Syntheses and biodegradability of benzylated waste pulps and graft copolymers from PBzs and L‐lactic acid

Benzylated waste pulps (PBzs) were synthesized from treated waste pulp (Pulp), and benzyl chloride with phase transfer catalyst (PTC), and graft copolymers (PBz‐g‐LA) were synthesized from PBzs and L‐lactic acid (LA). Thermal properties, solubility, crystallinity, and biodegradability of the obtained PBzs and graft copolymers were investigated. PBzs with the degree of substitution (DS) higher than 1.5 showed T_g and T_m in DSC measurement. All PBz‐g‐LA exhibited no T_m. However, the graft copolymers obtained from lower DS PBzs having no T_g, exhibited T_g. The solubility of PBzs enhanced with increasing DS, and the crystallinity of PBzs reduced with increasing DS because of hydrophobicity and steric effect of benzyl groups. The solubility of graft copolymers was similar to that of original PBzs. Biodegradation tests for PBzs, Pulp, and graft copolymers were performed using cellulase in 0.1 M acetate buffer solution (pH 5.5) at 37°C. All samples showed biodegradability though the biodegradation rate decreased with increasing DS of PBz. In PBz‐g‐LA, the initial biodegradation rate was faster than that of original PBz because of hydrolysis of LA units. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2658–2664, 2004     

Investigation of the cellulose/LiCl/dimethylacetamide and cellulose/LiCl/N-methyl-2-pyrrolidinone solutions by 13C NMR spectroscopy

The cellulose/lithium chloride/dimethylacetamide (DMAc) and cellulose/lithium chloride/N-methyl-2-pyrroilidinone (NMP) solutions were investigated by ¹³C NMR spectroscopy. Well-resolved spectra were obtained for both solutions and indicated that cellulose was present in these systems in the form of underivatized cellulose. The change in ¹³C chemical shifts of DMAc and NMP in the presence of LiCl and LiBr was compared with that of several salt/aprotic solvents, and the results point to the existence of a cellulose–LiCl–DMAc (or NMP) complex in which the lithium cation is strongly bound to the amide carbonyl oxygen and the chloride anion involved in the dissociation of the cellulose hydrogen bonds. Spin–lattice relaxation times (T₁ of the ¹³C carbons of the solvent molecules, DMAc and NMP, show a large decrease in T¹ for all solvent carbons upon addition of LiCl. Further decrease in T₁ is observed when cellulose is introduced to the LiCl/NMP but not to the LiCl/DMAc systems. These observations are attributed to slower molecular motions of DMAc and NMP in the presence of LiCl, and, in the case of NMP, in the presence of cellulose.     

Synthesis functional poly(carbonate‐b‐ester) copolymers and micellar characterizations

Functional poly(carbonate‐b‐ester)s were synthesized in buck by ring‐opening polymerization of the carbonate (TMC, MBC, or BMC) with tert‐butyl N‐(2‐hydroxyethyl) carbamate as an initiator, and then with ε‐CL (or ε‐BCL) comonomer. Subsequently, the PMMC‐b‐PCL with pendent carboxyl groups and the PTMC‐b‐PHCL with pendent hydroxyl groups were obtained by catalytic debenzylation. DSC analysis indicated that only one T_g at an intermediate temperature the T_gs of the two polymer blocks. A decrease T_g was observed when an increase contents of ε‐CL incorporated into the copolymers. In contrast, two increased T_ms were observed with increasing PCL content. The block copolymers formed micelle in aqueous phase with critical micelle concentrations (cmcs) in the range of 2.23–14.6 mg/L and with the mean hydrodynamic diameters in the range of 100–280 nm, depending on the composition of copolymers. The drug entrapment efficiency and hydrolytic degradation behavior of micelle were also evaluated. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Grafting of poly(3‐hydroxyalkanoate) and linoleic acid onto chitosan

Poly(3‐hydroxy octanoate) (PHO), poly(3‐hydroxy butyrate‐co‐3‐hydroxyvalerate) (PHBV), and linoleic acid were grafted onto chitosan via condensation reactions between carboxylic acids and amine groups. Unreacted PHAs and linoleic acid were eliminated via chloroform extraction and for elimination of unreacted chitosan were used 2 wt % of HOAc solution. The pure chitosan graft copolymers were isolated and then characterized by FTIR, ¹³C‐NMR (in solid state), DSC, and TGA. Microbial polyester percentage grafted onto chitosan backbone was varying from 7 to 52 wt % as a function of molecular weight of PHAs, namely as a function of steric effect. Solubility tests were also performed. Graft copolymers were soluble, partially soluble or insoluble in 2 wt % of HOAc depending on the amount of free primary amine groups on chitosan backbone or degree of grafting percent. Thermal analysis of PHO‐g‐Chitosan graft copolymers indicated that the plastizer effect of PHO by means that they showed melting transitions T_ms at 80, 100, and 113°C or a broad T_ms between 60.5–124.5°C and 75–125°C while pure chitosan showed a sharp T_m at 123°C. In comparison of the solubility and thermal properties of graft copolymers, linoleic acid derivatives of chitosan were used. Thus, the grafting of poly(3‐hydroxyalkanoate) and linoleic acid onto chitosan decrease the thermal stability of chitosan backbone. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103:81–89, 2007     

Preparation and flocculation behavior of cellulose‐g‐PMOTAC copolymer

As a contribution to the wider use of biodegradable materials, this article reports the synthesis and testing of cationic polyelectrolyte cellulose derivatives for use as flocculation chemicals. Cellulose macroinitiator is synthesized in DMAc/LiCl solvent system by direct acylation of cellulose with 2‐bromoisobutyryl bromide. Cellulose‐graft‐poly(N,N‐dimethyl aminoethyl methacrylate) (cellulose‐g‐PDMAEMA) copolymers are prepared by copper‐mediated radical polymerization in homogeneous medium. Formation of the macroinitiator and graft copolymers is confirmed by ATR‐FTIR and ¹H NMR. Quaternization of the graft chains to poly(methacryloxyethyl trimethylammonium chloride) (PMOTAC) produces cellulose‐g‐PMOTAC, which performs similarly to a commercial product in flocculation of pulp and kaolin. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40448.     

Synthesis and characterization of degradable copoly(trans‐4‐hydroxy‐L‐proline/ϵ‐caprolactone)

The melt polycondensation reaction of N‐protected trans‐4‐hydroxy‐L ‐proline (N‐Z‐Hpr) and ?‐caprolactone (?‐CL) over a wide range of molar fractions in the feed produced new and degradable poly(N‐Z‐Hpr‐co‐?‐CL)s with stannous octoate as a catalyst. The optimal reaction conditions for the synthesis of the copolymers were obtained with 1.5 wt % stannous octoate at 140°C for 24 h. The synthesized copolymers were characterized by IR spectrophotometry, ¹H NMR, differential scanning calorimetry, and Ubbelohde viscometry. The values of the inherent viscosity (η_inh) and glass‐transition temperature (T_g) of the copolymers depended on the molar fractions of N‐Z‐Hpr. With an increase in the trans‐4‐hydroxy‐N‐benzyloxycarbonyl‐L ‐proline (N‐CBz‐Hpr) feed from 10 to 90 mol %, a decrease in η_inh from 2.47 to 1.05 dL/g, and an increase in T_g from ?48 to 49°C were observed. The in vitro degradation of these poly(N‐CBz‐Hpr‐co‐?‐CL)s was evaluated from weight‐loss measurements. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 3176–3182, 2003     

Synthesis and characterization of poly(ether amide ether ketone)/poly(ether ketone ketone) copolymers

A new monomer, N,N′‐bis(4‐phenoxybenzoyl)‐m‐phenylenediamine (BPPD), was prepared by condensation of m‐phenylenediamine with 4‐phenoxybenzoyl chloride in N,N‐dimethylacetamide (DMAc). A series of novel poly(ether amide ether ketone) (PEAEK)/poly(ether ketone ketone) (PEKK) copolymers were synthesized by the electrophilic Friedel‐Crafts solution copolycondensation of terephthaloyl chloride (TPC) with a mixture of diphenyl ether (DPE) and BPPD, over a wide range of DPE/BPPD molar ratios, in the presence of anhydrous AlCl₃ and N‐methylpyrrolidone (NMP) in 1,2‐dichloroethane (DCE). The influence of reaction conditions on the preparation of copolymers was examined. The copolymers obtained were characterized by different physicochemical techniques. The copolymers with 10–25 mol % BPPD were semicrystalline and had remarkably increased T_gs over commercially available PEEK and PEKK due to the incorporation of amide linkages in the main chains. The copolymers III and IV with 20–25 mol % BPPD had not only high T_gs of 184–188°C, but also moderate T_ms of 323–344°C, having good potential for the melt processing. The copolymers III and IV had tensile strengths of 103.7–105.3 MPa, Young's moduli of 3.04–3.11 GPa, and elongations at break of 8–9% and exhibited outstanding thermal stability and good resistance to organic solvents. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Thermal analysis,glass transition temperature and rheological behaviour of emulsion copolymers of methyl methacrylate with styrene

Poly(MMA‐ran‐St) samples were synthesized under monomer‐starved conditions (drop feeding method) by emulsion copolymerization. Their thermostability was determined by thermogravimetric analysis. The glass transition temperature (T_g) of the copolymers was determined by differential scanning calorimetry (DSC) and torsional braid analysis (TBA). The results showed that the MMA–St copolymers exhibit an asymmetric T_g versus composition curve, which could not be interpreted by Johnston's equation, taking the different contributions of the diads to the T_g of the copolymer into consideration. A new sequence distribution equation taking into account the different contributions of the triads was proposed to predict the copolymer T_g. The new equation fitted the experimental data exactly. The T_g determined by torsional braid analysis (TBA) is higher than the one determined by DSC, but the difference is not constant. The rheological behaviour of the copolymers was also studied and T_gTBA‐T_gDSC increased with the increasing flow index of the copolymer. © 2003 Society of Chemical Industry     

Preparation of cellulose graft copolymers having polypeptide side chains and their blood compatibility

Blood compatibility of cellulose graft copolymers with poly(γ-benzyl-L -glutamate) and poly(N⁵-2-hydroxyethyl-L -glutamine) (Cell-g-PBLG and Cell-g-PHEG) was examined in vivo blood tests. For this purpose, Cell-g-PBLG graft copolymers with PBLG contents ranging from 7 to 60 mol % were prepared by polymerizing N-carboxy-γ-benzyl-L-glutamate(γ-BLG NCA) using aminoethyl cellulose (AE-Cell) with degree of substitution of 0.05 as macroinitiator. Graft copolymerization was carried out under a variety of conditions at 20°C in dimethyl-sulfoxide. Monomer conversion higher than 60% were obtained for all the polymerization runs. The solubility tests revealed that all of the AE-Cell and the polypeptides formed were grafted. The Cell-g-PHEG graft copolymers were prepared by treating Cell-g-PBLG graft copolymers with 2-amino-1-ethanol. Characterization of these graft copolymers were carried out by IR spectroscopy, DSC, and water content measurement. Tests for blood compatibility, in vivo, were made by a method of peripheral vein indwelling suture which was developed by one of the authors. The coating of graft copolymers on the polyester suture was made by casting either from formic acid solution of LiCl/dimethylacetamide solutions using water as the regenerating medium, and the polymer-coated sutures were implanted into a jugular and femoral vein of a dog. The results showed that the graft copolymers examined have excellent antithrombogenic properties.     

Preparation and characterization of copolymers containing (+)‐bornyl methacrylate and their racemate for positive‐tone photoresist

This study investigated the chemical behavior of polymers bearing cycloaliphatic bornyl units along with the steric difference of the chiral (+)‐bornyl methacrylate [(+)‐BMA] and racemic (±)‐BMA, expressed in the physical properties of the copolymers and the resist characteristics. To do this, a series of copolymers containing (+)‐bornyl methacrylate [(+)‐BMA] and (±)‐BMA] units was synthesized. Comonomers of tert‐butyl methacrylate (TBMA), methyl methacrylate (MMA), and maleic anhydride (MA) were used. The thermogravimetric curves, glass‐transition temperature (T_g), and molecular weight (MW) of the copolymers were evaluated. Exposure characteristics of chemical‐amplified positive photoresists comprising various copolymers were investigated. It was found that copolymers bearing (±)‐BMA have higher T_g and better thermostability than those of copolymers containing (+)‐BMA units. The copolymers with (±)‐BMA units, however, revealed an inert photochemical behavior on the positive‐tone photoresist. The patterning properties of the positive photoresist, composed of copolymers bearing (+)‐BMA and (±)‐BMA, and the photoacid generator (PAG) were also investigated. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 3538–3544, 2001     

Oxygen barrier properties of PET copolymers containing bis(2‐hydroxyethyl)hydroquinones

A series of poly[ethylene‐co‐bis(2‐ethoxy)hydroquinone terephthalate], PET‐co‐BEHQ copolymers were prepared by polymerization of various substituted bis(2‐hydroxyethyl)hydroquinones (BEHQs), dimethyl terephthalate (DMT), and ethylene glycol (EG). In addition to copolymers containing 6–16.5 mol % BEHQ, the homopolymer of BEHQ with dimethyl terephthalate, p(BEHQ‐T), was also prepared. The thermal and barrier properties of amorphous materials were studied. As the amount of comonomer was increased, the T_g and T_m of the materials decreased relative to those of PET. Oxygen permeability also decreased with increasing comonomer content. This improvement in barrier‐to‐oxygen permeability was primarily due to a decrease in solubility of oxygen in the polymer. All of the copolymers tested displayed similar oxygen diffusion coefficients. The decrease in solubility correlates with the decrease in T_g. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 934–942, 2003     

Cellulose furoate. III. Properties and applications

Cellulose furoates synthesized by a homogeneous reaction was used to make film and fiber. Either colorless or light yellow, transparent cellulose furoate film can be made by solvent cast. Cellulose furoate film with a DS of 2.56 and 20% PEG-400 as the plasticizer displayed 5441 psi maximum tenacity and 21.5% maximum strain. The film without plasticizer has a water vapor permeability of 0.124 ng · m/m² · s · Pa. DMTA study identified the T_g of cellulose furoate with a DS of 2.77 was 225°C. As the DS decreased, the T_g shifted toward higher temperature. The success of wet-spun fibers from LiCl/DMAc solution of cellulose and cellulose furoate substantiated cellulose furoate is compatible with cellulose. Unfortunately, the wet-spun fibers lost their mechanical and surface properties, and bioresistant property against Myrothecium verrucaria, Cheatomium globosum, and Aspergillus terreus. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 253–257, 2001     

Synthesis and absorbency of a superabsorbent from sodium starch sulfate‐g‐polyacrylonitrile

A sodium starch sulfate–based superabsorbent was synthesized to improve water and saline absorbencies. A sodium starch sulfate with high degree of substitution was synthesized by the reaction of starch gelatinized with dimethyl acetamide (DMAc)/lithium chloride (LiCl) and a dimethyl formamide–sulfur trioxide (DMF–SO₃) complex. The sodium starch sulfate was then graft‐polymerized with acrylonitrile and the nitrile groups of the sodium starch sulfate‐g‐polyacrylonitrile were converted to a mixture of hydrophilic carboxamide and carboxylate groups by alkaline hydrolysis. The hydrolyzed sodium starch sulfate‐g‐polyacrylonitrile copolymer exhibited improved water and saline absorbencies compared with that of existing starch‐based superabsorbents, resulting from the presence of sulfate groups. The maximum water and saline absorbencies of the sodium starch sulfate–based superabsorbent were 1510 and 126.4 g/g, respectively. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1423–1430, 2001     

One‐pot synthesis of polyetherimides from bis(chlorophthalimide) and dichlorodiphenylsulfone in diphenylsulfone

Polyetherimides and copolymers have been synthesized in one pot from bis(chlorophthalimide), dichlorodiphenylsulfone, and bisphenolate using diphenylsulfone as the solvent. The inherent viscosities of the obtained polyimides are in the range of 0.32–0.72 dL/g, and the structures of polyimides were confirmed by IR and elemental analyses. All of the polyimides have good solubility in common organic solvents. The 5% weight‐loss temperatures of the polyimides were 429–507°C in air. The glass transition temperatures (T_g) of 4,4′‐(9‐fluorenylidene) diphenol‐based polyimides are in the range of 253–268°C. The T_g of bisphenol A‐based polyimides is in the range of 198–204°C, while the T_g change inconspicuously when the ratios of diphenylsulfone increase. The wide‐angle X‐ray diffraction showed that all polyimides prepared are amorphous. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4584–4588, 2006     

Properties and crystallization kinetics of poly(ether ether ketone)‐co‐poly(ether ether ketone ketone) block copolymers

A series of block copolymers composed of poly(ether ether ketone) (PEEK) and poly(ether ether ketone ketone) (PEEKK) components were prepared from their corresponding oligomers via a nucleophlilic aromatic substitution reaction. Various properties of the copolymers were investigated with differential scanning calorimetry (DSC) and a tensile testing machine. The results show that the copolymers exhibited no phase separation and that the relationship between the glass‐transition temperature (T_g) and the compositions of the copolymers approximately followed the formula T_g = T_g1X₁ + T_g2X₂, where T_g1 and T_g2 are the glass‐transition‐temperature values of PEEK and PEEKK, respectively, and X₁ and X₂ are the corresponding molar fractions of the PEEK and PEEKK segments in the copolymers, respectively. These copolymers showed good tensile properties. The crystallization kinetics of the copolymers were studied. The Avrami equation was used to describe the isothermal crystallization process. The nonisothermal crystallization was described by modified Avrami analysis by Jeziorny and by a combination of the Avrami and Ozawa equations. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1652–1658, 2005     

Internal plasticization of poly(vinyl chloride) by grafting acrylate copolymers via copper-mediated atom transfer radical polymerization

Internal plasticization of poly(vinyl chloride) (PVC) was achieved in one-step using copper-mediated atom transfer radical polymerization to graft different ratios of random n-butyl acrylate and 2–2-(2-ethoxyethoxy)ethyl acrylate copolymers from defect sites on the PVC chain. Five graft polymers were made with different ratios of poly(butyl acrylate) (PBA) and poly(2–2-(2-ethoxyethoxy)ethyl acrylate) (P2EEA); the glass transition temperatures (T_g) of functionalized PVC polymers range from − 25 to − 50°C. Single T_g values were observed for all polymers, indicating good compatibility between PVC and grafted chains, with no evidence of microphase separation. Plasticization efficiency is higher for polyether P2EEA moieties compared with PBA components. The resultant PVC graft copolymers are thermally more stable compared to unmodified PVC. Increasing the reaction scale from 2 to 14 g produces consistent and reproducible results, suggesting this method could be applicable on an industrial scale.     

Thermal properties and biodegradability of the copolymers of l-lactide, ?-caprolactone, and ethylene glycol oligomer with maleate units and their crosslinked products

Copolymers of l-lactide (LLA), ?-caprolactone (CL), and ethylene glycol oligomer (EGO) were synthesized by ring-opening copolymerization of CL and LLA initiated by EGO at the LLA/CL molar ratios of 7/3, 5/5, and 3/7. The resulting viscous ternary copolymers (PLCE) with weight average molecular weight (M_w) ca. 3000 were reacted with maleic anhydride to give unsaturated group-containing copolymer (PLCEM) with M_w 6000-8000. The degree of unsaturation of PLCEM was 0.3-0.6 per one EGO block. The PLCEM was cured with benzoyl peroxide (BPO) to give a viscoelastic soft material insoluble in any solvent. The DSC analysis of the copolymers revealed that all the copolymers are amorphous materials having a glass transition temperature (T_g), which increased with increasing LLA/CL ratio. The crosslinked PLCEM showed a higher T_g than the corresponding PLCE and PLCEM. The crosslinked PLCEM showed good biodegradability, when measured by a BOD method using activated sludge.     

Studies of crosslinked styrene–alkyl acrylate copolymers for oil absorbency application. I. Synthesis and characterization

The prepolymers for a novel oil absorbent were synthesized by copolymerizing styrene with 2‐ethylhexyl acrylate (EHA), lauryl acrylate (LA), lauryl methacrylate (LMA), and stearyl acrylate (SA). Suspension polymerization was carried out using benzoyl peroxide (BPO) as an initiator with a varying monomer feed ratio, and the copolymers were characterized by FTIR, ¹H‐NMR, DSC, and a solubility test. The copolymers were random copolymers with a single phase, and their compositions were similar to those in the monomer feed. The T_g of the copolymer could be controlled by varying the styrene/acrylate ratio. Acrylates introduced the crosslinking to linear polymers as a side reaction. Crosslinked copolymers were synthesized by adding divinylbenzene (DVB) as a crosslinking agent. At a low degree of crosslinking (0.5 wt % DVB), the T_g of the crosslinked copolymers was lower than or similar to that of the uncrosslinked ones. At a high degree of crosslinking, the T_g increased with increasing crosslinking density. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 903–913, 2000     

Synthesis and characterization of soluble copoly(arylene ether sulfone phenyl-s-triazine)s containing phthalazinone moieties in the main chain

A series of new poly(arylene ether sulfone phenyl-s-triazine) copolymers containing phthalazinone moieties in the main chain (PPESPs) were prepared by a direct solution polycondensation of 4-(4-hydroxylphenyl)(2H)-phthalazin-1-one (HPPZ) with 2-phenyl-4,6-bi(4-fluorophenyl)-1,3,5-triazine (BFPT) and 4,4′-dichlorodiphenyl sulfone (DCS). Model reactions monitored by HPLC indicated that BFPT had slightly higher reactivity than DCS in nucleophilic displacement reactions. The obtained random copolymers were characterized by FTIR, NMR, elemental analysis and GPC. The presence of sulfone and phthalazinone in the polymer chain results in an improvement in the solubility of poly(arylene ether phenyl-s-triazine)s in common organic solvents, such as N-methylpyrrolidone, N,N-dimethyl acetamide (DMAc), chloroform, sulfolane and pyridine. Thermal analysis reveal that the copolymers exhibit high glass transition temperatures (T_gs) ranging from 271–300 °C, and excellent thermal stability associated with decomposition temperatures for 5% mass-loss exceeding 503 °C. All copolymers are amorphous except PPESP28 as evidenced by WAXD. Their T_gs and solubility increase with an increase in sulfone content in the polymer backbone, while the crystallinity and overall thermal stability appear to decrease. This kind of phthalazinone-based copoly(arylene ether sulfone phenyl-s-triazine)s may be considered a good candidate for using as high-performance structural materials.     

Thermal behavior of nylon 6 copolyamides containing aromatic rings

The thermal behavior of terpolymers of caprolactam (CL) and of hexamethylenediammonium isophthalate (IH) and terephthalate (TH) has been studied in a wide range of compositions by differential thermal analysis. It has been found that either amorphous or crystalline polymers having different crystallization rates can be obtained by changing the composition. The dependence of melting points and glass transition temperatures on the composition has been investigated. The dependence of T_g on the composition for the copolymers CL–IH, IH–TH, and CL–TH has been described by means of the Gordon-Taylor equation. It has been found that this equation fits the experimental data for the IH–TH system only if a parameter which takes into account interactions between the monomeric units is introduced. A ternary iso-T_g map has been obtained through statistical analysis. The influence of the chain stiffness and bulkiness of the monomers on the glass transition temperature is discussed.