Influence of additional thermal stabilizers on the reprocessing of postconsumer poly(vinyl chloride) bottles

The addition of heat stabilizers is essential for preventing the degradation of poly(vinyl chloride) (PVC) during its processing. The heat stabilizers consumed in the first run have to be made up before the reprocessing of recycled PVC. In this study, solvent‐cast films, which were prepared from granulated postconsumer PVC bottles mixed with plasticizers and thermal stabilizers, were used. The films were subjected to various heat treatments. No considerable structural change upon heat treatments at 140–160°C was found in IR and differential scanning calorimetry analyses. Polyene formation observed through ultraviolet analysis was not severe, indicating that the added stabilizers worked well in preventing degradation. The weight loss during the heat treatments was attributed partly to the decomposition of PVC and the evaporation of volatile components and mainly to the removal of the solvent upon heating. Although this study was conducted with water bottles that were to be recycled, it may be equally well applied to other similarly formulated PVC‐based materials, such as packaging films. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3994–3999, 2003     

Investigation of the thermal,mechanical and morphological properties of poly(vinyl chloride)/polyhedral oligomeric silsesquioxane nanocomposites

Research into organic–inorganic nanocomposites has recently become popular, particularly the development of new polymer nanocomposites. Compared to pristine polymers or conventional composites, these nanocomposites exhibit improved properties. The storage modulus of a poly(vinyl chloride) (PVC)/polyhedral oligomeric silsesquioxane (POSS) nanocomposite slightly decreased with POSS content, but had a higher modulus from 50 to 100 °C. Some of the material appeared to be aggregated with 1 wt% POSS in the polymeric matrix. Conversely, with a POSS content of 5 wt%, a better dispersion of the nanoparticles was observed. The presence of POSS in the plasticised PVC compound had little influence on the final properties of the nanocomposites, showing weaker interactions between the POSS and the plasticised PVC compound. Copyright © 2010 Society of Chemical Industry     

Effect of moisture content on mechanical properties,thermal and structural stability and extrudate texture of poly(vinyl chloride)/wood sawdust composites

Mechanical properties and thermal and structural changes of poly(vinyl chloride) (PVC)/wood sawdust composites were assessed with respect to the effect of moisture content, varying from 0.33 to 3.00 % by weight in the composite, for three different wood sawdust contents. The swell ratio and texture characteristics of the composite extrudates were also evaluated. Unique explanations were given to describe changes in the composite properties in terms of molecular interactions between PVC, cellulosic sawdust and moisture, such as dipole–dipole interactions, interfacial defects and bonding, fibre swelling, and moisture evaporation. The results suggest that at low moisture content the tensile modulus decreased and elongation at break of the composites increased with moisture content, the effect being reversed for high moisture content. Tensile strength decreased with increasing moisture content up to 1–2 %, and then unexpectedly increased at higher moisture contents. The effect of moisture content on flexural properties of the composite was similar to that on tensile properties. Impact strength of the composites was considerably improved with moisture content at low sawdust contents (16.7 wt%), and was independent of the moisture content at higher sawdust contents (28.6 and 37.5 wt%). A decrease in decomposition temperature with an increase in polyene content was evidenced with increasing moisture content, while the glass transition temperature did not change with varying moisture content. The extrudate swell ratio increased with the shear rate but remained unaffected by moisture content. The bubbling and peeling‐off in the composite extrudate occurred as a result of the evaporation of water molecules and the application of a high shear rate. Copyright © 2004 Society of Chemical Industry     

Effect of poly(epichlorohydrin) on the thermal and mechanical properties of poly(vinyl chloride)

Five kinds of polyepichlorohydrin (PECH) of different molecular weights were synthesized and characterized by gel permeation chromatography (GPC). Mechanical blending was used to mix PECH and poly(vinyl chloride) (PVC) together. The blends of different PVC/PECH ratios were characterized by thermogravimetric analysis (TGA), tensile tests, differential scanning calorimetry (DSC), and dynamic mechanical analysis (DMA). TGA results show the thermal stability of PVC/PECH blends is desirable. Tensile tests indicate elongation at break is raised by increasing both the amount and the molecular weight of PECH. DSC is used to determine the glass transition temperature of PECH, and a quite low T_g is obtained. DMA results indicate that PECH has a perfect compatibility with PVC, when PECH concentration is below 20 wt %. There is only one peak in each tan δ curve, and the corresponding T_g decreases as PECH amount increases. However, above 20 wt %, phase separation takes place. The molecular weight of PECH also has a great influence on the glass transition temperature of the blends. This study shows that PECH is an excellent plasticizer for PVC, and one can tailor the glass transition temperature and tensile properties by changing the amount and the molecular weight of PECH. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Hydrothermic aging of plasticized poly(vinyl chloride): Its effect on the dielectric,thermal, and mechanical properties

Accelerated hydrolytic aging (according to the NFT 5166 method) was performed on samples of poly(vinyl chloride) (PVC) plasticized with dioctylphthalate (DOP) and dinonyladipate (DNA) at different concentration ratios. The aging test consisted of immersing the samples in boiling water at 100°C. The samples were removed from water regularly, that is, every 2 h, for mechanical, thermal, and dielectric characterizations. Thermograms of PVC plasticized with DOP revealed no migration of the plasticizer independent of the concentration used. Moreover, the thermal stability of the samples was not affected by the hydrothermal aging. However, for PVC samples plasticized with DNA, a small amount of the plasticizer migrated from the polymer matrix with a considerable effect on the thermal stability. In fact, the data indicated a decrease in the decomposition temperature from 275 to 225°C, particularly for samples containing 50% (w/w) DNA immersed up to 10 h. The mechanical results showed that for a plasticizer content greater than 30% (w/w), the strain at break obtained for samples plasticized with DNA was lower than that for samples plasticized with DOP because the DNA molecules were more likely to be removed by water on account of their polarity and dimension. Finally, the dielectric measurements showed that the permittivity of all the PVC samples plasticized with DOP and immersed in boiling water was higher than that of the virgin samples. On the contrary, the permittivity of the aged unplasticized PVC was less than that of the nonimmersed samples. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3447–3457, 2003     

Evaluation of the effects of biobased plasticizers on the thermal and mechanical properties of poly(vinyl chloride)

Blends were prepared of poly(vinyl chloride) (PVC) with four different plasticizers; esters of aconitic, citric, and phthalic acids; and other ingredients used in commercial flexible PVC products. The thermal and mechanical properties of the fresh products and of the products after 6 months of aging were measured. Young's modulus of the PVC blends was reduced about 10‐fold by an increase in the plasticizer level from 15 to 30 phr from the semirigid to the flexible range according to the ASTM classification, but a 40‐phr level was required for PVC to retain its flexibility beyond 6 months. At the 40‐phr level, tributyl aconitate performed better than diisononyl phthalate (DINP) or tributyl citrate, in terms of lowering Young's modulus, both in the fresh materials and those aged for 6 months. The effects of the four plasticizers on the glass‐transition temperature (T_g) were similar, with T_g close to ambient temperature at the 30‐ and 40‐phr levels in freshly prepared samples and at 40–60°C in those aged for 6 months. The thermal stability of the PVC plasticized with DINP was superior among the group. Overall, tributyl aconitate appeared to be a good candidate for use in consumer products where the alleged toxicity of DINP may be an issue. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1366–1373, 2006     

Nanocomposites of poly(vinyl chloride) and nanometric calcium carbonate particles: Effects of chlorinated polyethylene on mechanical properties,morphology, and rheology

Nanocomposites of poly(vinyl chloride) (PVC) and nano‐calcium carbonate (CaCO₃) particles were prepared via melt blending, and chlorinated polyethylene (CPE) as an interfacial modifier was also introduced into the nanocomposites through preparing CPE/nano‐CaCO₃ master batch. The mechanical properties, morphology, and rheology were studied. A moderate toughening effect was observed for PVC/nano‐CaCO₃ binary nanocomposites. The elongation at break and Young's modulus also increased with increasing the nano‐CaCO₃ concentration. Transmission electron microscopy (TEM) study demonstrated that the nano‐CaCO₃ particles were dispersed in a PVC matrix uniformly, and a few nanoparticles agglomeration was found. The toughening effect of the nano‐CaCO₃ particles on PVC could be attributed to the cavitation of the matrix, which consumed tremendous fracture energy. The notched Izod impact strength achieved a significant improvement by incorporating CPE into the nanocomposites, and obtained the high value of 745 J/m. Morphology investigation indicated that the nano‐CaCO₃ particles in the PVC matrix was encapsulated with a CPE layer through preparing the CPE/nano‐CaCO₃ master batch. The evaluation of rheological properties revealed that the introduction of nano‐CaCO₃ particles into PVC resulted in a remarkable increase in the melt viscosity. However, the viscosity decreased with addition of CPE, especially at high shear rates; thus, the processability of the ternary nanocomposites was improved. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2714–2723, 2004     

Chemical recycling of poly(vinyl chloride): Application of partially dehydrochlorinated poly(vinyl chloride) for producing a chemically modified polymer

Poly(vinyl chloride) (PVC) pipes were chemically modified to produce a sulfonated polymer with dehydrochlorinated PVC samples as intermediates. Two intermediates were formed: (1) partially dehydrochlorinated PVC with long sequences of conjugated double bonds and (2) the product of the partial dehydrochlorination of PVC and the nucleophilic substitution of chlorine by hydroxyl groups. The IR spectra showed that the dehydrochlorinated samples were heterogeneous materials, showing different proportions of elimination products, hydroxyl substitution, and partial oxidation. Samples dehydrochlorinated with poly(ethylene glycol) with a molecular weight of 400 g/mol for 24 h and 15 min showed the highest sulfonation yield, which was related to the sulfonation mechanism occurring predominantly because of the presence of hydroxyl groups in a mixture of vinyl alcohol and vinyl chloride units. The sulfonation was confirmed by the presence of a medium‐intensity band at 1180 cm^?1, assigned to sulfonic groups. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effect of silane treated fly ash on physico-mechanical,morphological, and thermal properties of recycled poly(vinyl chloride) composites

The silane treatment on properties of fly ash (FA) and development of its composite using recycled poly(vinyl chloride) (r-PVC) material retrieve from waste wires and cable insulation are investigated in this work. The use of (3-aminopropyl)triethoxysilane was employed as a coupling agent with some other essential additives. The composites sheet was prepared by means of the melt mixing process and go along with the compression molding process. The superior properties on compatibility between silane-modified FA (FA(Si)) and r-PVC were successfully studied using rheological, thermomechanical, morphological, and water absorption analysis. Primary analysis of r-PVC and FA was employed using Fourier transform infrared spectroscopy analysis. The thermal stability of composites was stable up to 187°C. In addition, significant enhancement on tensile strength as well as young's modulus of composite as compared to untreated r-PVC/FA composites. Morphological properties of silane treated FA based composites presented the good distribution and excellent uniformity with higher wettability of FA particles within r-PVC matrix. The water absorption test showed decrease in water absorption with increase silane treatment concentration FA in the r-PVC matrix. It was remarkable to note that silane treated FA can be prepared as a composite using r-PVC matrix with further modified properties.     

Effect of plasticizers on mechanical,electrical, permanence,and thermal properties of poly(vinyl chloride)

Effects of three different plasticizers and their blends with dioctyl phthalate (DOP) on thermal stability, flammability, mechanical, electrical, and permanence properties of poly(vinyl chloride) (PVC) compound were studied. Various plasticizers used were DOP, butyl benzyl phthalate (BBP), isodecyl diphenyl phosphate (IDDP), and polybutylene adipate (PBA) at concentrations of up to 40 phr level. Studies showed that processability and softness were improved by addition of BBP. An increase in the content of IDDP increased the electrical and flammability properties, whereas compositions with PBA exhibited the best permanence properties. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3278–3284, 2003     

Studies on mechanical and rheological properties of poly(vinyl chloride) modified with elastomers and rigid organic particles

Chlorinated polypropylene (CPP) as rigid organic particles and chlorinated polyethylene (CPE) as elastomer were used to modify the properties of poly(vinyl chloride) (PVC) by melt blending. Both mechanical and rheological properties of the PVC blends were investigated. The submicroscopic morphology of the blends was observed by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results demonstrate that when the weight ratio of CPE to CPP is about 6 : 1, a sample with the best impact strength and without obvious decline in tensile strength can be obtained. The impact strength correlates well with SEM morphologies, and TEM micrographs in the necking of the tensile specimen indicate that a cold‐drawing deformation of rigid particles happens as reported by T. Kurauchi and T. Ohta (J Mater Sci 1984, 19, 1699). Therefore, a conclusion can be drawn that CPP particles acting similar to elastic particles can toughen PVC, and the cold‐drawing deformation is the primary reason for toughening the PVC blends. In addition, the addition of CPP can promote the processibility of PVC ternary blends. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2478–2483, 2003     

Study on thermal,mechanical and morphological properties of recycled poly(vinyl chloride)/fly ash composites

The present study deals with the development of composite materials utilizing recycled poly(vinyl chloride) (r‐PVC) recovered from waste electrical and electronic materials and waste fly ash obtained from thermal power plants. The effect of the incorporation of fly ash on the mechanical, thermal and morphological properties of the r‐PVC matrix was studied. The primary characterization of r‐PVC and fly ash was done employing FTIR, EDX, particle size analysis and XRD analysis. Subsequently, fly ash with a particle size of approximately 9.29 μm was incorporated within the r‐PVC matrix. Composite sheets were prepared using a melt blending process followed by compression moulding. The mechanical test revealed an increase in the tensile strength and elongation at break of the r‐PVC/fly ash composite up to 30 wt% loading of fly ash beyond which there was a decrease in the tensile strength. The impact strength, however, decreased with increasing fly ash content in the r‐PVC matrix. The morphological properties of the composites showed a good distribution of the filler within the recycled matrix. The thermal properties of r‐PVC also improved with the incorporation of fly ash which was revealed from DSC and TGA studies. The water absorption test showed an increase in water uptake with the addition of fly ash in the r‐PVC matrix. © 2020 Society of Chemical Industry     

Blends of plasticized poly(vinyl chloride) and waste flexible poly(vinyl chloride) with waste nitrile rubber powder

Blends of poly(vinyl chloride) (PVC) with varying contents of plasticizer and finely ground powder of waste nitrile rubber rollers were prepared over a wide range of rubber contents through high‐temperature blending. The effects of rubber and plasticizer (dioctyl phthalate) content on the tensile strength, percentage elongation, impact properties, hardness, abrasion resistance, flexural crack resistance, limiting oxygen index (LOI), electrical properties, and breakdown voltage were studied. The percentage elongation, flexural crack resistance, and impact strength of blends increased considerably over those of PVC. The waste rubber had a plasticizing effect. Blends of waste plasticized PVC and waste nitrile rubber showed promising properties. The electrical properties and LOI decreased with increasing rubber and plasticizer content. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1552–1558, 2004     

Rheology of poly(vinyl chloride) plastisol for superhigh shear‐rate processing. I

In coating operations with poly(vinyl chloride) plastisol, there is a high shear limit because the flow becomes unstable. However, there is an indication that the flow becomes stable at superhigh shear rates well past the unstable region. This article explores the effect of the particle size (with a similar size distribution spread) and the effect of the amount of the emulsifier on the flow at superhigh shear rates. It has been known that below the flow instability, larger particles lead to a lower viscosity, and an increased amount of the emulsifier leads to a higher viscosity. The question is whether or not the same trends persist at superhigh shear rates. Observations in this study confirm these trends. In addition, the emulsifier has been found to enhance the interparticle attraction. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Tensile properties of a poly(vinyl chloride) composite filled with poly(methyl methacrylate) grafted to oil palm empty fruit bunches

The influence of oil palm empty fruit bunch (OPEFB) fiber and oil palm empty fruit bunches grafted with poly(methyl methacrylate) (OPEFB‐g‐PMMA) on the tensile properties of poly(vinyl chloride) (PVC) was investigated. The OPEFB‐g‐PMMA fiber was first prepared with the optimum conditions for the grafting reaction, which were determined in our previous study. To produce composites, the PVC resin, OPEFB‐g‐PMMA fiber or ungrafted OPEFB fiber, and other additives were first dry‐blended with a laboratory blender before being milled into sheets on a two‐roll mill. Test specimens were then hot‐pressed, and then the tensile properties were determined. A comparison with the composite filled with the ungrafted OPEFB fiber showed that the tensile strength and elongation at break increased, whereas Young's modulus decreased, with the incorporation of 20 phr OPEFB‐g‐PMMA fiber into the PVC matrix. The trend of the tensile properties obtained in this study was supported by functional group analysis, glass‐transition temperature measurements, and surface morphological analysis. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Soiling of plasticized poly(vinyl chloride)

The effects of three plasticizers and two plasticizer concentrations on the topography and soiling of poly (vinyl chloride) (PVC) were studied. Palmitic acid and triolein were chosen to represent solid and liquid soils. The feasibility of using infrared spectroscopy to quantify the amount of soil on PVC was examined. The structure of the solid model soil on plasticized PVC was studied with optical microscopy and atomic force microscopy. Palmitic acid formed two different structures on the PVC surface. Both the type and concentration of the plasticizer influenced the structure of the oily soil on plasticized PVC. The wetting of plasticized PVC with the liquid oily soil was compared to wetting with water through the measurement of the contact angles. Plasticized PVC was hydrophobic and oleophilic. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Effect of hydrotalcite on the thermal stability,mechanical properties,rheology and flame retardance of poly(vinyl chloride)

Compounds of poly(vinyl chloride) (PVC) and hydrotalcite were prepared via melt blending, and the thermal stability, mechanical properties, rheology and flame retardance were studied. Transmission electron microscopy showed that the hydrotalcite achieved an optimal dispersion in PVC compounds when surface‐treated with titanate coupling agent. The Congo Red test and thermogravimetric analysis demonstrated that the thermal stability of PVC was improved significantly only in the presence of a complex of the hydrotalcite and the organotin stabilizer. Such a significantly positive thermal stabilizing effect was attributable to the stabilizing mechanisms that the electrostatic interaction generated between the electron cloud of chlorine atoms in PVC chain and the positive lay charge of hydrotalcite, which resulted in a decrease in electronic cloud density of chlorine atoms. This weakened the activity of chloride atoms, and restricted the initiation of the dehydrochlorination. A surface treatment for the hydrotalcite with the titanate coupling agent could reduce deterioration of the mechanical and rheological properties of the PVC at low concentration of hydrotalcite. The hydrotalcite also enabled useful application of PVC as a flame retardant as well as a smoke retarder in the light of a LOI value of more than 28.7 and UL 94 V‐0 grade at a PVC/hydrotalcite weight ratio of 70/30. Copyright © 2004 Society of Chemical Industry     

Preparation and structural characterization of nanocrystalline poly(vinyl chloride)

This article describes the development of novel nanocrystalline poly(vinyl chloride) (PVC) for potential applications in PVC processes and reports improvements in the mechanical properties and thermal resistance. Before the preparation of nanocrystalline PVC via jet milling, PVC was spray‐treated and heat‐treated to improve its crystallinity. The pulverization and degradation, morphology, crystalline structure, and melting‐point changes of postmodified PVC during jet milling and the relationship between the distributions of the particle size and processing temperature were investigated. X‐ray analysis and density testing indicated increased density and improved crystallinity. The crystalline region of nanocrystalline PVC was less than 80 nm, with a particle size distribution of 5–20 μm and a melting point of less than 128°C. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 563–569, 2004     

Structural changes and mechanical performance of recycled poly(vinyl chloride) bottles exposed to ultraviolet light at 313 nm

The structural changes and mechanical performance of virgin poly(vinyl chloride) (PVC) bottle (VB) compounds blended with postconsumer PVC bottles collected from a specified factory (RB‐F) and houses (RB‐H), were examined before and after UV irradiation at 313‐nm UV wavelength for different periods of time up to 28 days. The results indicated that, when exposed to UV light, the RB‐F/VB blends containing greater conjugated double bonds with higher yellowness index appeared to exhibit better mechanical performance than that of the RB‐H/VB blends. It was found that the amount of conjugated double bonds was not a linear function of the discoloration level of PVC compounds. Tensile strength of the VB compounds was not affected when incorporated with RB‐F recyclate, but progressively decreased with increasing RB‐H recyclate. An optimum concentration for RB recyclates to be added into the virgin compound was recommended for obtaining a maximum impact strength. Both tensile and impact strengths decreased with increasing UV exposure time, a severe degradation being obvious after a UV exposure time of 21 days. Hardness was not affected significantly by the addition of PVC recyclate, but increased with increasing UV exposure time. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 84–94, 2004     

Rheological behavior and thermal properties of poly(butyl acrylate‐co‐2‐ethylhexyl acrylate)‐grafted vinyl chloride resin

The rheological behavior and thermal properties of a poly(butyl acrylate‐co‐2‐ethylhexyl acrylate) [P(BA‐EHA)]‐grafted vinyl chloride (VC) composite resin [P(BA‐EHA)/poly(vinyl chloride) (PVC)] and its materials were investigated. The rheological behavior, thermal stability, and Vicat softening temperature (VST) of P(BA‐EHA)/PVC were measured with capillary rheometry, thermal analysis, and VST testing, respectively. The effects of the P(BA‐EHA) content and the polymerization temperature of grafted VC on the rheological behavior of the composite resin were examined. The weight loss of the composite resin and its extracted remainder via heating were analyzed. The influence of the content and crosslinking degree of P(BA‐EHA) and the polymerization temperature of the grafted VC on VST of the materials was determined. The results indicated the pseudoplastic‐flow nature of the composite resin. The flow property of the modified PVC resin was improved because of the incorporation of the acrylate polymer. The molecular weight of PVC greatly influenced the flow behavior and VST of the composite resin and its materials. The flowability of the composite resin markedly increased, and the VST of its materials decreased as the polymerization temperature of the grafted VC increased. The initial degradation temperature of the composite resin increased as the P(BA‐EHA) content increased. The VST of the samples was enhanced a little as the content of the crosslinking agent increased in P(BA‐EHA). As expected, the composite resin, with good impact resistance, had better heating stability and flowability than pure PVC, whereas the VST of the material decreased little with increasing P(BA‐EHA) content. Therefore, P(BA‐EHA)/PVC resins prepared by seeded emulsion polymerization have excellent potential for widespread applications. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 419–426, 2005