Effect of organic modifiers and silicate type on filler dispersion,thermal, and mechanical properties of ABS‐clay nanocomposites

Acrylonitrile–butadiene–styrene (ABS)–clay composite and intercalated nanocomposites were prepared by melt processing, using Na‐montmorillonite (MMT), several chemically different organically modified MMT (OMMT) and Na‐laponite clays. The polymer–clay hybrids were characterized by WAXD, TEM, DSC, TGA, tensile, and impact tests. Intercalated nanocomposites are formed with organoclays, a composite is obtained with unmodified MMT, and the nanocomposite based on synthetic laponite is almost exfoliated. An unintercalated nanocomposite is formed by one of the organically modified clays, with similar overall stack dispersion as compared to the intercalated nanocomposites. T_g of ABS is unaffected by incorporation of the silicate filler in its matrix upto 4 wt % loading for different aspect ratios and organic modifications. A significant improvement in the onset of thermal decomposition (40–44°C at 4 wt % organoclay) is seen. The Young's modulus shows improvement, the elongation‐at‐break shows reduction, and the tensile strength shows improvement. Notched and unnotched impact strength of the intercalated MMT nanocomposites is lower as compared to that of ABS matrix. However, laponite and overexchanged organomontmorillonite clay lead to improvement in ductility. For the MMT clays, the Young's modulus (E) correlates with the intercalation change in organoclay interlayer separation (Δd₀₀₁) as influenced by the chemistry of the modifier. Although ABS‐laponite composites are exfoliated, the intercalated OMMT‐based nanocomposites show greater improvement in modulus. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Poly(vinyl alcohol) nanocomposites with different clays: Pristine clays and organoclays

Poly(vinyl alcohol) (PVA)/clay nanocomposites were synthesized using the solution intercalation method. Na ion‐exchanged clays [Na⁺–saponite (SPT) and Na⁺–montmorillonite (MMT)] and alkyl ammonium ion‐exchanged clays (C₁₂–MMT and C₁₂OOH–MMT) were used for the PVA nanocomposites. From the morphological studies, the Na ion‐exchanged clay is more easily dispersed in a PVA matrix than is the alkyl ammonium ion‐exchanged clay. Attempts were also made to improve both the thermal stabilities and the tensile properties of PVA/clay nanocomposite films, and it was found that the addition of only a small amount of clay was sufficient for that purpose. Both the ultimate tensile strength and the initial modulus for the nanocomposites increased gradually with clay loading up to 8 wt %. In C₁₂OOH–MMT, the maximum enhancement of the ultimate tensile strength and the initial modulus for the nanocomposites was observed for blends containing 6 wt % organoclay. Na ion‐exchanged clays have higher tensile strengths than those of organic alkyl‐exchanged clays in PVA nanocomposites films. On the other hand, organic alkyl‐exchanged clays have initial moduli that are better than those of Na ion‐exchanged clays. Overall, the content of clay particles in the polymer matrix affect both the thermal stability and the tensile properties of the polymer/clay nanocomposites. However, a change in thermal stability with clay was not significant. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3208–3214, 2003     

Synthesis and characterization of poly(methyl methacrylate)/montmorillonite nanocomposites by in situ bulk polymerization

Poly(methyl methacrylate)/montmorillonite (MMT) nanocomposites were prepared by in situ bulk polymerization. The results showed that the silicone coupling agent affected the structure and properties of hybrid materials. XRD analysis showed that the dispersion of clay in nanocomposites with silicone‐modified organophilic MMT was more ordered than that in nanocomposites with unmodified organophilic MMT. The glass transition temperature (T_g) of the nanocomposites was 6–15°C higher and the thermal decomposition temperature (T_d) was 100–120°C higher than those of pure PMMA. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2256–2260, 2003     

Nanofibrillated cellulose,poly(vinyl alcohol), montmorillonite clay hybrid nanocomposites with superior barrier and thermomechanical properties

Nanocomposites of poly(vinyl alcohol) (PVA), nanofibrillated cellulose (NFC), and montmorillonite (MMT) clay were prepared via solvent casting. In addition to investigating the effect of clay loading, PVA matrices crosslinked with poly(acrylic acid) (PAA) were prepared and compared with linear (noncrosslinked) PVA nanocomposites. ¹³C NMR and infrared spectroscopy confirmed the presence of crosslinks. Scanning electron microscopy revealed effective NFC and MMT clay dispersion throughout the nanocomposites, while X‐ray diffraction highlighted the effectiveness of PAA to encourage clay dispersion. MMT clay provided a barrier against the diffusion of water and oxygen (molecules) through the nanocomposite films. Permeability and adsorption were further reduced by crosslinking, while oxygen barrier properties were remarkably enhanced at elevated relative humidities. Thermal stability of the PVA segments was strengthened by the presence of MMT clay and crosslinks. MMT clay–reinforced PVA and NFC within the films, increasing the Young's modulus, tensile strength, and glass transition temperature. Crosslinking further enhanced the thermomechanical properties by imparting physical restraints on polymer chain segments, providing elasticity, and ductility. The hybrid films were successfully reinforced at elevated humidities, with nanocomposites displaying enhanced storage moduli and near‐complete recovery. POLYM. COMPOS., 35:1117–1131, 2014. © 2013 Society of Plastics Engineers     

Influence of clay and predispersion method on the structure and properties of polystyrene (PS)‐clay nanocomposites

To prepare the polystyrene (PS)‐clay nanocomposites via an in situ emulsion polymerization, a clay predispersion method, i.e. dispersing the organic clay in the emulsifier solution by the assistance of ultrasonic, was proposed in this study. The conventional method, predispersing the organic clay into the monomer, was also presented for the comparison. The morphology analysis based on the X‐ray Deflection (XRD) and Transmission Electronic Microscopy (TEM) results suggested that the more uniform clay dispersion in the final nanocomposites could be achieved through the new method. The inorganic clay (Na‐MMT) and two organic clays (C₁₈‐MMT and VC₁₈‐MMT) synthesized by exchanging inorganic cations with the trimethyloctadecyl ammonium chloride (OTAC) and the vinylbenzyldimethyloctadecyl ammoniun chloride (VOAC) were chosen to investigate the influence of the clay surface modification on the properties of nanocomposites. The Dynamic Mechanical Analysis (DMA) results showed the storage modulus G′s of the nanocomposites had different enhancements over that of the pure PS, especially when the temperature approached the glass transition temperature (T_g). The T_gs of the nanocomposites, however, varied with the microstructure and the interactions between the polymer and the clay layers. The Na‐MMT and VC₁₈‐MMT increased the T_g, while the T_gs of PS/C₁₈‐MMT nanocomposites were slightly lower than that of the pure PS. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Synthesis and antimicrobial activity of biocidal polymer–montmorillonite nanocomposites

The bioactive agents p‐hydroxymethylbenzoate, 2,4‐dihydroxymethylbenzoate and methylsalicylate were reacted with polyoxyalkylene (D_230–2000)–montmorillonite (MMT) intercalated nanocomposites. D_230–2000–MMT were prepared by an ion exchange process of Na‐MMT and? NH₃⁺ groups in polyoxyalkylene amine hydrochloride of three different molecular masses (D₂₃₀, D₄₀₀ and D₂₀₀₀). The results of X‐ray analysis and transmission electron microscopy show that D₂₀₀₀–MMT/p‐hydroxymethylbenzoate is an exfoliated nanocomposite, whereas in D₂₃₀–MMT/p‐hydroxymethylbenzoate, D₂₃₀–MMT/2,4‐dihydroxymethylbenzoate, D₂₃₀–MMT/methylsalicylate and D₄₀₀–MMT/p‐hydroxymethylbenzoate, having lower molecular mass and polymer loading, the MMT rearranges in an intercalated and flocculated structure. The amount of intercalated polymer and interaction between polymer and layered silicate were determined using thermogravimetric analysis and Infrared spectroscopy. The antimicrobial activities of the nanocomposites were qualitatively and quantitatively assessed by agar diffusion tests and minimal inhibitory concentration values against a Gram‐negative bacterium (Escherichia coli NCIM 2065), a Gram‐positive bacterium (Bacillus subtilis ATCC) and fungi (Candida albicans SC5314 and Cryptococcus neoformans). The D₂₀₀₀–MMT/p‐hydroxymethylbenzoate nanocomposite strongly inhibits the growth of all the micro‐organisms tested. The diameter of the inhibition zone varies according to the type of micro‐organism tested. The effect of nanocomposite concentration on morphology, respiration and release of calcium, potassium and sodium ions of the test micro‐organisms was examined. Copyright © 2011 Society of Chemical Industry     

Preparation and properties of montmorillonite‐based polyimide nanocomposites

Montmorillonite (MMT)‐based polyimide (PI) nanocomposites were prepared via two‐stage polymerization of PI using polyamic acid (PAA). The clay was organically modified using various alkylammonium ions to examine the effect of changes in alkyl length on the intercalation spacing of both the treated clays and their hybrids with PAA and PI. The intercalation behavior of clay in the PI matrix and its thermal and mechanical properties were investigated as a function of clay concentration. The d‐spacing of organically modified MMT (O‐MMT) increased with increasing length of the alkylammonium chain. PI/O‐MMT hybrids form exfoliated nanocomposites at clay concentrations below 2 wt%, while they form intercalated nanocomposites together with some exfoliated ones at clay contents exceeding 4 wt%. Young's modulus increased rapidly to a clay loading of 2 wt%, and leveled off with further increases in clay loading. The tensile strength at break increased rapidly up to a clay loading of 1 wt%, and then decreased sharply, while the strain at break showed a monotonic decrease with increasing clay loading from 0 to 8 wt%. The storage modulus, E′, in the temperature range below the glass transition temperature T_g, generally increased with increasing clay content, except at the highest clay content of 8 wt%. Copyright © 2004 Society of Chemical Industry     

Structural characterization of hydrophilic polymer blends/montmorillonite clay nanocomposites

The nanocomposite films comprising polymer blends of poly(vinyl alcohol) (PVA), poly(vinyl pyrrolidone) (PVP), poly(ethylene oxide) (PEO), and poly(ethylene glycol) (PEG) with montmorillonite (MMT) clay as nanofiller were prepared by aqueous solution casting method. The X‐ray diffraction studies of the PVA–x wt % MMT, (PVA–PVP)–x wt % MMT, (PVA–PEO)–x wt % MMT and (PVA–PEG)–x wt % MMT nanocomposites containing MMT concentrations x = 1, 2, 3, 5 and 10 wt % of the polymer weight were carried out in the angular range (2θ) of 3.8–30°. The values of MMT basal spacing d₀₀₁, expansion of clay gallery width W_cg, d‐spacing of polymer spherulite, crystallite size L and diffraction peak intensity I were determined for these nanocomposites. The values of structural parameters reveal that the linear chain PEO and PEG in the PVA blend based nanocomposites promote the amount of MMT intercalated structures, and these structures are found relatively higher for the (PVA–PEO)–x wt % MMT nanocomposites. It is observed that the presence of bulky ester‐side group in PVP backbone restricts its intercalation, whereas the adsorption behavior of PVP on the MMT nanosheets mainly results the MMT exfoliated structures in the (PVA–PVP)–x wt % MMT nanocomposites. The crystallinities of the PEO and PEG were found low due to their blending with PVA, which further decreased anomalously with the increase of MMT concentration in the nanocomposites. The decrease of polymer crystalline phase of these materials confirmed their suitability in preparation of novel solid polymer nanocomposite electrolytes. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40617.     

Rheology of poly(propylene)/clay nanocomposites

The linear and nonlinear shear rheological behaviors of poly(propylene) (PP)/clay (organophilic‐montmorillonite) nanocomposites (PP/org‐MMT) were investigated by an ARES rheometer. The materials were prepared by melt intercalation with maleic anhydride functionalized PP as a compatibilizer. The storage moduli (G′), loss moduli (G″), and dynamic viscosities of polymer/clay nanocomposites (PPCNs) increase monotonically with org‐MMT content. The presence of org‐MMT leads to pseudo‐solid‐like behaviors and slower relaxation behaviors of PPCN melts. For all samples, the dependence of G′ and G″ on ω shows nonterminal behaviors. At lower frequency, the steady shear viscosities of PPCNs increase with org‐MMT content. However, the PPCN melts show a greater shear thinning tendency than pure PP melt because of the preferential orientation of the MMT layers. Therefore, PPCNs have higher moduli but better processibility compared with pure PP.© 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2427–2434,2004     

Intercalated clay structures and amorphous behavior of solution cast and melt pressed poly(ethylene oxide)–clay nanocomposites

The polymer nanocomposite (PNC) films consisted of poly(ethylene oxide) (PEO) and sodium cations montmorillonite (MMT) clay were prepared by aqueous solution casting and direct melt press compounding techniques, whereas the films of PEO with trimethyl octadecyl ammonium cations organo‐modified montmorillonite (OMMT) clay were formed by melt pressed technique. The clay concentrations in the nanocomposites used are 1, 2, 3, 5, 10, and 20 wt % of the PEO weight. The X‐ray diffraction patterns of these nanocomposites were measured in the angular range (2θ) of 3.8–30°. The values of basal spacing d₀₀₁ of MMT/OMMT, clay gallery width W_cg, d‐spacings of PEO crystal reflections d₁₂₀ and d₁₁₂, and their corresponding crystallite size L, and the peaks intensity I (counts) were determined for these nanocomposites. Results reveal that the nanocomposites have intercalated clay structures and the amount of intercalation increases with the increase of clay concentration. As compared to melt pressed PEO–MMT nanocomposites, the amount of clay intercalation is higher in aqueous solution cast nanocomposites. At 20 wt % MMT dispersion in PEO matrix, the solution cast PEO–MMT nanocomposite almost changes into amorphous phase. The melt press compounded PEO–OMMT films show more intercalation as compared to the PEO–MMT nanocomposites prepared by same technique. In melt pressed nanocomposites, the PEO crystalline phase significantly reduces when clay concentration exceeds 3 wt %, which is evidenced by the decrease in relative intensity of PEO principal crystalline peaks. The effect of interactions between the functional group (ethylene oxide) of PEO and layered sheets of clay on both the main crystalline peaks of PEO was separately analyzed using their XRD parameters in relation to structural conformations of these nanocomposites. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39898.     

Thermal aging and accelerated weathering of PVC/MMT nanocomposites: Structural and morphological studies

This work focuses on the influence of weathering factors—UV radiation, humidity, and temperature on the structure and morphology of poly(vinyl chloride)/montmorillonite (PVC/MMT) nanocomposites obtained by melt blending. It has been observed that organically modified MMT (OMMT) deteriorates the weathering resistance, the thermal behavior, as well as the long‐term stability of PVC. Decomposition of the organic modifier of MMT causes substantial color changes in the PVC nanocomposites as it facilitates the dehydrochlorination process of the polymer. However, the nonmodified MMT provides some stabilization during PVC weathering. The nanocomposites after annealing are characterized by higher glass transition temperature. The increase in heat capacity step (Δc_p) during glass transition suggests that in the PVC composites with nonmodified MMT stronger molecular interactions between the polymer and clay platelets occur than in PVC/OMMT nanocomposites. The scanning electron microscopy images on the surface and the cross section show that thermal aging and weathering proceed by different mechanisms. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42090.     

Study of the exfoliation process of epoxy–clay nanocomposites by different curing agents

Epoxy–clay nanocomposites were synthesized using two organoclays cured with different chemicals at different temperatures. Interlayer distance of the clay layers and curing process were investigated by X‐ray diffraction and infrared spectra. The clay treated with facilitated curing agent, 2,4,6‐tris[(dimethylamino)methyl]phenol, can exfoliate at all curing conditions, but for the other clay treated with low‐speed curing agent, p,p′‐diaminodiphenylmethane, exfoliation of the clay layers does not occur. It was found that the relative curing speed between the interlayer and extralayer was the most important factor determining clay exfoliation. Exfoliated epoxy–clay nanocomposites can be prepared if the curing speed of the interlayer is higher than that of the extralayer, irrespective of the curing agent and temperature used. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 511–517, 2003     

The effect of montmorillonite and compatibilizer quantities on stiffness and toughness of polyamide nanoblends

Although polymer blend nanocomposites are widely studied, the balance between stiffness and toughness has not yet been investigated in detail. Some materials producers as well as some sectors in the automotive industry try to improve the toughness of materials without an important loss in stiffness. With this in mind, the aim of the study reported here was to obtain a good balance between toughness and stiffness of polymer blends with different amounts of clay and compatibilizer. In this context, the microstructure of polyamide 6/ethylene–propylene–diene metallocene terpolymer/(ethylene–propylene–diene copolymer)‐graft‐(maleic anhydride) blends with various amounts of clay (2, 3, 4 and 5 wt%) and compatibilizer (10 and 20 wt%) was studied to analyse the achieved morphology to understand the macroscopic properties. The morphology of the rubber phase and the dispersion of the montmorillonite (MMT) are the main factors that influence the mechanical properties. In this sense, the highest Young's modulus is achieved for nanoblends with 5 wt% of MMT, although this nanoblend has the lowest value of notched Izod impact strength. The results obtained suggest that there is a clear trade‐off between stiffness, toughness and temperature behaviour when the ratio of (ethylene–propylene–diene copolymer)‐graft‐(maleic anhydride) to MMT is 5:1. Copyright © 2009 Society of Chemical Industry     

Synthesis and characterization of novel poly(o‐toluidine) montmorillonite nanocomposites: Effect of surfactant on intercalation

The investigation of clay based polymer nanocomposites has opened the door for the development of novel, ecofriendly advanced nano materials that can be safely recycled. Because of their nanometer size dispersion, these nanocomposites often have superior physical and mechanical properties. In this study, novel nanocomposites of poly(o‐toluidine) (POT) and organically modified montmorillonite (MMT) were synthesized using camphor sulfonic acid (CSA), cetyl pyridinum chloride (CPCl), and N‐cetyl‐N,N,N‐trimethyl ammonium bromide (CTAB) to study the role of surfactant modification on the intercalation. The in situ intercalative polymerization of POT within the organically modified MMT layers was analyzed by FTIR, UV–visible, XRD, SEM as well as TEM studies. The average particle size of the nanocomposites was found to be in the range 80–100 nm. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Electron beam synthesis and characterization of poly(vinyl alcohol)/montmorillonite nanocomposites

Poly(vinyl alcohol) (PVA)/montmorillonite clay (MMT) nanocomposites in the form of films were prepared under the effect of electron beam irradiation. The PVA/MMT nanocomposites gels were characterized by X‐ray diffraction (XRD), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and mechanical measurements. The study showed that the appropriate dose of electron beam irradiation to achieve homogeneous nanocomposites films and highest gel formation was 20 kGy. The introduction of MMT (up to 4 wt %) results in improvement in tensile strength, elongation at break, and thermal stability of the PVA matrix. In addition, the intercalation of PVA with the MMT clay leads to an impressive improved water resistance, indicating that the clay is well dispersed within the polymer matrix. Meanwhile, it was proved that the intercalation has no effect on the metal uptake capability of PVA as determined by a method based on the color measurements. XRD patterns and SEM micrographs suggest the coexistence of exfoliated intercalated MMT layers over the studied MMT contents. The DSC thermograms showed clearly that the intercalation of PVA polymer with these levels of MMT has no influence on the melting transitions; however, the glass transition temperature (T_g) for PVA was completely disappeared, even at low levels of MMT clay. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1129–1138, 2006     

Physical properties of poly(trimethylene terephthalate)/organoclay nanocomposites obtained via melt compounding and in situ polymerization

Two series of poly(trimethylene terephthalate) (PTT) nanocomposites, containing an organically modified montmorillonite (MMT) clay (1,2‐aminododecanoic acid (ADA)–intercalated MMT) were prepared via melt compounding and in situ polymerization methods using dimethyl terephthalate (DMT) and 1,3‐propanediol (PDO). The effect of different methods of preparation and varying organoclay contents (1−5 wt%) on the structural, morphological, thermal, and mechanical properties were investigated. The results of wide‐angle X‐ray diffraction (WAXD) and transmission electron microscope (TEM) suggested the possible existence of intercalation morphology between ADA‐MMT and the PTT matrix obtained from melt compounding, and mostly exfoliation state from in situ polymerization depending on the amount of organoclay. From DSC studies, in melt compounding case, the addition of ADA‐MMT in PTT increases melt‐crystallization (T_cm) peak temperature by 14−15°C irrespective of the clay content. However, the melting temperature (T_m) of pristine PTT remains unchanged with increasing clay content. In the case of in situ polymerization, the T_cm and T_m peaks are shifted towards lower temperature with increasing clay content. Dynamic mechanical thermal analysis (DMTA) studies on melt compounded samples revealed a marginal lowering of glass transition temperature (T_g) irrespective of clay content, and a noticeable decrease in T_g with increasing clay content for in situ polymerized samples. The PTT/ADA‐MMT nanocomposites via melt compounding showed higher initial modulus and yield stress, and lower strain at break compared with in situ polymerization with increasing clay content. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Synthesis and antimicrobial activity of the Schiff base from polyoxyalkylene‐montmorillonite nanocomposites and aldehydes

Vanillin (4‐hydroxy‐3‐methoxy benzaldehyde) and 5‐formylamino salicylic acid microbicides were reacted with polyoxyalkylene‐montmorillonite (D_230–2000‐MMT) nanocomposites. The microstructure of these Schiff base nanocomposites was characterized by TEM and XRD. D_230–2000‐MMT nanocomposites were prepared by an ion exchange process of sodium montmorillonite (Na‐MMT) and NH₃ ⁺ groups in polyoxyalkylene amine hydrochloride with three different molecular masses of D₂₃₀, D₄₀₀, and D₂₀₀₀. Wide‐angle X‐ray diffraction confirms the intercalation of the polymer between the silicate layers. Electrostatic interaction between the positively charged NH₃ ⁺ groups and the negatively charged surface of MMT was observed. The nanocomposites were tested for antimicrobial activity against the Gram‐negative bacteria (Escherichia coli NCIM 2065), Gram‐positive bacteria (Bacillus subtillus ATCC), and fungi (Candida albicans SC5314 and Cryptococcus neoformans). The D₂₀₀₀‐MMT/vanillin Schiff base nanocomposite strongly inhibited the growth of all microorganisms that can be used in different applications. The amount of loaded polymer and the structure of the nanocomposite play an important role in inhibiting the bacterial and fungal strains. It is found that the Schiff base nanocomposite affect the morphology, oxygen consumption, and the release of cytoplasmic constituents such as potassium (K⁺), sodium (Na⁺), and calcium (Ca²⁺) ions leading to death of the cells. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Preparation and characterization of anionically polymerized butadiene‐isoprene copolymer/clay nanocomposites

Butadiene‐isoprene copolymer/montmorillonite (BIR/MMT) nanocomposites were synthesized successfully via in situ anionic polymerization. The results of transmission electron microscopy and X‐ray diffractometer showed that the clay layers were exfoliated and high reaction temperature benefited the exfoliation of layers in BIR/MMT. The polymerization still exhibited “living” characteristics with the addition of organophilic montmorillonite (OMMT). However, the contents of 1,2‐polybutadiene and 3,4‐polyisoprene of the copolymer decreased with the addition of OMMT, because of its absorption effect on N,N,N′,N′‐tetramethylethanediamine as revealed by ¹H NMR. Moreover, it was observed that the glass‐transition temperature of the BIR/MMT nanocomposites also decreased when compared with the BIR copolymers. The thermal stability of the nanocomposites was improved, because of the barrier property of exfoliated clay layers. © 2006 Wiley Periodicals, Inc. J Appl PolymSci 102: 1167–1172, 2006     

Preparation and characteristics of nitrile rubber (NBR) nanocomposites based on organophilic layered clay

The effect of clay modification on organo‐montmorillonite/NBR nanocomposites has been studied. Organo‐montmorillonite/NBR nanocomposites were prepared through a melt intercalation process. NBR nanocomposites were characterized by X‐ray diffraction (XRD), transmission electron microscopy (TEM), dynamic mechanical thermal analysis (DMTA) and a universal testing machine (UTM). XRD showed that the basal spacing in the clay increased, which means that the NBR matrix was intercalated in the clay layer galleries. On TEM images, organo‐montmorillonite (MMT) particles were clearly observed, having been exfoliated into nanoscale layers of about 10–20 nm thickness from their original 40 µm particle size. These layers were uniformly dispersed in the NBR matrix. The DMTA test showed that for these nanocomposites the plateau modulus and glass transition temperature (T_g) increased with respect to the corresponding values of pure NBR (without clay). UTM test showed that the nanocomposites had superior mechanical properties, ie strength and modulus. These improved properties are due to the nanoscale effects and strong interactions between the NBR matrix and the clay interface. Copyright © 2003 Society of Chemical Industry     

Preparation and characterization of polyimide nanocomposites with different organo‐montmorillonites

Poly(amic acid) nanocomposites were synthesized from a dimethylacetamide (DMAc) solution with two organophilic montmorillonites (organo‐MMTs). It was then heated at various temperatures under vacuum, yielding 15–20 um thick films of polyimide/organo‐MMT hybrid with different clay contents (1–8 wt%). Dodecy‐lamine (C₁₂‐) and hexadecylamine (C₁₆‐) were used as aliphatic alkylamines in organo‐MMT. The ultimate strength monotonically increased with increasing clay content in the polymer matrix. Maximum enhancement in the initial modulus was observed for the blends containing 2 wt% clay with two kinds of organo‐clays, and values did not alter significantly with further increases in clay content. Additions of only 2 wt% C₁₂‐ and C₁₆‐MMT to the polyimide were shown to cause 94%‐95% reduction in oxygen gas permeability. This is caused by the barrier properties of the clay layers dispersed in the composite. In general, C₁₆‐MMT is more effective than C₁₂‐MMT in increasing both the tensile property and the gas barrier in a polyimide matrix. Intercalations of the polymer chains in clay were examined through wide‐angle X‐ray diffraction (XRD) and electron microscopies (SEM and TEM).