Synthesis and properties of novel soluble aromatic polyamides containing 4-aryl-2,6-diphenylpyridine moieties and pendant fluorinated phenoxy groups

Three diamine monomers containing pyridine groups were prepared via the modified Chichibabin reaction of aromatic aldehydes with 4′-nitroacetophenone, followed by reduction with hydrazine hydrate in the presence of Pd/C. Novel aromatic polyamides containing 4-aryl-2,6-diphenylpyridine moieties and pendant fluorinated phenoxy groups were synthesized from these diamines and two fluorinated isophthaloyl dichlorides by the low temperature solution polycondensation in N,N-dimethylacetamide (DMAc). All the polymers are amorphous and readily soluble in strong polar organic solvents such as DMAc, N-methyl-2-pyrrolidinone (NMP), N,N-dimethylformamide (DMF), and dimethyl sulfoxide (DMSO) at room temperature. The resulting polymers showed glass transition temperatures between 270 and 314 °C and 5 % weight loss temperatures ranging from 442 °C to 475 °C, and char yields at 800 °C higher than 53 % in nitrogen. These polyamides could be cast into transparent, flexible and strong films from DMAc solution with tensile strengths of 72.5–87.3 MPa, tensile moduli of 2.35–2.87 GPa, and elongations at break of 5.3–9.5 %. The polyamide films exhibited low dielectric constants of 3.21–3.54 (1 MHz), low water uptakes in the range of 1.17–1.38 %, and high transparency with an ultraviolet-visible absorption cut-off wavelength in the 380–391 nm range.     

Synthesis and characterization of polyimides from 4,4′-(3-(<Emphasis Type="Italic">tert</Emphasis>-butyl)-4-aminophenoxy)diphenyl ether

A novel diamine 4,4′-(3-(tert-butyl)-4-aminophenoxy)diphenyl ether (4) was synthesized from 2-tert-butylaniline and 4,4′-oxydiphenol through iodination, acetyl protection, coupling reaction and deacetylation protection. Then some polyimides (PIs) were obtained by one-pot polycondensation of diamne 4 with several commercial aromatic dianhydrides respectively. They all exhibit enhanced solubility in organic solvents (such as NMP, DMF, THF and CHCl₃ etc.) at room temperature. Their number-average molecular weights are in the range of (2.1–3.7)?×?10⁴ g/mol with PDI from 2.25 to 2.74 by GPC. They can form transparent, tough and flexible films by solution-casting. The light transparency of them is higher than 90% in the visible light range from 400 nm to 760 nm and the cut-off wavelengths of UV–vis absorption are below 370 nm. They also display the outstanding thermal stability with the 5% weight loss temperature from 525 °C to 529 °C in nitrogen atmosphere. The glass transition temperatures (T _g s) are higher than 264 °C by DSC. XRD results demonstrate that these PIs are amorphous polymers with the lower water absorption (<0.66%). In summary, the incorporation of tert-butyl groups and multiple phenoxy units into the rigid PI backbones can endow them excellent solubility and transparency with relatively high T _g s.     

Synthesis and properties of novel soluble polyamides containing both fluorene or xanthene cardo moieties and fluorinated phenoxy pendant groups

A series of novel aromatic polyamides containing both fluorene or xanthene cardo moieties and fluorinated phenoxy pendant groups were synthesized from two fluorinated isophthaloyl chlorides and four diamines containing cardo groups by the low‐temperature solution polycondensation in N,N‐dimethylacetamide (DMAc). The obtained polymers were characterized by different physicochemical techniques. All the polymers were amorphous and readily soluble in many organic solvents such as DMAc, N‐methyl‐2‐pyrrolidinone, N,N‐dimethylformamide, dimethyl sulfoxide, pyridine, and tetrahydrofuran at room temperature. The new fluorinated polyamides had high thermal stability with the glass transition temperatures of 237–259°C, the temperatures at 5% weight loss of 437–476°C in nitrogen. All the polymers formed transparent, strong, and flexible films with tensile strengths of 70.6–87.5 MPa, tensile moduli of 2.23–2.78 GPa, and elongations at break of 5.8–8.7%. These polyamide films had high optical transparency with an ultraviolet–visible absorption cutoff wavelength of 352–368 nm, low dielectric constants of 3.24–3.45 (1 MHz), and lower water absorptions of 1.06–1.43%. POLYM. ENG. SCI., 57:1234–1241, 2017. © 2017 Society of Plastics Engineers     

Synthesis and characterization of new rigid‐rod and organosoluble poly(amide–imide)s based on 1,4‐bis(trimellitimido)‐2,3,5,6‐tetramethylbenzene

A series of new aromatic poly(amide–imide)s (PAIs) was synthesized by triphenyl phosphite‐activated polycondensation of the diimide–diacid, 1,4‐bis(trimellitimido)‐2,3,5,6‐tetramethylbenzene (I), with various aromatic diamines in a medium consisting of N‐methyl‐2‐pyrrolidone (NMP), pyridine, and calcium chloride. The PAIs had inherent viscosities of 0.82–2.43 dL/g. The diimide–diacid monomer (I) was prepared from 2,3,5,6‐tetramethyl‐p‐phenylenediamine with trimellitic anhydride (TMA). Most of the resulting polymers showed an amorphous nature and were readily soluble in a variety of organic solvents including NMP, N,N‐dimethylacetamide (DMAc), and N,N‐dimethylformamide (DMF). Transparent, flexible, and tough films of these polymers could be cast from DMAc solutions. Their cast films had tensile strengths ranging from 80 to 95 MPa, elongation at break from 10 to 45%, and initial modulus from 2.01 to 2.50 GPa. The 10% weight loss temperatures of these polymers were above 510°C in nitrogen. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 1162–1170, 2000     

New functional copolymers of <Emphasis Type="Italic">N</Emphasis>-acryloyl-<Emphasis Type="Italic">N</Emphasis>′-methyl piperazine and 2-hydroxyethyl methacrylate: synthesis,determination of reactivity ratios and swelling characteristics of gels

Copolymers of N-acryloyl-N′-methylpiperazine (AcrNMP) and 2-hydroxyethyl methacrylate (HEMA) were synthesized by free radical solution polymerization in dioxane at 70 ± 1 °C, using 2,2′-azobisisobutyronitrile (AIBN) as initiator. The copolymer compositions were analyzed by the methods of FTIR spectroscopy and elemental analysis. Both the method of analysis yielded results that agreed reasonably well. The monomer reactivity ratios of the copolymerization were determined by the linearization methods of Finemann–Ross (FR) and Kelen–Tüdös (KT). The reactivity parameter results derived using FTIR analysis showed that the copolymerization yielded mainly alternating structure with reactivity ratios, r ₁(AcrNMP) = 0.263 ± 0.011 and r ₂(HEMA) = 0.615 ± 0.097 by F–R method and r ₁ = 0.227 ± 0.074 and r ₂ = 0.53 ± 0.15 by KT method. Microstructure data calculated by the method of Igarashi also supports the alternating structure (tendency) of the copolymer. Crosslinked polymer gels of this system exhibited remarkably high swelling of more than 500% in water at ambient temperature.     

Development of Novel Amidosulfobetaine Surfactant–Polymer Systems for EOR Applications

Experimental studies were conducted to evaluate the thermal stability and rheological properties of novel surfactant–polymer (SP) systems for enhanced oil recovery applications. One in-house synthesized amphoteric amidosulfobetaine surfactant 3-(N-pentadecanamidopropyl-N,N-dimethylammonium)propanesulfonate and three different polymers were evaluated. Polymer A was a terpolymer of acrylamide, acrylamido tert-butyl sulfonate, and acrylic acid, whereas polymers B and C were terpolymers of acrylamide, N-vinylpyrrolidone, and acrylamido tert-butyl sulfonate with different anionicity. Long-term thermal stability of the surfactant was assessed using FTIR, ¹H NMR, and ¹³C NMR. The surfactant was compatible with seawater at 90 °C and no precipitation was observed. Structural analysis showed good thermal stability and no structural changes were observed after aging at 90 °C. The effects of surfactant concentration, shear rate, salinity, and polymer concentration on rheological properties of the SP systems were determined. Polymer A showed highest viscosity among the investigated polymers in deionized and seawater. The interactions between the surfactant and polymer A were assessed using rheological measurements. In the presence of salts, the viscosity of all three polymers reduced significantly as a result of charge screening. At low shear rates, the added surfactant slightly decreased the viscosity and storage modulus of polymer A. At high shear rates, the effect of the surfactant on the viscosity and storage modulus of polymer A was insignificant.     

Nanogels of poly-N-isopropylacrylamide,poly-N,N-diethylacrylamide and acrylic acid for controlled release of thymol

Synthesis of new nanogels composed of poly N-isopropylacrylamide (PNIPAM) and poly N,N-diethylacrylamide (PNDEA) at different mole ratios of 100:0–50:50 were performed with constant acrylic acid (AA) content (NIPAM:AA mole ratio of 10:1) by free radical polymerization. The obtained nanogels were loaded with thymol and self-assembled on the surface of chitosan films to evaluate control release of the antimicrobial. The effect of temperature (8–35 °C), pH (2–8), and ions were evaluated on particle size (100–200 nm) and charge (?25--40 mv). With the increasing ratio of PNDEA in the copolymers, the lower critical solution temperature shifted gradually from 33 °C to <10 °C. When pH value decreased from 8 to 2, nanogel shrink occurred. Different ions influenced the hydrodynamic diameters of particles, causing salting out effect that followed the order of Hofmeister series. Thymol loaded within mole ratios of 50:50 of NIPAM/NDEA nanogels had longer release time (>24 h) at 4 °C than that at 25 °C (around 6 h). All thymol loaded nanogels exhibited antimicrobial activity against E. coli and B. subtilis.     

Synthesis and properties of novel polyamides containing sulfone‐ether linkages and xanthene cardo groups

In order to obtain polyamides with enhanced solubility and processability, as well as good mechanical and thermal properties, several novel polyamides containing sulfone‐ether linkages and xanthene cardo groups based on a new diamine monomer, 9,9‐bis[4‐(4‐aminophenoxy)phenyl]xanthene (BAPX), were investigated. The BAPX monomer was synthesized via a two‐step process consisting of an aromatic nucleophilic substitution reaction of readily available 4‐chloronitrobenzene with 9,9‐bis(4‐hydroxyphenyl)xanthene in the presence of potassium carbonate in N,N‐dimethylformamide, followed by catalytic reduction with hydrazine and Pd/C. Four novel aromatic polyamides containing sulfone‐ether linkages and xanthene cardo groups with inherent viscosities between 0.98 and 1.22 dL g^?1 were prepared by low‐temperature polycondensation of BAPX with 4,4′‐sulfonyldibenzoyl chloride, 4,4′‐[sulfonyl‐bis(4‐phenyleneoxy)]dibenzoyl chloride, 3,3′‐[sulfonyl‐bis(4‐phenyleneoxy)]dibenzoyl chloride and 4,4′‐[sulfonyl‐bis(2,6‐dimethyl‐1,4‐phenyleneoxy)]dibenzoyl chloride in N,N‐dimethylacetamide (DMAc) solution containing pyridine. All these new polyamides were amorphous and readily soluble in various polar solvents such as DMAc and N‐methylpyrrolidone. These polymers showed relatively high glass transition temperatures in the range 238–298 °C, almost no weight loss up to 450 °C in air or nitrogen atmosphere, decomposition temperatures at 10% weight loss ranging from 472 to 523 °C and 465 to 512 °C in nitrogen and air, respectively, and char yields at 800 °C in nitrogen higher than 50 wt%. Transparent, flexible and tough films of these polymers cast from DMAc solution exhibited tensile strengths ranging from 78 to 87 MPa, elongations at break from 9 to 13% and initial moduli from 1.7 to 2.2 GPa. Primary characterization of these novel polyamides shows that they might serve as new candidates for processable high‐performance polymeric materials. Copyright © 2010 Society of Chemical Industry     

Synthesis,Characterization and Surface Properties of Amidosulfobetaine Surfactants Bearing Odd-Number Hydrophobic Tail

Three amidosulfobetaine surfactants were synthesized namely: 3-(N-pentadecanamidopropyl-N,N-dimethyl ammonium) propanesulfonate (2a); 3-(N-heptadecanamidopropyl-N,N-dimethyl ammonium) propanesulfonate (2b), and 3-(N-nonadecanamidopropyl-N,N-dimethyl ammonium) propanesulfonate (2c). These surfactants were prepared by direct amidation of commercially available fatty acids with 3-(dimethylamino)-1-propylamine and subsequent reaction with 1,3-propanesultone to obtain quaternary ammonium salts. The synthesized surfactants were characterized by IR, NMR and mass spectrometry. Thermogravimetric analysis (TGA) results showed that the synthesized surfactants have excellent thermal stability with no major thermal degradation below 300 °C. The critical micelle concentration (CMC) values of the surfactants 2a and 2b were found to be 2.2 × 10^?4 and 1.04 × 10^?4 mol/L, and the corresponding surface tension (γ_CMC) values were 33.14 and 34.89 mN m^?1, respectively. The surfactants exhibit excellent surface properties, which are comparable with conventional surfactants. The intrinsic viscosity of surfactant (2b) was studied at various temperatures and concentrations of multi-component brine solution. The plot of natural logarithm of relative viscosity versus surfactant concentration obtained from Higiro et al. model best fit the surfactant behavior. Due to good salt resistance, excellent surface properties and thermal stability, the synthesized surfactant has potential to be used in various oil field applications such as enhanced oil recovery, fracturing, acid diversion, and well stimulation.     

Seasonal N<Subscript>2</Subscript>O emissions respond differently to environmental and microbial factors after fertilization in wheat–maize agroecosystem

Biogeochemical processes regulating cropland soil nitrous oxide (N₂O) emissions are complex, and the controlling factors need to be better understood, especially for seasonal variation after fertilization. Seasonal patterns of N₂O emissions and abundances of archaeal ammonia monooxygenase (amoA), bacterial amoA, nitrate reductase (narG), nitrite reductase (nirS/nirK), and nitrous oxide reductase (nosZ) genes in long-term fertilized wheat–maize soils have been studied to understand the roles of microbes in N₂O emissions. The results showed that fertilization greatly stimulated N₂O emission with higher values in pig manure-treated soil (OM, 2.88 kg N ha^?1 year^?1) than in straw-returned (CRNPK, 0.79 kg N ha^?1 year^?1) and mineral fertilizer-treated (NPK, 0.90 kg N ha^?1 year^?1) soils. Most (52.2–88.9%) cumulative N₂O emissions occurred within 3 weeks after fertilization. Meanwhile, N₂O emissions within 3 weeks after fertilization showed a positive correlation with narG gene copy number and a negative correlation with soil NO₃^? contents. The abundances of narG and nosZ genes had larger direct effects (1.06) than ammonium oxidizers (0.42) on N₂O emissions according to partial least squares path modeling. Stepwise multiple regression also showed that log narG was a predictor variable for N₂O emissions. This study suggested that denitrification was the major process responsible for N₂O emissions within 3 weeks after fertilization. During the remaining period of crop growth, insufficient N substrate and low temperature became the primary limiting factors for N₂O emission according to the results of the regression models.     

Ultra-repellency of Al surfaces: design and evaluation

Aluminum (Al) surfaces with ultra-repellency as well as desirable robustness were designed and fabricated. With photolithographic patterning of a thick SU-8 layer and sputtering of a thin Al film, re-entrant micro-pillar textured Al surfaces were prepared. After derivatization with perfluoroalkyl phosphoric acid (FPA), the textured Al surfaces showed ultra-repellency for a wide variety of liquids. The contact angles (CAs) of deionized (DI) water, hexadecane and dodecane were larger than 150°, and those of methanol and ethanol were larger than 100°. The sliding angles (SAs) of DI water, hexadecane and dodecane were 5°, 10°, and 10°, respectively, showing excellent superamphiphobicity. The SAs of methanol and ethanol were in the range of 20°–30°. The robustness of the ultra-repellent Al surface was evaluated by three parameters: robust height (H*), robust angle (T*) and robust factor (A*). For the DI water probing, the values of the parameters are H* ≈ 403, T* ≈ 119 and A* ≈ 92, respectively, indicative of a desirable robustness. We clarified that only re-entrant structures can support composite liquid–solid–vapor interfaces when the corresponding Young’s CAs are smaller than 90°, and the function of the nanometer structures of the hierarchical textures which were widely adopted to fabricate superamphiphobic surfaces is to help construct re-entrant structures. FPA derivatization is effective in lowering the surface energy of Al surfaces, combining with re-entrant textures to provide a simple and high throughput approach to ultra-repellency for a wide variety of liquids.     

Synthesis and characterization of polyphenylene vinylenes having <Emphasis Type="Italic">m</Emphasis>-terphenyl group: comparison of their optical properties

A series of alternate block copolymers of polyphenylene vinylenes that have 1,3-dioctyloxy phenylene in the center of kinked m-terphenyl group as one of the building blocks with either one of the aromatic groups, viz., 1,4-dioctyloxy benzene, 4,6-dioctyloxy benzene and 4,4′-dioctyloxy biphenyl, was synthesized through Heck polymerization. These alternate block copolymers, viz., poly(2,5-bis(octyloxy)phenylene vinylene alt 4′,6′-bis(octyloxy)-1,1′:3′,1″-terphenylene) (P1), poly(2,4-bis(octyloxy)phenylene vinylene alt 4′,6′-bis(octyloxy)-1,1′:3′,1″-terphenylene) (P2) and poly(4,4′-bis(octyloxy-3,3′-biphenylene vinylene alt 4′,6′-bis(octyloxy)-1,1′:3′,1″-terphenylene) (P3), were characterized for their thermal and optical properties. The synthesized polymers had good solubility in organic solvents and were stable up to 350 °C. The molecular weights of the synthesized polymers were in the range 4370–10,900 Da with polydispersity range 1.52–1.65, which were measured by the gel permeation chromatography technique. The optical properties of these polymers showed absorptions in solution at around 400, 329, and 345 nm for P1, P2, and P3 polymers, respectively. The photoluminescence emission maxima of the polymers were at around 461 nm with a shoulder 439 and 424 nm for P1, P2, and P3, respectively. Photoluminescence emission of films of these polymers showed minimum redshift (20 nm) when compared with spectra of their solutions. The optical and photoluminescence emission properties of these polymers were found to vary on the backbone structure.     

Bio-/Environment-Friendly Cationic Gemini Surfactant as Novel Corrosion Inhibitor for Mild Steel in 1 M HCl Solution

Bio-/environment-friendly cationic gemini surfactant, ethane-1,2-diyl bis(N,N-dimethyl-N-hexadecylammoniumacetoxy)dichloride, referred to as 16-E2-16, was synthesized and characterized. Corrosion inhibition effects of 16-E2-16 on mild steel (MS) surface in 1 M HCl solution at 30, 40, 50 and 60 °C were evaluated using gravimetric analysis, potentiodynamic polarisation and electrochemical impedance spectroscopy measurements. The nature of the protective inhibitor film formed on the MS surface was analysed by SEM, EDAX and FT-IR, while TGA was used to assure the thermal behaviour and stability of the film at high temperature. The formation of [inhibitor-Fe²⁺] on the surface of MS was confirmed by UV–visible spectroscopy. The inhibition efficiency of the studied inhibitor increased with increasing concentration and solution temperature. The compound behaved as a mixed type inhibitor and acted by blocking the electrode surface by means of adsorption obeying the Langmuir adsorption isotherm. Surface active properties and corrosion inhibition effects of 16-E2-16 in the presence of inorganic (NaI) and organic (NaSal) salts were also investigated and are discussed. Density functional theory calculations have been carried out to correlate the efficiency of the compound with its intrinsic molecular parameters.     

Aqueous radical polymerization of <Emphasis Type="Italic">N</Emphasis>,<Emphasis Type="Italic">N</Emphasis>-dimethylacrylamide redox-initiated by aerobically catalytic oxidation of water-soluble tertiary amines

Catalytic oxidation of water-soluble tertiary amines by complexes of Cu^II, Fe^III and Co^II was utilized to initiate radical polymerization of N,N-dimethylacrylamide (DMAAm) in aqueous solution at 70–80 °C. The oxidation of tertiary amines by Cu^II was studied by proton nuclear magnetic resonance spectroscopy and online ultraviolet–visible spectrophotometry. The polymerization kinetics was monitored by gas chromatography, and molecular weight of the PDMAAm was measured by gel-permeation chromatography coupled with multi-angle laser light scattering. Oxidation of tertiary amines occurs predominantly via formation of C_alpha·radicals to initiate polymerization of electron-deficient monomers and N-dealkylation, and redox equilibrium between Cu^I/L and Cu^II/L is established at a faster rate in aqueous media. Fe^III and Cu^II complexes are efficient catalysts as each catalyst molecule could generate above 10 propagating radicals in 5 h, while Co^II complex might involve in oxidation of tertiary amines in non-radical pathway, leading to a low catalytic efficiency. Water-soluble tertiary amines such as N,N-dialkylethanolamine (alkyl = methyl, ethyl etc.) are reducing agents of a higher activity in aqueous media than those primary or secondary analogues. Our strategy renders it possible to prepare polymer of alpha-amino functionality via one-pot process from commercially available commodity reagents under practical conditions with negligible catalyst residue.     

Amorphous polyamide coating resins from sugar-derived monomers

In this article, the synthesis of bio-based polyamides for powder coating applications and their evaluation in a solventborne coating system are reported. The M _n values of the resins were between 3000 and 4000 g mol^?1 and the resins displayed T _g values from 60 to 80°C. Both amine and carboxylic acid functionalities (total ~0.6 mmol g^?1) were introduced for curing purposes. The resins were cured with triglycidyl isocyanurate (TGIC) or N,N,N′,N′-tetrakis(2-hydroxyethyl)adipamide (Primid XL-552). The curing reaction was followed using rheology which indicated that TGIC achieved higher reaction rates and higher gel contents. The DSC analysis of the cured disks showed that all cured samples were amorphous as is desired for the targeted coating application. The resins required a curing temperature higher than 150°C. Aluminum panels were coated using a solventborne approach and the coatings were cured at 180°C during 1 h. Dewetting was observed on all panels. Network formation was adequate for an amine-functional resin cured with TGIC as indicated by solvent resistance testing. In conclusion, the developed bio-based polyamide resins are promising materials to be used as binder resins in powder coating applications.     

Lipid Transfer to HDL is Higher in Marathon Runners than in Sedentary Subjects,but is Acutely Inhibited During the Run

Although exercise increases HDL-cholesterol, exercise-induced changes in HDL metabolism have been little explored. Lipid transfer to HDL is essential for HDL’s role in reverse cholesterol transport. We investigated the effects of acute exhaustive exercise on lipid transfer to HDL. We compared plasma lipid, apolipoprotein and cytokine levels and in vitro transfer of four lipids from a radioactively labeled lipid donor nanoemulsion to HDL in sedentary individuals (n = 28) and in marathon runners (n = 14) at baseline, immediately after and 72 h after a marathon. While HDL-cholesterol concentrations and apo A1 levels were higher in marathon runners, LDL-cholesterol, apo B and triacylglycerol levels were similar in both groups. Transfers of non-esterified cholesterol [6.8 (5.7–7.2) vs. 5.2 (4.5–6), p = 0.001], phospholipids [21.7 (20.4–22.2) vs. 8.2 (7.7–8.9), p = 0.0001] and triacylglycerol [3.7 (3.1–4) vs. 1.3 (0.8–1.7), p = 0.0001] were higher in marathon runners, but esterified-cholesterol transfer was similar. Immediately after the marathon, LDL- and HDL-cholesterol concentrations and apo A1 levels were unchanged, but apo B and triacylglycerol levels increased. Lipid transfer of non-esterified cholesterol [6.8 (5.7–7.2) vs. 5.8 (4.9–6.6), p = 0.0001], phospholipids [21.7 (20.4–22.2) vs. 19.1 (18.6–19.3), p = 0.0001], esterified-cholesterol [3.2 (2.2–3.8) vs. 2.3 (2–2.9), p = 0.02] and triacylglycerol [3.7 (3.1–4) vs. 2.6 (2.1–2.8), p = 0.0001] to HDL were all reduced immediately after the marathon but returned to baseline 72 h later. Running a marathon increased IL-6 and TNF-α levels, but after 72 h these values returned to baseline. Lipid transfer, except esterified-cholesterol transfer, was higher in marathon runners than in sedentary individuals, but the marathon itself acutely inhibited lipid transfer. In light of these novel observations, further study is required to clarify how these metabolic changes can influence HDL composition and anti-atherogenic function.     

Synthesis and properties of novel aromatic polyamides with xanthene cardo groups

Two novel monomers, 9,9‐bis[4‐(4‐carboxyphenoxy)phenyl]xanthene (BCAPX) and 9,9‐bis[4‐(4‐aminophenoxy)phenyl]xanthene (BAPX) were prepared in two main steps starting from nucleophilic substitution of 9,9‐bis(4‐hydroxyphenyl)xanthene (BHPX) with p‐fluorobenzonitrile and p‐chloronitrobenzene, respectively. Using triphenyl phosphite and pyridine as condensing agents, two series of polyamides containing xanthene cardo groups with the inherent viscosities (0.82–1.32 dL/g) were prepared by polycondensation from BCAPX with various aromatic diamines or from BAPX with various aromatic dicarboxylic acids in an N‐methyl‐2‐pyrrolidone (NMP) solution containing dissolved calcium chloride, respectively. All new polyamides were amorphous and readily soluble in various polar solvents such as N,N‐dimethylformamide (DMF), NMP, N,N‐dimethylacetamide (DMAc) and pyridine. These polymers showed relatively high glass transition temperatures between 264 and 308°C, decomposition temperatures at 10% weight loss ranging from 502 to 540°C and 488 to 515°C in nitrogen and air, respectively, and char yields at 800°C in nitrogen higher than 56%. Transparent, flexible, and tough films of these polymers cast from DMAc solutions exhibited tensile strengths ranging from 86 to 109 MPa, elongations at break from 13 to 22%, and initial moduli from 2.15 to 2.63 GPa. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Thermal stability,solubility, and fluorescence property of poly(arylene ether ketone)s bearing <Emphasis Type="Italic">N</Emphasis>-arylenebenzimidazole units

A series of novel random poly(arylene ether ketone)s containing N-arylenebenzimidazolyl groups with precise structures in high yields were synthesized from 2-(2′-hydroxyphenyl) benzimidazole and 4,4′-dihydroxybenzophenone with 4,4′-difluorobenzophenone via nucleophilic substitution polycondensation reaction using sulfolane as a solvent. The reaction was carried out at 210 °C in the presence of anhydrous potassium carbonate. The structures of the resulted polymers were characterized by means of FT-IR, ¹H NMR spectroscopy, and elemental analysis, and the results were largely consistent with the proposed structure. X-ray diffraction studies revealed that the incorporation of N-arylenebenzimidazolyl groups decreased the crystallinity of the resulted polymers. As the benzimidazole unit content in the copolymer increased, the solubility and thermal behavior of the prepared polymers improved. The novel poly(arylene ether ketone)s exhibited glass transition temperatures (T _gs) in the range 188–237°C, and there was a good linearity relationship between T _g values and the content of benzimidazolyl groups. The 5% decomposition temperatures were within the range of 512–539 °C in nitrogen and 496–540 °C in air indicating their good thermal stability. Tensile tests of the films showed that these polymers have desirable mechanical properties. Moreover, the resulting polymers showed good fluorescence properties.     

Electrospinning of chitosan/PVA nanofibrous membrane at ultralow solvent concentration

In this work, chitin flakes were deacetylated with 50% (w/v) sodium hydroxide under nitrogen atmosphere at 120 °C for 80 min to obtain chitosan. The chitosan produced was characterized for degree of deacetylation (DD) and molecular weight. Chitosan with the DD of 78–80% was reproducibly obtained. Molecular weight showed an inverse relationship with concentration of NaOH. Chitosan nanofibrous membrane was prepared via the electrospinning of chitosan/polyvinyl alcohol (CH/PVA) aqueous solutions with varying blend compositions. The characteristics of CH/PVA nanofibrous membranes were studied as a function of viscosity of solution and applied voltage. A uniform nanofibrous membrane of average fibre diameter of 80–300 nm was obtained with blend of 2% (w/v) chitosan solution in 1% (v/v) acetic acid and 5% (w/v) PVA in distilled water in the electric field of 20–25 kV with varying proportion of CH/PVA. With the CH/PVA mass ratios; 40/60 to 10/90, electrospinning of nanofibres could be done. The electrospun nanofibrous membrane was analyzed by scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and Thermo gravimetric analysis (TGA). SEM images showed that the morphology and diameter of the nanofibres were mainly affected by the weight ratio of CH/PVA. XRD and FTIR confirmed the strong intermolecular hydrogen bonding between the molecules of Chitosan and PVA.     

Mechanistic studies of methyl methacrylate polymerization in the presence of cobalt complex with sterically-hindered redox-active ligand

The influence of bis[4,6-di-tert-butyl-N-(2,6-dimethylphenyl)-o-iminobenzosemiquinono]cobalt (II) on radical polymerization of methyl methacrylate initiated by AIBN at 70–90 °C was studied. The introduction of cobalt complex bearing redox ligands into reaction media allows to provide polymerization of methyl methacrylate without self-acceleration with linear increase of molecular weight with conversion giving polymers with relatively low molecular weight distribution. The results of IR and NMR spectrometry and MALDI mass spectroscopy measurements show that the possibility of β-hydrogen transfer between complex and propagating radical during polymerization is minimal. The electron donating additives as tert.-butyl amine and pyridine have no activating effect on polymerization. The results of our experiments provided at different concentrations of initiator show that polymerization proceeds via degenerative chain transfer mechanism.