease in P content from 13 to 10 wt.% with a marginal variation in the incorporated W (1.01 wt.%) due to the codeposition of aluminum oxide particles in NiWP matrix. X-ray diffraction (XRD) studies carried out on as-plated deposits showed that both the deposits are X-ray amorphous with a grain size of around 3 nm. Phase transformation studies carried out on both the coatings showed that composite coatings exhibited better thermal stability compared to plain NiWP deposits. From the XRD studies it was found that metastable phases such as NiP and Ni₅P₂ present in the composite coatings heat treated at major exothermic peak temperature. Annealed composite coatings at various temperatures revealed higher microhardness values compared to plain NiWP deposits.