Ultrafast Flame Annealing of TiO2 Paste for Fabricating Dye‐Sensitized and Perovskite Solar Cells with Enhanced Efficiency

Mesoporous TiO₂ nanoparticle (NP) films are broadly used as electrodes in photoelectrochemical cells, dye‐sensitized solar cells (DSSCs), and perovskite solar cells (PSCs). State‐of‐the‐art mesoporous TiO₂ NP films for these solar cells are fabricated by annealing TiO₂ paste‐coated fluorine‐doped tin oxide glass in a box furnace at 500 °C for ≈30 min. Here, the use of a nontraditional reactor, i.e., flame, is reported for the high throughput and ultrafast annealing of TiO₂ paste (≈1 min). This flame‐annealing method, compared to conventional furnace annealing, exhibits three distinct benefits. First, flame removes polymeric binders in the initial TiO₂ paste more completely because of its high temperature (≈1000 °C). Second, flame induces strong interconnections between TiO₂ nanoparticles without affecting the underlying transparent conducting oxide substrate. Third, the flame‐induced carbothermic reduction on the TiO₂ surface facilitates charge injection from the dye/perovskite to TiO₂. Consequently, when the flame‐annealed mesoporous TiO₂ film is used to fabricate DSSCs and PSCs, both exhibit enhanced charge transport and higher power conversion efficiencies than those fabricated using furnace‐annealed TiO₂ films. Finally, when the ultrafast flame‐annealing method is combined with a fast dye‐coating method to fabricate DSSC devices, its total fabrication time is reduced from over 3 h to ≈10 min.     

Carbon Nanotubes for Dye‐Sensitized Solar Cells

As one type of emerging photovoltaic cell, dye‐sensitized solar cells (DSSCs) are an attractive potential source of renewable energy due to their eco–friendliness, ease of fabrication, and cost effectiveness. However, in DSSCs, the rarity and high cost of some electrode materials (transparent conducting oxide and platinum) and the inefficient performance caused by slow electron transport, poor light‐harvesting efficiency, and significant charge recombination are critical issues. Recent research has shown that carbon nanotubes (CNTs) are promising candidates to overcome these issues due to their unique electrical, optical, chemical, physical, as well as catalytic properties. This article provides a comprehensive review of the research that has focused on the application of CNTs and their hybrids in transparent conducting electrodes (TCEs), in semiconducting layers, and in counter electrodes of DSSCs. At the end of this review, some important research directions for the future use of CNTs in DSSCs are also provided.     

Metal Oxide Semiconductors for Dye‐ and Quantum‐Dot‐Sensitized Solar Cells

This Review provides a brief summary of the most recent research developments in the synthesis and application of nanostructured metal oxide semiconductors for dye sensitized and quantum dot sensitized solar cells. In these devices, the wide bandgap semiconducting oxide acts as the photoanode, which provides the scaffold for light harvesters (either dye molecules or quantum dots) and electron collection. For this reason, proper tailoring of the optical and electronic properties of the photoanode can significantly boost the functionalities of the operating device. Optimization of the functional properties relies with modulation of the shape and structure of the photoanode, as well as on application of different materials (TiO₂, ZnO, SnO₂) and/or composite systems, which allow fine tuning of electronic band structure. This aspect is critical because it determines exciton and charge dynamics in the photoelectrochemical system and is strictly connected to the photoconversion efficiency of the solar cell. The different strategies for increasing light harvesting and charge collection, inhibiting charge losses due to recombination phenomena, are reviewed thoroughly, highlighting the benefits of proper photoanode preparation, and its crucial role in the development of high efficiency dye sensitized and quantum dot sensitized solar cells.     

Anatase Mesoporous TiO2 Nanofibers with High Surface Area for Solid‐State Dye‐Sensitized Solar Cells

Mesoporous nanofibers (NFs) with a high surface area of 112 m²/g have been prepared by electrospinning technique. The structures of mesoporous NFs and regular NFs are characterized and compared through scanning electron microscope (SEM), transmission electron microscopy (TEM), X‐ray diffraction (XRD) and selected area electron diffraction (SAED) studies. Using mesoporous TiO₂ NFs as the photoelectrode, solid‐state dye‐sensitized solar cells (SDSCs) have been fabricated employing D131 as the sensitizer and P3HT as the hole transporting material to yield an energy conversion efficiency (η) of 1.82%. A J_sc of 3.979 mA cm^?2 is obtained for mesoporous NF‐based devices, which is 3‐fold higher than that (0.973 mA cm^?2) for regular NF‐based devices fabricated under the same condition (η = 0.42%). Incident photon‐to‐current conversion efficiency (IPCE) and dye‐desorption test demonstrate that the increase in J_sc is mainly due to greatly improved dye adsorption for mesoporous NFs as compared to that for regular NFs. In addition, intensity modulated photocurrent spectroscopy (IMPS) and intensity modulated photovoltage spectroscopy (IMVS) measurements indicate that the mesopores on NF surface have very minor effects on charge transport and collection. Initial aging test proves good stability of the fabricated devices, which indicates the promise of mesoporous NFs as photoelectrode for low‐cost SDSCs.     

Lessons Learned: From Dye‐Sensitized Solar Cells to All‐Solid‐State Hybrid Devices

The field of solution‐processed photovoltaic cells is currently in its second spring. The dye‐sensitized solar cell is a widely studied and longstanding candidate for future energy generation. Recently, inorganic absorber‐based devices have reached new record efficiencies, with the benefits of all‐solid‐state devices. In this rapidly changing environment, this review sheds light on recent developments in all‐solid‐state solar cells in terms of electrode architecture, alternative sensitizers, and hole‐transporting materials. These concepts are of general applicability to many next‐generation device platforms.     

Efficient and Stable Solid‐State Dye‐Sensitized Solar Cells Based on a High‐Molar‐Extinction‐Coefficient Sensitizer

The high‐molar‐extinction‐coefficient heteroleptic ruthenium dye, cis‐Ru (4,4′‐bis(5‐octylthieno[3,2‐b] thiophen‐2‐yl)‐2,2′‐bipyridine) (4,4′‐dicarboxyl‐2,2′‐bipyridine) (NCS)₂, exhibits an AM 1.5 solar (100 mW cm^?2)‐to‐electric power‐conversion efficiency of 4.6% in a solid‐state dye‐sensitized solar cell (SSDSC) with 2,2′, 7,7′‐tetrakis‐(N,N‐di‐p‐methoxyphenylamine)9,9′‐spirobifluorene (spiro‐MeOTAD) as the organic hole‐transporting material. These SSDSC devices exhibit good durability during accelerated tests under visible‐light soaking for 1000 h at 60 °C. This demonstration elucidates a class of photovoltaic devices with potential for stable and low‐cost power generation. The electron recombination dynamics and charge collection that take place at the dye‐sensitized heterojunction are studied by means of impedance and transient photovoltage decay techniques.