Poly(ethylene‐co‐vinyl acetate)‐graft‐poly(methyl methacrylate) (EVA‐graft‐PMMA) as a modifier of epoxy resins

Conventional approaches to toughen thermosets are: (1) the polymerization‐induced phase separation of a rubber or a thermoplastic, or (2) the use of a dispersion of preformed particles in the initial formulation. In the present study it is shown that it is possible to combine both techniques by using graft copolymers with one of the blocks being initially immiscible and the other that phase separates during polymerization. This is illustrated by the use of poly(ethylene‐co‐vinyl acetate)‐graft‐poly(methyl methacrylate) (EVA‐graft‐PMMA) as modifier of an epoxy resin. EVA is initially immiscible and PMMA phase separates during polymerization. Blends of an epoxy monomer based on diglycidylether of bisphenol A (DGEBA, 100 parts by weight), piperidine (5 parts by weight), and PMMA (5 parts by weight), showed the typical polymerization‐induced phase separation of PMMA‐rich domains before gelation of the epoxy network. Replacing PMMA by EVA‐graft‐PMMA (5 parts by weight), yielded stable dispersions of EVA blocks, favoured by the initial solubility of PMMA blocks. Phase separation of PMMA blocks in the course of polymerization led to a dispersion of in situ generated biphasic particles (plausibly composed of EVA cores surrounded by PMMA shells), with average diameters varying from 0.3 to 0.6 µm with the cure temperature. This procedure may be used to generate stable dispersions of biphasic particles for toughening purposes. © 2002 Society of Chemical Industry     

Polymerization of methyl methacrylate in the presence of a nonpolar hydrocarbon solvent. I. Construction of a complete ternary phase diagram through an in situ polymerization

This article presents the ternary phase diagram for methyl methacrylate (MMA), poly(methyl methacrylate) (PMMA), and n‐hexane system at 70°C. It was constructed by both theoretical calculations and online laser light scattering (LLS) technique. In situ polymerization of MMA in a nonpolar nonsolvent carried out in a LLS cell provides a new means for the accurate detection of the cloud points of highly viscous polymer mixtures, with polymer weight fractions over 0.6. The ternary phase diagram measured in this study can be used to design the reaction conditions for the precipitation and/or dispersion polymerization in a nonpolar nonsolvent medium where polymerization kinetics as well as polymer particle morphologies are strongly affected by thermodynamic phase separation phenomena. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Rheological and curing behavior of reactive blending. II. Natural rubber‐g‐poly(methyl methacrylate)–cassava starch

Graft copolymers of natural rubber (NR) and methyl methacrylate (MMA) were prepared using cumene hydroperoxide and tetraethylene pentamine as redox initiators via the semibatch emulsion polymerization technique. Various molar percentage ratios of NR/MMA were studied in the grafting reaction (i.e., 95/5, 90/10, 80/20, 70/30, and 60/40). The graft copolymer with a 70/30 molar ratio was selected and used to prepare rubber blends with cassava starch. The starch was used at levels of 0, 20, 40, and 60 phr. Another set of rubber blends was prepared for comparison purposes. The NR‐g‐poly(MMA) (PMMA, 75 phr) was blended with 25 phr of NR air dried sheets (ADS) and a given level of the cassava starch. We found that the Mooney viscosity, shear stress, and shear viscosity increased with an increasing concentration of cassava starch. This may be attributed to the chemical interactions between the polar groups of the NR‐g‐PMMA and the cassava starch. The blends were later compounded using a compounding formulation according to ASTM D 3184‐89. A similar short delay onset of vulcanization (i.e., approximately 1 min) was observed for the whole set of compounds under study. However, different curing characteristics were observed for the blends of NR‐g‐PMMA–cassava starch and NR‐g‐PMMA–ADS–cassava starch. The NR‐g‐PMMA–cassava starch compounds exhibited two‐stage curing characteristics. The curing curve had a slight reversion at a testing time of approximately 8 min. The shear modulus then abruptly increased with an increasing testing time in the range of 20–60 min. The curing curves for NR‐g‐PMMA–ADS–cassava starch blends exhibited a single curing stage with a shear modulus that increased slightly with the testing time was increased from 20 to 60 min. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1453–1463, 2003     

Photo‐Induced atom transfer radical polymerization with nanosized α‐Fe2O3 as photoinitiator

Photo‐induced atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) was achieved in poly(ethylene glycol)‐400 with nanosized α‐Fe₂O₃ as photoinitiator. Well‐defined poly(methyl methacrylate) (PMMA) was synthesized in conjunction with ethyl 2‐bromoisobutyrate (EBiB) as ATRP initiator and FeCl₃·6H₂O/Triphenylphosphine (PPh₃) as complex catalyst. The photo‐induced polymerization of MMA proceeded in a controlled/living fashion. The polymerization followed first‐order kinetics. The obtained PMMA had moderately controlled number‐average molecular weights in accordance with the theoretical number‐average molecular weights, as well as narrow molecular weight distributions (M_w/M_n). In addition, the polymerization could be well controlled by periodic light‐on–off processes. The resulting PMMA was characterized by ¹H nuclear magnetic resonance and gel permeation chromatography. The brominated PMMA was used further as macroinitiator in the chain‐extension with MMA to verify the living nature of photo‐induced ATRP of MMA. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42389.     

Phase behavior and properties of poly(methyl methacrylate)/poly(vinyl acetate) blends prepared via in situ polymerization

Polymer blends composed of poly(methyl methacrylate) (PMMA) and poly(vinyl acetate) (PVAc) were prepared via radical-initiated polymerization of methyl methacrylate (MMA) in the presence of PVAc. Differential scanning calorimetry and dynamic mechanical analysis were employed to investigate the miscibility and phase behavior of the blends. The PMMA/PVAc blends of in situ polymerization were found to be phase separated and exhibited a two-phase structure, although some chain transferring reaction between the components occurred. The phase separation resulted from the solvent effect of MMA during the in situ polymerization, which was confirmed by the investigation of phase behavior based on solution cast blending. Solubility analysis of the polymerized blends indicated that some chain transferring reaction between the components occurred during the polymerization. An abrupt increase in gel content from 21.2 to 72.4 wt % was observed when the inclusion of PVAc increased from 30 to 40 wt %, and the gel component consisted of the component polymers as shown by infrared spectroscopy studies. The thermogravimetric analysis study indicated that the inclusion of a small amount of PVAc gives rise to a marked stabilization effect on the thermal stability. The PMMA/PVAc blends exhibited increased notched impact properties with the inclusion of 5 wt % PVAc. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 675–684, 1998     

The effects of polymer‐nanofiller interactions on the dynamical mechanical properties of PMMA/CaCO3 composites prepared by microemulsion template

We prepared novel poly(methyl methacrylate) (PMMA)/CaCO₃ nanocomposites by using reverse micelle as a template. The nanoparticles of CaCO₃ were prepared by the reverse microemulsion with functional monomer, methyl methacrylate (MMA) as oily phase, and the PMMA/CaCO₃ nanocomposite was obtained via polymerization of MMA monomer. The SEM image showed that the nanoparticles of CaCO₃ were dispersed in the polymer matrix. Dynamic mechanical analysis (DMTA) was performed to investigate the interaction between the nanoparticles and the polymer chains. In the low‐temperature ripening process, two tan δ peaks were observed in the nanocomposite, corresponding to the glass transitions of the matrix and the interface layer. In the high‐temperature ripening process, only one tan δ peak was observed, suggesting that the interface layer forms a continuous phase. The nanoparticles behave as a physical crosslinker in the interface layer. Modification of the surface of nanoparticles with polyacrylamide and poly(N,N′‐methylenedisacrylamide) in the nanocomposite did not show an appreciable effect on the interaction of nanoparticles with the matrix. Upon removal of the aqueous phase around the nanoparticles, we obtained surface‐capped nanoparticles by using an improved reverse microemulsion technique. Another PMMA/CaCO₃ nanocomposite was also obtained with these modified nanoparticles. DMTA analysis of this nanocomposite demonstrated that the aqueous phase layer around the nanoparticles does not significantly affect the interaction between the nanoparticles and the polymer chains. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2739–2749, 2004     

Synthesis and characterization of diblock,triblock, and multiblock copolymers containing poly(3‐hydroxy butyrate) units

A poly[(R,S)‐3‐hydroxybutyrate] macroinitiator (PHB‐MI) was obtained through the condensation reaction of poly[(R,S)‐3‐hydroxybutyrate] (PHB) oligomers containing dihydroxyl end functionalities with 4,4′‐azobis(4‐cyanopentanoyl chloride). The PHB‐MI obtained in this way had hydroxyl groups at two end of the polymer chain and an internal azo group. The synthesis of ABA‐type PHB‐b‐PMMA block copolymers [where A is poly(methyl methacrylate) (PMMA) and B is PHB] via PHB‐MI was accomplished in two steps. First, multiblock active copolymers with azo groups (PMMA‐PHB‐MI) were prepared through the redox free‐radical polymerization of methyl methacrylate (MMA) with a PHB‐MI/Ce(IV) redox system in aqueous nitric acid at 40°C. Second, PMMA‐PHB‐MI was used in the thermal polymerization of MMA at 60°C to obtain PHB‐b‐PMMA. When styrene (S) was used instead of MMA in the second step, ABCBA‐type PMMA‐b‐PHB‐b‐PS multiblock copolymers [where C is polystyrene (PS)] were obtained. In addition, the direct thermal polymerization of the monomers (MMA or S) via PHB‐MI provided AB‐type diblocks copolymers with MMA and BCB‐type triblock copolymers with S. The macroinitiators and block copolymers were characterized with ultraviolet–visible spectroscopy, nuclear magnetic resonance spectroscopy, gel permeation chromatography, cryoscopic measurements, and thermogravimetric analysis. The increases in the intrinsic viscosity and fractional precipitation confirmed that a block copolymer had been obtained. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1789–1796, 2004     

Morphology–composition–processing relationships in poly(methyl methacrylate)–polytriethylene glycol dimethacrylate shrinkage‐controlled blends

An innovative method to control shrinkage in polymer blends, by using N,N‐dimethyl‐p‐toluidine to produce phase separation in an acrylic system, was applied to synthesize polymer blends from polymethyl methacrylate (PMMA) and polytriethylene glycol dimethacrylate (PTEGDMA). The morphology of several compositions, as analyzed by scanning electron microscopy, reveals microdomains as a function of the specific composition, in contrast to conventional MMA–TEGDMA copolymers synthesized by thermal decomposition of benzoyl peroxide, used here as reference materials. Micro‐Raman and DSC analyses were also carried out to support the electron microscopy results as well. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1254–1260, 2004     

Polymerization of methyl methacrylate with a thermal iniferter: Diethyl 2,3‐dicyano‐2,3‐di(p‐tolyl)succinate

A hexa‐substituted ethane type compound, diethyl‐2,3‐dicyano‐2,3‐di(p‐tolyl)succinate (DCDTS), was successfully synthesized and used for initiation of methyl methacrylate (MMA) polymerization. The reaction demonstrated the characteristics of a “living” polymerization; i.e., both the yield and the molecular weight of the resulting polymers increased linearly with increasing reaction time, the molecular‐weight distribution of PMMA obtained was ～1.60 and almost unaffected by the conversion, and the resultant polymer can be chain extended by adding fresh MMA. End group analysis of the resultant PMMA confirmed that DCDTS behaves as a thermal iniferter for MMA polymerization. A block copolymer was prepared from the resultant PMMA, which contains a hexa‐substituted C? C bond functional end group. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2566–2572, 2001     

Effect of in situ polymerization conditions of methyl methacrylate on the structural and morphological properties of poly(methyl methacrylate)/poly(acrylonitrile‐g‐(ethylene‐co‐propylene‐co‐diene)‐g‐styrene) PMMA/AES Blends

In this study, the structural and morphological properties of poly(methyl methacrylate)/poly(acrylonitrile‐g‐(ethylene‐co‐propylene‐co‐diene‐g‐styrene) (PMMA‐AES) blends were investigated with emphasis on the influence of the in situ polymerization conditions of methyl methacrylate. PMMA‐AES blends were obtained by in situ polymerization, varying the solvent (chloroform or toluene) and polymerization conditions: method A—no stirring and air atmosphere; method B—stirring and N₂ atmosphere. The blends were characterized by infrared spectroscopy (FTIR), transmission electron microscopy (TEM), and dynamic mechanical analysis (DMA). The results showed that the PMMA‐AES blends are immiscible and present complex morphologies. This morphology shows an elastomeric dispersed phase in a glassy matrix, with inclusion of the matrix in the elastomer domains, suggesting core shell or salami morphology. The occlusion of the glassy phase within the elastomeric domains can be due to the formation of graft copolymer and/or phase inversion during polymerization. However, this morphology is affected by the polymerization conditions (stirring and air or N₂ atmosphere) and by the solvent used. The selective extraction of the blends' components and infrared spectroscopy showed that crosslinked and/or grafting reactions occur on the elastomer chains during MMA polymerization. The glass transition of the elastomer phase is influenced by morphology, crosslinking, and grafting degree and, therefore, T_g depends on the polymerization conditions. On the other hand, the behavior of T_g of the glassy phase with blend composition suggests miscibility or partial miscibility for the SAN phase of AES and PMMA. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Graft copolymerization of methyl methacrylate from brominated poly(isobutylene‐co‐isoprene) via atom transfer radical polymerization

Commercial brominated poly(isobutylene‐co‐isoprene) (BIIR) rubber has been directly used for the initiation of atom transfer radical polymerization (ATRP) by utilizing the allylic bromine atoms on the macromolecular chains of BIIR. The graft copolymerization of methyl methacrylate (MMA) from the backbone of BIIR which was used as a macroinitiator was carried out in xylene at 85 °C with CuBr/N,N,N′,N″,N″‐pentamethyldiethylenetriamine as a catalytic complex. The polymerization conditions were optimized by adjusting the catalyst and monomer concentration to reach a higher monomer conversion and meanwhile suppress macroscopic gelation during the polymerization process. This copolymerization followed a first‐order kinetic behavior with respect to the monomer concentration, and the number‐average molecular weight of the grafted poly(methyl methacrylate) (PMMA) increased with reaction time. The resultant BIIR‐graft‐PMMA copolymers showed phase separation morphology as characterized by atomic force microscopy, and the presence of PMMA phase increased the polarity of the BIIR copolymers. This study demonstrated the feasibility of using commercial BIIR polymer directly as a macromolecular initiator for ATRP reactions, which opens more possibilities for BIIR modifications for wider applications. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43408.     

Synthesis of PMMA‐PTHF‐PMMA and PMMA‐PTHF‐PST linear and star block copolymers

Combination of cationic, redox free radical, and thermal free radical polymerizations was performed to obtain linear and star polytetramethylene oxide (poly‐THF)‐polymethyl methacrylate (PMMA)/polystyrene (PSt) multiblock copolymers. Cationic polymerization of THF was initiated by the mixture of AgSbF₆ and bis(4,4′ bromo‐methyl benzoyl) peroxide (BBP) or bis (3,5,3′,5′ dibromomethyl benzoyl) peroxide (BDBP) at 20°C to obtain linear and star poly‐THF initiators with M_w varying from 7,500 to 59,000 Da. Poly‐THF samples with hydroxyl ends were used in the methyl methacrylate (MMA) polymerization in the presence of Ce(IV) salt at 40°C to obtain poly(THF‐b‐MMA) block copolymers containing the peroxide group in the middle. Poly(MMA‐b‐THF) linear and star block copolymers having the peroxide group in the chain were used in the polymerization of methyl methacrylate (MMA) and styrene (St) at 80°C to obtain PMMA‐b‐PTHF‐b‐PMMA and PMMA‐b‐PTHF‐b‐PSt linear and star multiblock copolymers. Polymers obtained were characterizated by GPC, FT‐IR, DSC, TGA, ¹H‐NMR, and ¹³C‐NMR techniques and the fractional precipitation method. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 219–226, 2004     

Methyl methacrylate based copolymers and terpolymers: Preparation,identification, and plasticizing capability for a poly(methyl methacrylate) used in aviation

In this study, we first synthesized transparent poly(methyl methacrylate–maleic anhydride) [P(MMA–MAH)] and poly(methyl methacrylate–maleic anhydride–N‐2‐methyl‐4‐nitrophenyl maleimide) [P(MMA–MAH–MI)] via free‐radical polymerization at different monomer ratios. The synthesized polymers were characterized by titration, viscometric, spectroscopy, and thermal analyses. Higher contents of maleic anhydride (MAH) resulted in increases in the viscosity, glass‐transition temperature (T_g), and transparency. The synthesized polymers were then blended with a commercial‐grade poly(methyl methacrylate) (PMMA) used in aviation in the presence of CHCl₃. According to the free volume theory, the incorporation of 5 wt % P(MMA–MAH)s or P(MMA–MAH–MI)s into the commercial PMMA resulted in a plasticizing impact on this thermoplastic, which was confirmed by the decrease in the T_g values of the blends with almost the same transparency as the initial PMMA. In fact, the higher the content of MAH was, the lower the T_g of the blends was. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46603.     

Free radical polymerizations of some vinyl monomers in carbon dioxide fluid

The effect of pressure ranging from ambient atmosphere to 28.5 MPa on the free radical polymerizations of methyl methacrylate (MMA) in carbon dioxide (CO₂) was investigated and discussed. The poly(methyl methacrylate) (PMMA) with high molecular weight was synthesized at quite high conversion of MMA in the polymerization at or below 9.2 MPa, as compared to those polymerized under 11.8–28.5 MPa. A phase transition behavior of MMA‐CO₂ binary mixture from homogeneous state to vapor‐liquid equilibrium (VLE) state was observed below 10.51 MPa. In such a VLE system, almost all MMA was found to exist in the liquid phase with higher concentration than that in homogenous system. Thus, the fast polymerization rate of MMA and high molecular weight of PMMA could be related to the VLE state of MMA/CO₂ under low pressure. Similar phenomena were also observed in the polymerization systems of styrene and vinyl acetate in CO₂, respectively. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Swelling and drying kinetics of polytetrahydrofuran and polytetrahydrofuran–poly (methyl methacrylate) gels: A photon transmission study

A bifunctional polytetrahydrofuran (PTHF) macromonomer was synthesized by termination of the living polymerization of tetrahydrofuran (THF) initiated by triflic anhydride and the subsequent termination by sodium methacrylate. The PTHF macromonomer thus prepared was polymerized and copolymerized with methyl methacrylate (MMA) by free‐radical polymerization to yield a network and a segmented network of PTHF, both being homogeneous, respectively. These PTHF and PTHF–PMMA gels were used for swelling experiments in chloroform and chloroform vapor. Drying processes were monitored after removing the gels from the solvent and solvent vapor. Photon transmission from PTHF and PTHF–PMMA gels was monitored during swelling and drying processes using a UV‐visible (UVV) spectrophotometer. Transmitted light intensities, I_tr, from these gels increased when they were immersed in chloroform and/or subjected to its vapor. The increase in I_tr was attributed to the homogeneous lattice structure of PTHF and PTHF–PMMA gels which appeared during swelling. The increase in I_tr was modeled using the Li–Tanaka equation from which time constants, τ₁, and cooperative diffusion coefficients, D_C, were determined. A decrease in I_tr after removing choloform and/or its vapor from the cell was observed and attributed to the decrease in homogeneity of lattice structures during drying of the corresponding gels. Time constants, τ2, for the drying processes were also determined. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 632–640, 2003     

The potential of Cu(I)Cl/2,2′‐bipyridine catalysis in a triblock copolymer preparation by atom transfer radical polymerization

The ability of atom transfer radical polymerization (ATRP) in the sequential synthesis of triblock copolymers was examined using Cu(I)Cl/2,2′‐bipyridine catalysis at 110°C in toluene, starting from PMMA macroinitiators terminated with the C‐Br group. The PMMAs were prepared by living anionic or group transfer polymerization (GTP), followed by bromination of the respective active site with Br₂ or N‐bromosuccinimide (NBS). The yield of the terminal bromination in the products of both living polymerizations was 60–64% at best, compared with the yield of the bromination of 1‐methoxy‐(1‐trimethylsilyloxy)prop‐1‐ene (a model of the GTP active site) with NBS, as found by ¹H‐NMR. The PMMA macroinitiators prepared were utilized to start the sequential ATRP, finally affording PMMA‐b‐PBuA‐b‐PSt (M_n 69,100), PMMA‐b‐PSt‐b‐PBuA (M_n 21,300) and PMMA‐b‐PSt‐b‐PMMA (M_n 35,200), which have not yet been synthesized by ATRP. After the second block has been formed, the Br‐unterminated part of PMMA macroinitiator was removed by extraction or repeated precipitation. In the third (last) sequence polymerization, induction periods were observed. The first two triblock copolymers were free of precursors and have M_w/M_n values 1.5–1.6 (SEC). In the course of the last step of PMMA‐b‐PSt‐b‐PMMA synthesis, the content of the PMMA‐b‐PSt precursor slowly decreased with increasing MMA conversion. Still, at ≈90% MMA conversion, about 10–15% of the precursor remained in the product. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 3514–3522, 2001     

Gas‐phase‐assisted surface polymerization of methyl methacrylate with Fe(0)/TsCl initiator system

To obtain a high polymer coated Fe(0) surface, gas‐phase‐assisted surface polymerization (GASP) of methyl methacrylate (MMA) was investigated using a zero‐valent iron (Fe(0))/p‐toluene sulfonylchloride (TsCl) initiator system, resulting in successful high polymer production on the solid surface. GASP was found to be initiated by radical species that might have been generated via redox reactions with Fe(0), Fe(II), Fe(III), and TsCl. From ¹H‐NMR analysis, the p‐toluene sulfonyl group was found at one end of the polymer chain. The molecular weight of obtained PMMA drastically decreased with increase in the composition ratio of Fe(0) in the initiator system, and increased with increase in polymer yield. From the results, it was assumed that the physically controlled polymerization of MMA proceeded by immobilized active species at gas–solid interfaces. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1879–1886, 2007     

A Novel Process for Ultrasound‐Induced Radical Polymerization in CO2‐Expanded Fluids

Summary: A strong viscosity increase upon polymerization hinders cavitation and subsequent radical formation during an ultrasound‐induced bulk polymerization. In this work, ultrasound‐induced radical polymerizations of methyl methacrylate (MMA) have been performed in CO₂‐expanded MMA in order to reduce the viscosity of the reaction mixture. For this purpose, the phase behavior of CO₂/MMA systems has been determined. With temperature oscillation calorimetry, the influence of CO₂ on the viscosity and on the reaction kinetics of ultrasound‐induced polymerizations of MMA has been studied. In contrast to polymerizations in bulk, this technique shows that a low viscosity is maintained during polymerization reactions in CO₂‐expanded MMA. As a consequence, a constant or even increasing polymerization rate is observed when pressurized CO₂ is applied. Moreover, the ultrasound‐induced polymer scission in CO₂‐expanded MMA is demonstrated, which appears to be a highly controlled process. Finally, a preliminary sustainable process design is presented for the production of 10 kg/h pure PMMA (specialty product) in CO₂‐expanded MMA by ultrasound‐induced initiation.

Process flow diagram of the ultrasound‐induced polymerization of MMA in CO₂‐expanded MMA.     

MesoDyn modeling study of the phase morphologies of miktoarm poly(ethylene oxide)‐b‐poly(methyl methacrylate) copolymers doped with nanoparticles

Earlier studies have shown that poly(ethylene oxide) (PEO) and poly(methyl methacrylate) (PMMA) blocks are compatible at 270 and 298 K, and that their Flory–Huggins interaction parameters have the same blending ratio dependence at both temperatures. At a much higher temperature (400 K), the behavior of PEO/PMMA blends is strikingly different as both components become incompatible, while the Flory–Huggins parameters are low. Here we investigate the effect of doping with nanoparticles on the degree of incompatibility of twelve miktoarm PEO‐b‐PMMA copolymers at 400 K. Since PEO tends to be semicrystalline and long chains aggregate easily, PEO‐rich and long‐chain copolymer blends feature the highest degree of incompatibility for all nanoparticle arrangements and present cubic phase morphologies. In addition, the largest nanoparticles can reinforce the microscopic phase separation of all PEO‐b‐PMMA copolymers. This shows that the main factor affecting the phase morphology is the size of the nanoparticles. Also, only the asymmetric Da3‐type PEO‐rich copolymers show a hexagonal cylindrical phase morphology, which illustrates the effect induced by the nanoparticles on the microscopic phase separation changes of the PEO‐b‐PMMA copolymers. These induced effects are also related to the composition and molecular architecture of the copolymers. © 2013 Society of Chemical Industry     

Preparation and characterization of a poly(methyl methacrylate) based composite bone cement containing poly(acrylate‐co‐silane) modified hydroxyapatite nanoparticles

The purpose of this study was to study the mechanical properties of poly(methyl methacrylate) (PMMA)‐based bone cement incorporated with hydroxyapatite (HA) nanoparticles after surface modification by poly(methyl methacrylate‐co‐γ‐methacryloxypropyl timethoxysilane) [P(MMA‐co‐MPS)]. PMMA and P(MMA‐co‐MPS) were synthesized via free‐radical polymerization. P(MMA‐co‐MPS)‐modified hydroxyapatite (m‐HA) was prepared via a dehydration process between silane and HA; the bone cement was then prepared via the in situ free‐radical polymerization of methyl methacrylate in the presence of PMMA and P(MMA‐co‐MPS)–m‐HA. Fourier transform infrared (FTIR) spectroscopy, ¹H‐NMR, and gel permeation chromatography were used to characterize the P(MMA‐co‐MPS). Thermogravimetric analysis and FTIR were used as quantitative analysis methods to measure the content of P(MMA‐co‐MPS) on the surface of HA. The effect of the proportion of m‐HA in the PMMA‐based bone cement on the mechanical properties was studied with a universal material testing machine. A 3‐(4,5‐dimethylthiazol‐2‐yl)‐2,5‐diphenyltetrazolium bromide assay was also carried out to determine the cytotoxicity of the composite bone cement. The results showed that the surface modification of HA greatly improved the interaction between the inorganic and organic interfaces; this enhanced the mechanical properties of bone cement for potential clinical applications. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40587.